Changes in 4.19.50
ethtool: fix potential userspace buffer overflow
Fix memory leak in sctp_process_init
ipv4: not do cache for local delivery if bc_forwarding is enabled
ipv6: fix the check before getting the cookie in rt6_get_cookie
neighbor: Call __ipv4_neigh_lookup_noref in neigh_xmit
net: ethernet: ti: cpsw_ethtool: fix ethtool ring param set
net/mlx4_en: ethtool, Remove unsupported SFP EEPROM high pages query
net: mvpp2: Use strscpy to handle stat strings
net: rds: fix memory leak in rds_ib_flush_mr_pool
net: sfp: read eeprom in maximum 16 byte increments
net/tls: replace the sleeping lock around RX resync with a bit lock
packet: unconditionally free po->rollover
pktgen: do not sleep with the thread lock held.
Revert "fib_rules: return 0 directly if an exactly same rule exists when NLM_F_EXCL not supplied"
ipv6: use READ_ONCE() for inet->hdrincl as in ipv4
ipv6: fix EFAULT on sendto with icmpv6 and hdrincl
mtd: spinand: macronix: Fix ECC Status Read
rcu: locking and unlocking need to always be at least barriers
parisc: Use implicit space register selection for loading the coherence index of I/O pdirs
NFSv4.1: Again fix a race where CB_NOTIFY_LOCK fails to wake a waiter
NFSv4.1: Fix bug only first CB_NOTIFY_LOCK is handled
fuse: fallocate: fix return with locked inode
pstore: Remove needless lock during console writes
pstore: Convert buf_lock to semaphore
pstore: Set tfm to NULL on free_buf_for_compression
pstore/ram: Run without kernel crash dump region
x86/power: Fix 'nosmt' vs hibernation triple fault during resume
x86/insn-eval: Fix use-after-free access to LDT entry
i2c: xiic: Add max_read_len quirk
s390/mm: fix address space detection in exception handling
xen-blkfront: switch kcalloc to kvcalloc for large array allocation
MIPS: Bounds check virt_addr_valid
MIPS: pistachio: Build uImage.gz by default
Revert "MIPS: perf: ath79: Fix perfcount IRQ assignment"
genwqe: Prevent an integer overflow in the ioctl
test_firmware: Use correct snprintf() limit
drm/gma500/cdv: Check vbt config bits when detecting lvds panels
drm/msm: fix fb references in async update
drm: add non-desktop quirk for Valve HMDs
drm/nouveau: add kconfig option to turn off nouveau legacy contexts. (v3)
drm: add non-desktop quirks to Sensics and OSVR headsets.
drm/amdgpu/psp: move psp version specific function pointers to early_init
drm/radeon: prefer lower reference dividers
drm/amdgpu: remove ATPX_DGPU_REQ_POWER_FOR_DISPLAYS check when hotplug-in
drm/i915: Fix I915_EXEC_RING_MASK
drm/i915/fbc: disable framebuffer compression on GeminiLake
drm/i915: Maintain consistent documentation subsection ordering
drm: don't block fb changes for async plane updates
drm/i915/gvt: Initialize intel_gvt_gtt_entry in stack
TTY: serial_core, add ->install
ipv4: Define __ipv4_neigh_lookup_noref when CONFIG_INET is disabled
ethtool: check the return value of get_regs_len
Linux 4.19.50
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
commit ec527c3180 upstream.
As explained in
0cc3cd2165 ("cpu/hotplug: Boot HT siblings at least once")
we always, no matter what, have to bring up x86 HT siblings during boot at
least once in order to avoid first MCE bringing the system to its knees.
That means that whenever 'nosmt' is supplied on the kernel command-line,
all the HT siblings are as a result sitting in mwait or cpudile after
going through the online-offline cycle at least once.
This causes a serious issue though when a kernel, which saw 'nosmt' on its
commandline, is going to perform resume from hibernation: if the resume
from the hibernated image is successful, cr3 is flipped in order to point
to the address space of the kernel that is being resumed, which in turn
means that all the HT siblings are all of a sudden mwaiting on address
which is no longer valid.
That results in triple fault shortly after cr3 is switched, and machine
reboots.
Fix this by always waking up all the SMT siblings before initiating the
'restore from hibernation' process; this guarantees that all the HT
siblings will be properly carried over to the resumed kernel waiting in
resume_play_dead(), and acted upon accordingly afterwards, based on the
target kernel configuration.
Symmetricaly, the resumed kernel has to push the SMT siblings to mwait
again in case it has SMT disabled; this means it has to online all
the siblings when resuming (so that they come out of hlt) and offline
them again to let them reach mwait.
Cc: 4.19+ <stable@vger.kernel.org> # v4.19+
Debugged-by: Thomas Gleixner <tglx@linutronix.de>
Fixes: 0cc3cd2165 ("cpu/hotplug: Boot HT siblings at least once")
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Acked-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The recently introduced Energy Model (EM) framework manages power cost
tables of CPUs. These tables are currently only visible from kernel
space. However, in order to debug the behaviour of subsystems that use
the EM (EAS for example), it is often required to know what the power
costs are from userspace.
For this reason, introduce under /sys/kernel/debug/energy_model a set of
directories representing the performance domains of the system. Each
performance domain contains a set of sub-directories representing the
different capacity states (cs) and their attributes, as well as a file
exposing the related CPUs.
