In general when the consumer of a regulator requests that the
regulator be disabled it no longer will be drawing much load from the
regulator--it should just be the leakage current and that should be
very close to 0.
Up to this point the regulator framework has continued to count a
consumer's load request for disabled regulators. This has led to code
patterns that look like this:
enable_my_thing():
regular_set_load(reg, load_uA)
regulator_enable(reg)
disable_my_thing():
regulator_disable(reg)
regulator_set_load(reg, 0)
Sometimes disable_my_thing() sets a nominal (<= 100 uA) load instead
of setting a 0 uA load. I will make the assertion that nearly all (if
not all) places where we set a nominal load of 100 uA or less we end
up with a result that is the same as if we had set a load of 0 uA.
Specifically:
- The whole point of setting the load is to help set the operating
mode of the regulator. Higher loads may need less efficient
operating modes.
- The only time this matters at all is if there is another consumer of
the regulator that wants the regulator on. If there are no other
consumers of the regulator then the regulator will turn off and we
don't care about the operating mode.
- If there's another consumer that actually wants the regulator on
then presumably it is requesting a load that makes our nominal
<= 100 uA load insignificant.
A quick survey of the existing callers to regulator_set_load() to see
how everyone uses it:
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
_FP_ROUND_ZERO is defined as 0 and used as a statemente in macro
_FP_ROUND. This generates "error: statement with no effect
[-Werror=unused-value]" from gcc. Defining _FP_ROUND_ZERO as (void)0 to
fix it.
This modification is quoted from glibc 'commit <In libc/:>
(8ed1e7d5894000c155acbd06f)'
Signed-off-by: Vincent Chen <vincentc@andestech.com>
Acked-by: Greentime Hu <greentime@andestech.com>
Signed-off-by: Greentime Hu <greentime@andestech.com>
This modification is quoted from glibc 'commit <
sysdeps/unix/sysv/linux/sparc/sparc64/dl-procinfo.c: Moved to>
(fe0b1e854ad32a69b260)'
Signed-off-by: Vincent Chen <vincentc@andestech.com>
Acked-by: Greentime Hu <greentime@andestech.com>
Signed-off-by: Greentime Hu <greentime@andestech.com>
Jonathan writes:
First set of new device support, features and cleanups for IIO in the 4.21 cycle
Along with the headline feature of 5 new drivers, we have the
substantial addition of auxilliary sensor support on the lsm6sdx
parts for ST. There has also been a good set of staging cleanup
in this period with more underway.
An ever increasing number of devices supported with just a new
ID which is a good sign that at least some manufacturers are
continuing to stabilise their interfaces.
New device support,
* ad7124
- New driver supporting Analog Devices' ad7124-4 and ad7124-8 parts
with the inevitable DT binding.
* ad7949
- New driver supporting Analog Devices' ad7949, AD7682 and AD7689 ADCs.
* rm3100
- New driver supporting PNIs RM3100 magnometer with bindings and
vendor prefix.
* ti-dac7311
- New driver supporting DAC7311, DAC6311 and DAC5311 TI DACs, with
DT bindings.
* vcnl5035
- New driver supporting the light sensor part of the VCNL4035, with
DT bindings
Features,
* bindings
- Add a generic ADC channel binding as we keep reinventing this
wheel.
* adc128s052
- Add IDs for additional pin compatible parts.
- Add APCI ID seen on E3940 UP squared boards.
* ad_sigma_delta
- Allow for custom data register overiding default.
* kxcjk1013
- Add KIOX0009 ACPI ID as seen on the Acer One 10.
* lsm6dsx
- Rework leading to...
- External sensor support using the built in I2C master.
- Initial support for a slave lis2mdl magnetometer.
* meson-saradc
- Add temperature sensor support and bindings.
* st_magn
- New ID for lsm9dsl_magn with bindings
- New ID for lis3de accelerometer
* tpl0102
- Add supprot for IIO_AVAIL_RANGE to report the range available
from this device to userspace and in kernel users.
Cleanups and minor fixes
* tools
- Allow outside specification of CFLAGS
* ad2s90
- Handle and spi_read error.
