Interrupt line can be configured on different hardware in different way,
even inverted. Therefore driver should not enforce specific trigger
type - edge falling - but instead rely on Devicetree to configure it.
The Maxim 14577/77836 datasheets describe the interrupt line as active
low with a requirement of acknowledge from the CPU therefore the edge
falling is not correct.
The interrupt line is shared between PMIC and charger driver, so using
level sensitive interrupt is here especially important to avoid races.
With an edge configuration in case if first PMIC signals interrupt
followed shortly after by the RTC, the interrupt might not be yet
cleared/acked thus the second one would not be noticed.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210602110445.33536-4-krzysztof.kozlowski@canonical.com
Interrupt line can be configured on different hardware in different way,
even inverted. Therefore driver should not enforce specific trigger
type - edge falling - but instead rely on Devicetree to configure it.
The Maxim 77693 datasheet describes the interrupt line as active low
with a requirement of acknowledge from the CPU therefore the edge
falling is not correct.
The interrupt line is shared between PMIC and RTC driver, so using level
sensitive interrupt is here especially important to avoid races. With
an edge configuration in case if first PMIC signals interrupt followed
shortly after by the RTC, the interrupt might not be yet cleared/acked
thus the second one would not be noticed.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210602110445.33536-3-krzysztof.kozlowski@canonical.com
Interrupt line can be configured on different hardware in different way,
even inverted. Therefore driver should not enforce specific trigger
type - edge falling - but instead rely on Devicetree to configure it.
The Maxim 77686 datasheet describes the interrupt line as active low
with a requirement of acknowledge from the CPU therefore the edge
falling is not correct.
The interrupt line is shared between PMIC and RTC driver, so using level
sensitive interrupt is here especially important to avoid races. With
an edge configuration in case if first PMIC signals interrupt followed
shortly after by the RTC, the interrupt might not be yet cleared/acked
thus the second one would not be noticed.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210602110445.33536-2-krzysztof.kozlowski@canonical.com
Interrupt line can be configured on different hardware in different way,
even inverted. Therefore driver should not enforce specific trigger
type - edge falling - but instead rely on Devicetree to configure it.
The Samsung PMIC drivers are used only on Devicetree boards.
Additionally, the PMIC datasheets describe the interrupt line as active
low with a requirement of acknowledge from the CPU therefore the edge
falling is not correct.
Marek Szyprowski reports that together with DTS change (proper level in
DTS) it fixes RTC alarm failure that he observed from time to time on
TM2e board.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210602110445.33536-1-krzysztof.kozlowski@canonical.com
The LogiCVC multi-function device has a display part which is now
described in its binding. Add a patternProperties match for it.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The MODULE_DEVICE_TABLE already creates proper alias. Having another
MODULE_ALIAS causes the alias to be duplicated:
$ modinfo cros_ec_dev.ko
alias: platform:cros-ec-dev
srcversion: F84A69D2156719A4F717A76
alias: platform:cros-ec-dev
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The description mentioned AD5520, which is a different device.
Fixed the typo.
Signed-off-by: Ramona Alexandra Nechita <ramona.nechita@analog.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This update adds new regmap to support the latest EA silicon
which will be selected based on the chip and variant
information read from the device.
Signed-off-by: Carlos de Paula <me@carlosedp.com>
Reviewed-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
RK817 has a power-off bit in SYS_CFG3. Add support for powering
off the PMIC.
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The intel_pmt driver shows up as a compile option for all arches but is
32-bit and 64-bit x86 specific.
Add a CONFIG dependency on X86 for intel_pmt.
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Reviewed-by: David E. Box <david.e.box@linux.intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
CRU has a shared register that is used e.g. to control USB 2.0 PHY block
access. It's a single 32 b register. Document it as syscon so it can be
used with a regmap.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Broadcom's MISC is an MFD hardware block used on some of their SoCs like
bcm63xx and bcm4908. At this point only PCIe reset is fully understood
and documented. More functions may be added later.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
fix the remaining build issues reported by patchwork
in firmware v4.0 support commit which has been already
merged.
Fix patchwork issues:
- source inline
- checkpatch
Fixes: bb5dbf2cc6 ("net: marvell: prestera: add firmware v4.0 support")
Signed-off-by: Volodymyr Mytnyk <vmytnyk@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mii ioctls are now handled by the ndo_eth_ioctl() callback,
not the old ndo_do_ioctl(), but octeontx2-nicvf introduced the
function for the old way.
Move it over to ndo_eth_ioctl() to actually allow calling it from
user space.