The resulting hierarchy is as follows on Arm juno r0 for example:
/sys/kernel/debug/energy_model
├── pd0
│ ├── cpus
│ ├── cs:450000
│ │ ├── cost
│ │ ├── frequency
│ │ └── power
│ ├── cs:575000
│ │ ├── cost
│ │ ├── frequency
│ │ └── power
│ ├── cs:700000
│ │ ├── cost
│ │ ├── frequency
│ │ └── power
│ ├── cs:775000
│ │ ├── cost
│ │ ├── frequency
│ │ └── power
│ └── cs:850000
│ ├── cost
│ ├── frequency
│ └── power
└── pd1
├── cpus
├── cs:1100000
│ ├── cost
│ ├── frequency
│ └── power
├── cs:450000
│ ├── cost
│ ├── frequency
│ └── power
├── cs:625000
│ ├── cost
│ ├── frequency
│ └── power
├── cs:800000
│ ├── cost
│ ├── frequency
│ └── power
└── cs:950000
├── cost
├── frequency
└── power
Bug: 120440300
Change-Id: I4098c3d3e07fc4a14514751ac881422131b759e9
Signed-off-by: Quentin Perret <quentin.perret@arm.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
(cherry picked from commit 9cac42d064
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm.git bleeding-edge)
Signed-off-by: Quentin Perret <quentin.perret@arm.com>
This reverts commit b8c80a0f42. It has not
been accepted upstream and is useful only for debug purpose. An
alternate debugfs interface will be pushed upstream to expose the Energy
Model. Android should use that too. In the meantime, it should be early
enough to remove the sysfs nodes before partners start basing userspace
tools on them.
Bug: 120440300
Change-Id: I8a5f003550df7df9116d4735c8d9ac10ac0aa79c
Signed-off-by: Quentin Perret <quentin.perret@arm.com>
Add API log_wakeup_reason() and expose it to userspace via sysfs path
/sys/kernel/wakeup_reasons/last_resume_reason
Bug: 120445600
Signed-off-by: Ruchi Kandoi <kandoiruchi@google.com>
[AmitP: Folded following android-4.9 commit changes into this patch
1135122a19 ("ANDROID: POWER: fix compile warnings in log_wakeup_reason")
b4e6247778 ("ANDROID: Power: Changes the permission to read only for sysfs file /sys/kernel/wakeup_reasons/last_resume_reason")
e13dbc7c69 ("ANDROID: power: wakeup_reason: rename irq_count to irqcount")]
Signed-off-by: Amit Pundir <amit.pundir@linaro.org>
[astrachan: Folded the following changes into this patch:
39d7c7fe91c0 ("ANDROID: power: wakeup_reason: Add guard condition for maximum wakeup reasons")
0730434bdf49 ("ANDROID: power: wakeup_reason: Avoids bogus error messages for the suspend aborts.")
4e42dceae54e ("ANDROID: power: wakeup_reason: Adds functionality to log the last suspend abort reason.")
f21313b70ac7 ("ANDROID: power: wakeup_reason: Report suspend times from last_suspend_time")
f97ec34442ac ("ANDROID: power: wakeup_reason: fix suspend time reporting")
cd92df73e504 ("ANDROID: power: wakeup: Add last wake up source logging for suspend abort reason.")
546b6ae3c087 ("ANDROID: power: wakeup: Add the guard condition for len in pm_get_active_wakeup_sources")
1453d9ffcdbe ("ANDROID: power: wakeup_reason: make logging work in an interrupt context.")]
Change-Id: I81addaf420f1338255c5d0638b0d244a99d777d1
Signed-off-by: Alistair Strachan <astrachan@google.com>
Expose the Energy Model (read-only) of all performance domains in sysfs
for convenience. To do so, add a kobject to the CPU subsystem under the
umbrella of which a kobject for each performance domain is attached.
The resulting hierarchy is as follows for a platform with two
performance domains for example:
/sys/devices/system/cpu/energy_model
├── pd0
│ ├── cost
│ ├── cpus
│ ├── frequency
│ └── power
└── pd4
├── cost
├── cpus
├── frequency
└── power
In this implementation, the kobject abstraction is only used as a
convenient way of exposing data to sysfs. However, it could also be
used in the future to allocate and release performance domains in a more
dynamic way using reference counting.
Change-Id: Ia98bcae21c3578e385be9c6b030c9adff8210909
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Signed-off-by: Quentin Perret <quentin.perret@arm.com>
Message-Id: <20181016101513.26919-5-quentin.perret@arm.com>
Signed-off-by: Quentin Perret <quentin.perret@arm.com>
Several subsystems in the kernel (task scheduler and/or thermal at the
time of writing) can benefit from knowing about the energy consumed by
CPUs. Yet, this information can come from different sources (DT or
firmware for example), in different formats, hence making it hard to
exploit without a standard API.
As an attempt to address this, introduce a centralized Energy Model
(EM) management framework which aggregates the power values provided
by drivers into a table for each performance domain in the system. The
power cost tables are made available to interested clients (e.g. task
scheduler or thermal) via platform-agnostic APIs. The overall design
is represented by the diagram below (focused on Arm-related drivers as
an example, but applicable to any architecture):
+---------------+ +-----------------+ +-------------+
| Thermal (IPA) | | Scheduler (EAS) | | Other |
+---------------+ +-----------------+ +-------------+
| | em_pd_energy() |
| | em_cpu_get() |
+-----------+ | +--------+
| | |
v v v
+---------------------+
| |
| Energy Model |
| |
| Framework |
| |
+---------------------+
^ ^ ^
| | | em_register_perf_domain()
+----------+ | +---------+
| | |
+---------------+ +---------------+ +--------------+
| cpufreq-dt | | arm_scmi | | Other |
+---------------+ +---------------+ +--------------+
^ ^ ^
| | |
+--------------+ +---------------+ +--------------+
| Device Tree | | Firmware | | ? |
+--------------+ +---------------+ +--------------+
Drivers (typically, but not limited to, CPUFreq drivers) can register
data in the EM framework using the em_register_perf_domain() API. The
calling driver must provide a callback function with a standardized
signature that will be used by the EM framework to build the power
cost tables of the performance domain. This design should offer a lot of
flexibility to calling drivers which are free of reading information
from any location and to use any technique to compute power costs.