- Handle spi_setup failure
- Drop a pointless assignment.
- Prevent a potentail race by moving device registration to after
all other setup.
- Add missing scale attribute.
- Add a sanity check on channel type before trying to read it.
* ad2s1210
- Move to modern gpio descriptors.
- Drop a gpioin flag which made no sense as far as we can tell.
- Add dt table (bindings doc to follow when this is ready for
moving out of staging).
* ad5933
- Drop camel-case naming of ext_clk_hz.
- White space fixes.
* ad7150
- Local variable to shorten overly long line.
- Alignment and line break fixes.
* ad7280a
- Handle an error path that was previously ignored.
- Use crc8.h to build the crc table replacing custom code.
- Avoid unecessary cast.
- Power down the device if an error happens in probe
- Use devm routines to simplify probe and remove.
* ad7606
- Alignment fixes.
* ad7780
- This worked as long as by coincidence an uninitialized value
was 0. Lets not rely on that.
- Ensure gain update is only used with the ad778x chips that
actually support it.
- Tidy up pattern mask generation.
- Read regulator when scale is requested (which should be infrequent)
as it might have changed from initialization.
* ad7816
- Move to modern gpio descriptors
- Don't use a busy_pin for ad7818 as there isn't one.
- Ensure RD/WR and CONVST pins are outputs (previously they
were brought up as inputs which doesn't seem to make any sense)
- DT id table.
* adc128s052
- SPDX
* adt7316
- Alignment fix.
- Fix data reading. When using I2C the driver never actually
used the value read. This has been broken a very long time
hence no rush to fix it now + the driver is undergoing a lot
of cleanup.
- Sanity check that the i2c read didn't fail to actually read
anything.
* dpot-dac
- Mark a switch full through with slightly different text so that
gcc doesn't warn on it.
* gyro-adc
- Fix a wrong file in the MAINTAINERS entry and add binding doc to the
listed files.
* ina2xx
- Add some early returns to clarify error paths in switch.
* lsm6dsx
- MAINTAINERS entry.
* max11100
- SPDX
* max9611
- SPDX
* mcp4131
- use of_device_get_match_data in preference to spi_get_device_id
approach.
* rcar-adc
- SPDX
* sc27xx
- Add ADC conversion timeout support to avoid possible fault.
* ssp_sensors
- Don't free managed resources manually.
* st-magn
- Add a comment to avoid future confusion over when to use -magn
postfix (on multi chip in package parts)
- Add BDU register for LIS3MDL where it seems to have been missed.
* st-sensors
- Minor spelling, grammar etc fixes.
* tpl0102
- Use a pointer rather than an index of an array to improve conciseness.
* tag 'iio-for-4.21a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (80 commits)
Staging: iio: adt7316: Add an extra check for 'ret' equals to 0
Staging: iio: adt7316: Fix i2c data reading, set the data field
dt-bindings: iio: adc: Add docs for ad7124
iio: adc: Add ad7124 support
dt-bindings: iio: adc: Add common ADCs properties to a separate file
iio: ad_sigma_delta: Allow to provide custom data register address
staging: iio: ad7816: Add device tree table.
iio: imu: st_lsm6dsx: add entry in MAINTAINERS file
iio: potentiometer: mcp4131: use of_device_get_match_data()
staging: iio: adc: ad7280a: use devm_* APIs
staging: iio: adc: ad7280a: power down the device on error in probe
dt-bindings: iio: imu: st_lsm6dsx: add support to i2c pullup resistors
iio: imu: st_lsm6dsx: add hw FIFO support to i2c controller
iio: imu: st_lsm6dsx: add st_lsm6dsx_push_tagged_data routine
iio: imu: st_lsm6dsx: add i2c embedded controller support
iio: imu: st_lsm6dsx: introduce st_lsm6dsx_sensor_set_enable routine
iio: imu: st_lsm6dsx: introduce ST_LSM6DSX_ID_EXT sensor ids
iio: imu: st_lsm6dsx: remove static from st_lsm6dsx_set_watermark
iio: imu: st_lsm6dsx: reload trimming parameter at bootstrap
iio: imu: st_lsm6dsx: introduce locked read/write utility routines
...
