Datasheet on collision:
SMBus Collision (SMBCOL_STS)
This bit is set when a SMBus Collision condition occurs and
SMBus Host loses in the bus arbitration. The software should
clear this bit and re-start SMBus operation.
As the status will be cleared in transaction_end, we can remove the
sis630_write and prepare to return -EAGAIN to retry.
Signed-off-by: Amaury Decrême <amaury.decreme@gmail.com>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Wolfram Sang <wolfram@the-dreams.de>
The sticky bits must be cleared at the end of the transaction by writing
a 1 to all fields.
Datasheet:
SMBus Status (SMB_STS)
The following registers are all sticky bits and only can be
cleared by writing a one to their corresponding fields.
Signed-off-by: Amaury Decrême <amaury.decreme@gmail.com>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Wolfram Sang <wolfram@the-dreams.de>
It was observed the Host Clock Divider was not written by the driver. It
was still set to (default) 0, if not already set by BIOS, which caused
garbage on SMBus.
This driver adds a parameters which is used to calculate the divider
appropriately for a default bitrate of 100 KHz. This new divider is only
applied if the clock divider is still default 0.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Wolfram Sang <wolfram@the-dreams.de>
ARC700 includes 2 in-core 32bit timers TIMER0 and TIMER1.
Both have exactly same capabilies.
* programmable to count from TIMER<n>_CNT to TIMER<n>_LIMIT
* for count 0 and LIMIT ~1, provides a free-running counter by
auto-wrapping when limit is reached.
* optionally interrupt when LIMIT is reached (oneshot event semantics)
* rearming the interrupt provides periodic semantics
* run at CPU clk
ARC Linux uses TIMER0 for clockevent (periodic/oneshot) and TIMER1 for
clocksource (free-running clock).
Newer cores provide RTSC insn which gives a 64bit cpu clk snapshot hence
is more apt for clocksource when available.
SMP poses a bit of challenge for global timekeeping clocksource /
sched_clock() backend:
-TIMER1 based local clocks are out-of-sync hence can't be used
(thus we default to jiffies based cs as well as sched_clock() one/both
of which platform can override with it's specific hardware assist)
-RTSC is only allowed in SMP if it's cross-core-sync (Kconfig glue
ensures that) and thus usable for both requirements.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Hand optimised asm code for ARC700 pipeline.
Originally written/optimized by Joern Rennecke
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Cc: Joern Rennecke <joern.rennecke@embecosm.com>
* L1_CACHE_SHIFT
* PAGE_SIZE, PAGE_OFFSET
* struct pt_regs, struct user_regs_struct
* struct thread_struct, cpu_relax(), task_pt_regs(), start_thread(), ...
* struct thread_info, THREAD_SIZE, INIT_THREAD_INFO(), TIF_*, ...
* BUG()
* ELF_*
* Elf_*
To disallow user-space visibility into some of the core kernel data-types
such as struct pt_regs, #ifdef __KERNEL__ which also makes the UAPI header
spit (further patch in the series) to NOT export it to asm/uapi/ptrace.h
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Cc: Jonas Bonn <jonas.bonn@gmail.com>
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Acked-by: Arnd Bergmann <arnd@arndb.de>
arches can have more efficient implementation of these routines
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Override asm-generic implementations. We basically gain on 2 fronts
* checks for alignment no longer needed as we are only doing "unit"
sized copies.
(Careful observer could argue that While the kernel buffers are aligned,
the user buffer in theory might not be - however in that case the
user space is already broken when it tries to deref a hword/word
straddling word boundary - so we are not making it any worse).
* __copy_{to,from}_user( ) returns bytes that couldn't be copied,
whereas get_user() returns 0 for success or -EFAULT (not size). Thus
the code to do leftover bytes calculation can be avoided as well.
The savings were significant: ~17k of code.
bloat-o-meter vmlinux_uaccess_pre vmlinux_uaccess_post
add/remove: 0/4 grow/shrink: 8/118 up/down: 1262/-18758 (-17496)
^^^^^^^^^
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
As of now these default to calling the arch provided __copy_{to,from}_user()
routines which being general purpose (w.r.t buffer alignment and lengths)
would lead to alignment checks in generated code (for arches which don't
support unaligned load/stores).
Given that in this case we already know that data involved is "unit"
sized and aligned, using the vanilla copy backend is a bit wasteful.