Moreover, the capacity states registered by drivers in the EM framework
are not required to match real performance states of the target. This
is particularly important on targets where the performance states are
not known by the OS.
The power cost coefficients managed by the EM framework are specified in
milli-watts. Although the two potential users of those coefficients (IPA
and EAS) only need relative correctness, IPA specifically needs to
compare the power of CPUs with the power of other components (GPUs, for
example), which are still expressed in absolute terms in their
respective subsystems. Hence, specifying the power of CPUs in
milli-watts should help transitioning IPA to using the EM framework
without introducing new problems by keeping units comparable across
sub-systems.
On the longer term, the EM of other devices than CPUs could also be
managed by the EM framework, which would enable to remove the absolute
unit. However, this is not absolutely required as a first step, so this
extension of the EM framework is left for later.
On the client side, the EM framework offers APIs to access the power
cost tables of a CPU (em_cpu_get()), and to estimate the energy
consumed by the CPUs of a performance domain (em_pd_energy()). Clients
such as the task scheduler can then use these APIs to access the shared
data structures holding the Energy Model of CPUs.
Change-Id: I384cb3d28f37fe82c2943d7208a4cf5dcca2b6bd
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Signed-off-by: Quentin Perret <quentin.perret@arm.com>
Message-Id: <20181016101513.26919-4-quentin.perret@arm.com>
Signed-off-by: Quentin Perret <quentin.perret@arm.com>
Dmitry writes:
"Input updates for v4.19-rc7
- we added a few scheduling points into various input interfaces to
ensure that large writes will not cause RCU stalls
- fixed configuring PS/2 keyboards as wakeup devices on newer
platforms
- added a new Xbox gamepad ID."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: uinput - add a schedule point in uinput_inject_events()
Input: evdev - add a schedule point in evdev_write()
Input: mousedev - add a schedule point in mousedev_write()
Input: i8042 - enable keyboard wakeups by default when s2idle is used
Input: xpad - add support for Xbox1 PDP Camo series gamepad
Previously, on typical consumer laptops, pressing a key on the keyboard
when the system is in suspend would cause it to wake up (default or
unconditional behaviour). This happens because the EC generates a SCI
interrupt in this scenario.
That is no longer true on modern laptops based on Intel WhiskeyLake,
including Acer Swift SF314-55G, Asus UX333FA, Asus UX433FN and Asus
UX533FD. We confirmed with Asus EC engineers that the "Modern Standby"
design has been modified so that the EC no longer generates a SCI
in this case; the keyboard controller itself should be used for wakeup.
In order to retain the standard behaviour of being able to use the
keyboard to wake up the system, enable serio wakeups by default on
platforms that are using s2idle.
Link: https://lkml.kernel.org/r/CAB4CAwfQ0mPMqCLp95TVjw4J0r5zKPWkSvvkK4cpZUGE--w8bQ@mail.gmail.com
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Daniel Drake <drake@endlessm.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Commit ea0212f40c (power: auto select CONFIG_SRCU) made the code in
drivers/base/power/wakeup.c use SRCU instead of RCU, but it forgot to
select CONFIG_SRCU in Kconfig, which leads to the following build
error if CONFIG_SRCU is not selected somewhere else:
drivers/built-in.o: In function `wakeup_source_remove':
(.text+0x3c6fc): undefined reference to `synchronize_srcu'
drivers/built-in.o: In function `pm_print_active_wakeup_sources':
(.text+0x3c7a8): undefined reference to `__srcu_read_lock'
drivers/built-in.o: In function `pm_print_active_wakeup_sources':
(.text+0x3c84c): undefined reference to `__srcu_read_unlock'
drivers/built-in.o: In function `device_wakeup_arm_wake_irqs':
(.text+0x3d1d8): undefined reference to `__srcu_read_lock'
drivers/built-in.o: In function `device_wakeup_arm_wake_irqs':
(.text+0x3d228): undefined reference to `__srcu_read_unlock'
drivers/built-in.o: In function `device_wakeup_disarm_wake_irqs':
(.text+0x3d24c): undefined reference to `__srcu_read_lock'
drivers/built-in.o: In function `device_wakeup_disarm_wake_irqs':
(.text+0x3d29c): undefined reference to `__srcu_read_unlock'
drivers/built-in.o:(.data+0x4158): undefined reference to `process_srcu'
Fix this error by selecting CONFIG_SRCU when PM_SLEEP is enabled.
Fixes: ea0212f40c (power: auto select CONFIG_SRCU)
Cc: 4.2+ <stable@vger.kernel.org> # 4.2+
Signed-off-by: zhangyi (F) <yi.zhang@huawei.com>
[ rjw: Minor subject/changelog fixups ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Pull power management updates from Rafael Wysocki:
"These add a new framework for CPU idle time injection, to be used by
all of the idle injection code in the kernel in the future, fix some
issues and add a number of relatively small extensions in multiple
places.
Specifics:
- Add a new framework for CPU idle time injection (Daniel Lezcano).
- Add AVS support to the armada-37xx cpufreq driver (Gregory
CLEMENT).
- Add support for current CPU frequency reporting to the ACPI CPPC
cpufreq driver (George Cherian).
- Rework the cooling device registration in the imx6q/thermal driver
(Bastian Stender).