Jonathan writes:
First set of IIO fixes for the 4.20 cycle.
* st_magn
- Avoid an ordering issue that lead to large numbers of unhandled
interrupts whilst enabling buffered capture.
* hid-sensors
- Fix a long running problem with signed values reading wrong from
sysfs on these sensors. It appears people were only using the
buffered interface. These typically occur in laptops so chances
are everyone was using the sensor-proxy which will use the buffered
interface by default.
* tag 'iio-fixes-for-4.20a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio:
iio/hid-sensors: Fix IIO_CHAN_INFO_RAW returning wrong values for signed numbers
iio:st_magn: Fix enable device after trigger
In some existing lantiq driver, the C codes include lantiq_soc.h
header file directly.
./arch/mips/include/asm/mach-lantiq/falcon/lantiq_soc.h
./arch/mips/include/asm/mach-lantiq/xway/lantiq_soc.h
Those drivers need to be extended to support more platform.
lantiq.h is added in include/linux/ to make it
globally available and provides some wrapper codes.
Signed-off-by: Songjun Wu <songjun.wu@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit aaf9978c3c.
Quoting Peter:
There is a HID feature report called "Resolution Multiplier"
Described in the "Enhanced Wheel Support in Windows" doc and
the "USB HID Usage Tables" page 30.
http://download.microsoft.com/download/b/d/1/bd1f7ef4-7d72-419e-bc5c-9f79ad7bb66e/wheel.docxhttps://www.usb.org/sites/default/files/documents/hut1_12v2.pdf
This was new for Windows Vista, so we're only a decade behind here. I only
accidentally found this a few days ago while debugging a stuck button on a
Microsoft mouse.
The docs above describe it like this: a wheel control by default sends
value 1 per notch. If the resolution multiplier is active, the wheel is
expected to send a value of $multiplier per notch (e.g. MS Sculpt mouse) or
just send events more often, i.e. for less physical motion (e.g. MS Comfort
mouse).
For the latter, you need the right HW of course. The Sculpt mouse has
tactile wheel clicks, so nothing really changes. The Comfort mouse has
continuous motion with no tactile clicks. Similar to the free-wheeling
Logitech mice but without any inertia.
Note that the doc also says that Vista and onwards *always* enable this
feature where available.
An example HID definition looks like this:
Usage Page Generic Desktop (0x01)
Usage Resolution Multiplier (0x48)
Logical Minimum 0
Logical Maximum 1
Physical Minimum 1
Physical Maximum 16
Report Size 2 # in bits
Report Count 1
Feature (Data, Var, Abs)
So the actual bits have values 0 or 1 and that reflects real values 1 or 16.
We've only seen single-bits so far, so there's low-res and hi-res, but
nothing in between.
The multiplier is available for HID usages "Wheel" and "AC Pan" (horiz wheel).
Microsoft suggests that
> Vendors should ship their devices with smooth scrolling disabled and allow
> Windows to enable it. This ensures that the device works like a regular HID
> device on legacy operating systems that do not support smooth scrolling.
(see the wheel doc linked above)
The mice that we tested so far do reset on unplug.
Device Support looks to be all (?) Microsoft mice but nothing else
Not supported:
- Logitech G500s, G303
- Roccat Kone XTD
- all the cheap Lenovo, HP, Dell, Logitech USB mice that come with a
workstation that I could find don't have it.
- Etekcity something something
- Razer Imperator
Supported:
- Microsoft Comfort Optical Mouse 3000 - yes, physical: 1:4
- Microsoft Sculpt Ergonomic Mouse - yes, physical: 1:12
- Microsoft Surface mouse - yes, physical: 1:4
So again, I think this is really just available on Microsoft mice, but
probably all decent MS mice released over the last decade.
Looking at the hardware itself:
- no noticeable notches in the weel
- low-res: 18 events per 360deg rotation (click angle 20 deg)
- high-res: 72 events per 360deg → matches multiplier of 4
- I can feel the notches during wheel turns
- low-res: 24 events per 360 deg rotation (click angle 15 deg)
- horiz wheel is tilt-based, continuous output value 1
- high-res: 24 events per 360deg with value 12 → matches multiplier of 12
- horiz wheel output rate doubles/triples?, values is 3
- It's a touch strip, not a wheel so no notches
- high-res: events have value 4 instead of 1
a bit strange given that it doesn't actually have notches.
