commit f3dccdaade upstream.
The AMD PLL USB quirk is incorrectly enabled on newer Ryzen
chipsets. The logic in usb_amd_find_chipset_info currently checks
for unaffected chipsets rather than affected ones. This broke
once a new chipset was added in e788787ef. It makes more sense
to reverse the logic so it won't need to be updated as new
chipsets are added. Note that the core of the workaround in
usb_amd_quirk_pll does correctly check the chipset.
Signed-off-by: Ryan Kennedy <ryan5544@gmail.com>
Fixes: e788787ef4 ("usb:xhci:Add quirk for Certain failing HP keyboard on reset after resume")
Cc: stable <stable@vger.kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20190704153529.9429-2-ryan5544@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 508595515f ]
In some cases the "Allocate & copy" block in ffs_epfile_io() is not
executed. Consequently, in such a case ffs_alloc_buffer() is never called
and struct ffs_io_data is not initialized properly. This in turn leads to
problems when ffs_free_buffer() is called at the end of ffs_epfile_io().
This patch uses kzalloc() instead of kmalloc() in the aio case and memset()
in non-aio case to properly initialize struct ffs_io_data.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5617592927 ]
If the device rejects the control transfer to enable device-initiated
U1/U2 entry, then the device will not initiate U1/U2 transition. To
improve the performance, the downstream port should not initate
transition to U1/U2 to avoid the delay from the device link command
response (no packet can be transmitted while waiting for a response from
the device). If the device has some quirks and does not implement U1/U2,
it may reject all the link state change requests, and the downstream
port may resend and flood the bus with more requests. This will affect
the device performance even further. This patch disables the
hub-initated U1/U2 if the device-initiated U1/U2 entry fails.
Reference: USB 3.2 spec 7.2.4.2.3
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit e244c4699f upstream.
With Link Power Management (LPM) enabled USB3 links transition to low
power U1/U2 link states from U0 state automatically.
Current hub code detects USB3 remote wakeups by checking if the software
state still shows suspended, but the link has transitioned from suspended
U3 to enabled U0 state.
As it takes some time before the hub thread reads the port link state
after a USB3 wake notification, the link may have transitioned from U0
to U1/U2, and wake is not detected by hub code.
Fix this by handling U1/U2 states in the same way as U0 in USB3 wakeup
handling
This patch should be added to stable kernels since 4.13 where LPM was
kept enabled during suspend/resume
Cc: <stable@vger.kernel.org> # v4.13+
Signed-off-by: Lee, Chiasheng <chiasheng.lee@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b2357839c5 upstream.
The old commit 6e4b74e469 ("usb: renesas: fix scheduling in atomic
context bug") fixed an atomic issue by using workqueue for the shdmac
dmaengine driver. However, this has a potential race condition issue
between the work pending and usbhsg_ep_free_request() in gadget mode.
When usbhsg_ep_free_request() is called while pending the queue,
since the work_struct will be freed and then the work handler is
called, kernel panic happens on process_one_work().
To fix the issue, if we could call cancel_work_sync() at somewhere
before the free request, it could be easy. However,
the usbhsg_ep_free_request() is called on atomic (e.g. f_ncm driver
calls free request via gether_disconnect()).
For now, almost all users are having "USB-DMAC" and the DMAengine
driver can be used on atomic. So, this patch adds a workaround for
a race condition to call the DMAengine APIs without the workqueue.
This means we still have TODO on shdmac environment (SH7724), but
since it doesn't have SMP, the race condition might not happen.
Fixes: ab330cf388 ("usb: renesas_usbhs: add support for USB-DMAC")
Cc: <stable@vger.kernel.org> # v4.1+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d29fcf7078 upstream.
On spin lock release in rx_submit, gether_disconnect get a chance to
run, it makes port_usb NULL, rx_submit access NULL port USB, hence null
pointer crash.
Fixed by releasing the lock in rx_submit after port_usb is used.
