The mv88e6xxx_port_setup_mac checks if the requested MAC settings are
different from the current ones, and if not, does nothing (since chaning
them requires putting the link down).
In this check it only looks if the triplet [link, speed, duplex] is
being changed.
This patch adds support to also check if the mode parameter (of type
phy_interface_t) is requested to be changed. The current mode is
computed by the ->port_link_state() method, and if it is different from
PHY_INTERFACE_MODE_NA, we check for equality with the requested mode.
In the implementations of the mv88e6250_port_link_state() method we set
the current mode to PHY_INTERFACE_MODE_NA - so the code does not check
for mode change on 6250.
In the mv88e6352_port_link_state() method, we use the cached cmode of
the port to determine the mode as phy_interface_t (and if it is not
enough, eg. for RGMII, we also look at the port control register for
RX/TX timings).
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change implements retrieving all the error counters from the PHY.
The counters require that the RxErrCnt register (0x0014) be read first,
after which copies of the counters are latched into the registers. This
ensures that all registers read after RxErrCnt are synchronized at the
moment that they are read.
The counter values need to be accumulated by the driver, as each time that
RxErrCnt is read, the values that are latched are the ones that have
incremented from the last read.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Down-speed auto-negotiation may not always be enabled, in which case the
PHY won't down-shift to 100 or 10 during auto-negotiation.
This change enables downshift and configures the number of retries to
default 4 (which is also in the datasheet
The downshift control mechanism can also be controlled via the phy-tunable
interface (ETHTOOL_PHY_DOWNSHIFT control).
The change has been adapted from the Aquantia PHY driver.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ADIN PHYs supports 4 types of reset:
1. The standard PHY reset via BMCR_RESET bit in MII_BMCR reg
2. Reset via GPIO
3. Reset via reg GeSftRst (0xff0c) & reload previous pin configs
4. Reset via reg GeSftRst (0xff0c) & request new pin configs
Resets 2, 3 & 4 are almost identical, with the exception that the crystal
oscillator is available during reset for 2.
This change implements subsystem software reset via the GeSftRst and
reloading the previous pin configuration (so reset number 3).
This will also reset the PHY core regs (similar to reset 1).
Since writing bit 1 to reg GeSftRst is self-clearing, the only thing that
can be done, is to write to that register, wait a specific amount of time
(10 milliseconds should be enough) and try to read back and check if there
are no errors on read. A busy-wait-read won't work well, and may sometimes
work or not work.
In case phylib is configured to also do a reset via GPIO, the ADIN PHY may
be reset twice when the PHY device registers, but that isn't a problem,
since it's being done on boot (or PHY device register).
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ADIN1200 & ADIN1300 PHYs support EEE by using standard Clause 45 access
to access MMD registers for EEE.
The EEE register addresses (when using Clause 22) are available at
different addresses (than Clause 45), and since accessing these regs (via
Clause 22) needs a special mechanism, a translation table is required to
convert these addresses.
For Clause 45, this is not needed since the driver will likely never use
this access mode.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ADIN PHYs support automatic MDI/MDIX negotiation. By default this is
disabled, so this is enabled at `config_init`.
This is controlled via the PHY Control 1 register.
The supported modes are:
1. Manual MDI
2. Manual MDIX
3. Auto MDIX - prefer MDIX
4. Auto MDIX - prefer MDI
The phydev mdix & mdix_ctrl fields include modes 3 & 4 into a single
auto-mode. So, the default mode this driver enables is 4 when Auto-MDI mode
is used.
When detecting MDI/MDIX mode, a combination of the PHY Control 1 register
and PHY Status 1 register is used to determine the correct MDI/MDIX mode.
If Auto-MDI mode is not set, then the manual MDI/MDIX mode is returned.
If Auto-MDI mode is set, then MDIX mode is returned differs from the
preferred MDI/MDIX mode.
This covers all cases where:
1. MDI preferred & Pair01Swapped == MDIX
2. MDIX preferred & Pair01Swapped == MDI
3. MDI preferred & ! Pair01Swapped == MDIX
4. MDIX preferred & ! Pair01Swapped == MDI
The preferred MDI/MDIX mode is not configured via SW, but can be configured
via HW pins. Note that the `Pair01Swapped` is the Green-Yellow physical
pairs.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The FIFO depth can be configured for the RMII mode. This change adds
support for doing this via device-tree (or ACPI).