Ok, why is this an issue for the current API? First, because the logitech
multiplier used in Harry's patches looks suspiciously like the Resolution
Multiplier so I think we should assume it's the same thing. Nestor, can you
shed some light on that?
- `REL_WHEEL` is defined as the number of notches, emulated where needed.
- `REL_WHEEL_HI_RES` is the movement of the user's finger in microns.
- `WM_MOUSEWHEEL` (Windows) is is a multiple of 120, defined as "the threshold
for action to be taken and one such action"
https://docs.microsoft.com/en-us/windows/desktop/inputdev/wm-mousewheel
If the multiplier is set to M, this means we need an accumulated value of M
until we can claim there was a wheel click. So after enabling the multiplier
and setting it to the maximum (like Windows):
- M units are 15deg rotation → 1 unit is 2620/M micron (see below). This is
the `REL_WHEEL_HI_RES` value.
- wheel diameter 20mm: 15 deg rotation is 2.62mm, 2620 micron (pi * 20mm /
(360deg/15deg))
- For every M units accumulated, send one `REL_WHEEL` event
The problem here is that we've now hardcoded 20mm/15 deg into the kernel and
we have no way of getting the size of the wheel or the click angle into the
kernel.
In userspace we now have to undo the kernel's calculation. If our click angle
is e.g. 20 degree we have to undo the (lossy) calculation from the kernel and
calculate the correct angle instead. This also means the 15 is a hardcoded
option forever and cannot be changed.
In hid-logitech-hidpp.c, the microns per unit is hardcoded per device.
Harry, did you measure those by hand? We'd need to update the kernel for
every device and there are 10 years worth of devices from MS alone.
The multiplier default is 8 which is in the right ballpark, so I'm pretty
sure this is the same as the Resolution Multiplier, just in HID++ lingo. And
given that the 120 magic factor is what Windows uses in the end, I can't
imagine Logitech rolling their own thing here. Nestor?
And we're already fairly inaccurate with the microns anyway. The MX Anywhere
2S has a click angle of 20 degrees (18 stops) and a 17mm wheel, so a wheel
notch is approximately 2.67mm, one event at multiplier 8 (1/8 of a notch)
would be 334 micron. That's only 80% of the fallback value of 406 in the
kernel. Multiplier 6 gives us 445micron (10% off). I'm assuming multiplier 7
doesn't exist because it's not a factor of 120.
Summary:
Best option may be to simply do what Windows is doing, all the HW manufacturers
have to use that approach after all. Switch `REL_WHEEL_HI_RES` to report in
fractions of 120, with 120 being one notch and divide that by the multiplier
for the actual events. So e.g. the Logitech multiplier 8 would send value 15
for each event in hi-res mode. This can be converted in userspace to
whatever userspace needs (combined with a hwdb there that tells you wheel
size/click angle/...).
Conflicts:
include/uapi/linux/input-event-codes.h -> I kept the new
reserved event in the code, so I had to adapt the revert
slightly
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Harry Cutts <hcutts@chromium.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Jiri Kosina <jkosina@suse.cz>
The new emulate_pr backstore attribute allows for Persistent Reservation
and SCSI2 RESERVE/RELEASE support to be completely disabled. This can be
useful for scenarios such as:
- Ensuring ATS (Compare & Write) usage on recent VMware ESXi initiators.
- Allowing clustered (e.g. tcm-user) backends to block such requests,
avoiding the multi-node reservation state propagation.
When explicitly disabled, PR and RESERVE/RELEASE requests receive Invalid
Command Operation Code response sense data.
Signed-off-by: David Disseldorp <ddiss@suse.de>
Reviewed-by: Mike Christie <mchristi@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
drm-misc-next for v4.21, part 2:
UAPI Changes:
- Remove syncobj timeline support from drm.
Cross-subsystem Changes:
- Document canvas provider node in the DT bindings.
- Improve documentation for TPO TPG110 DT bindings.
