Now that we've removed direct calls from interrupt handler to
omap2430_musb_set_vbus(), let's make things less confusing and
configure VBUS directly in omap_musb_set_mailbox().
We have omap_musb_set_mailbox() called from the PHYs, and that's
all we need.
Note that we can now also drop the check for MUSB_INTERFACE_UTMI,
we've been already calling otg_set_vbus(musb->xceiv->otg, 0)
unconditionally via omap2430_musb_set_vbus() and we should only
need to call it once.
And we want to disable VBUS unconditionally on disconnect even
without musb->gadget_driver, so let's drop that check too.
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Link: https://lore.kernel.org/r/20200115132547.364-11-b-liu@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At least some revisions of musb core need to set devctl session bit
in peripheral mode to force musb to host mode. And we have places
clearing the devctl session bit.
Let's add a generic function to do this, and use it for omap2430.
This should get us a bit closer to completely removing devctl register
tinkering in the SoC glue code.
Before making use of this code for the other glue layers, things need
to be tested carefully as there may be a approximately a 200 ms delay
needed between powering up musb and calling musb_set_host() to avoid.
Otherwise the system hangs at least with omap2430 glue layer.
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
[b-liu@ti.com: fixed "line over 80 characters" warning]
Signed-off-by: Bin Liu <b-liu@ti.com>
Link: https://lore.kernel.org/r/20200115132547.364-8-b-liu@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We currently get "unhandled DISCONNECT transition" warnings from musb core
on device disconnect as things are wrongly set to OTG_STATE_A_IDLE in
host mode when enumerating devices. We can also get "Failed to write reg
index" errors after enumerating.
This is happening at least with cpcap phy where we get multiple ID ground
interrupts. Looks like it's VBUS keeps timing out and needs to be kicked
when the phy sends multiple ID ground interrupts during host mode.
Cc: Jacopo Mondi <jacopo@jmondi.org>
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Michael Scott <hashcode0f@gmail.com>
Cc: NeKit <nekit1000@gmail.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Link: https://lore.kernel.org/r/20200115132547.364-7-b-liu@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We currently have musb_set_vbus() called from two different paths. Mostly
it gets called from the USB PHY via omap_musb_set_mailbox(), but in some
cases it can get also called from musb_stage0_irq() rather via .set_vbus:
(musb_set_host [musb_hdrc])
(omap2430_musb_set_vbus [omap2430])
(musb_stage0_irq [musb_hdrc])
(musb_interrupt [musb_hdrc])
(omap2430_musb_interrupt [omap2430])
This is racy and will not work with introducing generic helper functions
for musb_set_host() and musb_set_peripheral(). We want to get rid of the
busy loops in favor of usleep_range().
Let's just get rid of .set_vbus for omap2430 glue layer and let the PHY
code handle VBUS with musb_set_vbus(). Note that in the follow-up patch
we can completely remove omap2430_musb_set_vbus(), but let's do it in a
separate patch as this change may actually turn out to be needed as a
fix.
Reported-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Link: https://lore.kernel.org/r/20200115132547.364-5-b-liu@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The original dwc_otg driver used a DWC_WORKQ_SCHEDULE() wrapper to queue
work items. Because that wrapper acquired the driver's global spinlock,
an unlock/lock dance was necessary whenever a work item was queued up
while the global spinlock was already held.
The dwc2 driver dropped DWC_WORKQ_SCHEDULE() in favor of a direct call
to queue_work(), but retained the (now gratuitous) unlock/lock dance in
dwc2_handle_conn_id_status_change_intr(). Drop it.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Acked-by: Felipe Balbi <balbi@kernel.org>
Link: https://lore.kernel.org/r/77c07f00a6a9d94323c4a060a3c72817b0703b97.1574244795.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For shared, and read-only private mappings of graphics memory, use
VM_PFNMAP instead of VM_MIXEDMAP. This means less accounting overhead
when inserting and removing page-table entries. TTM doesn't do this
by default, since there was a performance problem with book-keeping of
write-combined mappings. Since vmwgfx solely uses cached mappings, that's
not a problem and now that the TTM vm has largely been turned into
helpers, we can use VM_PFNMAP on a per-driver basis
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Roland Scheidegger <sroland@vmware.com>
Using .st_ctime clobbers the timestamp information in perf report header
whenever any operation is done with the file. Even tar-ing and untar-ing
the perf.data file (which preserves the file last modification timestamp)
doesn't prevent that:
[Michael@Diego tmp]$ ls -l perf.data
-> -rw-------. 1 Michael Michael 169888 Dec 2 15:23 perf.data
[Michael@Diego tmp]$ perf report --header-only
# ========
-> # captured on : Mon Dec 2 15:23:42 2019
[...]