Fixes: 2b3d942c48 ("usb ethernet gadget: split out network core")
Cc: <stable@vger.kernel.org>
Signed-off-by: Kiruthika Varadarajan <Kiruthika.Varadarajan@harman.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit fbc318afad ]
Gadget drivers may queue request in interrupt context. This would lead to
a descriptor allocation in that context. In that case we would hit
BUG_ON(in_interrupt()) in __get_vm_area_node.
Also remove the unnecessary cast.
Acked-by: Sylvain Lemieux <slemieux.tyco@gmail.com>
Tested-by: James Grant <jamesg@zaltys.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 62fd0e0a24 ]
There is no deallocation of fusb300->ep[i] elements, allocated at
fusb300_probe.
The patch adds deallocation of fusb300->ep array elements.
Signed-off-by: Young Xiao <92siuyang@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit c19dffc0a9 upstream.
An endpoint conflict occurs when the USB is working in device mode
during an isochronous communication. When the endpointA IN direction
is an isochronous IN endpoint, and the host sends an IN token to
endpointA on another device, then the OUT transaction may be missed
regardless the OUT endpoint number. Generally, this occurs when the
device is connected to the host through a hub and other devices are
connected to the same hub.
The affected OUT endpoint can be either control, bulk, isochronous, or
an interrupt endpoint. After the OUT endpoint is primed, if an IN token
to the same endpoint number on another device is received, then the OUT
endpoint may be unprimed (cannot be detected by software), which causes
this endpoint to no longer respond to the host OUT token, and thus, no
corresponding interrupt occurs.
There is no good workaround for this issue, the only thing the software
could do is numbering isochronous IN from the highest endpoint since we
have observed most of device number endpoint from the lowest.
Cc: <stable@vger.kernel.org> #v3.14+
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Greg KH <gregkh@linuxfoundation.org>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Cc: Jun Li <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bd21f0222a upstream.
This patch fixes the chipmunk-like voice that manifets randomly when
using the integrated mic of the Logitech Webcam HD C270.
The issue was solved initially for this device by commit 2394d67e44
("USB: add RESET_RESUME for webcams shown to be quirky") but it was then
reintroduced by e387ef5c47 ("usb: Add USB_QUIRK_RESET_RESUME for all
Logitech UVC webcams"). This patch is to have the fix back.
Signed-off-by: Marco Zatta <marco@zatta.me>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4a4863bf2e upstream.
Insert a padding between data and the stored_xfer_buffer pointer to
ensure they are not on the same cache line.
Otherwise, the stored_xfer_buffer gets corrupted for IN URBs on
non-cache-coherent systems. (In my case: Lantiq xRX200 MIPS)
Fixes: 3bc04e28a0 ("usb: dwc2: host: Get aligned DMA in a more supported way")
Fixes: 56406e017a ("usb: dwc2: Fix DMA alignment to start at allocated boundary")
Cc: <stable@vger.kernel.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ea26111338 upstream.
Without USB_QUIRK_NO_LPM ethernet will not work and rtl8152 will
complain with
r8152 <device...>: Stop submitting intr, status -71
Adding the quirk resolves this. As the dock is externally powered, this
should not have any drawbacks.
Signed-off-by: Maximilian Luz <luzmaximilian@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a03ff54460 upstream.
The syzkaller USB fuzzer found a slab-out-of-bounds write bug in the
USB core, caused by a failure to check the actual size of a BOS
descriptor. This patch adds a check to make sure the descriptor is at
least as large as it is supposed to be, so that the code doesn't
inadvertently access memory beyond the end of the allocated region
when assigning to dev->bos->desc->bNumDeviceCaps later on.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: syzbot+71f1e64501a309fcc012@syzkaller.appspotmail.com
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3ea3091f1b upstream.
