The variable rc is being initialized with a value that is never
read and it is being updated later with a new value that is returned.
The variable is redundant and can be replaced with a return 0 as
there are no other return points in this function.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The variable ret is being initialized with a value that is never
read and it is being updated later with a new value. The
initialization is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The WiFi tx power of RTL8723BU is extremely low after booting. So
the WiFi scan gives very limited AP list and it always fails to
connect to the selected AP. This module only supports 1x1 antenna
and the antenna is switched to bluetooth due to some incorrect
register settings.
Compare with the vendor driver https://github.com/lwfinger/rtl8723bu,
we realized that the 8723bu's enable_rf() does the same thing as
rtw_btcoex_HAL_Initialize() in vendor driver. And it by default
sets the antenna path to BTC_ANT_PATH_BT which we verified it's
the cause of the wifi weak tx power. The vendor driver will set
the antenna path to BTC_ANT_PATH_PTA in the consequent btcoexist
mechanism, by the function halbtc8723b1ant_PsTdma.
This commit hand over the antenna control to PTA(Packet Traffic
Arbitration), which compares the weight of bluetooth/wifi traffic
then determine whether to continue current wifi traffic or not.
After PTA take control, The wifi signal will be back to normal and
the bluetooth scan can also work at the same time. However, the
btcoexist still needs to be handled under different circumstances.
If there's a BT connection established, the wifi still fails to
connect until BT disconnected.
Signed-off-by: Chris Chiu <chiu@endlessm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In contrast to the TX path, there is no need to separately read the transfer
status from the device after receiving RX data. Consequently, there is no
real STATUS_PENDING RX processing queue entry state.
Remove the unnecessary ENTRY_DATA_STATUS_PENDING flag checks from the RX path.
Also remove the misleading comment about reading RX status from device.
Suggested-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Soeren Moch <smoch@web.de>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Explicitly return constants instead of variable (and rely on
it to be explicitly initialized), if the value is supposed
to be fixed anyways. Align it with the rest of the driver,
which does it the same way.
Signed-off-by: Enrico Weigelt <info@metux.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This avoids a warning when building with -Wimplicit-fallthrough.
Fixes: 883a2a80f7 ("Input: elantech - enable SMBus on new (2018+) systems")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
When closing the CAN device while tx skbs are inflight, echo skb could
be released twice. By calling close_candev() before unlinking all
pending tx urbs, then the internal echo_skb[] array is fully and
correctly cleared before the USB write callback and, therefore,
can_get_echo_skb() are called, for each aborted URB.
Fixes: bb4785551f ("can: usb: PEAK-System Technik USB adapters driver core")
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
To enter stop mode, the CPU should manually assert a global Stop Mode
request and check the acknowledgment asserted by FlexCAN. The CPU must
only consider the FlexCAN in stop mode when both request and
acknowledgment conditions are satisfied.
Fixes: de3578c198 ("can: flexcan: add self wakeup support")
Reported-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v5.0
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The gpr_np variable is still being used in dev_dbg() after the
of_node_put() call, which may result in use-after-free.
Fixes: de3578c198 ("can: flexcan: add self wakeup support")
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
Cc: linux-stable <stable@vger.kernel.org> # >= v5.0
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
add error check when workqueue alloc failed, and remove redundant code
to make it clear.
