When the user issues a command with side effects, we will end up freezing
the namespace request queue when updating disk info (and the same for
the corresponding mpath disk node).
However, we are not freezing the mpath node request queue,
which means that mpath I/O can still come in and block on blk_queue_enter
(called from nvme_ns_head_make_request -> direct_make_request).
This is a deadlock, because blk_queue_enter will block until the inner
namespace request queue is unfroze, but that process is blocked because
the namespace revalidation is trying to update the mpath disk info
and freeze its request queue (which will never complete because
of the I/O that is blocked on blk_queue_enter).
Fix this by freezing all the subsystem nsheads request queues before
executing the passthru command. Given that these commands are infrequent
we should not worry about this temporary I/O freeze to keep things sane.
Here is the matching hang traces:
--
[ 374.465002] INFO: task systemd-udevd:17994 blocked for more than 122 seconds.
[ 374.472975] Not tainted 5.2.0-rc3-mpdebug+ #42
[ 374.478522] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 374.487274] systemd-udevd D 0 17994 1 0x00000000
[ 374.493407] Call Trace:
[ 374.496145] __schedule+0x2ef/0x620
[ 374.500047] schedule+0x38/0xa0
[ 374.503569] blk_queue_enter+0x139/0x220
[ 374.507959] ? remove_wait_queue+0x60/0x60
[ 374.512540] direct_make_request+0x60/0x130
[ 374.517219] nvme_ns_head_make_request+0x11d/0x420 [nvme_core]
[ 374.523740] ? generic_make_request_checks+0x307/0x6f0
[ 374.529484] generic_make_request+0x10d/0x2e0
[ 374.534356] submit_bio+0x75/0x140
[ 374.538163] ? guard_bio_eod+0x32/0xe0
[ 374.542361] submit_bh_wbc+0x171/0x1b0
[ 374.546553] block_read_full_page+0x1ed/0x330
[ 374.551426] ? check_disk_change+0x70/0x70
[ 374.556008] ? scan_shadow_nodes+0x30/0x30
[ 374.560588] blkdev_readpage+0x18/0x20
[ 374.564783] do_read_cache_page+0x301/0x860
[ 374.569463] ? blkdev_writepages+0x10/0x10
[ 374.574037] ? prep_new_page+0x88/0x130
[ 374.578329] ? get_page_from_freelist+0xa2f/0x1280
[ 374.583688] ? __alloc_pages_nodemask+0x179/0x320
[ 374.588947] read_cache_page+0x12/0x20
[ 374.593142] read_dev_sector+0x2d/0xd0
[ 374.597337] read_lba+0x104/0x1f0
[ 374.601046] find_valid_gpt+0xfa/0x720
[ 374.605243] ? string_nocheck+0x58/0x70
[ 374.609534] ? find_valid_gpt+0x720/0x720
[ 374.614016] efi_partition+0x89/0x430
[ 374.618113] ? string+0x48/0x60
[ 374.621632] ? snprintf+0x49/0x70
[ 374.625339] ? find_valid_gpt+0x720/0x720
[ 374.629828] check_partition+0x116/0x210
[ 374.634214] rescan_partitions+0xb6/0x360
[ 374.638699] __blkdev_reread_part+0x64/0x70
[ 374.643377] blkdev_reread_part+0x23/0x40
[ 374.647860] blkdev_ioctl+0x48c/0x990
[ 374.651956] block_ioctl+0x41/0x50
[ 374.655766] do_vfs_ioctl+0xa7/0x600
[ 374.659766] ? locks_lock_inode_wait+0xb1/0x150
[ 374.664832] ksys_ioctl+0x67/0x90
[ 374.668539] __x64_sys_ioctl+0x1a/0x20
[ 374.672732] do_syscall_64+0x5a/0x1c0
[ 374.676828] entry_SYSCALL_64_after_hwframe+0x44/0xa9
[ 374.738474] INFO: task nvmeadm:49141 blocked for more than 123 seconds.