This change thus allows arches to over-ride the aforementioned routines.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
This is because mm_segment_t is exported by arch code, while seqment_eq
assumes it will have .seg element.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
This covers the UP / SMP (with no hardware assist for atomic r-m-w) as
well as ARC700 LLOCK/SCOND insns based.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
ARC700 has an in-core intc which provides 2 priorities (a.k.a.) "levels"
of interrupts (per IRQ) hencforth referred to as L1/L2 interrupts.
CPU flags register STATUS32 has Interrupt Enable bits per level (E1/E2)
to globally enable (or disable) all IRQs at a level. Hence the
implementation of arch_local_irq_{save,restore,enable,disable}( )
The STATUS32 reg can be r/w only using the AUX Interface of ARC, hence
the use of LR/SR instructions. Further, E1/E2 bits in there can only be
updated using the FLAG insn.
The intc supports 32 interrupts - and per IRQ enabling is controlled by
a bit in the AUX_IENABLE register, hence the implmentation of
arch_{,un}mask_irq( ) routines.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Arnd in his review pointed out that arch Kconfig organisation has several
deficiencies:
* Build time entries for things which can be runtime extracted from DT
(e.g. SDRAM size, core clk frequency..)
* Not multi-platform-image-build friendly (choice .. endchoice constructs)
* cpu variants support (750/770) is exclusive.
The first 2 have been fixed in subsequent patches.
Due to the nature of the 750 and 770, it is not possible to build for
both together, w/o special runtime glue code which would hurt
performance.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
The snd_compr_update_tstamp() can only fill in the snd_compr_tstamp
if the codec implements the pointer() function. If that happened
the code was previously returning uninitialized garbage in the
tstamp because it wasn't initialized anywhere.
This change zero-fills the tstamp in the two places it is used
before calling snd_compr_update_tstamp(), and also has
snd_compr_update_tstamp() return an error indication if it
can't provide a tstamp. For the case of snd_compr_calc_avail()
it ignores this error because we still need to return info on
the available buffer space even if we can't provide tstamp
info - when the tstamp is not valid all fields are now
guaranteed to be zero.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We currently can not insert policies with mark and mask
such that some flows would be matched from both policies.
We make this possible when the priority of these policies
are different. If both policies match a flow, the one with
the higher priority is used.
Reported-by: Emmanuel Thierry <emmanuel.thierry@telecom-bretagne.eu>
Reported-by: Romain Kuntz <r.kuntz@ipflavors.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
ASoC: Updates for v3.9
A fairly quiet release for ASoC:
- Support for a wider range of hardware in the compressed stream code.
- The ability to mute capture streams as well as playback streams while
inactive.
- DT support for AK4642, FSI, Samsung I2S and WM8962.
- AC'97 support for Tegra.
- New driver for max98090, replacing the stub which was there.
Due to dependencies we've also got support for asynchronous I/O in regmap
and DTification of DMA support for Samsung platforms (used only by the
I2S driver and SPI) merged here as well.
Adds quirks and mixer support for the M-Audio Fast Track C600 USB
audio interface. This device is very similar to the C400 - the C600
simply has some more inputs and outputs, so the existing C400 support
is extended to support this device as well.
Signed-off-by: Matt Gruskin <matthew.gruskin@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
struct compat_ucontext * is a 64-bit pointer, so we need to use a
compat_uptr_t instead to avoid declaring a structure incompatible with
what AArch32 userspace expects.
Cc: <stable@vger.kernel.org>
Reported-by: Edmund Grimley-Evans <Edmund.Grimley-Evans@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
* acpi-lpss:
ACPI / platform: create LPSS clocks if Lynxpoint devices are found during scan
clk: x86: add support for Lynxpoint LPSS clocks
x86: add support for Intel Low Power Subsystem
ACPI / platform: fix comment about the platform device name
ACPI: add support for CSRT table
* acpi-pm: (35 commits)
ACPI / PM: Handle missing _PSC in acpi_bus_update_power()
ACPI / PM: Do not power manage devices in unknown initial states
ACPI / PM: Fix acpi_bus_get_device() check in drivers/acpi/device_pm.c
ACPI / PM: Fix /proc/acpi/wakeup for devices w/o bus or parent
ACPI / PM: Fix consistency check for power resources during resume
ACPI / PM: Expose lists of device power resources to user space
sysfs: Functions for adding/removing symlinks to/from attribute groups
ACPI / PM: Expose current status of ACPI power resources
ACPI / PM: Expose power states of ACPI devices to user space
ACPI / scan: Prevent device add uevents from racing with user space
ACPI / PM: Fix device power state value after transitions to D3cold
ACPI / PM: Use string "D3cold" to represent ACPI_STATE_D3_COLD
ACPI / PM: Sanitize checks in acpi_power_on_resources()
ACPI / PM: Always evaluate _PSn after setting power resources
ACPI / PM: Introduce helper for executing _PSn methods
ACPI / PM: Make acpi_bus_init_power() more robust
ACPI / PM: Fix build for unusual combination of Kconfig options
ACPI / PM: remove leading whitespace from #ifdef
ACPI / PM: Consolidate suspend-specific and hibernate-specific code
ACPI / PM: Move device power management functions to device_pm.c
...