Fix the following sparse context imbalance regression introduced in
a patch that fixed sleeping function called from invalid context bug.
kbuild test robot reported on:
tree/branch: https://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb.git usb-linus
Regressions in current branch:
drivers/usb/usbip/stub_dev.c:399:9: sparse: sparse: context imbalance in 'stub_probe' - different lock contexts for basic block
drivers/usb/usbip/stub_dev.c:418:13: sparse: sparse: context imbalance in 'stub_disconnect' - different lock contexts for basic block
drivers/usb/usbip/stub_dev.c:464:1-10: second lock on line 476
Error ids grouped by kconfigs:
recent_errors
├── i386-allmodconfig
│ └── drivers-usb-usbip-stub_dev.c:second-lock-on-line
├── x86_64-allmodconfig
│ ├── drivers-usb-usbip-stub_dev.c:sparse:sparse:context-imbalance-in-stub_disconnect-different-lock-contexts-for-basic-block
│ └── drivers-usb-usbip-stub_dev.c:sparse:sparse:context-imbalance-in-stub_probe-different-lock-contexts-for-basic-block
└── x86_64-allyesconfig
└── drivers-usb-usbip-stub_dev.c:second-lock-on-line
This is a real problem in an error leg where spin_lock() is called on an
already held lock.
Fix the imbalance in stub_probe() and stub_disconnect().
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Fixes: 0c9e8b3cad ("usbip: usbip_host: fix BUG: sleeping function called from invalid context")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f7fac17ca9 upstream.
Xhci_handshake() implements the algorithm already captured by
readl_poll_timeout_atomic(). Convert the former to use the latter to
avoid repetition.
Turned out this patch also fixes a bug on the AMD Stoneyridge platform
where usleep(1) sometimes takes over 10ms.
This means a 5 second timeout can easily take over 15 seconds which will
trigger the watchdog and reboot the system.
[Add info about patch fixing a bug to commit message -Mathias]
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Tested-by: Raul E Rangel <rrangel@chromium.org>
Reviewed-by: Raul E Rangel <rrangel@chromium.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c1a145a3ed upstream.
Commit 597c56e372 ("xhci: update bounce buffer with correct sg num")
caused the following build warnings:
drivers/usb/host/xhci-ring.c:676:19: warning: format '%ld' expects argument of type 'long int', but argument 3 has type 'size_t {aka unsigned int}' [-Wformat=]
Use %zu for printing size_t type in order to fix the warnings.
Fixes: 597c56e372 ("xhci: update bounce buffer with correct sg num")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 597c56e372 upstream.
This change fixes a data corruption issue occurred on USB hard disk for
the case that bounce buffer is used during transferring data.
While updating data between sg list and bounce buffer, current
implementation passes mapped sg number (urb->num_mapped_sgs) to
sg_pcopy_from_buffer() and sg_pcopy_to_buffer(). This causes data
not get copied if target buffer is located in the elements after
mapped sg elements. This change passes sg number for full list to
fix issue.
Besides, for copying data from bounce buffer, calling dma_unmap_single()
on the bounce buffer before copying data to sg list can avoid cache issue.
Fixes: f9c589e142 ("xhci: TD-fragment, align the unsplittable case with a bounce buffer")
Cc: <stable@vger.kernel.org> # v4.8+
Signed-off-by: Henry Lin <henryl@nvidia.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8ead7e8172 ]
If ohci-platform is runtime suspended, we can currently get an "imprecise
external abort" on reboot with ohci-platform loaded when PM runtime
is implemented for the SoC.
Let's fix this by adding PM runtime support to usb_hcd_platform_shutdown.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 381419fa72 ]
The SCSI core does not like to have devices or hosts unregistered
while error recovery is in progress. Trying to do so can lead to
self-deadlock: Part of the removal code tries to obtain a lock already
held by the error handler.
This can cause problems for the usb-storage and uas drivers, because
their error handler routines perform a USB reset, and if the reset
fails then the USB core automatically goes on to unbind all drivers
from the device's interfaces -- all while still in the context of the
SCSI error handler.
As it turns out, practically all the scenarios leading to a USB reset
failure end up causing a device disconnect (the main error pathway in
usb_reset_and_verify_device(), at the end of the routine, calls
hub_port_logical_disconnect() before returning). As a result, the
hub_wq thread will soon become aware of the problem and will unbind
all the device's drivers in its own context, not in the
error-handler's context.