[Michael@Diego tmp]$ tar c perf.data | xz > perf.data.tar.xz
[Michael@Diego tmp]$ mkdir aaa
[Michael@Diego tmp]$ cd aaa
[Michael@Diego aaa]$ xzcat ../perf.data.tar.xz | tar x
[Michael@Diego aaa]$ ls -l -a
total 172
drwxrwxr-x. 2 Michael Michael 23 Jan 14 11:26 .
drwxrwxr-x. 6 Michael Michael 4096 Jan 14 11:26 ..
-> -rw-------. 1 Michael Michael 169888 Dec 2 15:23 perf.data
[Michael@Diego aaa]$ perf report --header-only
# ========
-> # captured on : Tue Jan 14 11:26:16 2020
[...]
When using .st_mtime instead, correct information is printed:
[Michael@Diego aaa]$ ~/acme/tools/perf/perf report --header-only
# ========
-> # captured on : Mon Dec 2 15:23:42 2019
[...]
Signed-off-by: Michael Petlan <mpetlan@redhat.com>
Acked-by: Jiri Olsa <jolsa@kernel.org>
LPU-Reference: 20200114104236.31555-1-mpetlan@redhat.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
As the Kconfig syntax gained support for $(as-instr) tests, move the LSE
gas support detection from Makefile to the main arm64 Kconfig and remove
the additional CONFIG_AS_LSE definition and check.
Cc: Will Deacon <will@kernel.org>
Reviewed-by: Vladimir Murzin <vladimir.murzin@arm.com>
Tested-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
Similar to 'cc-option' or 'ld-option', it is occasionally necessary to
check whether the assembler supports certain ISA extensions. In the
arm64 code we currently do this in Makefile with an additional define:
lseinstr := $(call as-instr,.arch_extension lse,-DCONFIG_AS_LSE=1)
Add the 'as-instr' option so that it can be used in Kconfig directly:
def_bool $(as-instr,.arch_extension lse)
Acked-by: Masahiro Yamada <masahiroy@kernel.org>
Reviewed-by: Vladimir Murzin <vladimir.murzin@arm.com>
Tested-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
This driver allocates a dynamic cpu hotplug state but never releases it.
If reloaded in a loop it will quickly trigger a WARN message:
"No more dynamic states available for CPU hotplug"
Fix by calling cpuhp_remove_multi_state on remove like several other
perf pmu drivers.
Also fix the cleanup logic on probe error paths: add the missing
cpuhp_remove_multi_state call and properly check the return value from
cpuhp_state_add_instant_nocalls.
Fixes: 9a66d36cc7 ("drivers/perf: imx_ddr: Add DDR performance counter support to perf")
Acked-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Will Deacon <will@kernel.org>
Nikolay Aleksandrov says:
====================
net: bridge: add vlan notifications and rtm support
This patch-set is a prerequisite for adding per-vlan options support
because we need to be able to send vlan-only notifications and do larger
vlan netlink dumps. Per-vlan options are needed as we move the control
more to vlans and would like to add per-vlan state (needed for per-vlan
STP and EVPN), per-vlan multicast options and control, and I'm sure
there would be many more per-vlan options coming.
Now we create/delete/dump vlans with the device AF_SPEC attribute which is
fine since we support vlan ranges or use a compact bridge_vlan_info
structure, but that cannot really be extended to support per-vlan options
well. The biggest issue is dumping them - we tried using the af_spec with
a new vlan option attribute but that led to insufficient message size
quickly, also another minor problem with that is we have to dump all vlans
always when notifying which, with options present, can be huge if they have
different options set, so we decided to add new rtm message types
specifically for vlans and register handlers for them and a new bridge vlan
notification nl group for vlan-only notifications.
The new RTM NEW/DEL/GETVLAN types introduced match the current af spec
bridge functionality and in fact use the same helpers.