* acpica: (56 commits)
ACPICA: Update version to 20130117
ACPICA: Update predefined info table for _MLS method
ACPICA: Remove some extraneous newlines in ACPI_ERROR type calls
ACPICA: iASL/Disassembler: Add option to ignore NOOP opcodes/operators
ACPICA: AcpiGetSleepTypeData: Allow \_Sx to return either 1 or 2 integers
ACPICA: Update ACPICA copyrights to 2013
ACPICA: Update predefined info table
ACPICA: Cleanup table handler naming conflicts.
ACPICA: Source restructuring: split large files into 8 new files.
ACPICA: Cleanup PM_TIMER_FREQUENCY definition.
ACPICA: Cleanup ACPI_DEBUG_PRINT macros to fix potential build breakages.
ACPICA: Update version to 20121220.
ACPICA: Interpreter: Fix Store() when implicit conversion is not possible.
ACPICA: Resources: Split interrupt share/wake bits into two fields.
ACPICA: Resources: Support for ACPI 5 wake bit in ExtendedInterrupt descriptor.
ACPICA: Interpreter: Add warning if 64-bit constant appears in 32-bit table.
ACPICA: Update ACPICA initialization messages.
ACPICA: Namespace: Eliminate dot...dot output during initialization.
ACPICA: Resource manager: Add support for ACPI 5 wake bit in IRQ descriptor.
ACPICA: Fix possible memory leak in dispatcher error path.
...
* acpi-scan: (30 commits)
ACPI / scan: Fix acpi_bus_get_device() check in acpi_match_device()
ACPI / scan: Make namespace scanning and trimming mutually exclusive
ACPI / scan: Make it clear that acpi_bus_trim() cannot fail
ACPI / scan: Drop acpi_bus_add() and use acpi_bus_scan() instead
ACPI: update ej_event interface to take acpi_device
ACPI / scan: Add second pass to acpi_bus_trim()
ACPI / scan: Change the implementation of acpi_bus_trim()
ACPI / scan: Drop the second argument of acpi_bus_trim()
ACPI / scan: Drop the second argument of acpi_device_unregister()
ACPI: Remove the ops field from struct acpi_device
ACPI: remove unused acpi_op_bind and acpi_op_unbind
ACPI / scan: Fix check of device_attach() return value.
ACPI / scan: Treat power resources in a special way
ACPI: Remove unused struct acpi_pci_root.id member
ACPI: Drop ACPI device .bind() and .unbind() callbacks
ACPI / PCI: Move the _PRT setup and cleanup code to pci-acpi.c
ACPI / PCI: Rework the setup and cleanup of device wakeup
ACPI: Add .setup() and .cleanup() callbacks to struct acpi_bus_type
ACPI: Make acpi_bus_scan() and acpi_bus_add() take only one argument
ACPI: Replace ACPI device add_type field with a match_driver flag
...
In preparation to support the regmap debugfs ranges functionality
factor this code out to a separate function. We'll need to ensure
that the value has been correctly calculated from two separate places
in the code.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Optimize this so that we can better guess where to start scanning
from. We know the length of the register field format, therefore
given the file pointer position align to the nearest register
field and scan from there onwards. We round down in this calculation
and we let the rest of the code figure out where to start scanning
from.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We are keeping track of the maximum register as well, this will make
things easier for us in sharing this code with the code implementing
the register ranges functionality. It also simplifies a bit the
calculations when looking for the relevant block:offset from within
the cache.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