This means that usb_reset_device() does not need to call
usb_unbind_and_rebind_marked_interfaces() in cases where
usb_reset_and_verify_device() has returned an error, because hub_wq
will take care of everything anyway.
This particular problem was observed in somewhat artificial
circumstances, by using usbfs to tell a hub to power-down a port
connected to a USB-3 mass storage device using the UAS protocol. With
the port turned off, the currently executing command timed out and the
error handler started running. The USB reset naturally failed,
because the hub port was off, and the error handler deadlocked as
described above. Not carrying out the call to
usb_unbind_and_rebind_marked_interfaces() fixes this issue.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Kento Kobayashi <Kento.A.Kobayashi@sony.com>
Tested-by: Kento Kobayashi <Kento.A.Kobayashi@sony.com>
CC: Bart Van Assche <bvanassche@acm.org>
CC: Martin K. Petersen <martin.petersen@oracle.com>
CC: Jacky Cao <Jacky.Cao@sony.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 3f5edd58d0 upstream.
Fix two long-standing bugs which could potentially lead to memory
corruption or leave the port throttled until it is reopened (on weakly
ordered systems), respectively, when read-URB completion races with
unthrottle().
First, the URB must not be marked as free before processing is complete
to prevent it from being submitted by unthrottle() on another CPU.
CPU 1 CPU 2
================ ================
complete() unthrottle()
process_urb();
smp_mb__before_atomic();
set_bit(i, free); if (test_and_clear_bit(i, free))
submit_urb();
Second, the URB must be marked as free before checking the throttled
flag to prevent unthrottle() on another CPU from failing to observe that
the URB needs to be submitted if complete() sees that the throttled flag
is set.
CPU 1 CPU 2
================ ================
complete() unthrottle()
set_bit(i, free); throttled = 0;
smp_mb__after_atomic(); smp_mb();
if (throttled) if (test_and_clear_bit(i, free))
return; submit_urb();
Note that test_and_clear_bit() only implies barriers when the test is
successful. To handle the case where the URB is still in use an explicit
barrier needs to be added to unthrottle() for the second race condition.
Fixes: d83b405383 ("USB: serial: add support for multiple read urbs")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3ae62a4209 upstream.
This is the UAS version of
747668dbc0
usb-storage: Set virt_boundary_mask to avoid SG overflows
We are not as likely to be vulnerable as storage, as it is unlikelier
that UAS is run over a controller without native support for SG,
but the issue exists.
The issue has been existing since the inception of the driver.
Fixes: 115bb1ffa5 ("USB: Add UAS driver")
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 747668dbc0 upstream.
The USB subsystem has always had an unusual requirement for its
scatter-gather transfers: Each element in the scatterlist (except the
last one) must have a length divisible by the bulk maxpacket size.
This is a particular issue for USB mass storage, which uses SG lists
created by the block layer rather than setting up its own.
So far we have scraped by okay because most devices have a logical
block size of 512 bytes or larger, and the bulk maxpacket sizes for
USB 2 and below are all <= 512. However, USB 3 has a bulk maxpacket
size of 1024. Since the xhci-hcd driver includes native SG support,
this hasn't mattered much. But now people are trying to use USB-3
mass storage devices with USBIP, and the vhci-hcd driver currently
does not have full SG support.
The result is an overflow error, when the driver attempts to implement
an SG transfer of 63 512-byte blocks as a single
3584-byte (7 blocks) transfer followed by seven 4096-byte (8 blocks)
transfers. The device instead sends 31 1024-byte packets followed by
a 512-byte packet, and this overruns the first SG buffer.
Ideally this would be fixed by adding better SG support to vhci-hcd.
But for now it appears we can work around the problem by
asking the block layer to respect the maxpacket limitation, through
the use of the virt_boundary_mask.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Seth Bollinger <Seth.Bollinger@digi.com>
Tested-by: Seth Bollinger <Seth.Bollinger@digi.com>
CC: Ming Lei <tom.leiming@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 804dbee1e4 upstream.
The F81232 will use interrupt worker to handle MSR change.