- Make the pcc-cpufreq driver refuse to work with dynamic scaling
governors on systems with many CPUs to avoid scalability issues
with it (Rafael Wysocki).
- Fix the intel_pstate driver to report different maximum CPU
frequencies on systems where they really are different and to
ignore the turbo active ratio if hardware-managend P-states (HWP)
are in use; make it use the match_string() helper (Xie Yisheng,
Srinivas Pandruvada).
- Fix a minor deferred probe issue in the qcom-kryo cpufreq driver
(Niklas Cassel).
- Add a tracepoint for the tracking of frequency limits changes (from
Andriod) to the cpufreq core (Ruchi Kandoi).
- Fix a circular lock dependency between CPU hotplug and sysfs
locking in the cpufreq core reported by lockdep (Waiman Long).
- Avoid excessive error reports on driver registration failures in
the ARM cpuidle driver (Sudeep Holla).
- Add a new device links flag to the driver core to make links go
away automatically on supplier driver removal (Vivek Gautam).
- Eliminate potential race condition between system-wide power
management transitions and system shutdown (Pingfan Liu).
- Add a quirk to save NVS memory on system suspend for the ASUS 1025C
laptop (Willy Tarreau).
- Make more systems use suspend-to-idle (instead of ACPI S3) by
default (Tristian Celestin).
- Get rid of stack VLA usage in the low-level hibernation code on
64-bit x86 (Kees Cook).
- Fix error handling in the hibernation core and mark an expected
fall-through switch in it (Chengguang Xu, Gustavo Silva).
- Extend the generic power domains (genpd) framework to support
attaching a device to a power domain by name (Ulf Hansson).
- Fix device reference counting and user limits initialization in the
devfreq core (Arvind Yadav, Matthias Kaehlcke).
- Fix a few issues in the rk3399_dmc devfreq driver and improve its
documentation (Enric Balletbo i Serra, Lin Huang, Nick Milner).
- Drop a redundant error message from the exynos-ppmu devfreq driver
(Markus Elfring)"
* tag 'pm-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (35 commits)
PM / reboot: Eliminate race between reboot and suspend
PM / hibernate: Mark expected switch fall-through
cpufreq: intel_pstate: Ignore turbo active ratio in HWP
cpufreq: Fix a circular lock dependency problem
cpu/hotplug: Add a cpus_read_trylock() function
x86/power/hibernate_64: Remove VLA usage
cpufreq: trace frequency limits change
cpufreq: intel_pstate: Show different max frequency with turbo 3 and HWP
cpufreq: pcc-cpufreq: Disable dynamic scaling on many-CPU systems
cpufreq: qcom-kryo: Silently error out on EPROBE_DEFER
cpufreq / CPPC: Add cpuinfo_cur_freq support for CPPC
cpufreq: armada-37xx: Add AVS support
dt-bindings: marvell: Add documentation for the Armada 3700 AVS binding
PM / devfreq: rk3399_dmc: Fix duplicated opp table on reload.
PM / devfreq: Init user limits from OPP limits, not viceversa
PM / devfreq: rk3399_dmc: fix spelling mistakes.
PM / devfreq: rk3399_dmc: do not print error when get supply and clk defer.
dt-bindings: devfreq: rk3399_dmc: move interrupts to be optional.
PM / devfreq: rk3399_dmc: remove wait for dcf irq event.
dt-bindings: clock: add rk3399 DDR3 standard speed bins.
...
At present, "systemctl suspend" and "shutdown" can run in parrallel. A
system can suspend after devices_shutdown(), and resume. Then the shutdown
task goes on to power off. This causes many devices are not really shut
off. Hence replacing reboot_mutex with system_transition_mutex (renamed
from pm_mutex) to achieve the exclusion. The renaming of pm_mutex as
system_transition_mutex can be better to reflect the purpose of the mutex.
Signed-off-by: Pingfan Liu <kernelfans@gmail.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
This addresses Coverity-ID: 114713 ("Missing break in switch").
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
If PAGE_SIZE is unsigned type then negative error code will be
larger than PAGE_SIZE.
Signed-off-by: Chengguang Xu <cgxu519@gmx.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Pull power management updates from Rafael Wysocki:
"These include a significant update of the generic power domains
(genpd) and Operating Performance Points (OPP) frameworks, mostly
related to the introduction of power domain performance levels,
cpufreq updates (new driver for Qualcomm Kryo processors, updates of
the existing drivers, some core fixes, schedutil governor
improvements), PCI power management fixes, ACPI workaround for
EC-based wakeup events handling on resume from suspend-to-idle, and
major updates of the turbostat and pm-graph utilities.
Specifics:
- Introduce power domain performance levels into the the generic
power domains (genpd) and Operating Performance Points (OPP)
frameworks (Viresh Kumar, Rajendra Nayak, Dan Carpenter).
- Fix two issues in the runtime PM framework related to the
initialization and removal of devices using device links (Ulf
Hansson).
- Clean up the initialization of drivers for devices in PM domains
(Ulf Hansson, Geert Uytterhoeven).
- Fix a cpufreq core issue related to the policy sysfs interface
causing CPU online to fail for CPUs sharing one cpufreq policy in
some situations (Tao Wang).
- Make it possible to use platform-specific suspend/resume hooks in
the cpufreq-dt driver and make the Armada 37xx DVFS use that
feature (Viresh Kumar, Miquel Raynal).
- Optimize policy transition notifications in cpufreq (Viresh Kumar).
- Improve the iowait boost mechanism in the schedutil cpufreq
governor (Patrick Bellasi).
- Improve the handling of deferred frequency updates in the schedutil
cpufreq governor (Joel Fernandes, Dietmar Eggemann, Rafael Wysocki,
Viresh Kumar).