[ 374.745871] Not tainted 5.2.0-rc3-mpdebug+ #42
[ 374.751419] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 374.760170] nvmeadm D 0 49141 36333 0x00004080
[ 374.766301] Call Trace:
[ 374.769038] __schedule+0x2ef/0x620
[ 374.772939] schedule+0x38/0xa0
[ 374.776452] blk_mq_freeze_queue_wait+0x59/0x100
[ 374.781614] ? remove_wait_queue+0x60/0x60
[ 374.786192] blk_mq_freeze_queue+0x1a/0x20
[ 374.790773] nvme_update_disk_info.isra.57+0x5f/0x350 [nvme_core]
[ 374.797582] ? nvme_identify_ns.isra.50+0x71/0xc0 [nvme_core]
[ 374.804006] __nvme_revalidate_disk+0xe5/0x110 [nvme_core]
[ 374.810139] nvme_revalidate_disk+0xa6/0x120 [nvme_core]
[ 374.816078] ? nvme_submit_user_cmd+0x11e/0x320 [nvme_core]
[ 374.822299] nvme_user_cmd+0x264/0x370 [nvme_core]
[ 374.827661] nvme_dev_ioctl+0x112/0x1d0 [nvme_core]
[ 374.833114] do_vfs_ioctl+0xa7/0x600
[ 374.837117] ? __audit_syscall_entry+0xdd/0x130
[ 374.842184] ksys_ioctl+0x67/0x90
[ 374.845891] __x64_sys_ioctl+0x1a/0x20
[ 374.850082] do_syscall_64+0x5a/0x1c0
[ 374.854178] entry_SYSCALL_64_after_hwframe+0x44/0xa9
--
Reported-by: James Puthukattukaran <james.puthukattukaran@oracle.com>
Tested-by: James Puthukattukaran <james.puthukattukaran@oracle.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Presently, nvmet_file_flush() always returns a call to
errno_to_nvme_status() but that helper doesn't take into account the
case when errno=0. So nvmet_file_flush() always returns an error code.
All other callers of errno_to_nvme_status() check for success before
calling it.
To fix this, ensure errno_to_nvme_status() returns success if the
errno is zero. This should prevent future mistakes like this from
happening.
Fixes: c6aa3542e0 ("nvmet: add error log support for file backend")
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
After calling nvme_loop_delete_ctrl(), the controllers will not
yet be deleted because nvme_delete_ctrl() only schedules work
to do the delete.
This means a race can occur if a port is removed but there
are still active controllers trying to access that memory.
To fix this, flush the nvme_delete_wq before returning from
nvme_loop_remove_port() so that any controllers that might
be in the process of being deleted won't access a freed port.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Reviewed-by : Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
When a port is removed through configfs, any connected controllers
are still active and can still send commands. This causes a
use-after-free bug which is detected by KASAN for any admin command
that dereferences req->port (like in nvmet_execute_identify_ctrl).
To fix this, disconnect all active controllers when a subsystem is
removed from a port. This ensures there are no active controllers
when the port is eventually removed.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Reviewed-by : Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
In phy_led_trigger_change_speed(), there is an if statement on line 48
to check whether phy->last_triggered is NULL:
if (!phy->last_triggered)
When phy->last_triggered is NULL, it is used on line 52:
led_trigger_event(&phy->last_triggered->trigger, LED_OFF);
Thus, a possible null-pointer dereference may occur.
To fix this bug, led_trigger_event(&phy->last_triggered->trigger,
LED_OFF) is called when phy->last_triggered is not NULL.
This bug is found by a static analysis tool STCheck written by
the OSLAB group in Tsinghua University.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Saeed Mahameed says:
====================
mlx5-updates-2019-07-29
This series includes updates to mlx5 driver,
1) Simplifications, cleanup and warning prints improvements
2) From Vlad Buslov:
Refactor mlx5 tc flow handling for unlocked execution (Part 1)
Currently, all cls API hardware offloads driver callbacks require caller
to hold rtnl lock when calling them. Cls API has already been updated to
update software filters in parallel (on classifiers that support
unlocked execution), however hardware offloads code still obtains rtnl
lock before calling driver tc callbacks. This set implements partial
support for unlocked execution that is leveraged by follow up
refactorings in specific mlx5 tc subsystems and patch to cls API that
implements API that allows drivers to register their callbacks as
rtnl-unlocked.