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The internal delays for the RGMII are configurable for both RX & TX. This
change adds support for configuring them via device-tree (or ACPI).
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ADIN1300 chip supports RGMII, RMII & MII modes. Default (if
unconfigured) is RGMII.
This change adds support for configuring these modes via the device
registers.
For RGMII with internal delays (modes RGMII_ID,RGMII_TXID, RGMII_RXID),
the default delay is 2 ns. This can be configurable and will be done in
a subsequent change.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both ADIN1200 & ADIN1300 support Clause 45 access for some registers.
The Extended Management Interface (EMI) registers are accessible via both
Clause 45 (at register MDIO_MMD_VEND1) and using Clause 22.
The Clause 22 access for MMD regs differs from the standard one defined by
802.3. The ADIN PHYs use registers ExtRegPtr (0x0010) and ExtRegData
(0x0011) to access Clause 45 & EMI registers.
The indirect access is done via the following mechanism (for both R/W):
1. Write the address of the register in the ExtRegPtr
2. Read/write the value of the register via reg ExtRegData
This mechanism is needed to manage configuration of chip settings and to
access EEE registers via Clause 22.
Since Clause 45 access will likely never be used, it is not implemented via
this hook.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change adds support for Analog Devices Industrial Ethernet PHYs.
Particularly the PHYs this driver adds support for:
* ADIN1200 - Robust, Industrial, Low Power 10/100 Ethernet PHY
* ADIN1300 - Robust, Industrial, Low Latency 10/100/1000 Gigabit
Ethernet PHY
The 2 chips are register compatible with one another. The main difference
being that ADIN1200 doesn't operate in gigabit mode.
The chips can be operated by the Generic PHY driver as well via the
standard IEEE PHY registers (0x0000 - 0x000F) which are supported by the
kernel as well. This assumes that configuration of the PHY has been done
completely in HW, according to spec.
Configuration can also be done via registers, which will be supported by
this driver.
Datasheets:
https://www.analog.com/media/en/technical-documentation/data-sheets/ADIN1300.pdfhttps://www.analog.com/media/en/technical-documentation/data-sheets/ADIN1200.pdf
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't compare the parent clock name with a NULL name in the
clk_parent_map. This prevents a kernel crash when passing NULL
core->parents[i].name to strcmp().
An example which triggered this is a mux clock with four parents when
each of them is referenced in the clock driver using
clk_parent_data.fw_name and then calling clk_set_parent(clk, 3rd_parent)
on this mux.
In this case the first parent is also the HW default so
core->parents[i].hw is populated when the clock is registered. Calling
clk_set_parent(clk, 3rd_parent) will then go through all parents and
skip the first parent because it's hw pointer doesn't match. For the
second parent no hw pointer is cached yet and clk_core_get(core, 1)
returns a non-matching pointer (which is correct because we are comparing
the second with the third parent). Comparing the result of
clk_core_get(core, 2) with the requested parent gives a match. However
we don't reach this point because right after the clk_core_get(core, 1)
mismatch the old code tried to !strcmp(parent->name, NULL) (where the
second argument is actually core->parents[i].name, but that was never
populated by the clock driver).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lkml.kernel.org/r/20190815223155.21384-1-martin.blumenstingl@googlemail.com
Fixes: fc0c209c14 ("clk: Allow parents to be specified without string names")
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Calls to clk_core_get() will return ERR_PTR(-EINVAL) if we've started
migrating a clk driver to use the DT based style of specifying parents
but we haven't made any DT updates yet. This happens when we pass a
non-NULL value as the 'name' argument of of_parse_clkspec(). That
function returns -EINVAL in such a situation, instead of -ENOENT like we
expected. The return value comes back up to clk_core_fill_parent_index()
which proceeds to skip calling clk_core_lookup() because the error
pointer isn't equal to -ENOENT, it's -EINVAL.
Furthermore, we blindly overwrite the error pointer returned by
clk_core_get() with NULL when there isn't a legacy .name member
specified in the parent map. This isn't too bad right now because we
don't really care to differentiate NULL from an error, but in the future
we should only try to do a legacy lookup if we know we might find
something. This way DT lookups that fail don't try to lookup based on
strings when there isn't any string to match, hiding the error from DT
parsing.