- Add a new cpufreq driver for Qualcomm Kryo (Ilia Lin).
- Fix and clean up some cpufreq drivers (Colin Ian King, Dmitry
Osipenko, Doug Smythies, Luc Van Oostenryck, Simon Horman, Viresh
Kumar).
- Fix the handling of PCI devices with the DPM_SMART_SUSPEND flag set
and update stale comments in the PCI core PM code (Rafael Wysocki).
- Work around an issue related to the handling of EC-based wakeup
events in the ACPI PM core during resume from suspend-to-idle if
the EC has been put into the low-power mode (Rafael Wysocki).
- Improve the handling of wakeup source objects in the PM core (Doug
Berger, Mahendran Ganesh, Rafael Wysocki).
- Update the driver core to prevent deferred probe from breaking
suspend/resume ordering (Feng Kan).
- Clean up the PM core somewhat (Bjorn Helgaas, Ulf Hansson, Rafael
Wysocki).
- Make the core suspend/resume code and cpufreq support the RT patch
(Sebastian Andrzej Siewior, Thomas Gleixner).
- Consolidate the PM QoS handling in cpuidle governors (Rafael
Wysocki).
- Fix a possible crash in the hibernation core (Tetsuo Handa).
- Update the rockchip-io Adaptive Voltage Scaling (AVS) driver (David
Wu).
- Update the turbostat utility (fixes, cleanups, new CPU IDs, new
command line options, built-in "Low Power Idle" counters support,
new POLL and POLL% columns) and add an entry for it to MAINTAINERS
(Len Brown, Artem Bityutskiy, Chen Yu, Laura Abbott, Matt Turner,
Prarit Bhargava, Srinivas Pandruvada).
- Update the pm-graph to version 5.1 (Todd Brandt).
- Update the intel_pstate_tracer utility (Doug Smythies)"
* tag 'pm-4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (128 commits)
tools/power turbostat: update version number
tools/power turbostat: Add Node in output
tools/power turbostat: add node information into turbostat calculations
tools/power turbostat: remove num_ from cpu_topology struct
tools/power turbostat: rename num_cores_per_pkg to num_cores_per_node
tools/power turbostat: track thread ID in cpu_topology
tools/power turbostat: Calculate additional node information for a package
tools/power turbostat: Fix node and siblings lookup data
tools/power turbostat: set max_num_cpus equal to the cpumask length
tools/power turbostat: if --num_iterations, print for specific number of iterations
tools/power turbostat: Add Cannon Lake support
tools/power turbostat: delete duplicate #defines
x86: msr-index.h: Correct SNB_C1/C3_AUTO_UNDEMOTE defines
tools/power turbostat: Correct SNB_C1/C3_AUTO_UNDEMOTE defines
tools/power turbostat: add POLL and POLL% column
tools/power turbostat: Fix --hide Pk%pc10
tools/power turbostat: Build-in "Low Power Idle" counters support
tools/power turbostat: Don't make man pages executable
tools/power turbostat: remove blank lines
tools/power turbostat: a small C-states dump readability immprovement
...
* pm-pci:
PCI / PM: Clean up outdated comments in pci_target_state()
PCI / PM: Do not clear state_saved for devices that remain suspended
* acpi-pm:
ACPI: EC: Dispatch the EC GPE directly on s2idle wake
ACPICA: Introduce acpi_dispatch_gpe()
* pm-sleep:
PM / hibernate: Fix oops at snapshot_write()
PM / wakeup: Make s2idle_lock a RAW_SPINLOCK
PM / s2idle: Make s2idle_wait_head swait based
PM / wakeup: Make events_lock a RAW_SPINLOCK
PM / suspend: Prevent might sleep splats
* pm-avs:
PM / AVS: rockchip-io: add io selectors and supplies for PX30
* pm-qos:
PM / QoS: Drop redundant declaration of pm_qos_get_value()
* pm-core:
PM / runtime: Drop usage count for suppliers at device link removal
PM / runtime: Fixup reference counting of device link suppliers at probe
PM: wakeup: Use pr_debug() for the "aborting suspend" message
PM / core: Drop unused internal inline functions for sysfs
PM / core: Drop unused internal functions for pm_qos sysfs
PM / core: Drop unused internal inline functions for wakeirqs
PM / core: Drop internal unused inline functions for wakeups
PM / wakeup: Only update last time for active wakeup sources
PM / wakeup: Use seq_open() to show wakeup stats
PM / core: Use dev_printk() and symbols in suspend/resume diagnostics
PM / core: Simplify initcall_debug_report() timing
PM / core: Remove unused initcall_debug_report() arguments
PM / core: fix deferred probe breaking suspend resume order
The `s2idle_lock' is acquired during suspend while interrupts are
disabled even on RT. The lock is acquired for short sections only.
Make it a RAW lock which avoids "sleeping while atomic" warnings on RT.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
s2idle_wait_head is used during s2idle with interrupts disabled even on
RT. There is no "custom" wake up function so swait could be used instead
which is also lower weight compared to the wait_queue.
Make s2idle_wait_head a swait_queue_head.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
timekeeping suspend/resume calls read_persistent_clock() which takes
rtc_lock. That results in might sleep warnings because at that point
we run with interrupts disabled.
We cannot convert rtc_lock to a raw spinlock as that would trigger
other might sleep warnings.
As a workaround we disable the might sleep warnings by setting
system_state to SYSTEM_SUSPEND before calling sysdev_suspend() and
restoring it to SYSTEM_RUNNING afer sysdev_resume(). There is no lock
contention because hibernate / suspend to RAM is single-CPU at this
point.