In mlx5 tc code mlx5e_tc_flow is the main structure that is used to
represent tc filter. Currently, code the structure itself and its
handlers in both tc and eswitch layers do not implement any kind of
synchronizations and assume external global synchronization provided by
rtnl lock instead. Implement following changes to remove dependency on
rtnl lock in flow handling code that are intended to be used a
groundwork for following changes to provide fully rtnl-independent mlx5
tc:
- Extend struct mlx5e_tc_flow with atomic reference counter and rcu to
allow concurrent access from multiple tc and neigh update workqueue
instances without introducing any additional locks specific to the
structure. Its 'flags' field type is changed to atomic bitmask ops which
is necessary for tc to interact with other concurrent tc instances or
concurrent neigh update that need to skip flows that are not fully
initialized (new INIT_DONE flow flag) and can change the flags
according to neighbor state (flipping OFFLOADED flag).
- Protect unready flows list by new uplink_priv->unready_flows_lock
mutex.
- Convert calls to netdev APIs that require rtnl lock in flow handling
code to their rcu counterparts.
- Modify eswitch code that is called from tc layer and assume implicit
external synchronization to be concurrency safe: change
esw->offloads.num_flows type to atomic integer and re-arrange
esw->state_lock usage to protect additional data.
Some of approaches to synchronizations presented in this patch set are
quite complicated (lockless concurrent usage of data structures with rcu
and reference counting, using fine-grained locking when necessary, retry
mechanisms to handle concurrent insertion of another instance of data
structure with same key, etc.). This is necessary to allow calling the
firmware in parallel in most cases, which is the main motivation of this
change since firmware calls are mach heavier operation than atomic
operations, multitude of locks and potential multiple retries during
concurrent accesses to same elements.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
As a result of refactoring of VF VSIs interrupts code, there is no
need to track its configuration status again with ICE_VF_STATE_CFG_INTR
flag - In fact, it is not being checked anywhere in the code right now, so
this patch removes the dead code as applicable to the flag.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This flag is not needed and is called every time we re-enable interrupts
in the hotpath so remove it. Also remove ice_vsi_req_irq() because it
was a wrapper function for ice_vsi_req_irq_msix() whose sole purpose was
checking the ICE_FLAG_MSIX_ENA flag.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since Tx rings are being managed by FW/NVM, Tx rings might have not been
set up or driver had already wiped them off - In that case, call to
disable LAN Tx queue is being returned as not in existence. This patch
makes sure we don't return unnecessary error for such scenario.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently if the call to ice_alloc_mapped_page() fails we jump to the
no_buf label, possibly call ice_release_rx_desc(), and return true
indicating that there is more work to do. In the success case we just
fall out of the while loop, possibly call ice_alloc_mapped_page(), and
return false saying we exhausted cleaned_count. This flow can be
improved by breaking if ice_alloc_mapped_page() fails and then the flow
outside of the while loop is the same for the failure and success case.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently we are not reporting dropped counts at the port level to
ethtool or netlink. This was found when debugging Rx dropped issues
and the total packets sent did not equal the total packets received
minus the rx_dropped, which was very confusing. To determine dropped
counts at the port level we need to read the PRTRPB_RDPC register.
To fix reporting we will store the dropped counts in the PF's
rx_discards. This will be reported to netlink by storing it in the
PF VSI's rx_missed_errors signaling that the receiver missed the
packet. Also, we will report this to ethtool in the rx_dropped.nic
field.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In case there is a request from a VF to change its number of queues, and
the request was successful, we need to update number of queues
configured on the VF before updating corresponding VSI for that VF,
especially LAN Tx queue tree and TC update, otherwise, we would continued
to use old value of vf->num_vf_qs for allocated Tx/Rx queues...
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch uses allocated number of Tx queues per VSI to set up its
scheduling tree instead of using total number of available Tx queues.