This patch will fix the issue that interrupt work should stop
in close() and suspend().
This also fixes line-status events being disabled after a suspend cycle
until the port is re-opened.
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
[ johan: amend commit message ]
Fixes: 87fe5adcd8 ("USB: f81232: implement read IIR/MSR with endpoint")
Cc: stable <stable@vger.kernel.org> # 4.1
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c2b71462d2 upstream.
The syzkaller fuzzer reported a bug in the USB hub driver which turned
out to be caused by a negative runtime-PM usage counter. This allowed
a hub to be runtime suspended at a time when the driver did not expect
it. The symptom is a WARNING issued because the hub's status URB is
submitted while it is already active:
URB 0000000031fb463e submitted while active
WARNING: CPU: 0 PID: 2917 at drivers/usb/core/urb.c:363
The negative runtime-PM usage count was caused by an unfortunate
design decision made when runtime PM was first implemented for USB.
At that time, USB class drivers were allowed to unbind from their
interfaces without balancing the usage counter (i.e., leaving it with
a positive count). The core code would take care of setting the
counter back to 0 before allowing another driver to bind to the
interface.
Later on when runtime PM was implemented for the entire kernel, the
opposite decision was made: Drivers were required to balance their
runtime-PM get and put calls. In order to maintain backward
compatibility, however, the USB subsystem adapted to the new
implementation by keeping an independent usage counter for each
interface and using it to automatically adjust the normal usage
counter back to 0 whenever a driver was unbound.
This approach involves duplicating information, but what is worse, it
doesn't work properly in cases where a USB class driver delays
decrementing the usage counter until after the driver's disconnect()
routine has returned and the counter has been adjusted back to 0.
Doing so would cause the usage counter to become negative. There's
even a warning about this in the USB power management documentation!
As it happens, this is exactly what the hub driver does. The
kick_hub_wq() routine increments the runtime-PM usage counter, and the
corresponding decrement is carried out by hub_event() in the context
of the hub_wq work-queue thread. This work routine may sometimes run
after the driver has been unbound from its interface, and when it does
it causes the usage counter to go negative.
It is not possible for hub_disconnect() to wait for a pending
hub_event() call to finish, because hub_disconnect() is called with
the device lock held and hub_event() acquires that lock. The only
feasible fix is to reverse the original design decision: remove the
duplicate interface-specific usage counter and require USB drivers to
balance their runtime PM gets and puts. As far as I know, all
existing drivers currently do this.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: syzbot+7634edaea4d0b341c625@syzkaller.appspotmail.com
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c01c348ecd upstream.
Some drivers (such as the vub300 MMC driver) expect usb_string() to
return a properly NUL-terminated string, even when an error occurs.
(In fact, vub300's probe routine doesn't bother to check the return
code from usb_string().) When the driver goes on to use an
unterminated string, it leads to kernel errors such as
stack-out-of-bounds, as found by the syzkaller USB fuzzer.
An out-of-range string index argument is not at all unlikely, given
that some devices don't provide string descriptors and therefore list
0 as the value for their string indexes. This patch makes
usb_string() return a properly terminated empty string along with the
-EINVAL error code when an out-of-range index is encountered.
And since a USB string index is a single-byte value, indexes >= 256
are just as invalid as values of 0 or below.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: syzbot+b75b85111c10b8d680f1@syzkaller.appspotmail.com
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c409ca3be3 upstream.
Change the validation of number_of_packets in get_pipe to compare the
number of packets to a fixed maximum number of packets allowed, set to
be 1024. This number was chosen due to it being used by other drivers as
well, for example drivers/usb/host/uhci-q.c
Background/reason:
The get_pipe function in stub_rx.c validates the number of packets in
isochronous mode and aborts with an error if that number is too large,
in order to prevent malicious input from possibly triggering large
memory allocations. This was previously done by checking whether
pdu->u.cmd_submit.number_of_packets is bigger than the number of packets
that would be needed for pdu->u.cmd_submit.transfer_buffer_length bytes
if all except possibly the last packet had maximum length, given by
usb_endpoint_maxp(epd) * usb_endpoint_maxp_mult(epd). This leads to an
error if URBs with packets shorter than the maximum possible length are
submitted, which is allowed according to
Documentation/driver-api/usb/URB.rst and occurs for example with the
snd-usb-audio driver.