Fixes: e0000163e3 ("can: Driver for the Microchip MCP251x SPI CAN controllers")
Signed-off-by: Weitao Hou <houweitaoo@gmail.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Tested-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
We have observed rcar_canfd driver entering IRQ storm under high load,
with following scenario:
- rcar_canfd_global_interrupt() in entered due to Rx available,
- napi_schedule_prep() is called, and sets NAPIF_STATE_SCHED in state
- Rx fifo interrupts are masked,
- rcar_canfd_global_interrupt() is entered again, this time due to
error interrupt (e.g. due to overflow),
- since scheduled napi poller has not yet executed, condition for calling
napi_schedule_prep() from rcar_canfd_global_interrupt() remains true,
thus napi_schedule_prep() gets called and sets NAPIF_STATE_MISSED flag
in state,
- later, napi poller function rcar_canfd_rx_poll() gets executed, and
calls napi_complete_done(),
- due to NAPIF_STATE_MISSED flag in state, this call does not clear
NAPIF_STATE_SCHED flag from state,
- on return from napi_complete_done(), rcar_canfd_rx_poll() unmasks Rx
interrutps,
- Rx interrupt happens, rcar_canfd_global_interrupt() gets called
and calls napi_schedule_prep(),
- since NAPIF_STATE_SCHED is set in state at this time, this call
returns false,
- due to that false return, rcar_canfd_global_interrupt() returns
without masking Rx interrupt
- and this results into IRQ storm: unmasked Rx interrupt happens again
and again is misprocessed in the same way.
This patch fixes that scenario by unmasking Rx interrupts only when
napi_complete_done() returns true, which means it has cleared
NAPIF_STATE_SCHED in state.
Fixes: dd3bd23eb4 ("can: rcar_canfd: Add Renesas R-Car CAN FD driver")
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
CONFIG_CAN_LEDS is deprecated. When trying to use the generic netdev
trigger as suggested, there's a small inconsistency with the link
property: The LED is on initially, stays on when the device is brought
up, and then turns off (as expected) when the device is brought down.
Make sure the LED always reflects the state of the CAN device.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
As already mentioned in [1] and included in [2], there is an off by one
issue since the high bank is already enabled when the _next_ mailbox to
be read has index 12, so the mailbox being read was 13. The message can
therefore go into mailbox 31 and the driver will be repolled until the
mailbox 12 eventually receives a msg. Or the message might end up in the
12th mailbox, but then it would become disabled after reading it and only
be enabled again in the next "round" after mailbox 13 was read, which can
cause out of order messages, since the lower priority mailboxes can
accept messages in the meantime.
As mentioned in [3] there is a hardware race condition when changing the
CANME register while messages are being received. Even when including a
busy poll on reception, like in [2] there are still overflows and out of
order messages at times, but less then without the busy loop polling.
Unlike what the patch suggests, the polling time is not in the microsecond
range, but takes as long as a current CAN bus reception needs to finish,
so typically more in the fraction of millisecond range. Since the timeout
is in jiffies it won't timeout.
Even with these additional fixes the driver is still not able to provide a
proper FIFO which doesn't drop packages. So change the driver to use
rx-offload and base order on timestamp instead of message box numbers. As
a side affect, this also fixes [4] and [5].
Before this change messages with a single byte counter were dropped /
received out of order at a bitrate of 250kbit/s on an am3517. With this
patch that no longer occurs up to and including 1Mbit/s.
[1] https://linux-can.vger.kernel.narkive.com/zgO9inVi/patch-can-ti-hecc-fix-rx-wrong-sequence-issue#post6
[2] http://arago-project.org/git/projects/?p=linux-omap3.git;a=commit;h=02346892777f07245de4d5af692513ebd852dcb2
[3] https://linux-can.vger.kernel.narkive.com/zgO9inVi/patch-can-ti-hecc-fix-rx-wrong-sequence-issue#post5
[4] https://patchwork.ozlabs.org/patch/895956/
[5] https://www.spinics.net/lists/netdev/msg494971.html
Cc: Anant Gole <anantgole@ti.com>
Cc: AnilKumar Ch <anilkumar@ti.com>
Signed-off-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The flexcan controller can be forced as a wakeup source by
stating that explicitly in the device's .dts file using the
"wakeup-source" boolean property.
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Add support to select the clock source for CAN Protocol Engine (PE).
It's SoC Implementation dependent. Refer to RM for detailed definition
of each SoC. We select clock source 1 (peripheral clock) by default in
driver now, this patch adds support to parse the clock source from the DT.
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Flexcan will be disabled during suspend if no wakeup function required and
enabled after resume accordingly. During this period, we could explicitly
disable clocks.