Core Changes:
- Use explicit state in drm atomic functions.
- Add panel quirk for new GPD Win2 firmware.
- Add DRM_FORMAT_XYUV8888.
- Set the default import/export function in prime to drm_gem_prime_import/export.
- Add a separate drm_gem_object_funcs, to stop relying on dev->driver->*gem* functions.
- Make sure that tinydrm sets the virtual address also on imported buffers.
Driver Changes:
- Support active-low data enable signal in sun4i.
- Fix scaling in vc4.
- Use canvas provider node in meson.
- Remove unused variables in sti and qxl and cirrus.
- Add overlay plane support and primary plane scaling to meson.
- i2c fixes in drm/bridge/sii902x
- Fix mailbox read size in rockchip.
- Spelling fix in panel/s6d16d0.
- Remove unnecessary null check from qxl_bo_unref.
- Remove unused arguments from qxl_bo_pin.
- Fix qxl cursor pinning.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/9c0409e3-a85f-d2af-b4eb-baf1eb8bbae4@linux.intel.com
Allow querying bridge port flags so that drivers capable of performing
VxLAN learning will update the bridge driver only if learning is enabled
on its bridge port corresponding to the VxLAN device.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to allow devices to signal learning events to VXLAN, introduce
two new switchdev messages: SWITCHDEV_VXLAN_FDB_ADD_TO_BRIDGE and
SWITCHDEV_VXLAN_FDB_DEL_TO_BRIDGE.
Listen to these notifications in the vxlan driver. The FDB entries
learned this way have an NTF_EXT_LEARNED flag, and only entries marked
as such can be unlearned by the _DEL_ event. They are also immediately
marked as offloaded. This is the same behavior that the bridge driver
observes.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The VXLAN driver needs to differentiate between FDB entries learned by
the VXLAN driver, and those added by the user. The latter ones shouldn't
be taken over by external learning events. This is in accordance with
bridge behavior.
Therefore, extend the flags bitfield to 16 bits and add a new private
NTF flag to mark the user-added entries.
This seems preferable to adding a dedicated boolean, because passing the
flag, unlike passing e.g. a true, makes it clear what the meaning of the
bit is.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jean-Louis reported a TCP regression and bisected to recent SACK
compression.
After a loss episode (receiver not able to keep up and dropping
packets because its backlog is full), linux TCP stack is sending
a single SACK (DUPACK).
Sender waits a full RTO timer before recovering losses.
While RFC 6675 says in section 5, "Algorithm Details",
(2) If DupAcks < DupThresh but IsLost (HighACK + 1) returns true --
indicating at least three segments have arrived above the current
cumulative acknowledgment point, which is taken to indicate loss
-- go to step (4).
...
(4) Invoke fast retransmit and enter loss recovery as follows:
there are old TCP stacks not implementing this strategy, and
still counting the dupacks before starting fast retransmit.
While these stacks probably perform poorly when receivers implement
LRO/GRO, we should be a little more gentle to them.
This patch makes sure we do not enable SACK compression unless
3 dupacks have been sent since last rcv_nxt update.
Ideally we should even rearm the timer to send one or two
more DUPACK if no more packets are coming, but that will
be work aiming for linux-4.21.
Many thanks to Jean-Louis for bisecting the issue, providing
packet captures and testing this patch.
Fixes: 5d9f4262b7 ("tcp: add SACK compression")
Reported-by: Jean-Louis Dupond <jean-louis@dupond.be>
Tested-by: Jean-Louis Dupond <jean-louis@dupond.be>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Abstract CFI/DEI bit access consistently with other VLAN tag fields.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Structures of ib_verbs.h don't use fields/structures of mm.h, socket.h or
scatterlist.h. So remove such header files inclusion.
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
From git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux
mlx5 updates taken for dependencies on later ODP patches.
