When getting port up down event (PUDE), change the PTP shaper
configuration based on hardware time stamping on/off and the port's
speed.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to get more accurate hardware time stamping, the driver needs to
enable PTP shaper on the port, for speeds lower than 40 Gbps.
Enable the PTP shaper on the port when the user turns on the hardware
time stamping, and disable it when the user turns off the hardware time
stamping.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set the PTP shaper parameters during the ptp_init(). For different
speeds, there are different parameters.
When the port's speed changes and PTP shaper is enabled, the firmware
changes the ETS shaper values according to the PTP shaper parameters for
this new speed.
The PTP shaper parameters array is left empty for now, will be filled in
a follow-up patch.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/ethernet/socionext/netsec.c: In function 'netsec_clean_tx_dring':
drivers/net/ethernet/socionext/netsec.c:637:15: warning:
variable 'pkts' set but not used [-Wunused-but-set-variable]
It is not used since commit ba2b232108 ("net: netsec: add XDP support")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove unneeded memset as alloc_etherdev is using kvzalloc which uses
__GFP_ZERO flag
Signed-off-by: Hariprasad Kelam <hariprasad.kelam@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several drivers cast a struct device pointer to a struct
platform_device pointer only to then call platform_get_drvdata().
To improve readability, these constructs can be simplified
by using dev_get_drvdata() directly.
Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several drivers cast a struct device pointer to a struct
platform_device pointer only to then call platform_get_drvdata().
To improve readability, these constructs can be simplified
by using dev_get_drvdata() directly.
Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch sets dax device 'DAXDEV_SYNC' flag if all the target
devices of device mapper support synchrononous DAX. If device
mapper consists of both synchronous and asynchronous dax devices,
we don't set 'DAXDEV_SYNC' flag.
'dm_table_supports_dax' is refactored to pass 'iterate_devices_fn'
as argument so that the callers can pass the appropriate functions.
Suggested-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Pankaj Gupta <pagupta@redhat.com>
Reviewed-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This patch adds 'DAXDEV_SYNC' flag which is set
for nd_region doing synchronous flush. This later
is used to disable MAP_SYNC functionality for
ext4 & xfs filesystem for devices don't support
synchronous flush.
Signed-off-by: Pankaj Gupta <pagupta@redhat.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This patch adds virtio-pmem driver for KVM guest.
Guest reads the persistent memory range information from
Qemu over VIRTIO and registers it on nvdimm_bus. It also
creates a nd_region object with the persistent memory
range information so that existing 'nvdimm/pmem' driver
can reserve this into system memory map. This way
'virtio-pmem' driver uses existing functionality of pmem
driver to register persistent memory compatible for DAX
capable filesystems.
This also provides function to perform guest flush over
VIRTIO from 'pmem' driver when userspace performs flush
on DAX memory range.
Signed-off-by: Pankaj Gupta <pagupta@redhat.com>
Reviewed-by: Yuval Shaia <yuval.shaia@oracle.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jakub Staron <jstaron@google.com>
Tested-by: Jakub Staron <jstaron@google.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This patch adds functionality to perform flush from guest
to host over VIRTIO. We are registering a callback based
on 'nd_region' type. virtio_pmem driver requires this special
flush function. For rest of the region types we are registering
existing flush function. Report error returned by host fsync
failure to userspace.
Signed-off-by: Pankaj Gupta <pagupta@redhat.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
There is no need for caller to know how uuid_t type is constructed. Thus,
whenever we use it the implementation details are not needed. Drop it for good.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This driver currently contains a repeated 500ms blocking delay call
which causes frequent major buffer underruns in PulseAudio. This patch
fixes this issue by replacing the blocking delay with a non-blocking
sleep call.
Signed-off-by: Yrjan Skrimstad <yrjan@skrimstad.net>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
kmemdup is introduced to duplicate a region of memory in a neat way.
Rather than kmalloc/kzalloc + memcpy, which the programmer needs to
write the size twice (sometimes lead to mistakes), kmemdup improves
readability, leads to smaller code and also reduce the chances of mistakes.
Suggestion to use kmemdup rather than using kmalloc/kzalloc + memcpy.
