If support wide temperature, it necessary to set voltage to low temperature
voltage before system suspend, so that it can resume successfully at low
temperature.
Change-Id: Ie6787092c9510788054217bd830b5ae1e4dd6bc2
Signed-off-by: Finley Xiao <finley.xiao@rock-chips.com>
The ATF must contain the following commit:
cd61876e275e ("plat: rk3399: ddr: add support adjust noc read latency")
Change-Id: I322f8c9d454fb1234b042438c85521275ceda4bc
Signed-off-by: Finley Xiao <finley.xiao@rock-chips.com>
This patch adds support to calculate the static power in milliwatts
consumed by devices.
Change-Id: Ied4ba5adecea45ff34b372a6e23c70882000aef3
Signed-off-by: Finley Xiao <finley.xiao@rock-chips.com>
Add a couple of new APIs to check the probing status of qman and bman:
'int bman_is_probed()' and 'int qman_is_probed()'.
They return the following values.
* 1 if qman/bman were probed correctly
* 0 if qman/bman were not yet probed
* -1 if probing of qman/bman failed
Drivers that use qman/bman driver services are required to use these
APIs before calling any functions exported by qman or bman drivers
or otherwise they will crash the kernel.
The APIs will be used in the following couple of qbman portal patches
and later in the series in the dpaa1 ethernet driver.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
* linux-linaro-lsk-v4.4: (519 commits)
Linux 4.4.154
cdrom: Fix info leak/OOB read in cdrom_ioctl_drive_status
iscsi target: fix session creation failure handling
scsi: core: Avoid that SCSI device removal through sysfs triggers a deadlock
scsi: sysfs: Introduce sysfs_{un,}break_active_protection()
MIPS: lib: Provide MIPS64r6 __multi3() for GCC < 7
MIPS: Correct the 64-bit DSP accumulator register size
kprobes: Make list and blacklist root user read only
s390/pci: fix out of bounds access during irq setup
s390/qdio: reset old sbal_state flags
s390: fix br_r1_trampoline for machines without exrl
x86/spectre: Add missing family 6 check to microcode check
x86/irqflags: Mark native_restore_fl extern inline
pinctrl: freescale: off by one in imx1_pinconf_group_dbg_show()
ASoC: sirf: Fix potential NULL pointer dereference
ASoC: dpcm: don't merge format from invalid codec dai
udl-kms: fix crash due to uninitialized memory
udl-kms: handle allocation failure
udl-kms: change down_interruptible to down
fuse: Add missed unlock_page() to fuse_readpages_fill()
...
Conflicts:
Makefile
arch/arm64/mm/init.c
fs/squashfs/block.c
include/uapi/linux/prctl.h
kernel/sys.c
Change-Id: Ie03b5adfbbb4ab2bf16bc55d99f0d8a9c540a53b
[ Upstream commit 1c74d5c0de ]
Currently we are enabling handling of interrupts specific to Tegra124+
which happen to overlap with previous generations. Let's specify
interrupts mask per SoC generation for consistency and in a preparation
of squashing of Tegra20 driver into the common one that will enable
handling of GART faults which may be undesirable by newer generations.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Various updates to soc/fsl for 4.19
Moves DPAA2 DPIO driver from staging to fsl/soc
Adds multiple-pin support to QE gpio driver
* tag 'soc-fsl-for-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/leo/linux:
soc: fsl: cleanup Kconfig menu
soc: fsl: dpio: Convert DPIO documentation to .rst
staging: fsl-mc: Remove remaining files
staging: fsl-mc: Move DPIO from staging to drivers/soc/fsl
staging: fsl-dpaa2: eth: move generic FD defines to DPIO
soc: fsl: qe: gpio: Add qe_gpio_set_multiple
Signed-off-by: Olof Johansson <olof@lixom.net>
Move the NXP DPIO (Datapath I/O Driver) out of the
drivers/staging directory and into the drivers/soc/fsl directory.
The DPIO driver enables access to Queue and Buffer Manager (QBMAN)
hardware on NXP DPAA2 devices. This is a prerequisite to moving the
DPAA2 Ethernet driver out of staging.
Signed-off-by: Roy Pledge <roy.pledge@nxp.com>
Reviewed-by: Horia Geantă <horia.geanta@nxp.com>
Reviewed-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Platform drivers need make a lot of resource state requests at the same
time, say, at the start or end of an usecase. It can be quite
inefficient to send each request separately. Instead they can give the
RPMH library a batch of requests to be sent and wait on the whole
transaction to be complete.
rpmh_write_batch() is a blocking call that can be used to send multiple
RPMH command sets. Each RPMH command set is set asynchronously and the
API blocks until all the command sets are complete and receive their
tx_done callbacks.
Signed-off-by: Lina Iyer <ilina@codeaurora.org>
Signed-off-by: Raju P.L.S.S.S.N <rplsssn@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Platform drivers that want to send a request but do not want to block
until the RPMH request completes have now a new API -
rpmh_write_async().