Only PF VSIs have total number of allocated Tx queues equal to number
of available Tx queues, other VSIs have different number of queues
configured.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently we bump the Rx tail and release/give buffers to hardware every
16 descriptors. This causes us to bump Rx tail up to 4 times per
napi_poll call. Also we are always bumping tail on an odd index and this
is a problem because hardware ignores the lower 3 bits in the QRX_TAIL
register. This is making it so hardware sees tail bumps only every 8
descriptors. Instead lets only bump Rx tail once per napi_poll if
the value aligns with hardware's expectations of the lower 3 bits being
cleared. Also only release/give Rx buffers once per napi_poll call.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Certain ttys operations (pty_unix98_ops) lack tiocmget() and tiocmset()
functions which are called by the certain HCI UART protocols (hci_ath,
hci_bcm, hci_intel, hci_mrvl, hci_qca) via hci_uart_set_flow_control()
or directly. This leads to an execution at NULL and can be triggered by
an unprivileged user. Fix this by adding a helper function and a check
for the missing tty operations in the protocols code.
This fixes CVE-2019-10207. The Fixes: lines list commits where calls to
tiocm[gs]et() or hci_uart_set_flow_control() were added to the HCI UART
protocols.
Link: https://syzkaller.appspot.com/bug?id=1b42faa2848963564a5b1b7f8c837ea7b55ffa50
Reported-by: syzbot+79337b501d6aa974d0f6@syzkaller.appspotmail.com
Cc: stable@vger.kernel.org # v2.6.36+
Fixes: b3190df628 ("Bluetooth: Support for Atheros AR300x serial chip")
Fixes: 118612fb91 ("Bluetooth: hci_bcm: Add suspend/resume PM functions")
Fixes: ff2895592f ("Bluetooth: hci_intel: Add Intel baudrate configuration support")
Fixes: 162f812f23 ("Bluetooth: hci_uart: Add Marvell support")
Fixes: fa9ad876b8 ("Bluetooth: hci_qca: Add support for Qualcomm Bluetooth chip wcn3990")
Signed-off-by: Vladis Dronov <vdronov@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Reviewed-by: Yu-Chen, Cho <acho@suse.com>
Tested-by: Yu-Chen, Cho <acho@suse.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds code to clear VFs enable status until reset is completed,
and Tx/Rx rings are setup. Without this patch, the code flow request Tx
queues to be disabled after reset, especially PFR - where VF VSI Tx rings
have already been wiped off in the NVM and result to adminq error based on
the call to disable Tx LAN queue in ice_reset_all_vfs function call.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The firmware reports an error when trying to configure a port with no
media. Instead of always configuring the port, check for media before
attempting to configure it. In the absence of media, turn off link and
poll for media to become available before re-enabling link.
Move ice_force_phys_link_state() up to avoid forward declaration.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The ice_init_all_ctrlq and ice_shutdown_all_ctrlq functions create and
destroy the locks used to protect the send and receive process of each
control queue.
This is problematic, as the driver may use these functions to shutdown
and re-initialize the control queues at run time. For example, it may do
this in response to a device reset.
If the driver failed to recover from a reset, it might leave the control
queues offline. In this case, the locks will no longer be initialized.
A later call to ice_sq_send_cmd will then attempt to acquire a lock that
has been destroyed.
It is incorrect behavior to access a lock that has been destroyed.
Indeed, ice_aq_send_cmd already tries to avoid accessing an offline
control queue, but the check occurs inside the lock.
The root of the problem is that the locks are destroyed at run time.
Modify ice_init_all_ctrlq and ice_shutdown_all_ctrlq such that they no
longer create or destroy the locks.
Introduce new functions, ice_create_all_ctrlq and ice_destroy_all_ctrlq.
Call these functions in ice_init_hw and ice_deinit_hw.
Now, the control queue locks will remain valid for the life of the
driver, and will not be destroyed until the driver unloads.
This also allows removing a duplicate check of the sq.count and
rq.count values when shutting down the controlqs. The ice_shutdown_ctrlq
function already checks this value under the lock. Previously
commit dec64ff10e ("ice: use [sr]q.count when checking if queue is
initialized") needed this check to happen outside the lock, because it
prevented duplicate attempts at destroying the locks.