In s2idle's case the system_state is set to SYSTEM_SUSPEND before
timekeeping_suspend() which is invoked by the last CPU. In the resume
case it set back to SYSTEM_RUNNING after timekeeping_resume() which is
invoked by the first CPU in the resume case. The other CPUs will block
on tick_freeze_lock.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
[bigeasy: cover s2idle in tick_freeze() / tick_unfreeze()]
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Same numerical value (for now at least), but a much better documentation
of intent.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
When wakelock support was added, the wakeup_source_add() function
was updated to set the last_time value of the wakeup source. This
has the unintended side effect of producing confusing output from
pm_print_active_wakeup_sources() when a wakeup source is added
prior to a sleep that is blocked by a different wakeup source.
The function pm_print_active_wakeup_sources() will search for the
most recently active wakeup source when no active source is found.
If a wakeup source is added after a different wakeup source blocks
the system from going to sleep it may have a later last_time value
than the blocking source and be output as the last active wakeup
source even if it has never actually been active.
It looks to me like the change to wakeup_source_add() was made to
prevent the wakelock garbage collection from accidentally dropping
a wakelock during the narrow window between adding the wakelock to
the wakelock list in wakelock_lookup_add() and the activation of
the wakeup source in pm_wake_lock().
This commit changes the behavior so that only the last_time of the
wakeup source used by a wakelock is initialized prior to adding it
to the wakeup source list. This preserves the meaning of the
last_time value as the last time the wakeup source was active and
allows a wakeup source that has never been active to have a
last_time value of 0.
Fixes: b86ff9820f (PM / Sleep: Add user space interface for manipulating wakeup sources, v3)
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Pull power management updates from Rafael Wysocki:
"These update the cpuidle poll state definition to reduce excessive
energy usage related to it, add new CPU ID to the RAPL power capping
driver, update the ACPI system suspend code to handle some special
cases better, extend the PM core's device links code slightly, add new
sysfs attribute for better suspend-to-idle diagnostics and easier
hibernation handling, update power management tools and clean up
cpufreq quite a bit.
Specifics:
- Modify the cpuidle poll state implementation to prevent CPUs from
staying in the loop in there for excessive times (Rafael Wysocki).
- Add Intel Cannon Lake chips support to the RAPL power capping
driver (Joe Konno).
- Add reference counting to the device links handling code in the PM
core (Lukas Wunner).
- Avoid reconfiguring GPEs on suspend-to-idle in the ACPI system
suspend code (Rafael Wysocki).
- Allow devices to be put into deeper low-power states via ACPI if
both _SxD and _SxW are missing (Daniel Drake).
- Reorganize the core ACPI suspend-to-idle wakeup code to avoid a
keyboard wakeup issue on Asus UX331UA (Chris Chiu).
- Prevent the PCMCIA library code from aborting suspend-to-idle due
to noirq suspend failures resulting from incorrect assumptions
(Rafael Wysocki).
- Add coupled cpuidle supprt to the Exynos3250 platform (Marek
Szyprowski).
- Add new sysfs file to make it easier to specify the image storage
location during hibernation (Mario Limonciello).
- Add sysfs files for collecting suspend-to-idle usage and time
statistics for CPU idle states (Rafael Wysocki).
- Update the pm-graph utilities (Todd Brandt).
- Reduce the kernel log noise related to reporting Low-power Idle
constraings by the ACPI system suspend code (Rafael Wysocki).
- Make it easier to distinguish dedicated wakeup IRQs in the
/proc/interrupts output (Tony Lindgren).
- Add the frequency table validation in cpufreq to the core and drop
it from a number of cpufreq drivers (Viresh Kumar).
- Drop "cooling-{min|max}-level" for CPU nodes from a couple of DT
bindings (Viresh Kumar).
- Clean up the CPU online error code path in the cpufreq core (Viresh
Kumar).
- Fix assorted issues in the SCPI, CPPC, mediatek and tegra186
cpufreq drivers (Arnd Bergmann, Chunyu Hu, George Cherian, Viresh
Kumar).
- Drop memory allocation error messages from a few places in cpufreq
and cpuildle drivers (Markus Elfring)"
* tag 'pm-4.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (56 commits)
ACPI / PM: Fix keyboard wakeup from suspend-to-idle on ASUS UX331UA
cpufreq: CPPC: Use transition_delay_us depending transition_latency
PM / hibernate: Change message when writing to /sys/power/resume
PM / hibernate: Make passing hibernate offsets more friendly
cpuidle: poll_state: Avoid invoking local_clock() too often
PM: cpuidle/suspend: Add s2idle usage and time state attributes
cpuidle: Enable coupled cpuidle support on Exynos3250 platform
cpuidle: poll_state: Add time limit to poll_idle()
cpufreq: tegra186: Don't validate the frequency table twice
cpufreq: speedstep: Don't validate the frequency table twice
cpufreq: sparc: Don't validate the frequency table twice
cpufreq: sh: Don't validate the frequency table twice
cpufreq: sfi: Don't validate the frequency table twice
cpufreq: scpi: Don't validate the frequency table twice
cpufreq: sc520: Don't validate the frequency table twice
cpufreq: s3c24xx: Don't validate the frequency table twice
cpufreq: qoirq: Don't validate the frequency table twice
cpufreq: pxa: Don't validate the frequency table twice
cpufreq: ppc_cbe: Don't validate the frequency table twice
cpufreq: powernow: Don't validate the frequency table twice
...
Using this helper allows us to avoid the in-kernel calls to the
sys_sync() syscall. The ksys_ prefix denotes that this function
is meant as a drop-in replacement for the syscall. In particular, it
uses the same calling convention as sys_sync().