Conflict resolved by deleting mlx5_ib_get_vector_affinity()
* branch 'mlx5-next': (21 commits)
net/mlx5: EQ, Make EQE access methods inline
{net,IB}/mlx5: Move Page fault EQ and ODP logic to RDMA
net/mlx5: EQ, Generic EQ
net/mlx5: EQ, Different EQ types
net/mlx5: EQ, Privatize eq_table and friends
net/mlx5: EQ, irq_info and rmap belong to eq_table
net/mlx5: EQ, Create all EQs in one place
net/mlx5: EQ, Move all EQ logic to eq.c
net/mlx5: EQ, Remove redundant completion EQ list lock
net/mlx5: EQ, No need to store eq index as a field
net/mlx5: EQ, Remove unused fields and structures
net/mlx5: EQ, Use the right place to store/read IRQ affinity hint
IB/mlx5: Improve ODP debugging messages
net/mlx5: Use multi threaded workqueue for page fault handling
net/mlx5: Return success for PAGE_FAULT_RESUME in internal error state
IB/mlx5: Lock QP during page fault handling
net/mlx5: Enumerate page fault types
net/mlx5: Add interface to hold and release core resources
net/mlx5: Release resource on error flow
net/mlx5: Fix offsets of ifc reserved fields
...
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
With the overflow buffer removed, we no longer have a unique address
which is guaranteed not to be a valid DMA target to use as an error
token. The DIRECT_MAPPING_ERROR value of 0 tries to at least represent
an unlikely DMA target, but unfortunately there are already SWIOTLB
users with DMA-able memory at physical address 0 which now gets falsely
treated as a mapping failure and leads to all manner of misbehaviour.
The best we can do to mitigate that is flip DIRECT_MAPPING_ERROR to the
other commonly-used error value of all-bits-set, since the last single
byte of memory is by far the least-likely-valid DMA target.
Fixes: dff8d6c1ed ("swiotlb: remove the overflow buffer")
Reported-by: John Stultz <john.stultz@linaro.org>
Tested-by: John Stultz <john.stultz@linaro.org>
Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
If the CPU assigned to the xgene PMU is taken offline, then subsequent
perf invocations on the PMU will fail:
# echo 0 > /sys/devices/system/cpu/cpu0/online
# perf stat -a -e l3c0/cycle-count/,l3c0/write/ sleep 1
Error:
The sys_perf_event_open() syscall returned with 19 (No such device) for event (l3c0/cycle-count/).
/bin/dmesg may provide additional information.
No CONFIG_PERF_EVENTS=y kernel support configured?
This patch implements a hotplug notifier in the xgene PMU driver so that
the PMU context is migrated to another online CPU should its assigned
CPU disappear.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Hoan Tran <hoan.tran@amperecomputing.com>
[will: Made naming of new cpuhp_state enum entry consistent]
Signed-off-by: Will Deacon <will.deacon@arm.com>
Adopt the SPDX license identifier headers to ease license compliance
management.
Cc: Eric Anholt <eric@anholt.net>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
asoc_simple_card_of_parse_routing() had "option" parameter
to consider error handling, but it is very pointless parameter.
Let's remove it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current simple-card-utils has asoc_simple_card_parse_convert() to parse
convert channel/rate for be_hw_params_fixup.
But, it is parsing from top of node.
If sound card had multi subnode, we need to parse it from each sub node.
This patch tidyup asoc_simple_card_parse_convert() to allow parsing
settings from each node.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Armv8.1 allocated the upper 32-bits of the PMCEID registers to describe
the common architectural and microarchitecture events beginning at 0x4000.
Add support for these registers to our probing code, so that we can
advertise the SPE events when they are supported by the CPU.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Even though .mq_kobj, ctx->kobj and q->kobj share same lifetime
from block layer's view, actually they don't because userspace may
grab one kobject anytime via sysfs.
This patch fixes the issue by the following approach:
1) introduce 'struct blk_mq_ctxs' for holding .mq_kobj and managing
all ctxs
2) free all allocated ctxs and the 'blk_mq_ctxs' instance in release
handler of .mq_kobj
3) grab one ref of .mq_kobj before initializing each ctx->kobj, so that
.mq_kobj is always released after all ctxs are freed.
This patch fixes kernel panic issue during booting when DEBUG_KOBJECT_RELEASE
is enabled.