Fixes: 43510ef4dd ("octeontx2-nicvf: Add PTP hardware clock support to NIX VF")
Fixes: a76053707d ("dev_ioctl: split out ndo_eth_ioctl")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The timestamp ioctls are now handled by the ndo_eth_ioctl() callback,
not the old ndo_do_ioctl(), but oax88796 introduced the
function for the old way.
Move it over to ndo_eth_ioctl() to actually allow calling it from
user space.
Fixes: a97c69ba4f ("net: ax88796c: ASIX AX88796C SPI Ethernet Adapter Driver")
Fixes: a76053707d ("dev_ioctl: split out ndo_eth_ioctl")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Lukasz Stelmach <l.stelmach@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Pericom PI7C9X2G404/PI7C9X2G304/PI7C9X2G303 PCIe switches have an
erratum for ACS P2P Request Redirect behaviour when used in the cut-through
forwarding mode. The recommended work around for this issue is to use the
switch in store and forward mode. The erratum results in packets being
queued and not being delivered upstream, which can be observed as very poor
downstream device performance and/or dropped device-generated
data/interrupts.
Add a fixup so that when enabling or resuming the downstream port we check
if it has enabled ACS P2P Request Redirect, and if so, change the device
(via the upstream port) to use the store and forward operating mode.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=177471
Link: https://lore.kernel.org/r/20210910025823.196508-1-nathan@nathanrossi.com
Tested-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Nathan Rossi <nathan.rossi@digi.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The pwm_ prefix suggests that pwm_busy_wait() is a function provided by
the pwm core. Use the otherwise consistently used driver prefix for this
function, too.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
When duty-cycle is at full level (100%), the TCNTn and TCMPn registers
needs to be flushed in order to disable the signal. The PWM manual does
not say anything about this, but states that only clearing the TCON
auto-reload bit should be needed, and this seems to be true when the PWM
duty-cycle is not at full level. This can be observed on an Axis
ARTPEC-8, by running:
echo <period> > pwm/period
echo <period> > pwm/duty_cycle
echo 1 > pwm/enable
echo 0 > pwm/enable
Since the TCNTn and TCMPn registers are activated when enabling the PWM
(setting TCON auto-reload bit), and are not touched when disabling the
PWM, the double buffered auto-reload function seems to be still active.
Lowering duty-cycle, and restoring it again in between the enabling and
disabling, makes the disable work since it triggers a reload of the
TCNTn and TCMPn registers.
Fix this by securing a reload of the TCNTn and TCMPn registers when
disabling the PWM and having a full duty-cycle.
Signed-off-by: Mårten Lindahl <marten.lindahl@axis.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
At least some implementations sleep. So mark pwm_apply_state() with a
might_sleep() to make callers aware. In the worst case this uncovers a
valid atomic user, then we revert this patch and at least gained some more
knowledge and then can work on a concept similar to
gpio_get_value/gpio_get_value_cansleep.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The normal implementations of these functions make use of mutexes. To
make it obvious that these functions might sleep also add annotations to
the dummy implementations in the !CONFIG_PWM case.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Build bot says:
>> drivers/net/ethernet/asix/ax88796c_main.c:1116:34: warning: unused variable 'ax88796c_dt_ids' [-Wunused-const-variable]
static const struct of_device_id ax88796c_dt_ids[] = {
^
The only reference to this array is wrapped in of_match_ptr().
Reported-by: kernel test robot <lkp@intel.com>
Fixes: a97c69ba4f ("net: ax88796c: ASIX AX88796C SPI Ethernet Adapter Driver")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
udp_mem is a vector of 3 INTEGERs, which is used to limit the number of
pages allowed for queueing by all UDP sockets.
However, sk_has_memory_pressure() in __sk_mem_raise_allocated() always
return false for udp, as memory pressure is not supported by udp, which
means that __sk_mem_raise_allocated() will fail once pages allocated
for udp socket exceeds udp_mem[0].
Therefor, udp_mem[0] is the only one that limit the number of pages.
However, the document of udp_mem just express that udp_mem[2] is the
limitation. So, just fix it.
Signed-off-by: Menglong Dong <imagedong@tencent.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Although we've covered all calls with NULL dma buffer pointer, so far,
there may be still some else in the wild. For catching such a case
more easily, add a WARN_ON_ONCE() in snd_dma_get_ops().
Fixes: 37af81c599 ("ALSA: core: Abstract memory alloc helpers")
Link: https://lore.kernel.org/r/20211105102103.28148-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The print function dev_err() is redundant because
platform_get_irq() already prints an error.
Signed-off-by: Xu Wang <vulab@iscas.ac.cn>
Reviewed-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