The driver may now safely use ice_init_all_ctrlq and
ice_shutdown_all_ctrlq while handling reset events, without causing the
locks to be invalid.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently we are always setting prefena to 0. This is causing the
hardware to only fetch descriptors when there are none free in the cache
for a received packet instead of prefetching when it has used the last
descriptor regardless of incoming packets. Fix this by allowing the
hardware to prefetch Rx descriptors.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When interrupt tracking was refactored, during rebuild, the call to
ice_vsi_setup_vector_base() was inadvertently removed from the PF VSI
instead of being removed from the VF VSI. During reset, the failure to
properly setup the vector base generates a call trace. Correct this so
that resets/rebuilds properly complete.
Fixes: cbe66bfee6 ("ice: Refactor interrupt tracking")
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently, ice_stat_update32 and ice_stat_update40 will limit the
value of the software statistic to 32 or 40 bits wide, depending on
which register is being read.
This means that if a driver is running for a long time, the displayed
software register values will roll over to zero at 40 bits or 32 bits.
This occurs because the functions directly assign the difference between
the previous value and current value of the hardware statistic.
Instead, add this value to the current software statistic, and then
update the previous value.
In this way, each time ice_stat_update40 or ice_stat_update32 are
called, they will increment the software tracking value by the
difference of the hardware register from its last read. The software
tracking value will correctly count up until it overflows a u64.
The only requirement is that the ice_stat_update functions be called at
least once each time the hardware register overflows.
While we're fixing ice_stat_update40, modify it to use rd64 instead of
two calls to rd32. Additionally, drop the now unnecessary hireg
function parameter.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add support for reporting link partner advertising when
ETHTOOL_GLINKSETTINGS defined. Get pause param reports the Tx/Rx
pause configured, and then ethtool issues ETHTOOL_GSET ioctl and
ice_get_settings_link_up reports the negotiated Tx/Rx pause. Negotiated
pause frame report per IEEE 802.3-2005 table 288-3.
$ ethtool --show-pause ens6f0
Pause parameters for ens6f0:
Autonegotiate: on
RX: on
TX: on
RX negotiated: on
TX negotiated: on
$ ethtool ens6f0
Settings for ens6f0:
Supported ports: [ FIBRE ]
Supported link modes: 25000baseCR/Full
Supported pause frame use: Symmetric
Supports auto-negotiation: Yes
Supported FEC modes: None BaseR RS
Advertised link modes: 25000baseCR/Full
Advertised pause frame use: Symmetric Receive-only
Advertised auto-negotiation: Yes
Advertised FEC modes: None BaseR RS
Link partner advertised link modes: Not reported
Link partner advertised pause frame use: Symmetric
Link partner advertised auto-negotiation: Yes
Link partner advertised FEC modes: Not reported
Speed: 25000Mb/s
Duplex: Full
Port: Direct Attach Copper
PHYAD: 0
Transceiver: internal
Auto-negotiation: on
Supports Wake-on: g
Wake-on: g
Current message level: 0x00000007 (7)
drv probe link
Link detected: yes
When ETHTOOL_GLINKSETTINGS is not defined, get pause param reports the
negotiated Tx/Rx pause.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Pull IPMI fix from Corey Minyard:
"One necessary fix for an uninitialized variable in the new IPMB driver.
Nothing else has come in besides things that need to wait until later"
* tag 'for-linus-5.3-2' of git://github.com/cminyard/linux-ipmi:
Fix uninitialized variable in ipmb_dev_int.c
While do COMPILE_TEST build without CONFIG_NETDEVICES,
we get Kconfig warning:
WARNING: unmet direct dependencies detected for PHYLIB
Depends on [n]: NETDEVICES [=n]
Selected by [y]:
- OCTEON_ETHERNET [=y] && STAGING [=y] && (CAVIUM_OCTEON_SOC && NETDEVICES [=n] || COMPILE_TEST [=y])
Reported-by: Hulk Robot <hulkci@huawei.com>
Reported-by: Mark Brown <broonie@kernel.org>
Fixes: 171a9bae68 ("staging/octeon: Allow test build on !MIPS")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johannes Berg says:
====================
We have a reasonably large number of changes:
* lots more HE (802.11ax) support, particularly things
relevant for the the AP side, but also mesh support
* debugfs cleanups from Greg
* some more work on extended key ID
* start using genl parallel_ops, as preparation for
weaning ourselves off RTNL and getting parallelism
* various other changes all over
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Since linux 4.9 it is not possible to use buffers on the stack for DMA transfers.