The new nl format is:
[BRIDGE_VLANDB_ENTRY]
[BRIDGE_VLANDB_ENTRY_INFO] - bridge_vlan_info (either 1 vlan or
range start)
[BRIDGE_VLANDB_ENTRY_RANGE] - range end
This allows to encapsulate a range in a single attribute and also to
create vlans and immediately set options on all of them with a single
attribute. The GETVLAN dump can span multiple messages and dump all the
necessary information. The vlan-only notifications are sent on
NEW/DELVLAN events or when vlan options change (currently only flags),
we try hard to compress the vlans into ranges in the notifications as
well. When the per-vlan options are added we'll add helpers to check for
option equality between neighbor vlans and will keep compressing them
when possible.
Note patch 02 is not really required, it's just a nice addition to have
human-readable error messages from the different vlan checks.
iproute2 changes and selftests will be sent with the next set which adds
the first per-vlan option - per-vlan state similar to the port state.
v2: changed patch 03 and patch 04 to use nlmsg_parse() in order to
strictly validate the msg and make sure there are no remaining bytes
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we can notify, send a notification on add/del or change of flags.
Notifications are also compressed when possible to reduce their number
and relieve user-space of extra processing, due to that we have to
manually notify after each add/del in order to avoid double
notifications. We try hard to notify only about the vlans which actually
changed, thus a single command can result in multiple notifications
about disjoint ranges if there were vlans which didn't change inside.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new rtnetlink group for bridge vlan notifications - RTNLGRP_BRVLAN
and add support for sending vlan notifications (both single and ranges).
No functional changes intended, the notification support will be used by
later patches.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new vlandb nl attribute - BRIDGE_VLANDB_ENTRY_RANGE which causes
RTM_NEWVLAN/DELVAN to act on a range. Dumps now automatically compress
similar vlans into ranges. This will be also used when per-vlan options
are introduced and vlans' options match, they will be put into a single
range which is encapsulated in one netlink attribute. We need to run
similar checks as br_process_vlan_info() does because these ranges will
be used for options setting and they'll be able to skip
br_process_vlan_info().
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding RTM_DELVLAN support similar to RTM_NEWVLAN is simple, just need to
map DELVLAN to DELLINK and register the handler.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add initial RTM_NEWVLAN support which can only create vlans, operating
similar to the current br_afspec(). We will use it later to also change
per-vlan options. Old-style (flag-based) vlan ranges are not allowed
when using RTM messages, we will introduce vlan ranges later via a new
nested attribute which would allow us to have all the information about a
range encapsulated into a single nl attribute.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds vlan rtm definitions:
- NEWVLAN: to be used for creating vlans, setting options and
notifications
- DELVLAN: to be used for deleting vlans
- GETVLAN: used for dumping vlan information
Dumping vlans which can span multiple messages is added now with basic
information (vid and flags). We use nlmsg_parse() to validate the header
length in order to be able to extend the message with filtering
attributes later.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add extack messages on vlan processing errors. We need to move the flags
missing check after the "last" check since we may have "last" set but
lack a range end flag in the next entry.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add helpers to check if a vlan id or range are valid. The range helper
must be called when range start or end are detected.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It should remove the align-padding before @name.
[yes, there's a "hole" in the structure now, but that's fine, no one
cares. If they do care, the whole thing should be restructured using
pahole to find a better ordering. Removing this field is good as some
drivers have been known to abuse it for other things when they shouldn't
have been doing that. -- gregkh]
Signed-off-by: Dmitry Safonov <dima@arista.com>
Link: https://lore.kernel.org/r/20200114171912.261787-4-dima@arista.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes a regression on setting up asynchronous commands to use
external trigger sources when board-specific routing information is
missing.
`ni_find_device_routes()` (called via `ni_assign_device_routes()`) finds
the table of register values for the device family and the set of valid
routes for the specific board. If both are found,
`tables->route_values` is set to point to the table of register values
for the device family and `tables->valid_routes` is set to point to the
list of valid routes for the specific board. If either is not found,
both `tables->route_values` and `tables->valid_routes` are left set at
their initial null values (initialized by `ni_assign_device_routes()`)
and the function returns `-ENODATA`.
Returning an error results in some routing functionality being disabled.
Unfortunately, leaving `table->route_values` set to `NULL` also breaks
the setting up of asynchronous commands that are configured to use
external trigger sources. Calls to `ni_check_trigger_arg()` or
`ni_check_trigger_arg_roffs()` while checking the asynchronous command
set-up would result in a null pointer dereference if
`table->route_values` is `NULL`. The null pointer dereference is fixed
in another patch, but it now results in failure to set up the
asynchronous command. That is a regression from the behavior prior to
commit 347e244884 ("staging: comedi: tio: implement global tio/ctr
routing") and commit 56d0b826d3 ("staging: comedi: ni_mio_common:
implement new routing for TRIG_EXT").