Since PM is optional, the clock is enabled at probe to guarante the
clock is running when PM is not enabled in the kernel.
Implement Runtime PM which will:
1) Without CONFIG_PM, clock is running whether Flexcan up or down.
2) With CONFIG_PM, clock enabled while Flexcan up and disabled when
Flexcan down.
3) Disable clock when do system suspend and enable clock while system
resume.
4) Make Power Domain framework be able to shutdown the corresponding
power domain of this device.
Signed-off-by: Aisheng Dong <aisheng.dong@nxp.com>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
CANFD IP supports both CAN and CAN FD frames,
Existing driver supports only CAN frames, This patch
adds support for CAN FD frames.
Signed-off-by: Naga Sureshkumar Relli <naga.sureshkumar.relli@xilinx.com>
Signed-off-by: Appana Durga Kedareswara rao <appana.durga.rao@xilinx.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
To differentiate between different CAN IP's this patch adds
cantype enum variable in the xcan_devtype_data structure
Signed-off-by: Appana Durga Kedareswara rao <appana.durga.rao@xilinx.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
AXI CAN IP and CANPS IP supports tx fifo empty feature, this patch updates
the flags field for the same.
Signed-off-by: Appana Durga Kedareswara rao <appana.durga.rao@xilinx.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch fixes below kernel doc warnings
warning: Function parameter or member 'priv' not described in
'xcan_write_frame'
warning: Function parameter or member 'skb' not described in
'xcan_start_xmit_fifo'
warning: Function parameter or member 'ndev' not described in
'xcan_start_xmit_fifo'
warning: Function parameter or member 'skb' not described in
'xcan_start_xmit_mailbox'
warning: Function parameter or member 'ndev' not described in
'xcan_start_xmit_mailbox'
warning: Function parameter or member 'priv' not described in
'xcan_rx_fifo_get_next_frame'
Signed-off-by: Appana Durga Kedareswara rao <appana.durga.rao@xilinx.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch fixes below checkpatch warnings and checks in the driver.
CHECK: Alignment should match open parenthesis
+ void (*write_reg)(const struct xcan_priv *priv, enum xcan_reg reg,
+ u32 val);
CHECK: Alignment should match open parenthesis
+static void xcan_write_reg_le(const struct xcan_priv *priv, enum xcan_reg reg,
+ u32 val)
CHECK: Alignment should match open parenthesis
+static void xcan_write_reg_be(const struct xcan_priv *priv, enum xcan_reg reg,
+ u32 val)
CHECK: Alignment should match open parenthesis
+ netdev_dbg(ndev, "BRPR=0x%08x, BTR=0x%08x\n",
+ priv->read_reg(priv, XCAN_BRPR_OFFSET),
CHECK: Alignment should match open parenthesis
+ netdev_warn(ndev,
+ "timed out for correct mode\n");
CHECK: Alignment should match open parenthesis
+ netdev_dbg(ndev, "status:#x%08x\n",
+ priv->read_reg(priv, XCAN_SR_OFFSET));
CHECK: spaces preferred around that '-' (ctx:VxV)
+ (CAN_EFF_ID_BITS-CAN_SFF_ID_BITS)) <<
^
CHECK: Alignment should match open parenthesis
+ netdev_dbg(ndev, "%s: error status register:0x%x\n",
+ __func__, priv->read_reg(priv, XCAN_ESR_OFFSET));
WARNING: line over 80 characters
+ offset = XCAN_RXMSG_2_FRAME_OFFSET(fsr & XCAN_FSR_RI_MASK);
WARNING: line over 80 characters
+ offset = XCAN_RXMSG_FRAME_OFFSET(fsr & XCAN_FSR_RI_MASK);
WARNING: line over 80 characters
+ while ((isr & XCAN_IXR_TXOK_MASK) && !WARN_ON(++retries == 100)) {
WARNING: line over 80 characters
+ priv->write_reg(priv, XCAN_ICR_OFFSET, XCAN_IXR_TXOK_MASK);
CHECK: Alignment should match open parenthesis
+ netdev_err(ndev, "%s: pm_runtime_get failed(%d)\n",
+ __func__, ret);
CHECK: Alignment should match open parenthesis
+ ret = request_irq(ndev->irq, xcan_interrupt, priv->irq_flags,
+ ndev->name, ndev);
CHECK: Alignment should match open parenthesis
+static int xcan_get_berr_counter(const struct net_device *ndev,
+ struct can_berr_counter *bec)
CHECK: Alignment should match open parenthesis
+ netdev_err(ndev, "%s: pm_runtime_get failed(%d)\n",
+ __func__, ret);
CHECK: Please don't use multiple blank lines
+
+
CHECK: Alignment should match open parenthesis
+ netdev_err(ndev, "%s: pm_runtime_get failed(%d)\n",
+ __func__, ret);`
Signed-off-by: Appana Durga Kedareswara rao <appana.durga.rao@xilinx.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Add the TCAN4x5x SPI CAN driver.
