This converts the Wolfson Micro WM831x DCDC converter to use
a GPIO descriptor for the GPIO driving the DVS pin.
There is just one (non-DT) machine in the kernel using this, and
that is the Wolfson Micro (now Cirrus) Cragganmore 6410 so we
patch this board to pass a descriptor table and fix up the driver
accordingly.
Cc: Charles Keepax <ckeepax@opensource.cirrus.com>
Cc: Richard Fitzgerald <rf@opensource.cirrus.com>
Cc: patches@opensource.cirrus.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The FMC subsystem was created in 2012 with the ambition to
drive development of drivers for this hardware upstream.
The current implementation has architectural flaws and would
need to be revamped using real hardware to something that can
reuse existing kernel abstractions in the subsystems for e.g.
I2C, FPGA and GPIO.
We have concluded that for the mainline kernel it will be
better to delete the subsystem and start over with a clean
slate when/if an active maintainer steps up.
For details see:
https://lkml.org/lkml/2018/10/29/534
Suggested-by: Federico Vaga <federico.vaga@cern.ch>
Cc: Pat Riehecky <riehecky@fnal.gov>
Acked-by: Alessandro Rubini <rubini@gnudd.com>
Signed-off-by: Federico Vaga <federico.vaga@cern.ch>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Future SoCs are going to have more than 255 device clocks in certain cases,
and thus the API must be extended to support this. The support is done in
backwards compatible extension, in which the new u32 clock identifier
fields are only used if the existing u8 size clock identifier is set as
255. In all the other cases, the existing u8 clock identifier is used. As
the size of the messages sent / received is not verified for existing
devices / old firmware, increasing the size of the messages from the end
is also fine. Due to this reason, depending on ABI version isn't necessary
either.
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
In preparation for dealing with scales within the SCMI HWMON driver,
fetch and store the sensor unit scale into the scmi_sensor_info
structure. In order to simplify computations for upper layer, take care
of sign extending the scale to a full 8-bit signed value.
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
[sudeep.holla: update bitfield values as per specification]
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
We've moved the override and firmware EDID (simply "override EDID" from
now on) handling to the low level drm_do_get_edid() function in order to
transparently use the override throughout the stack. The idea is that
you get the override EDID via the ->get_modes() hook.
Unfortunately, there are scenarios where the DDC probe in drm_get_edid()
called via ->get_modes() fails, although the preceding ->detect()
succeeds.
In the case reported by Paul Wise, the ->detect() hook,
intel_crt_detect(), relies on hotplug detect, bypassing the DDC. In the
case reported by Ilpo Järvinen, there is no ->detect() hook, which is
interpreted as connected. The subsequent DDC probe reached via
->get_modes() fails, and we don't even look at the override EDID,
resulting in no modes being added.
Because drm_get_edid() is used via ->detect() all over the place, we
can't trivially remove the DDC probe, as it leads to override EDID
effectively meaning connector forcing. The goal is that connector
forcing and override EDID remain orthogonal.
Generally, the underlying problem here is the conflation of ->detect()
and ->get_modes() via drm_get_edid(). The former should just detect, and
the latter should just get the modes, typically via reading the EDID. As
long as drm_get_edid() is used in ->detect(), it needs to retain the DDC
probe. Or such users need to have a separate DDC probe step first.
The EDID caching between ->detect() and ->get_modes() done by some
drivers is a further complication that prevents us from making
drm_do_get_edid() adapt to the two cases.