Change `ni_find_device_routes()` to set `tables->route_values` and/or
`tables->valid_routes` to valid information even if the other one can
only be set to `NULL` due to missing information. The function will
still return an error in that case. This should result in
`tables->valid_routes` being valid for all currently supported device
families even if the board-specific routing information is missing.
That should be enough to fix the regression on setting up asynchronous
commands to use external triggers for boards with missing routing
information.
Fixes: 347e244884 ("staging: comedi: tio: implement global tio/ctr routing")
Fixes: 56d0b826d3 ("staging: comedi: ni_mio_common: implement new routing for TRIG_EXT").
Cc: <stable@vger.kernel.org> # 4.20+
Cc: Spencer E. Olson <olsonse@umich.edu>
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Link: https://lore.kernel.org/r/20200114182532.132058-3-abbotti@mev.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In `ni_find_route_source()`, `tables->route_values` gets dereferenced.
However it is possible that `tables->route_values` is `NULL`, leading to
a null pointer dereference. `tables->route_values` will be `NULL` if
the call to `ni_assign_device_routes()` during board initialization
returned an error due to missing device family routing information or
missing board-specific routing information. For example, there is
currently no board-specific routing information provided for the
PCIe-6251 board and several other boards, so those are affected by this
bug.
The bug is triggered when `ni_find_route_source()` is called via
`ni_check_trigger_arg()` or `ni_check_trigger_arg_roffs()` when checking
the arguments for setting up asynchronous commands. Fix it by returning
`-EINVAL` if `tables->route_values` is `NULL`.
Even with this fix, setting up asynchronous commands to use external
trigger sources for boards with missing routing information will still
fail gracefully. Since `ni_find_route_source()` only depends on the
device family routing information, it would be better if that was made
available even if the board-specific routing information is missing.
That will be addressed by another patch.
Fixes: 4bb90c87ab ("staging: comedi: add interface to ni routing table information")
Cc: <stable@vger.kernel.org> # 4.20+
Cc: Spencer E. Olson <olsonse@umich.edu>
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Link: https://lore.kernel.org/r/20200114182532.132058-2-abbotti@mev.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't print an error message about VMX being disabled by BIOS if KVM,
the sole user of VMX, is disabled. E.g. if KVM is disabled and the MSR
is unlocked, the kernel will intentionally disable VMX when locking
feature control and then complain that "BIOS" disabled VMX.
Fixes: ef4d3bf198 ("x86/cpu: Clear VMX feature flag if VMX is not fully enabled")
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lkml.kernel.org/r/20200114202545.20296-1-sean.j.christopherson@intel.com
Ido Schimmel says:
====================
mlxsw: Various fixes
This patch set contains various fixes for mlxsw.
Patch #1 splits the init() callback between Spectrum-2 and Spectrum-3 in
order to avoid enforcing the same firmware version for both ASICs, as
this can't possibly work. Without this patch the driver cannot boot with
the Spectrum-3 ASIC.
Patches #2-#3 fix a long standing race condition that was recently
exposed while testing the driver on an emulator, which is very slow
compared to the actual hardware. The problem is explained in detail in
the commit messages.
Patch #4 fixes a selftest.
Patch #5 prevents offloaded qdiscs from presenting a non-zero backlog to
the user when the netdev is down. This is done by clearing the cached
backlog in the driver when the netdev goes down.
Patch #6 fixes qdisc statistics (backlog and tail drops) to also take
into account the multicast traffic classes.
v2:
* Patches #2-#3: use skb_cow_head() instead of skb_unshare() as
suggested by Jakub. Remove unnecessary check regarding headroom
* Patches #5-#6: new
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
mlxsw configures Spectrum in such a way that BUM traffic is passed not
through its nominal traffic class TC, but through its MC counterpart TC+8.
However, when collecting statistics, Qdiscs only look at the nominal TC and
ignore the MC TC.
Add two helpers to compute the value for logical TC from the constituents,
one for backlog, the other for tail drops. Use them throughout instead of
going through the xstats pointer directly.