Fixes: c6688ef9f2 ("usbip: fix stub_rx: harden CMD_SUBMIT path to handle malicious input")
Signed-off-by: Malte Leip <malte@leip.net>
Cc: stable <stable@vger.kernel.org>
Acked-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ef61eb43ad upstream.
The syzkaller USB fuzzer found a general-protection-fault bug in the
yurex driver. The fault occurs when a device has been unplugged; the
driver's interrupt-URB handler logs an error message referring to the
device by name, after the device has been unregistered and its name
deallocated.
This problem is caused by the fact that the interrupt URB isn't
cancelled until the driver's private data structure is released, which
can happen long after the device is gone. The cure is to make sure
that the interrupt URB is killed before yurex_disconnect() returns;
this is exactly the sort of thing that usb_poison_urb() was meant for.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: syzbot+2eb9121678bdb36e6d57@syzkaller.appspotmail.com
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 091dacc3cc ]
Restore the status of ep->stopped in function net2272_dequeue().
When the given request is not found in the endpoint queue
the function returns -EINVAL without restoring the state of
ep->stopped. Thus the endpoint keeps blocked and does not transfer
any data anymore.
This fix is only compile-tested, since we do not have a
corresponding hardware. An analogous fix was tested in the sibling
driver. See "usb: gadget: net2280: Fix net2280_dequeue()"
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Guido Kiener <guido.kiener@rohde-schwarz.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
[ Upstream commit f1d3fba17c ]
When a request must be dequeued with net2280_dequeue() e.g. due
to a device clear action and the same request is finished by the
function scan_dma_completions() then the function net2280_dequeue()
does not find the request in the following search loop and
returns the error -EINVAL without restoring the status ep->stopped.
Thus the endpoint keeps blocked and does not receive any data
anymore.
This fix restores the status and does not issue an error message.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Guido Kiener <guido.kiener@rohde-schwarz.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
[ Upstream commit 9d6a54c143 ]
The OUT endpoint normally blocks (NAK) subsequent packets when a
short packet was received and returns an incomplete queue entry to
the gadget driver. Thereby the gadget driver can detect a short packet
when reading queue entries with a length that is not equal to a
multiple of packet size.
The start_queue() function enables receiving OUT packets regardless of
the content of the OUT FIFO. This results in a race: With the current
code, it's possible that the "!ep->is_in && (readl(&ep->regs->ep_stat)
& BIT(NAK_OUT_PACKETS))" test in start_dma() will fail, then a short
packet will be received, and then start_queue() will call
stop_out_naking(). That's what we don't want (OUT naking gets turned
off while there is data in the FIFO) because then the next driver
request might receive a mixture of old and new packets.
With the patch, this race can't occur because the FIFO's state is
tested after we know that OUT naking is already turned on, and OUT
naking is stopped only when both of the conditions are met. This
ensures that all received data is delivered to the gadget driver,
which can detect a short packet now before new packets are appended
to the last short packet.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Guido Kiener <guido.kiener@rohde-schwarz.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
commit d7a6c0ce8d upstream.
USB Bluetooth controller QCA ROME (0cf3:e007) sometimes stops working
after S3:
[ 165.110742] Bluetooth: hci0: using NVM file: qca/nvm_usb_00000302.bin
[ 168.432065] Bluetooth: hci0: Failed to send body at 4 of 1953 (-110)
After some experiments, I found that disabling LPM can workaround the
issue.
On some platforms, the USB power is cut during S3, so the driver uses
reset-resume to resume the device. During port resume, LPM gets enabled
twice, by usb_reset_and_verify_device() and usb_port_resume().
Consolidate all checks into new LPM helpers to make sure LPM only gets
enabled once.
Fixes: de68bab4fa ("usb: Don't enable USB 2.0 Link PM by default.”)