Fix both these problems so that clk provider drivers can use the new
style of parent mapping without having to also update their DT at the
same time. This patch is based on an earlier patch from Taniya Das which
checked for -EINVAL in addition to -ENOENT return values from
clk_core_get().
Fixes: 601b6e9330 ("clk: Allow parents to be specified via clkspec index")
Cc: Taniya Das <tdas@codeaurora.org>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Reported-by: Taniya Das <tdas@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lkml.kernel.org/r/20190813214147.34394-1-sboyd@kernel.org
Tested-by: Taniya Das <tdas@codeaurora.org>
Pull power management fixes from Rafael Wysocki:
"These add a check to avoid recent suspend-to-idle power regression on
systems with NVMe drives where the PCIe ASPM policy is "performance"
(or when the kernel is built without ASPM support), fix an issue
related to frequency limits in the schedutil cpufreq governor and fix
a mistake related to the PM QoS usage in the cpufreq core introduced
recently.
Specifics:
- Disable NVMe power optimization related to suspend-to-idle added
recently on systems where PCIe ASPM is not able to put PCIe links
into low-power states to prevent excess power from being drawn by
the system while suspended (Rafael Wysocki).
- Make the schedutil governor handle frequency limits changes
properly in all cases (Viresh Kumar).
- Prevent the cpufreq core from treating positive values returned by
dev_pm_qos_update_request() as errors (Viresh Kumar)"
* tag 'pm-5.3-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
nvme-pci: Allow PCI bus-level PM to be used if ASPM is disabled
PCI/ASPM: Add pcie_aspm_enabled()
cpufreq: schedutil: Don't skip freq update when limits change
cpufreq: dev_pm_qos_update_request() can return 1 on success
Pull drm fixes from Dave Airlie:
"Nothing too crazy this week, one amdgpu fix to use vmalloc for a
struct that grew in size, and another MST fix for nouveau, and some
other misc fixes:
i915:
- single GVT use after free fix
scheduler:
- entity destruction race fix
amdgpu:
- struct allocation fix
- gfx9 soft recovery fix
nouveau:
- followup MST fix
ast:
- vga register race fix"
* tag 'drm-fixes-2019-08-16' of git://anongit.freedesktop.org/drm/drm:
drm/nouveau: Only recalculate PBN/VCPI on mode/connector changes
drm/ast: Fixed reboot test may cause system hanged
drm/scheduler: use job count instead of peek
drm/amd/display: use kvmalloc for dc_state (v2)
drm/amdgpu: fix gfx9 soft recovery
drm/i915: Use after free in error path in intel_vgpu_create_workload()
The R-Car LVDS encoder units support dual-link operations by splitting
the pixel output between the primary encoder and the companion encoder.
Currently the companion encoder fails at probe time, causing the
registration of the primary to fail as well, preventing the whole DU unit
from being registered at all.
Fix this by not bailing out from probe with error if the
"renesas,companion" property is not specified.
Fixes: fa440d8703 ("drm: rcar-du: lvds: Add support for dual-link mode")
Reported-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Vinod writes:
soundwire fixes for v5.3-rc5
Pierre sent fixes which are queued now for v5.3-rc5 are:
- regmap dependecy
- cadence register definitions
* tag 'soundwire-5.3-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/soundwire:
soundwire: fix regmap dependencies and align with other serial links
soundwire: cadence_master: fix definitions for INTSTAT0/1
soundwire: cadence_master: fix register definition for SLAVE_STATE
This patch adds support for PTP Hardware Clock (PHC) to the Ocelot
switch for both PTP 1-step and 2-step modes.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In struct frame_info, the cpuq member is never used. This cosmetic patch
removes it from the structure, and from the parsing of the frame header
as it's only set but never used.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This cosmetic patch improves the frame header parsing readability by
introducing a new macro to access and mask its fields.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for using the PTP register range, and adds a
description of its registers. This bank is used when configuring PTP.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a crash that was introduced by the commit 724376a04d. The crash is
reported here: https://gitlab.com/cryptsetup/cryptsetup/issues/468
When reading from the integrity device, the function
dm_integrity_map_continue calls find_journal_node to find out if the
location to read is present in the journal. Then, it calculates how many
sectors are consecutively stored in the journal. Then, it locks the range
with add_new_range and wait_and_add_new_range.