Work around the regression by falling back to a separate attempt at
getting the override EDID at drm_helper_probe_single_connector_modes()
level. With a working DDC and override EDID, it'll never be called; the
override EDID will come via ->get_modes(). There will still be a failing
DDC probe attempt in the cases that require the fallback.
v2:
- Call drm_connector_update_edid_property (Paul)
- Update commit message about EDID caching (Daniel)
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=107583
Reported-by: Paul Wise <pabs3@bonedaddy.net>
Cc: Paul Wise <pabs3@bonedaddy.net>
References: http://mid.mail-archive.com/alpine.DEB.2.20.1905262211270.24390@whs-18.cs.helsinki.fi
Reported-by: Ilpo Järvinen <ilpo.jarvinen@cs.helsinki.fi>
Cc: Ilpo Järvinen <ilpo.jarvinen@cs.helsinki.fi>
Suggested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
References: 15f080f08d ("drm/edid: respect connector force for drm_get_edid ddc probe")
Fixes: 53fd40a90f ("drm: handle override and firmware EDID at drm_do_get_edid() level")
Cc: <stable@vger.kernel.org> # v4.15+ 56a2b7f2a3 drm/edid: abstract override/firmware EDID retrieval
Cc: <stable@vger.kernel.org> # v4.15+
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Harish Chegondi <harish.chegondi@intel.com>
Tested-by: Paul Wise <pabs3@bonedaddy.net>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190610093054.28445-1-jani.nikula@intel.com
Introduce a new type for reserved region. This corresponds
to directly mapped regions which are known to be relaxable
in some specific conditions, such as device assignment use
case. Well known examples are those used by USB controllers
providing PS/2 keyboard emulation for pre-boot BIOS and
early BOOT or RMRRs associated to IGD working in legacy mode.
Since commit c875d2c1b8 ("iommu/vt-d: Exclude devices using RMRRs
from IOMMU API domains") and commit 18436afdc1 ("iommu/vt-d: Allow
RMRR on graphics devices too"), those regions are currently
considered "safe" with respect to device assignment use case
which requires a non direct mapping at IOMMU physical level
(RAM GPA -> HPA mapping).
Those RMRRs currently exist and sometimes the device is
attempting to access it but this has not been considered
an issue until now.
However at the moment, iommu_get_group_resv_regions() is
not able to make any difference between directly mapped
regions: those which must be absolutely enforced and those
like above ones which are known as relaxable.
This is a blocker for reporting severe conflicts between
non relaxable RMRRs (like MSI doorbells) and guest GPA space.
With this new reserved region type we will be able to use
iommu_get_group_resv_regions() to enumerate the IOVA space
that is usable through the IOMMU API without introducing
regressions with respect to existing device assignment
use cases (USB and IGD).
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Some IOMMU hardware features, for example PCI PRI and Arm SMMU Stall,
enable recoverable I/O page faults. Allow IOMMU drivers to report PRI Page
Requests and Stall events through the new fault reporting API. The
consumer of the fault can be either an I/O page fault handler in the host,
or a guest OS.
Once handled, the fault must be completed by sending a page response back
to the IOMMU. Add an iommu_page_response() function to complete a page
fault.
There are two ways to extend the userspace API:
* Add a field to iommu_page_response and a flag to
iommu_page_response::flags describing the validity of this field.
* Introduce a new iommu_page_response_X structure with a different version
number. The kernel must then support both versions.
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Jean-Philippe Brucker <jean-philippe.brucker@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Traditionally, device specific faults are detected and handled within
their own device drivers. When IOMMU is enabled, faults such as DMA
related transactions are detected by IOMMU. There is no generic
reporting mechanism to report faults back to the in-kernel device
driver or the guest OS in case of assigned devices.
This patch introduces a registration API for device specific fault
handlers. This differs from the existing iommu_set_fault_handler/
report_iommu_fault infrastructures in several ways:
- it allows to report more sophisticated fault events (both
unrecoverable faults and page request faults) due to the nature
of the iommu_fault struct
- it is device specific and not domain specific.
The current iommu_report_device_fault() implementation only handles
the "shoot and forget" unrecoverable fault case. Handling of page
request faults or stalled faults will come later.
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Jean-Philippe Brucker <jean-philippe.brucker@arm.com>
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Device faults detected by IOMMU can be reported outside the IOMMU
subsystem for further processing. This patch introduces
a generic device fault data structure.
The fault can be either an unrecoverable fault or a page request,
also referred to as a recoverable fault.