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: stable <stable@vger.kernel.org> # after much soaking
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 54f64d5c98 ]
Since the 5.0 merge window opened, I've been seeing frequent
crashes on suspend and reboot with the trace:
[ 36.911170] Unable to handle kernel paging request at virtual address ffffff801153d660
[ 36.912769] Unable to handle kernel paging request at virtual address ffffff800004b564
...
[ 36.950666] Call trace:
[ 36.950670] queued_spin_lock_slowpath+0x1cc/0x2c8
[ 36.950681] _raw_spin_lock_irqsave+0x64/0x78
[ 36.950692] complete+0x28/0x70
[ 36.950703] ffs_epfile_io_complete+0x3c/0x50
[ 36.950713] usb_gadget_giveback_request+0x34/0x108
[ 36.950721] dwc3_gadget_giveback+0x50/0x68
[ 36.950723] dwc3_thread_interrupt+0x358/0x1488
[ 36.950731] irq_thread_fn+0x30/0x88
[ 36.950734] irq_thread+0x114/0x1b0
[ 36.950739] kthread+0x104/0x130
[ 36.950747] ret_from_fork+0x10/0x1c
I isolated this down to in ffs_epfile_io():
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/drivers/usb/gadget/function/f_fs.c#n1065
Where the completion done is setup on the stack:
DECLARE_COMPLETION_ONSTACK(done);
Then later we setup a request and queue it, and wait for it:
if (unlikely(wait_for_completion_interruptible(&done))) {
/*
* To avoid race condition with ffs_epfile_io_complete,
* dequeue the request first then check
* status. usb_ep_dequeue API should guarantee no race
* condition with req->complete callback.
*/
usb_ep_dequeue(ep->ep, req);
interrupted = ep->status < 0;
}
The problem is, that we end up being interrupted, dequeue the
request, and exit.
But then the irq triggers and we try calling complete() on the
context pointer which points to now random stack space, which
results in the panic.
Alan Stern pointed out there is a bug here, in that the snippet
above "assumes that usb_ep_dequeue() waits until the request has
been completed." And that:
wait_for_completion(&done);
Is needed right after the usb_ep_dequeue().
Thus this patch implements that change. With it I no longer see
the crashes on suspend or reboot.
This issue seems to have been uncovered by behavioral changes in
the dwc3 driver in commit fec9095bde ("usb: dwc3: gadget:
remove wait_end_transfer").
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Zeng Tao <prime.zeng@hisilicon.com>
Cc: Jack Pham <jackp@codeaurora.org>
Cc: Thinh Nguyen <thinh.nguyen@synopsys.com>
Cc: Chen Yu <chenyu56@huawei.com>
Cc: Jerry Zhang <zhangjerry@google.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Vincent Pelletier <plr.vincent@gmail.com>
Cc: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Linux USB List <linux-usb@vger.kernel.org>
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 68ef236274 ]
According to the chipidea driver bindings, the USB PHY is specified via
the "phys" phandle node. However, this only takes effect for USB PHYs
that use the common PHY framework. For legacy USB PHYs, a simple lookup
based on the USB PHY type is done instead.
This does not play out well when more than one USB PHY is registered,
since the first registered PHY matching the type will always be
returned regardless of what the driver was bound to.
Fix this by looking up the PHY based on the "phys" phandle node.
Although generic PHYs are rather matched by their "phys-name" and not
the "phys" phandle directly, there is no helper for similar lookup on
legacy PHYs and it's probably not worth the effort to add it.
When no legacy USB PHY is found by phandle, fallback to grabbing any
registered USB2 PHY. This ensures backward compatibility if some users
were actually relying on this mechanism.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 6cbcf59693 upstream.
A suspended SS port in U3 link state will go to U0 when resumed, but
can almost immediately after that enter U1 or U2 link power save
states before host controller driver reads the port status.
Host controller driver only checks for U0 state, and might miss
the finished resume, leaving flags unclear and skip notifying usb
code of the wake.
Add U1 and U2 to the possible link states when checking for finished
port resume.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