Reported-by: Guenter Roeck <linux@roeck-us.net>
Cc: "jianchao.wang" <jianchao.w.wang@oracle.com>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The current methods for obtaining FP context via ptrace only provide
either 32 or 64 bits per data register. With MSA, where vector registers
are aliased with scalar FP data registers, those registers are 128 bits
wide. Thus a new mechanism is required for userland to access those
registers via ptrace. This patch introduces an NT_MIPS_MSA regset which
provides, in this order:
- The full 128 bits value of each vector register, in native
endianness saved as though elements are doubles. That is, the format
of each vector register is as would be obtained by saving it to
memory using an st.d instruction.
- The 32 bit scalar FP implementation register (FIR).
- The 32 bit scalar FP control & status register (FCSR).
- The 32 bit MSA implementation register (MSAIR).
- The 32 bit MSA control & status register (MSACSR).
The provision of the FIR & FCSR registers in addition to the MSA
equivalents allows scalar FP context to be retrieved as a subset of
the context available via this regset. Along with the MSA equivalents
they also nicely form the final 128 bit "register" of the regset.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/21180/
Cc: linux-mips@linux-mips.org
Kernel test robot (lkp@intel.com) reports a compilation error at
https://www.spinics.net/lists/netdev/msg534913.html
introduced by commit 838e96904f ("bpf: Introduce bpf_func_info").
If CONFIG_BPF is defined and CONFIG_BPF_SYSCALL is not defined,
the following error will appear:
kernel/bpf/core.c:414: undefined reference to `btf_type_by_id'
kernel/bpf/core.c:415: undefined reference to `btf_name_by_offset'
When CONFIG_BPF_SYSCALL is not defined,
let us define stub inline functions for btf_type_by_id()
and btf_name_by_offset() in include/linux/btf.h.
This way, the compilation failure can be avoided.
Fixes: 838e96904f ("bpf: Introduce bpf_func_info")
Reported-by: kbuild test robot <lkp@intel.com>
Cc: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
This patch added interface to load a program with the following
additional information:
. prog_btf_fd
. func_info, func_info_rec_size and func_info_cnt
where func_info will provide function range and type_id
corresponding to each function.
The func_info_rec_size is introduced in the UAPI to specify
struct bpf_func_info size passed from user space. This
intends to make bpf_func_info structure growable in the future.
If the kernel gets a different bpf_func_info size from userspace,
it will try to handle user request with part of bpf_func_info
it can understand. In this patch, kernel can understand
struct bpf_func_info {
__u32 insn_offset;
__u32 type_id;
};
If user passed a bpf func_info record size of 16 bytes, the
kernel can still handle part of records with the above definition.
If verifier agrees with function range provided by the user,
the bpf_prog ksym for each function will use the func name
provided in the type_id, which is supposed to provide better
encoding as it is not limited by 16 bytes program name
limitation and this is better for bpf program which contains
multiple subprograms.
The bpf_prog_info interface is also extended to
return btf_id, func_info, func_info_rec_size and func_info_cnt
to userspace, so userspace can print out the function prototype
for each xlated function. The insn_offset in the returned
func_info corresponds to the insn offset for xlated functions.
With other jit related fields in bpf_prog_info, userspace can also
print out function prototypes for each jited function.
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
This patch adds BTF_KIND_FUNC and BTF_KIND_FUNC_PROTO
to support the function debug info.
BTF_KIND_FUNC_PROTO must not have a name (i.e. !t->name_off)
and it is followed by >= 0 'struct bpf_param' objects to
describe the function arguments.
The BTF_KIND_FUNC must have a valid name and it must
refer back to a BTF_KIND_FUNC_PROTO.
The above is the conclusion after the discussion between
Edward Cree, Alexei, Daniel, Yonghong and Martin.
By combining BTF_KIND_FUNC and BTF_LIND_FUNC_PROTO,
a complete function signature can be obtained. It will be
used in the later patches to learn the function signature of
a running bpf program.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Some old Samsung drivers use the legacy crop API incorrectly:
the crop and compose targets are swapped. Normally VIDIOC_G_CROP
will return the CROP rectangle of a CAPTURE stream and the COMPOSE
rectangle of an OUTPUT stream.
The Samsung drivers do the opposite. Note that these drivers predate
the selection API.