Reviewed-by: Christian König <Christian.Koenig@amd.com>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Allwinner NAND controllers can make use of DMA to enhance the I/O
throughput thanks to ECC pipelining. DMA handling with A23/A33 NAND IP
is a bit different than with the older SoCs, hence the introduction of
a new compatible to handle:
* the differences between register offsets,
* the burst length change from 4 to minimum 8,
* manage SRAM accesses through MBUS with extra configuration.
Fixes: c49836f05a ("mtd: rawnand: sunxi: Add A23/A33 DMA support")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
This reverts commit c49836f05a.
The commit is wrong and its approach actually does not work. Let's
revert it in order to add the feature with a clean patch.
Fixes: c49836f05a ("mtd: rawnand: sunxi: Add A23/A33 DMA support")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
I managed to break sorting in PCI ID defines in my last two patches:
commit 5cd1c56c42 ("i2c: i801: Add support for Intel Comet Lake")
commit 9be1485acc ("i2c: i801: Add support for Intel Elkhart Lake")
Fix them up.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Now that input_mt_report_slot_state() returns true if slot is active we no
longer need a temporary for the slot state.
Tested-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Define a MODULE_ALIAS() in the input sub-driver for max77650 so that
the appropriate module gets loaded together with the core mfd driver.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Fix leak (whose magnitude is the configuration file size) when the CRCs
match in mxt_update_cfg().
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Increasing the SATA/AHCI DMA TX/RX FIFOs (P0DMACR.TXTS and .RXTS, ie.
TX_TRANSACTION_SIZE and RX_TRANSACTION_SIZE) from default 0x0 each
to 0x3 each, gives a write performance boost of 120 MiB/s to 132 MiB/s
from lame 36 MiB/s to 45 MiB/s previously.
Read performance is above 200 MiB/s.
[tested on SSD using dd bs=4K/8K/12K/16K/20K/24K/32K: peak-perf at 12K]
Tested on the SBCs Banana Pi R1 (aka Lamobo R1) and Banana Pi M1 which
are based on the Allwinner A20 32bit-SoC (ARMv7-a / arm-linux-gnueabihf).
These devices are RaspberryPi-like small devices.
This problem of slow SATA write-speed with these small devices lasts
for about 7 years now (beginning with the A10 SoC). Many commentators
throughout the years wrongly assumed the slow write speed was a
hardware limitation. This patch finally solves the problem, which
in fact was just a hard-to-find software problem due to lack of
SATA/AHCI documentation by the SoC-maker Allwinner Technology.
Lists of the affected sunxi and other boards and SoCs with SATA using
the ahci_sunxi driver:
$ grep -i -e "^&ahci" arch/arm/boot/dts/sun*dts
and http://linux-sunxi.org/SATA#Devices_with_SATA_ports
See also http://linux-sunxi.org/Category:Devices_with_SATA_port
Tested-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Uenal Mutlu <um@mutluit.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The imx6 driver can be used on imx6sx without enabling support for
imx6q or imx7d but the "depends on" condition doesn't allow that.
Instead of making the condition even longer just make it depend on
"ARCH_MXC || COMPILE_TEST" instead.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Lucas Stach <l.stach@pengutronix.de>
Fix the return value check which testing the wrong variable
in imxfb_probe().
b.zolnierkie: please note that ->screen_base and ->screen_buffer
are equivalent (they are part of unnamed union in struct fb_info)
Fixes: 739a6439c2 ("video: fbdev: imxfb: fix sparse warnings about using incorrect types")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
In preparation to enabling -Wimplicit-fallthrough, mark switch
cases where we are expecting to fall through.