This device uses the Bosch MCAN IP core along with a SPI interface map.
Register to the MCAN common core code to manage the MCAN IP.
This device has a special method to indicate a write/read operation on
the data payload.
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Rename the common m_can_priv class structure to m_can_classdev as this
is more descriptive.
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Acked-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Create a m_can platform framework that peripheral
devices can register to and use common code and register sets.
The peripheral devices may provide read/write and configuration
support of the IP.
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Acked-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
This patch fixes the following warnings:
drivers/net/can/peak_canfd/peak_pciefd_main.c:668:3: warning: this statement may fall through [-Wimplicit-fallthrough=]
drivers/net/can/spi/mcp251x.c:875:7: warning: this statement may fall through [-Wimplicit-fallthrough=]
drivers/net/can/usb/peak_usb/pcan_usb.c:422:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
drivers/net/can/at91_can.c:895:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
drivers/net/can/at91_can.c:953:15: warning: this statement may fall through [-Wimplicit-fallthrough=]
drivers/net/can/usb/peak_usb/pcan_usb.c: In function ‘pcan_usb_decode_error’:
drivers/net/can/usb/peak_usb/pcan_usb.c:422:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
if (n & PCAN_USB_ERROR_BUS_LIGHT) {
^
drivers/net/can/usb/peak_usb/pcan_usb.c:428:2: note: here
case CAN_STATE_ERROR_WARNING:
^~~~
Warning level 3 was used: -Wimplicit-fallthrough=3
This patch is part of the ongoing efforts to enabling
-Wimplicit-fallthrough.
Notice that in some cases spelling mistakes were fixed.
In other cases, the /* fall through */ comment is placed
at the bottom of the case statement, which is what GCC
is expecting to find.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> # for the at91_can.c
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch adds support for Kvaser PCIEcan devices. This includes
support for up to 4 CAN channels on a single card, depending on device.
Signed-off-by: Henning Colliander <henning.colliander@evidente.se>
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Signed-off-by: Christer Beskow <chbe@kvaser.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct foo {
int stuff;
void *entry[];
};
instance = alloc(sizeof(struct foo) + count * sizeof(void *));
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
instance = alloc(struct_size(instance, entry, count));
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch add support for Fintek PCIE to 2 CAN controller support
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
We are currently using a wrong register for dcan revision. Although
this is currently only used for detecting the dcan module, let's
fix it to avoid confusion.
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We have cases where there are no softreset bits like with am335x lcdc.
In that case ti,sysc-mask = <0> needs to be handled properly.
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
For some devices we can get the following warning on boot:
ti-sysc 48485200.target-module: sysc_disable_module: invalid midlemode
Fix this by treating SYSC_IDLE_FORCE like we do for the other bits
for idlemodes mask.