The problem is that during wait_and_add_new_range, we hold no locks (we
don't hold ic->endio_wait.lock and we don't hold a range lock), so the
journal may change arbitrarily while wait_and_add_new_range sleeps.
The code then goes to __journal_read_write and hits
BUG_ON(journal_entry_get_sector(je) != logical_sector); because the
journal has changed.
In order to fix this bug, we need to re-check the journal location after
wait_and_add_new_range. We restrict the length to one block in order to
not complicate the code too much.
Fixes: 724376a04d ("dm integrity: implement fair range locks")
Cc: stable@vger.kernel.org # v4.19+
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
dm-zoned is observed to lock up or livelock in case of hardware
failure or some misconfiguration of the backing zoned device.
This patch adds a new dm-zoned target function that checks the status of
the backing device. If the request queue of the backing device is found
to be in dying state or the SCSI backing device enters offline state,
the health check code sets a dm-zoned target flag prompting all further
incoming I/O to be rejected. In order to detect backing device failures
timely, this new function is called in the request mapping path, at the
beginning of every reclaim run and before performing any metadata I/O.
The proper way out of this situation is to do
dmsetup remove <dm-zoned target>
and recreate the target when the problem with the backing device
is resolved.
Fixes: 3b1a94c88b ("dm zoned: drive-managed zoned block device target")
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Some errors are ignored in the I/O path during queueing chunks
for processing by chunk works. Since at least these errors are
transient in nature, it should be possible to retry the failed
incoming commands.
The fix -
Errors that can happen while queueing chunks are carried upwards
to the main mapping function and it now returns DM_MAPIO_REQUEUE
for any incoming requests that can not be properly queued.
Error logging/debug messages are added where needed.
Fixes: 3b1a94c88b ("dm zoned: drive-managed zoned block device target")
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
There are several places in reclaim code where errors are not
propagated to the main function, dmz_reclaim(). This function
is responsible for unlocking zones that might be still locked
at the end of any failed reclaim iterations. As the result,
some device zones may be left permanently locked for reclaim,
degrading target's capability to reclaim zones.
This patch fixes these issues as follows -
Make sure that dmz_reclaim_buf(), dmz_reclaim_seq_data() and
dmz_reclaim_rnd_data() return error codes to the caller.
dmz_reclaim() function is renamed to dmz_do_reclaim() to avoid
clashing with "struct dmz_reclaim" and is modified to return the
error to the caller.
dmz_get_zone_for_reclaim() now returns an error instead of NULL
pointer and reclaim code checks for that error.
Error logging/debug messages are added where necessary.
Fixes: 3b1a94c88b ("dm zoned: drive-managed zoned block device target")
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
This patch fixes a problem in dm-kcopyd that may leave jobs in
complete queue indefinitely in the event of backing storage failure.
This behavior has been observed while running 100% write file fio
workload against an XFS volume created on top of a dm-zoned target
device. If the underlying storage of dm-zoned goes to offline state
under I/O, kcopyd sometimes never issues the end copy callback and
dm-zoned reclaim work hangs indefinitely waiting for that completion.
This behavior was traced down to the error handling code in
process_jobs() function that places the failed job to complete_jobs
queue, but doesn't wake up the job handler. In case of backing device
failure, all outstanding jobs may end up going to complete_jobs queue
via this code path and then stay there forever because there are no
more successful I/O jobs to wake up the job handler.
This patch adds a wake() call to always wake up kcopyd job wait queue
for all I/O jobs that fail before dm_io() gets called for that job.
The patch also sets the write error status in all sub jobs that are
failed because their master job has failed.
Fixes: b73c67c2cb ("dm kcopyd: add sequential write feature")
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Revert the commit bd293d071f. The proper
fix has been made available with commit d0a255e795 ("loop: set
PF_MEMALLOC_NOIO for the worker thread").
Note that the fix offered by commit bd293d071f doesn't really prevent
the deadlock from occuring - if we look at the stacktrace reported by
Junxiao Bi, we see that it hangs in bit_wait_io and not on the mutex -
i.e. it has already successfully taken the mutex. Changing the mutex
from mutex_lock to mutex_trylock won't help with deadlocks that happen
afterwards.