This patch is part of a series which removes in-kernel calls to syscalls.
On this basis, the syscall entry path can be streamlined. For details, see
http://lkml.kernel.org/r/20180325162527.GA17492@light.dominikbrodowski.net
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
This file is used both for setting the wakeup device without kernel
command line as well as for actually waking the system (when appropriate
swap header is in place).
To avoid confusion on incorrect logs in system log downgrade the
message to debug and make it clearer.
Signed-off-by: Mario Limonciello <mario.limonciello@dell.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Currently the only way to specify a hibernate offset for a
swap file is on the kernel command line.
Add a new /sys/power/resume_offset that lets userspace
specify the offset and disk to use when initiating a hibernate
cycle.
Signed-off-by: Mario Limonciello <mario.limonciello@dell.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The declaration for swsusp_arch_resume marks it as 'asmlinkage', but the
definition in x86-32 does not, and it fails to include the header with the
declaration. This leads to a warning when building with
link-time-optimizations:
kernel/power/power.h:108:23: error: type of 'swsusp_arch_resume' does not match original declaration [-Werror=lto-type-mismatch]
extern asmlinkage int swsusp_arch_resume(void);
^
arch/x86/power/hibernate_32.c:148:0: note: 'swsusp_arch_resume' was previously declared here
int swsusp_arch_resume(void)
This moves the declaration into a globally visible header file and fixes up
both x86 definitions to match it.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Len Brown <len.brown@intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Nicolas Pitre <nico@linaro.org>
Cc: linux-pm@vger.kernel.org
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Bart Van Assche <bart.vanassche@wdc.com>
Link: https://lkml.kernel.org/r/20180202145634.200291-2-arnd@arndb.de
Pull block updates from Jens Axboe:
"This is the main pull request for block IO related changes for the
4.16 kernel. Nothing major in this pull request, but a good amount of
improvements and fixes all over the map. This contains:
- BFQ improvements, fixes, and cleanups from Angelo, Chiara, and
Paolo.
- Support for SMR zones for deadline and mq-deadline from Damien and
Christoph.
- Set of fixes for bcache by way of Michael Lyle, including fixes
from himself, Kent, Rui, Tang, and Coly.
- Series from Matias for lightnvm with fixes from Hans Holmberg,
Javier, and Matias. Mostly centered around pblk, and the removing
rrpc 1.2 in preparation for supporting 2.0.
- A couple of NVMe pull requests from Christoph. Nothing major in
here, just fixes and cleanups, and support for command tracing from
Johannes.
- Support for blk-throttle for tracking reads and writes separately.
From Joseph Qi. A few cleanups/fixes also for blk-throttle from
Weiping.
- Series from Mike Snitzer that enables dm to register its queue more
logically, something that's alwways been problematic on dm since
it's a stacked device.
- Series from Ming cleaning up some of the bio accessor use, in
preparation for supporting multipage bvecs.
- Various fixes from Ming closing up holes around queue mapping and
quiescing.
- BSD partition fix from Richard Narron, fixing a problem where we
can't mount newer (10/11) FreeBSD partitions.
- Series from Tejun reworking blk-mq timeout handling. The previous
scheme relied on atomic bits, but it had races where we would think
a request had timed out if it to reused at the wrong time.
- null_blk now supports faking timeouts, to enable us to better
exercise and test that functionality separately. From me.
- Kill the separate atomic poll bit in the request struct. After
this, we don't use the atomic bits on blk-mq anymore at all. From
me.
- sgl_alloc/free helpers from Bart.
- Heavily contended tag case scalability improvement from me.
- Various little fixes and cleanups from Arnd, Bart, Corentin,
Douglas, Eryu, Goldwyn, and myself"
* 'for-4.16/block' of git://git.kernel.dk/linux-block: (186 commits)
block: remove smart1,2.h
nvme: add tracepoint for nvme_complete_rq
nvme: add tracepoint for nvme_setup_cmd
nvme-pci: introduce RECONNECTING state to mark initializing procedure
nvme-rdma: remove redundant boolean for inline_data
nvme: don't free uuid pointer before printing it
nvme-pci: Suspend queues after deleting them
bsg: use pr_debug instead of hand crafted macros
blk-mq-debugfs: don't allow write on attributes with seq_operations set
nvme-pci: Fix queue double allocations
block: Set BIO_TRACE_COMPLETION on new bio during split
blk-throttle: use queue_is_rq_based
block: Remove kblockd_schedule_delayed_work{,_on}()
blk-mq: Avoid that blk_mq_delay_run_hw_queue() introduces unintended delays
blk-mq: Rename blk_mq_request_direct_issue() into blk_mq_request_issue_directly()
lib/scatterlist: Fix chaining support in sgl_alloc_order()
blk-throttle: track read and write request individually
block: add bdev_read_only() checks to common helpers
block: fail op_is_write() requests to read-only partitions
blk-throttle: export io_serviced_recursive, io_service_bytes_recursive
...
Since pm_mutex is not exported using lock/unlock_system_sleep() from
inside a kernel module causes a "pm_mutex undefined" linker error.
Hence move lock/unlock_system_sleep() into kernel/power/main.c and
export these.
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch converts to bio_first_bvec_all() & bio_first_page_all() for
retrieving the 1st bvec/page, and prepares for supporting multipage bvec.
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
s2disk/s2both may fail unnecessarily and erratically if NR_FILE_MAPPED
is high - for instance when using VMs with VirtualBox and perhaps VMware
Player. In those situations s2disk becomes unreliable and therefore
unusable.
A typical scenario is: user issues a s2disk and it fails. User issues
a second s2disk immediately after that and it succeeds. And user
wonders why.