We only care about non internal faults that are likely to be reported
to an external subsystem.
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Jean-Philippe Brucker <jean-philippe.brucker@arm.com>
Signed-off-by: Liu, Yi L <yi.l.liu@linux.intel.com>
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
DMA faults can be detected by IOMMU at device level. Adding a pointer
to struct device allows IOMMU subsystem to report relevant faults
back to the device driver for further handling.
For direct assigned device (or user space drivers), guest OS holds
responsibility to handle and respond per device IOMMU fault.
Therefore we need fault reporting mechanism to propagate faults beyond
IOMMU subsystem.
There are two other IOMMU data pointers under struct device today, here
we introduce iommu_param as a parent pointer such that all device IOMMU
data can be consolidated here. The idea was suggested here by Greg KH
and Joerg. The name iommu_param is chosen here since iommu_data has been
used.
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Link: https://lkml.org/lkml/2017/10/6/81
Signed-off-by: Joerg Roedel <jroedel@suse.de>
This function was used by pin_request() to pointlessly double-check
the pin validity, and it was the only user ever.
Since commit d2f6a1c6fb ("pinctrl: remove double pin validity
check."), no one has ever used it.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add binding for the QMP based side-channel communication mechanism to
the AOSS, which is used to control resources not exposed through the
RPMh interface.
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Like all other destroy commands, .destroy_cq() call is not supposed
to fail. In all flows, the attempt to return earlier caused to memory
leaks.
This patch converts .destroy_cq() to do not return any errors.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Acked-by: Gal Pressman <galpress@amazon.com>
Acked-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
TLS offload drivers keep track of TCP seq numbers to make sure
the packets are fed into the HW in order.
When packets get dropped on the way through the stack, the driver
will get out of sync and have to use fallback encryption, but unless
TCP seq number is resynced it will never match the packets correctly
(or even worse - use incorrect record sequence number after TCP seq
wraps).
Existing drivers (mlx5) feed the entire record on every out-of-order
event, allowing FW/HW to always be in sync.
This patch adds an alternative, more akin to the RX resync. When
driver sees a frame which is past its expected sequence number the
stream must have gotten out of order (if the sequence number is
smaller than expected its likely a retransmission which doesn't
require resync). Driver will ask the stack to perform TX sync
before it submits the next full record, and fall back to software
crypto until stack has performed the sync.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently only RX direction is ever resynced, however, TX may
also get out of sequence if packets get dropped on the way to
the driver. Rename the resync callback and add a direction
parameter.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TLS offload device may lose sync with the TCP stream if packets
arrive out of order. Drivers can currently request a resync at
a specific TCP sequence number. When a record is found starting
at that sequence number kernel will inform the device of the
corresponding record number.
This requires the device to constantly scan the stream for a
known pattern (constant bytes of the header) after sync is lost.
This patch adds an alternative approach which is entirely under
the control of the kernel. Kernel tracks records it had to fully
decrypt, even though TLS socket is in TLS_HW mode. If multiple
records did not have any decrypted parts - it's a pretty strong
indication that the device is out of sync.
We choose the min number of fully encrypted records to be 2,
which should hopefully be more than will get retransmitted at
a time.
After kernel decides the device is out of sync it schedules a
resync request. If the TCP socket is empty the resync gets
performed immediately. If socket is not empty we leave the
record parser to resync when next record comes.
Before resync in message parser we peek at the TCP socket and
don't attempt the sync if the socket already has some of the
next record queued.
On resync failure (encrypted data continues to flow in) we
retry with exponential backoff, up to once every 128 records
(with a 16k record thats at most once every 2M of data).
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
handle_device_resync() doesn't describe the function very well.
The function checks if resync should be issued upon parsing of
a new record.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TLS offload code casts record number to a u64. The buffer
should be aligned to 8 bytes, but its actually a __be64, and
the rest of the TLS code treats it as big int. Make the
offload callbacks take a byte array, drivers can make the
choice to do the ugly cast if they want to.