During usb probe the driver crashes with "transfer buffer is on stack" message.
This fix k-allocates a buffer to be used on "read_reg_atomic", which is a macro
that calls "usb_control_msg" under the hood.
Kernel 4.19 backtrace:
usb_hcd_submit_urb+0x3e5/0x900
? sched_clock+0x9/0x10
? log_store+0x203/0x270
? get_random_u32+0x6f/0x90
? cache_alloc_refill+0x784/0x8a0
usb_submit_urb+0x3b4/0x550
usb_start_wait_urb+0x4e/0xd0
usb_control_msg+0xb8/0x120
hfcsusb_probe+0x6bc/0xb40 [hfcsusb]
usb_probe_interface+0xc2/0x260
really_probe+0x176/0x280
driver_probe_device+0x49/0x130
__driver_attach+0xa9/0xb0
? driver_probe_device+0x130/0x130
bus_for_each_dev+0x5a/0x90
driver_attach+0x14/0x20
? driver_probe_device+0x130/0x130
bus_add_driver+0x157/0x1e0
driver_register+0x51/0xe0
usb_register_driver+0x5d/0x120
? 0xf81ed000
hfcsusb_drv_init+0x17/0x1000 [hfcsusb]
do_one_initcall+0x44/0x190
? free_unref_page_commit+0x6a/0xd0
do_init_module+0x46/0x1c0
load_module+0x1dc1/0x2400
sys_init_module+0xed/0x120
do_fast_syscall_32+0x7a/0x200
entry_SYSENTER_32+0x6b/0xbe
Signed-off-by: Juliana Rodrigueiro <juliana.rodrigueiro@intra2net.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The whole block is protected by "if NET_VENDOR_MEDIATEK", so there is
no need for individual driver config symbols to duplicate this
dependency.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johannes Berg says:
====================
Just a few fixes:
* revert NETIF_F_LLTX usage as it caused problems
* avoid warning on WMM parameters from AP that are too short
* fix possible null-ptr dereference in hwsim
* fix interface combinations with 4-addr and crypto control
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to use GFP_ATOMIC here, GFP_KERNEL should be enough.
The 'kcalloc()' just a few lines above, already uses GFP_KERNEL.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
A few lines above, we have:
tx_size = BIT(tx->order);
So use 'tx_size' directly to be consistent with the way 'rx->descs_cpu' and
'rx->descs_dma' are computed below.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no good reason to use GFP_ATOMIC here. Other memory allocations
are performed with GFP_KERNEL (see other 'dma_alloc_coherent()' below and
'kzalloc()' in 'et131x_rx_dma_memory_alloc()')
Use GFP_KERNEL which should be enough.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit e891ce1dd2 ("mlxsw: spectrum_buffers: Reduce pool size on
Spectrum-2"), pool size was reduced to mitigate a problem in port buffer
usage of ports split four ways. It turns out that this work around does not
solve the issue, and a further reduction is required.
Thus reduce the size of pool 0 by another 2.7 MiB, and round down to the
whole number of cells.
Fixes: e891ce1dd2 ("mlxsw: spectrum_buffers: Reduce pool size on Spectrum-2")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of sp2 pci driver registration fail, fix the error path to
start with sp1 pci driver unregister.
Fixes: c3ab435466 ("mlxsw: spectrum: Extend to support Spectrum-2 ASIC")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit abbbdf1249 ("replace kill_bdev() with __invalidate_device()")
once did this, but 29eaadc036 ("nbd: stop using the bdev everywhere")
resurrected kill_bdev() and it has been there since then. So buffer_head
mappings still get killed on a server disconnection, and we can still
hit the BUG_ON on a filesystem on the top of the nbd device.