Counters for TX bytes and packets are deduced from packet priority
counters, and therefore already include BUM traffic. wred_drop counter is
irrelevant on MC TCs, because RED is not enabled on them.
Fixes: 7b81953066 ("mlxsw: spectrum: Configure MC-aware mode on mlxsw ports")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Per-port counter cache used by Qdiscs is updated periodically, unless the
port is down. The fact that the cache is not updated for down ports is no
problem for most counters, which are relative in nature. However, backlog
is absolute in nature, and if there is a non-zero value in the cache around
the time that the port goes down, that value just stays there. This value
then leaks to offloaded Qdiscs that report non-zero backlog even if
there (obviously) is no traffic.
The HW does not keep backlog of a downed port, so do likewise: as the port
goes down, wipe the backlog value from xstats.
Fixes: 075ab8adaf ("mlxsw: spectrum: Collect tclass related stats periodically")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mausezahn does not recognize "own" as a keyword on source IP address. As a
result, the MC stream is not running at all, and therefore no UC
degradation can be observed even in principle.
Fix the invocation, and tighten the test: due to the minimum shaper
configured at the MC TCs, we always expect about 20% degradation. Fail the
test if it is lower.
Fixes: 573363a68f ("selftests: mlxsw: Add qos_lib.sh")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reported-by: Amit Cohen <amitc@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver needs to prepend a Tx header to each packet it is
transmitting. The header includes information such as the egress port
and traffic class.
The addition of the header requires the driver to modify the SKB's
header and therefore it must not be shared. Otherwise, we risk hitting
various race conditions.
For example, when a packet is flooded (cloned) by the bridge driver to
two switch ports swp1 and swp2:
t0 - mlxsw_sp_port_xmit() is called for swp1. Tx header is prepended with
swp1's port number
t1 - mlxsw_sp_port_xmit() is called for swp2. Tx header is prepended with
swp2's port number, overwriting swp1's port number
t2 - The device processes data buffer from t0. Packet is transmitted via
swp2
t3 - The device processes data buffer from t1. Packet is transmitted via
swp2
Usually, the device is fast enough and transmits the packet before its
Tx header is overwritten, but this is not the case in emulated
environments.
Fix this by making sure the SKB's header is writable by calling
skb_cow_head(). Since the function ensures we have headroom to push the
Tx header, the check further in the function can be removed.
v2:
* Use skb_cow_head() instead of skb_unshare() as suggested by Jakub
* Remove unnecessary check regarding headroom
Fixes: 31557f0f97 ("mlxsw: Introduce Mellanox SwitchX-2 ASIC support")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Shalom Toledo <shalomt@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver needs to prepend a Tx header to each packet it is
transmitting. The header includes information such as the egress port
and traffic class.
The addition of the header requires the driver to modify the SKB's
header and therefore it must not be shared. Otherwise, we risk hitting
various race conditions.
For example, when a packet is flooded (cloned) by the bridge driver to
two switch ports swp1 and swp2:
t0 - mlxsw_sp_port_xmit() is called for swp1. Tx header is prepended with
swp1's port number
t1 - mlxsw_sp_port_xmit() is called for swp2. Tx header is prepended with
swp2's port number, overwriting swp1's port number
t2 - The device processes data buffer from t0. Packet is transmitted via
swp2
t3 - The device processes data buffer from t1. Packet is transmitted via
swp2
Usually, the device is fast enough and transmits the packet before its
Tx header is overwritten, but this is not the case in emulated
environments.
Fix this by making sure the SKB's header is writable by calling
skb_cow_head(). Since the function ensures we have headroom to push the
Tx header, the check further in the function can be removed.
v2:
* Use skb_cow_head() instead of skb_unshare() as suggested by Jakub
* Remove unnecessary check regarding headroom
Fixes: 56ade8fe3f ("mlxsw: spectrum: Add initial support for Spectrum ASIC")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Shalom Toledo <shalomt@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit a72afb6879 ("mlxsw: Enforce firmware version for
Spectrum-2") I added a required firmware version for Spectrum-2, but
missed the fact that mlxsw_sp2_init() is used by both Spectrum-2 and
Spectrum-3. This means that the same firmware version will be used for
both, which is wrong.
Fix this by creating a new init() callback for Spectrum-3.
Fixes: a72afb6879 ("mlxsw: Enforce firmware version for Spectrum-2")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Tested-by: Shalom Toledo <shalomt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