PID: 474 TASK: ffff8813e11f4600 CPU: 10 COMMAND: "kswapd0"
#0 [ffff8813dedfb938] __schedule at ffffffff8173f405
#1 [ffff8813dedfb990] schedule at ffffffff8173fa27
#2 [ffff8813dedfb9b0] schedule_timeout at ffffffff81742fec
#3 [ffff8813dedfba60] io_schedule_timeout at ffffffff8173f186
#4 [ffff8813dedfbaa0] bit_wait_io at ffffffff8174034f
#5 [ffff8813dedfbac0] __wait_on_bit at ffffffff8173fec8
#6 [ffff8813dedfbb10] out_of_line_wait_on_bit at ffffffff8173ff81
#7 [ffff8813dedfbb90] __make_buffer_clean at ffffffffa038736f [dm_bufio]
#8 [ffff8813dedfbbb0] __try_evict_buffer at ffffffffa0387bb8 [dm_bufio]
#9 [ffff8813dedfbbd0] dm_bufio_shrink_scan at ffffffffa0387cc3 [dm_bufio]
#10 [ffff8813dedfbc40] shrink_slab at ffffffff811a87ce
#11 [ffff8813dedfbd30] shrink_zone at ffffffff811ad778
#12 [ffff8813dedfbdc0] kswapd at ffffffff811ae92f
#13 [ffff8813dedfbec0] kthread at ffffffff810a8428
#14 [ffff8813dedfbf50] ret_from_fork at ffffffff81745242
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org
Fixes: bd293d071f ("dm bufio: fix deadlock with loop device")
Depends-on: d0a255e795 ("loop: set PF_MEMALLOC_NOIO for the worker thread")
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
The patch adds driver interface for reading the config attributes from user
provided buffer, and updates these values on nvm config flash partition.
This is basically an expansion of our existing ethtool -f implementation.
The management FW has exposed an additional method of configuring some of
the nvram options, and this makes use of that. This implementation will
come into use when newer FW files which contain configuration directives
employing this API will be provided to ethtool -f.
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch adds API for configuring the NVM config attributes using
Management FW (MFW) interfaces.
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In myri10ge_probe(), myri10ge_alloc_slices() is invoked to allocate slices
related structures. Later on, myri10ge_request_irq() is used to get an irq.
However, if this process fails, the allocated slices related structures are
not deallocated, leading to memory leaks. To fix this issue, revise the
target label of the goto statement to 'abort_with_slices'.
Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marc Kleine-Budde says:
====================
pull-request: can-next 2019-08-14
this is a pull request for net-next/master consisting of 41 patches.
The first two patches are for the kvaser_pciefd driver: Christer Beskow
removes unnecessary code in the kvaser_pciefd_pwm_stop() function,
YueHaibing removes the unused including of <linux/version.h>.
In the next patch YueHaibing also removes the unused including of
<linux/version.h> in the f81601 driver.
In the ti_hecc driver the next 6 patches are by me and fix checkpatch
warnings. YueHaibing's patch removes an unused variable in the
ti_hecc_mailbox_read() function.
The next 6 patches all target the xilinx_can driver. Anssi Hannula's
patch fixes a chip start failure with an invalid bus. The patch by
Venkatesh Yadav Abbarapu skips an error message in case of a deferred
probe. The 3 patches by Appana Durga Kedareswara rao fix the RX and TX
path for CAN-FD frames. Srinivas Neeli's patch fixes the bit timing
calculations for CAN-FD.
The next 12 patches are by me and several checkpatch warnings in the
af_can, raw and bcm components.
Thomas Gleixner provides a patch for the bcm, which switches the timer
to HRTIMER_MODE_SOFT and removes the hrtimer_tasklet.
Then 6 more patches by me for the gw component, which fix checkpatch
warnings, followed by 2 patches by Oliver Hartkopp to add CAN-FD
support.
The vcan driver gets 3 patches by me, fixing checkpatch warnings.
And finally a patch by Andre Hartmann to fix typos in CAN's netlink
header.
====================
If oct->fn_list.enable_io_queues() fails, no cleanup is executed, leading
to memory/resource leaks. To fix this issue, invoke
octeon_delete_instr_queue() before returning from the function.
Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement dummy region of size 32K and allow user to create snapshots
or random data using debugfs file trigger.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sync EEE init for RTL8168h with vendor driver and add two writes to
vendor-specific registers.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the Realtek PHY driver maps the vendor-specific EEE registers
to the standard MMD registers, we can remove all special handling and
use the generic functions phy_ethtool_get/set_eee.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
EEE-related registers on newer integrated PHY's have the standard
layout, but are accessible not via MMD but via vendor-specific
registers. Emulating the standard MMD registers allows to use the
generic functions for EEE control.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cited patch deleted ethtool flash device support, as ethtool core can
fallback into devlink flash callback. However, this is supported only if
there is a devlink port registered over the corresponding netdevice.
As mlx5e do not have devlink port support over native netdevice, it broke
the ability to flash device via ethtool.
This patch re-add the ethtool callback to avoid user functionality breakage
when trying to flash device via ethtool.
Fixes: 9c8bca2637 ("mlx5: Move firmware flash implementation to devlink")
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add a missing spinlock around XSKICOSQ usage at the activation stage,
because there is a race between a configuration change and the
application calling sendto().
Fixes: db05815b36 ("net/mlx5e: Add XSK zero-copy support")
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When the genphy driver binds to a swphy it will call
genphy_read_abilites that will try to read MII_ESTATUS if BMSR_ESTATEN
is set in MII_BMSR. So far this would read the default value 0xffff
and 1000FD and 1000HD are reported as supported just by chance.
Better add explicit support for emulating MII_ESTATUS.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Value of MII_CTRL1000 is needed only if LPA_1000MSFAIL is set.
Therefore move reading this register.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
quirk_reset_lenovo_thinkpad_50_nvgpu() resets NVIDIA GPUs to work around
an apparent BIOS defect. It previously used pci_reset_function(), and
the available method was a bus reset, which was fine because there was
only one function on the bus. After b516ea586d ("PCI: Enable NVIDIA
HDA controllers"), there are now two functions (the HDA controller and
the GPU itself) on the bus, so the reset fails.
Use pci_reset_bus() explicitly instead of pci_reset_function() since it's
OK to reset both devices.
[bhelgaas: commit log, add e0547c81bf]
Fixes: b516ea586d ("PCI: Enable NVIDIA HDA controllers")
Fixes: e0547c81bf ("PCI: Reset Lenovo ThinkPad P50 nvgpu at boot if necessary")
Link: https://lore.kernel.org/r/20190801220117.14952-1-lyude@redhat.com
Signed-off-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Ben Skeggs <bskeggs@redhat.com>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Daniel Drake <drake@endlessm.com>
Cc: Aaron Plattner <aplattner@nvidia.com>
Cc: Peter Wu <peter@lekensteyn.nl>
Cc: Ilia Mirkin <imirkin@alum.mit.edu>
Cc: Karol Herbst <kherbst@redhat.com>
Cc: Maik Freudenberg <hhfeuer@gmx.de>
Pull auxdisplay fixes from Miguel Ojeda:
"A few minor auxdisplay improvements:
- A couple of small header cleanups for charlcd (Masahiro Yamada)
- A trivial typo fix for the examples of cfag12864b (Masahiro Yamada)
- An Kconfig help text improvement for charlcd (Mans Rullgard)
- An error path fix for panel (zhengbin)"
* tag 'auxdisplay-for-linus-v5.3-rc5' of git://github.com/ojeda/linux:
auxdisplay: Fix a typo in cfag12864b-example.c
auxdisplay: charlcd: add include guard to charlcd.h
auxdisplay: charlcd: move charlcd.h to drivers/auxdisplay
auxdisplay: charlcd: add help text for backlight initial state
auxdisplay: panel: need to delete scan_timer when misc_register fails in panel_attach
Pull devicetree fixes from Rob Herring:
- Fix building DT binding examples for in tree builds
- Correct some refcounting in adjust_local_phandle_references()
- Update FSL FEC binding with deprecated properties
- Schema fix in stm32 pinctrl
- Fix typo in of_irq_parse_one docbook comment
* tag 'devicetree-fixes-for-5.3-3' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
of: irq: fix a trivial typo in a doc comment
dt-bindings: pinctrl: stm32: Fix 'st,syscfg' schema
dt-bindings: fec: explicitly mark deprecated properties
of: resolver: Add of_node_put() before return and break
dt-bindings: Fix generated example files getting added to schemas