EXT4-fs (nbd0): mounted filesystem with ordered data mode. Opts: (null)
block nbd0: Receive control failed (result -32)
block nbd0: shutting down sockets
print_req_error: I/O error, dev nbd0, sector 66264 flags 3000
EXT4-fs warning (device nbd0): htree_dirblock_to_tree:979: inode #2: lblock 0: comm ls: error -5 reading directory block
print_req_error: I/O error, dev nbd0, sector 2264 flags 3000
EXT4-fs error (device nbd0): __ext4_get_inode_loc:4690: inode #2: block 283: comm ls: unable to read itable block
EXT4-fs error (device nbd0) in ext4_reserve_inode_write:5894: IO failure
------------[ cut here ]------------
kernel BUG at fs/buffer.c:3057!
invalid opcode: 0000 [#1] SMP PTI
CPU: 7 PID: 40045 Comm: jbd2/nbd0-8 Not tainted 5.1.0-rc3+ #4
Hardware name: Amazon EC2 m5.12xlarge/, BIOS 1.0 10/16/2017
RIP: 0010:submit_bh_wbc+0x18b/0x190
...
Call Trace:
jbd2_write_superblock+0xf1/0x230 [jbd2]
? account_entity_enqueue+0xc5/0xf0
jbd2_journal_update_sb_log_tail+0x94/0xe0 [jbd2]
jbd2_journal_commit_transaction+0x12f/0x1d20 [jbd2]
? __switch_to_asm+0x40/0x70
...
? lock_timer_base+0x67/0x80
kjournald2+0x121/0x360 [jbd2]
? remove_wait_queue+0x60/0x60
kthread+0xf8/0x130
? commit_timeout+0x10/0x10 [jbd2]
? kthread_bind+0x10/0x10
ret_from_fork+0x35/0x40
With __invalidate_device(), I no longer hit the BUG_ON with sync or
unmount on the disconnected device.
Fixes: 29eaadc036 ("nbd: stop using the bdev everywhere")
Cc: linux-block@vger.kernel.org
Cc: Ratna Manoj Bolla <manoj.br@gmail.com>
Cc: nbd@other.debian.org
Cc: stable@vger.kernel.org
Cc: David Woodhouse <dwmw@amazon.com>
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Munehisa Kamata <kamatam@amazon.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Retrieving PHYs can defer the probe, do not spawn an error when
-EPROBE_DEFER is returned, it is normal behavior.
Fixes: b1a9edbda0 ("ata: libahci: allow to use multiple PHYs")
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
If applespi is enabled, but LEDs class support is not, the build fails:
drivers/input/keyboard/applespi.o: In function `applespi_probe':
applespi.c:(.text+0x1fcd): undefined reference to `devm_led_classdev_register_ext'
Add "depends on LEDS_CLASS" to the Konfig
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: 038b1a05ea ("Input: add Apple SPI keyboard and trackpad driver")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We have a lot of fixes, most of them are also applicable to stable.
Notably:
* fix use-after-free issues
* fix DMA mapping API usage errors
* fix frame drop occurring due to reorder buffer handling in
RSS in certain conditions
* fix rate scale locking issues
* disable TX A-MSDU on older NICs as it causes problems and was
never supposed to be supported
* new PCI IDs
* GEO_TX_POWER_LIMIT API issue that many people were hitting
Mark switch cases where we are expecting to fall through.
This patch fixes the following warning (Building: powerpc):
drivers/macintosh/smu.c: In function 'smu_queue_i2c':
drivers/macintosh/smu.c:854:21: warning: this statement may fall through [-Wimplicit-fallthrough=]
cmd->info.devaddr &= 0xfe;
~~~~~~~~~~~~~~~~~~^~~~~~~
drivers/macintosh/smu.c:855:2: note: here
case SMU_I2C_TRANSFER_STDSUB:
^~~~
Fixes: 0365ba7fb1 ("[PATCH] ppc64: SMU driver update & i2c support")
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190730143704.060a2606@canb.auug.org.au
No VCN DPM bit check as that's different from VCN PG. Also
no extra check for possible double enablement/disablement
as that's already done by VCN.
v2: check return value of smu_feature_set_enabled
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Kenneth Feng <kenneth.feng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