This patch fixes the following warnings:
drivers/video/fbdev/s3c-fb.c: In function ‘s3c_fb_blank’:
drivers/video/fbdev/s3c-fb.c:811:16: warning: this statement may fall through [-Wimplicit-fallthrough=]
sfb->enabled &= ~(1 << index);
~~~~~~~~~~~~~^~~~~~~~~~~~~~~~
drivers/video/fbdev/s3c-fb.c:814:2: note: here
case FB_BLANK_NORMAL:
^~~~
LD [M] drivers/staging/greybus/gb-light.o
CC [M] drivers/gpu/drm/nouveau/nvkm/subdev/secboot/gp10b.o
drivers/video/fbdev/s3c-fb.c: In function ‘s3c_fb_check_var’:
drivers/video/fbdev/s3c-fb.c:286:22: warning: this statement may fall through [-Wimplicit-fallthrough=]
var->transp.length = 1;
~~~~~~~~~~~~~~~~~~~^~~
drivers/video/fbdev/s3c-fb.c:288:2: note: here
case 18:
^~~~
drivers/video/fbdev/s3c-fb.c:314:22: warning: this statement may fall through [-Wimplicit-fallthrough=]
var->transp.offset = 24;
~~~~~~~~~~~~~~~~~~~^~~~
drivers/video/fbdev/s3c-fb.c:316:2: note: here
case 24:
^~~~
Warning level 3 was used: -Wimplicit-fallthrough=3
Notice that, in this particular case, the code comments are modified
in accordance with what GCC is expecting to find.
This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Kees Cook <keescook@chromium.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
When hw resetting, there is no response from hw when driver sending cmdq.
If driver still send cmdq to hw, the reset process may be blocked. So
reset flag should be set to intercept the cmdq command when driver
receiving "notify down" signal.
Signed-off-by: Lang Cheng <chenglang@huawei.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Currently, the depth of cq only supports 64K. According to the UM, the
depth of cq is up to 4M, Therefore the ba page size of cqe was modified to
support the maximum specification of cq depth.
Signed-off-by: Yangyang Li <liyangyang20@huawei.com>
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Hip06 reserve 12 qps, Hip08 reserve 8 qps. When the QP is released, the
chip model is not judged, and the Hip08 cannot release the qpn 8~12
Signed-off-by: Lang Cheng <chenglang@huawei.com>
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
It uses hns_roce_mtr_init in hns_roce_create_qp_common function. As a
result, it should use hns_roce_mtr_cleanup function for cleaning mtr when
destroying qp.
Fixes: 8d18ad83f1 ("RDMA/hns: Fix bug when wqe num is larger than 16K")
Signed-off-by: Xi Wang <wangxi11@huawei.com>
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
This patch adds the ability to return the hwstats of per-port default
counters (which can also be queried through sysfs nodes).
Signed-off-by: Mark Zhang <markz@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Provide an option to allow users to manually bind a qp with a counter
through RDMA netlink. Limit it to users with ADMIN capability only.
Signed-off-by: Mark Zhang <markz@mellanox.com>
Reviewed-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
In manual mode a QP is bound to a counter manually. If counter is not
specified then a new one will be allocated.
Manual mode is enabled when user binds a QP, and disabled when the last
manually bound QP is unbound.
When auto-mode is turned off and there are counters left, manual mode is
enabled so that the user is able to access these counters.
Signed-off-by: Mark Zhang <markz@mellanox.com>
Reviewed-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Since a QP can only be bound to one counter, then if it is bound to a
separate counter, for backward compatibility purpose, the statistic value
must be:
* stat of default counter
+ stat of all running allocated counters
+ stat of all deallocated counters (history stats)
Signed-off-by: Mark Zhang <markz@mellanox.com>
Reviewed-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
This patch adds the ability to return all available counters together with
their properties and hwstats.
Signed-off-by: Mark Zhang <markz@mellanox.com>
Reviewed-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Provide an option to enable/disable per-port counter auto mode through
RDMA netlink. Limit it to users with ADMIN capability only.
Signed-off-by: Mark Zhang <markz@mellanox.com>
Reviewed-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Add support for ib callbacks counter_bind_qp(), counter_unbind_qp() and
counter_dealloc().
Signed-off-by: Mark Zhang <markz@mellanox.com>
Reviewed-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Add counter set id as a parameter so that this API can be used for
querying any q counter.
Signed-off-by: Mark Zhang <markz@mellanox.com>
Reviewed-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Support bind a qp with counter. If counter is null then bind the qp to the
default counter. Different QP state has different operation:
- RESET: Set the counter field so that it will take effective during
RST2INIT change;
- RTS: Issue an RTS2RTS change to update the QP counter;
- Other: Set the counter field and mark the counter_pending flag, when QP
is moved to RTS state and this flag is set, then issue an RTS2RTS
modification to update the counter.
Signed-off-by: Mark Zhang <markz@mellanox.com>
Reviewed-by: Majd Dibbiny <majd@mellanox.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