The API allocates memory and send the requests and returns the control
back to the platform driver. The tx_done callback from the controller is
handled in the context of the controller's thread and frees the
allocated memory. This API allows RPMH requests from atomic contexts as
well.
Signed-off-by: Lina Iyer <ilina@codeaurora.org>
Signed-off-by: Raju P.L.S.S.S.N <rplsssn@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Active state requests are sent immediately to the RSC controller, while
sleep and wake state requests are cached in this driver to avoid taxing
the RSC controller repeatedly. The cached values will be sent to the
controller when the rpmh_flush() is called.
Generally, flushing is a system PM activity and may be called from the
system PM drivers when the system is entering suspend or deeper sleep
modes during cpuidle.
Also allow invalidating the cached requests, so they may be re-populated
again.
Signed-off-by: Lina Iyer <ilina@codeaurora.org>
[rplsssn: remove unneeded semicolon, address line over 80chars error]
Signed-off-by: Raju P.L.S.S.S.N <rplsssn@codeaurora.org>
Reviewed-by: Evan Green <evgreen@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Sending RPMH requests and waiting for response from the controller
through a callback is common functionality across all platform drivers.
To simplify drivers, add a library functions to create RPMH client and
send resource state requests.
rpmh_write() is a synchronous blocking call that can be used to send
active state requests.
Signed-off-by: Lina Iyer <ilina@codeaurora.org>
Signed-off-by: Raju P.L.S.S.S.N <rplsssn@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add controller driver for QCOM SoCs that have hardware based shared
resource management. The hardware IP known as RSC (Resource State
Coordinator) houses multiple Direct Resource Voter (DRV) for different
execution levels. A DRV is a unique voter on the state of a shared
resource. A Trigger Control Set (TCS) is a bunch of slots that can house
multiple resource state requests, that when triggered will issue those
requests through an internal bus to the Resource Power Manager Hardened
(RPMH) blocks. These hardware blocks are capable of adjusting clocks,
voltages, etc. The resource state request from a DRV are aggregated
along with state requests from other processors in the SoC and the
aggregate value is applied on the resource.
Some important aspects of the RPMH communication -
- Requests are <addr, value> with some header information
- Multiple requests (upto 16) may be sent through a TCS, at a time
- Requests in a TCS are sent in sequence
- Requests may be fire-n-forget or completion (response expected)
- Multiple TCS from the same DRV may be triggered simultaneously
- Cannot send a request if another request for the same addr is in
progress from the same DRV
- When all the requests from a TCS are complete, an IRQ is raised
- The IRQ handler needs to clear the TCS before it is available for
reuse
- TCS configuration is specific to a DRV
- Platform drivers may use DRV from different RSCs to make requests
Resource state requests made when CPUs are active are called 'active'
state requests. Requests made when all the CPUs are powered down (idle
state) are called 'sleep' state requests. They are matched by a
corresponding 'wake' state requests which puts the resources back in to
previously requested active state before resuming any CPU. TCSes are
dedicated for each type of requests. Active mode TCSes (AMC) are used to
send requests immediately to the resource, while control TCS are used to
provide specific information to the controller. Sleep and Wake TCS send
sleep and wake requests, after and before the system halt respectively.
Signed-off-by: Lina Iyer <ilina@codeaurora.org>
Signed-off-by: Raju P.L.S.S.S.N <rplsssn@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add a basic wide-temperature control model for device to adjust opp
table and max frequency.
Change-Id: I23f29ac1892093c527e730164eba086f02667de3
Signed-off-by: Finley Xiao <finley.xiao@rock-chips.com>
Recent Raspberry Pi firmware provides a mailbox property to detect
under-voltage conditions. Here is the current definition.
The u32 value returned by the firmware is divided into 2 parts:
- lower 16-bits are the live value
- upper 16-bits are the history or sticky value
Bits:
0: undervoltage
1: arm frequency capped
2: currently throttled
16: undervoltage has occurred
17: arm frequency capped has occurred
18: throttling has occurred
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Eric Anholt <eric@anholt.net>
Pull ARM SoC late updates from Olof Johansson:
"This is a branch with a few merge requests that either came in late,
or took a while longer for us to review and merge than usual and thus
cut it a bit close to the merge window. We stage them in a separate
branch and if things look good, we still send them up -- and that's
the case here.
This is mostly DT additions for Renesas platforms, adding IP block
descriptions for existing and new SoCs.