If this 'QUIRK' flag is set, then the v4l2-ioctl core will swap
the CROP and COMPOSE targets as well.
That way backwards compatibility is ensured and we can convert the
Samsung drivers to the selection API.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Tested-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add mlx5_eq_{create/destroy}_generic APIs and EQE access methods, for
mlx5 core consumers generic EQs.
This API will be used in downstream patch to move page fault (RDMA ODP)
EQ logic into mlx5_ib rdma driver, hence it will use a generic EQ.
Current mlx5 EQ allocation scheme:
On load mlx5 allocates 4 (for async) + #cores (for data completions)
MSIX vectors, mlx5 core will assign 3 MSIX vectors for internal async
EQs and will use all of the #cores MSIX vectors for completion EQs,
(One vector is going to be reserved for a generic EQ).
After this patch an external user (e.g mlx5_ib) of mlx5_core
can use this new API to create new generic EQs with the reserved msix
vector index for that eq.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
In mlx5 we have three types of usages for EQs,
1. Asynchronous EQs, used internally by mlx5 core for
a. FW command completions
b. FW page requests
c. one EQ for all other Asynchronous events
2. Completion EQs, used for CQ completion (we create one per core)
3. *Special type of EQ (page fault) used for RDMA on demand paging
(ODP).
*The 3rd type shouldn't be special at least in mlx5 core, it is yet
another async events EQ with specific use case, it will be removed in
the next two patches, and will completely move its logic to mlx5_ib,
as it is rdma specific.
In this patch we remove use case (eq type) specific fields from
struct mlx5_eq into a new eq type specific structures.
struct mlx5_eq_async;
truct mlx5_eq_comp;
struct mlx5_eq_pagefault;
Separate between their type specific flows.
In the future we will allow users to create there own generic EQs.
for now we will allow only one for ODP in next patches.
We will introduce event listeners registration API for those who
want to receive mlx5 async events.
After that mlx5 eq handling will be clean from feature/user specific
handling.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Move unnecessary EQ table structures and declaration from the
public include/linux/mlx5/driver.h into the private area of mlx5_core
and into eq.c/eq.h.
Introduce new mlx5 EQ APIs:
mlx5_comp_vectors_count(dev);
mlx5_comp_irq_get_affinity_mask(dev, vector);
And use them from mlx5_ib or mlx5e netdevice instead of direct access to
mlx5_core internal structures.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
irq_info and rmap are EQ properties of the driver, and only needed for
EQ objects, move them to the eq_table EQs database structure.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
eq->index is used only for completion EQs and is assigned to be
the completion eq index, it is used only when traversing the completion
eqs list, and it can be calculated dynamically, thus remove the
eq->index field.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Currently the cpu affinity hint mask for completion EQs is stored and
read from the wrong place, since reading and storing is done from the
same index, there is no actual issue with that, but internal irq_info
for completion EQs stars at MLX5_EQ_VEC_COMP_BASE offset in irq_info
array, this patch changes the code to use the correct offset to store
and read the IRQ affinity hint.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
The changes for HDaudio overlooked the fact that the machine drivers
used for Chromebooks rely on the dmic number information passed as
pdata.
Add dmic_num field to standard interface and use standard interface
instead of SKL-specific one.
Also clean-up pdata definition to remove fields that are no longer
used.
Fixes: 842bb5135f ('ASoC: Intel: use standard interface for Hdaudio machine driver')
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Most modern SPI controllers can directly map a SPI memory (or a portion
of the SPI memory) in the CPU address space. Most of the time this
brings significant performance improvements as it automates the whole
process of sending SPI memory operations every time a new region is
accessed.
This new API allows SPI memory drivers to create direct mappings and
then use them to access the memory instead of using spi_mem_exec_op().
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When defining spi_mem_op templates we don't necessarily know the size
that will be passed when the template is actually used, and basing the
supports_op() check on op->data.nbytes to know whether there will be
data transferred for a specific operation is this not possible.
Add SPI_MEM_NO_DATA to the spi_mem_data_dir enum so that we can base
our checks on op->data.dir instead of op->data.nbytes.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