Fixes: d59b60564c ("bus: ti-sysc: Add generic enable/disable functions")
Cc: Roger Quadros <rogerq@ti.com>
Reviewed-by: Suman Anna <s-anna@ti.com>
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch sorts the drivers in the Makefile alphabetically and arranges
the Kconfig file accordingly.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Retrying immediately after we've received a 'transitioning' sense code is
pretty much pointless, we should always use a delay before retrying. So
ensure the default delay is applied before retrying.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Tested-by: Zhangguanghui <zhang.guanghui@h3c.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
#define relative to FCOE CTLR start with FCOE_CTLR, except
FCOE_CTRL_SOL_TOV.
This is likely a typo and CTRL should be CTLR here as well.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix sparse warnings:
drivers/scsi/megaraid/megaraid_sas_fusion.c:541:1: warning: symbol 'megasas_alloc_cmdlist_fusion' was not declared. Should it be static?
drivers/scsi/megaraid/megaraid_sas_fusion.c:580:1: warning: symbol 'megasas_alloc_request_fusion' was not declared. Should it be static?
drivers/scsi/megaraid/megaraid_sas_fusion.c:661:1: warning: symbol 'megasas_alloc_reply_fusion' was not declared. Should it be static?
drivers/scsi/megaraid/megaraid_sas_fusion.c:738:1: warning: symbol 'megasas_alloc_rdpq_fusion' was not declared. Should it be static?
drivers/scsi/megaraid/megaraid_sas_fusion.c:920:1: warning: symbol 'megasas_alloc_cmds_fusion' was not declared. Should it be static?
drivers/scsi/megaraid/megaraid_sas_fusion.c:1740:1: warning: symbol 'megasas_init_adapter_fusion' was not declared. Should it be static?
drivers/scsi/megaraid/megaraid_sas_fusion.c:1966:1: warning: symbol 'map_cmd_status' was not declared. Should it be static?
drivers/scsi/megaraid/megaraid_sas_fusion.c:2379:1: warning: symbol 'megasas_set_pd_lba' was not declared. Should it be static?
drivers/scsi/megaraid/megaraid_sas_fusion.c:2718:1: warning: symbol 'megasas_build_ldio_fusion' was not declared. Should it be static?
drivers/scsi/megaraid/megaraid_sas_fusion.c:3215:1: warning: symbol 'megasas_build_io_fusion' was not declared. Should it be static?
drivers/scsi/megaraid/megaraid_sas_fusion.c:3328:6: warning: symbol 'megasas_prepare_secondRaid1_IO' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
While loading fw crashdump in function fw_crash_buffer_show(), left bytes
in one dma chunk was not checked, if copying size over it, overflow access
will cause kernel panic.
Signed-off-by: Junxiao Bi <junxiao.bi@oracle.com>
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Replace the custom implementation with fwnode_get_mac_address,
which works on both DT and ACPI platforms.
While here, replace memcpy() by ether_addr_copy().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The onboard sky2 NIC on ASUS P6T WS PRO doesn't work after PM resume
due to the infamous IRQ problem. Disabling MSI works around it, so
let's add it to the blacklist.
Unfortunately the BIOS on the machine doesn't fill the standard
DMI_SYS_* entry, so we pick up DMI_BOARD_* entries instead.
BugLink: https://bugzilla.suse.com/show_bug.cgi?id=1142496
Reported-and-tested-by: Marcus Seyfarth <m.seyfarth@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recent additions to the kernel include a TC action module to manipulate
MPLS headers on packets. Such actions are available to offload via the
flow_offload intermediate representation API.
Modify the NFP driver to allow the offload of MPLS set actions to
firmware. Set actions update the outermost MPLS header. The offload
includes a mask to specify which fields should be set.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recent additions to the kernel include a TC action module to manipulate
MPLS headers on packets. Such actions are available to offload via the
flow_offload intermediate representation API.
Modify the NFP driver to allow the offload of MPLS pop actions to
firmware. The act_mpls TC module enforces that the next protocol is
supplied along with the pop action. Passing this to firmware allows it
to properly rebuild the underlying packet after the pop.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