There are also some driver updates for Qualcomm platforms for SMEM/QMI
and GENI, which is their generalized serial protocol interface"
* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (186 commits)
soc: qcom: smem: introduce qcom_smem_virt_to_phys()
soc: qcom: qmi: fix a buffer sizing bug
MAINTAINERS: Update pattern for qcom_scm
soc: Unconditionally include qcom Makefile
soc: qcom: smem: check sooner in qcom_smem_set_global_partition()
soc: qcom: smem: fix qcom_smem_set_global_partition()
soc: qcom: smem: fix off-by-one error in qcom_smem_alloc_private()
soc: qcom: smem: byte swap values properly
soc: qcom: smem: return proper type for cached entry functions
soc: qcom: smem: fix first cache entry calculation
soc: qcom: cmd-db: Make endian-agnostic
drivers: qcom: add command DB driver
arm64: dts: renesas: salvator-common: Add ADV7482 support
ARM: dts: r8a7740: Add CEU1
ARM: dts: r8a7740: Add CEU0
arm64: dts: renesas: salvator-common: enable VIN
arm64: dts: renesas: r8a77970: add VIN and CSI-2 nodes
arm64: dts: renesas: r8a77965: add VIN and CSI-2 nodes
arm64: dts: renesas: r8a7796: add VIN and CSI-2 nodes
arm64: dts: renesas: r8a7795-es1: add CSI-2 node
...
The tegra_cpuidle_pcie_irqs_in_use() function is stubbed out for non-ARM
builds, but now we can compile-test the Tegra pci driver on non-Tegra
ARM platforms as well, which results in a new link error:
drivers/pci/host/pci-tegra.o: In function `tegra_pcie_map_irq':
pci-tegra.c:(.text+0x288): undefined reference to `tegra_cpuidle_pcie_irqs_in_use'
drivers/pci/host/pci-tegra.o: In function `tegra_msi_map':
pci-tegra.c:(.text+0xba0): undefined reference to `tegra_cpuidle_pcie_irqs_in_use'
This adapts the #ifdef statement to match the exact condition under which
the function can be called.
Fixes: 51bc085d64 ("PCI: Improve host drivers compile test coverage")
Cc: Rob Herring <robh@kernel.org>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Command DB is a simple database in the shared memory of QCOM SoCs, that
provides information regarding shared resources. Some shared resources
in the SoC have properties that are probed dynamically at boot by the
remote processor. The information pertaining to the SoC and the platform
are made available in the shared memory. Drivers can query this
information using predefined strings.
Signed-off-by: Mahesh Sivasubramanian <msivasub@codeaurora.org>
Signed-off-by: Lina Iyer <ilina@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
memory: tegra: Changes for v4.18-rc1
This contains some cleanup of the memory controller driver as well as
unification work to share more code between Tegra20 and later SoC
generations. Also included are an implementation for the hot resets
functionality by the memory controller which is required to properly
reset busy hardware.
* tag 'tegra-for-4.18-memory-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
dt-bindings: memory: tegra: Remove Tegra114 SATA and AFI reset definitions
memory: tegra: Remove Tegra114 SATA and AFI reset definitions
memory: tegra: Register SMMU after MC driver became ready
memory: tegra: Add Tegra210 memory controller hot resets
memory: tegra: Add Tegra124 memory controller hot resets
memory: tegra: Add Tegra114 memory controller hot resets
memory: tegra: Add Tegra30 memory controller hot resets
memory: tegra: Add Tegra20 memory controller hot resets
memory: tegra: Introduce memory client hot reset
memory: tegra: Squash tegra20-mc into common tegra-mc driver
memory: tegra: Remove unused headers inclusions
memory: tegra: Apply interrupts mask per SoC
memory: tegra: Setup interrupts mask before requesting IRQ
memory: tegra: Do not handle spurious interrupts
dt-bindings: memory: tegra: Add hot resets definitions
Signed-off-by: Olof Johansson <olof@lixom.net>
When change vop status and ddr frequency at the same time,
the following deadlock will happen:
vop no/off dmcfreq
vop_crtc_disable update_devfreq
->mutex_lock(&vop->vop_lock); ->mutex_lock(&pd->pmu->mutex);
->pm_runtime_put(vop->dev); ->mutex_lock(&vop->vop_lock);
->mutex_lock(&pd->pmu->mutex); ...
Use new dmcfreq rwsem to decouple vop and pd driver, and get better
parallelism.
Change-Id: I56a4ee944200826d2a09e3ae8d2f4837f6f769d6
Signed-off-by: Finley Xiao <finley.xiao@rock-chips.com>
Signed-off-by: Tao Huang <huangtao@rock-chips.com>
Move rockchip_dmcfreq_vop_bandwidth_request and
rockchip_dmcfreq_vop_bandwidth_update from rockchip_drm_fb.h
to rockchip_dmc.h.
Change-Id: I5b023e44b46a6c613af71452a940d31feb9b2d97
Signed-off-by: Tao Huang <huangtao@rock-chips.com>
remove rockchip_pm_register_notify_to_dmc from rockchip_dmc.h
Change-Id: I9e78eaec2a88cfc06ac3d24f01870cd39c9d05ad
Signed-off-by: Tao Huang <huangtao@rock-chips.com>