The problem is caused by minimum_image_size() in snapshot.c. The
value it returns is roughly 100% too high because NR_FILE_MAPPED is
subtracted in its calculation. Eventually the number of preallocated
image pages is falsely too low.
This doesn't matter as long as NR_FILE_MAPPED-values are in a normal
range or in 32bit-environments as the code allows for allocation of
additional pages from highmem.
But with the high values generated by VirtualBox-VMs (a 2-GB-VM causes
NR_FILE_MAPPED go up by 2 GB) it may lead to failure in 64bit-systems.
Not subtracting NR_FILE_MAPPED in minimum_image_size() solves the
problem.
I've done at least hundreds of successful s2both/s2disk now on an
x86_64 system (with and without VirtualBox) which gives me some
confidence that this is right. It has turned s2disk/s2both from
unusable into 100% reliable.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=97201
Signed-off-by: Rainer Fiebig <jrf@mailbox.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
As the page free path makes no distinction between cache hot and cold
pages, there is no real useful ordering of pages in the free list that
allocation requests can take advantage of. Juding from the users of
__GFP_COLD, it is likely that a number of them are the result of copying
other sites instead of actually measuring the impact. Remove the
__GFP_COLD parameter which simplifies a number of paths in the page
allocator.
This is potentially controversial but bear in mind that the size of the
per-cpu pagelists versus modern cache sizes means that the whole per-cpu
list can often fit in the L3 cache. Hence, there is only a potential
benefit for microbenchmarks that alloc/free pages in a tight loop. It's
even worse when THP is taken into account which has little or no chance
of getting a cache-hot page as the per-cpu list is bypassed and the
zeroing of multiple pages will thrash the cache anyway.
The truncate microbenchmarks are not shown as this patch affects the
allocation path and not the free path. A page fault microbenchmark was
tested but it showed no sigificant difference which is not surprising
given that the __GFP_COLD branches are a miniscule percentage of the
fault path.
Link: http://lkml.kernel.org/r/20171018075952.10627-9-mgorman@techsingularity.net
Signed-off-by: Mel Gorman <mgorman@techsingularity.net>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Jan Kara <jack@suse.cz>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* pm-sleep:
freezer: Fix typo in freezable_schedule_timeout() comment
PM / s2idle: Clear the events_check_enabled flag
PM / sleep: Remove pm_complete_with_resume_check()
PM: ARM: locomo: Drop suspend and resume bus type callbacks
PM: Use a more common logging style
PM: Document rules on using pm_runtime_resume() in system suspend callbacks
* pm-cpufreq-sched:
cpufreq: schedutil: Reset cached_raw_freq when not in sync with next_freq
* pm-opp:
PM / OPP: Add dev_pm_opp_{un}register_get_pstate_helper()
PM / OPP: Support updating performance state of device's power domain
PM / OPP: add missing of_node_put() for of_get_cpu_node()
PM / OPP: Rename dev_pm_opp_register_put_opp_helper()
PM / OPP: Add missing of_node_put(np)
PM / OPP: Move error message to debug level
PM / OPP: Use snprintf() to avoid kasprintf() and kfree()
PM / OPP: Move the OPP directory out of power/
Problem: This flag does not get cleared currently in the suspend or
resume path in the following cases:
* In case some driver's suspend routine returns an error.
* Successful s2idle case
* etc?
Why is this a problem: What happens is that the next suspend attempt
could fail even though the user did not enable the flag by writing to
/sys/power/wakeup_count. This is 1 use case how the issue can be seen
(but similar use case with driver suspend failure can be thought of):
1. Read /sys/power/wakeup_count
2. echo count > /sys/power/wakeup_count
3. echo freeze > /sys/power/wakeup_count
4. Let the system suspend, and wakeup the system using some wake source
that calls pm_wakeup_event() e.g. power button or something.
5. Note that the combined wakeup count would be incremented due
to the pm_wakeup_event() in the resume path.
6. After resuming the events_check_enabled flag is still set.
At this point if the user attempts to freeze again (without writing to
/sys/power/wakeup_count), the suspend would fail even though there has
been no wake event since the past resume.
Address that by clearing the flag just before a resume is completed,
so that it is always cleared for the corner cases mentioned above.
Signed-off-by: Rajat Jain <rajatja@google.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert printks to pr_<level>.
Miscellanea:
o Use pr_fmt with "PM:" and remove "PM: " from format strings
o Coalesce format strings and realign format arguments
o Convert an embedded incorrect function name to "%s: ", __func__
o Convert a couple multi-line formats to multiple pr_<level> calls
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The drivers/base/power/ directory is special and contains code related
to power management core like system suspend/resume, hibernation, etc.
It was fine to keep the OPP code inside it when we had just one file for
it, but it is growing now and already has a directory for itself.
Lets move it directly under drivers/ directory, just like cpufreq and
cpuidle.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The role of the ->wake() platform callback for suspend-to-idle is to
deal with possible spurious wakeups, among other things. The ACPI
implementation of it, acpi_s2idle_wake(), additionally checks the
conditions for entering the Low Power S0 Idle state by the platform
and reports the ones that have not been met.
However, the ->wake() platform callback is invoked after calling
dpm_noirq_resume_devices(), which means that the power states of some
devices may have changed since s2idle_enter() returned, so some unmet
Low Power S0 Idle conditions may be reported incorrectly as a result
of that.
To avoid these false positives, reorder the invocations of the
dpm_noirq_resume_devices() routine and the ->wake() platform callback
in s2idle_loop().
Fixes: 726fb6b4f2 (ACPI / PM: Check low power idle constraints for debug only)
Tested-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