Prepare for copying the record number onto the stack by
defining a constant for max size of the byte array.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On Rockchip rk3288-based Chromebooks when you do a suspend/resume
cycle:
1. You lose the ability to detect an HDMI device being plugged in.
2. If you're using the i2c bus built in to dw_hdmi then it stops
working.
Let's add a hook to the core dw-hdmi driver so that we can call it in
dw_hdmi-rockchip in the next commit.
NOTE: the exact set of steps I've done here in resume come from
looking at the normal dw_hdmi init sequence in upstream Linux plus the
sequence that we did in downstream Chrome OS 3.14. Testing show that
it seems to work, but if an extra step is needed or something here is
not needed we could improve it.
As part of this change we'll refactor the hardware init bits of
dw-hdmi to happen all in one function and all at the same time. Since
we need to init the interrupt mutes before we request the IRQ, this
means moving the hardware init earlier in the function, but there
should be no problems with that. Also as part of this we now
unconditionally init the "i2c" parts of dw-hdmi, but again that ought
to be fine.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190604204207.168085-1-dianders@chromium.org
There are some conflicts due to SPDX changes. We also have more
patches being merged via media tree touching them.
So, let's merge back from upstream and address those.
Linux 5.2-rc4
* tag 'v5.2-rc4': (767 commits)
Linux 5.2-rc4
MAINTAINERS: Karthikeyan Ramasubramanian is MIA
i2c: xiic: Add max_read_len quirk
lockref: Limit number of cmpxchg loop retries
uaccess: add noop untagged_addr definition
x86/insn-eval: Fix use-after-free access to LDT entry
kbuild: use more portable 'command -v' for cc-cross-prefix
s390/unwind: correct stack switching during unwind
block, bfq: add weight symlink to the bfq.weight cgroup parameter
cgroup: let a symlink too be created with a cftype file
drm/nouveau/secboot/gp10[2467]: support newer FW to fix SEC2 failures on some boards
drm/nouveau/secboot: enable loading of versioned LS PMU/SEC2 ACR msgqueue FW
drm/nouveau/secboot: split out FW version-specific LS function pointers
drm/nouveau/secboot: pass max supported FW version to LS load funcs
drm/nouveau/core: support versioned firmware loading
drm/nouveau/core: pass subdev into nvkm_firmware_get, rather than device
block: free sched's request pool in blk_cleanup_queue
pktgen: do not sleep with the thread lock held.
net: mvpp2: Use strscpy to handle stat strings
net: rds: fix memory leak in rds_ib_flush_mr_pool
...
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
All drivers add all their connectors so there's no need to keep around an
array of available connectors. Instead we just put the useable (not
writeback) connectors in a temporary array using
drm_client_for_each_connector_iter() everytime we probe the outputs.
Other places where it's necessary to look at the connectors, we just
iterate over them using the same iterator function.
Rename functions which signature is changed since they will be moved to
drm_client in a later patch.
v6: Improve commit message (Sam Ravnborg)
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190608152657.36613-2-noralf@tronnes.org
Add support for Amazon Graviton custom variant of GICv2m, where the message
is encoded using the MSI message address, as opposed to standard
GICv2m, where the SPI number is encoded in the MSI message data.
In addition, the Graviton flavor of GICv2m is used along GICv3 (and not
GICv2).
Co-developed-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Zeev Zilberman <zeev@amazon.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The audio controllers on Meson8, Meson8b and Meson8m2 use similar
(potentially the same) audio clocks as GXBB, GXL and GXM. Add the
CLKID_CTS_AMCLK, CLKID_CTS_MCLK_I958 and CLKID_CTS_I958 clock IDs so
they can be used for the audio controllers.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Currently, the AF_XDP code uses a separate map in order to
determine if an xsk is bound to a queue. Instead of doing this,
have bpf_map_lookup_elem() return a xdp_sock.
Rearrange some xdp_sock members to eliminate structure holes.
Remove selftest - will be added back in later patch.
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
This more closely follows how other subsytems work, with owner being a
member of the structure containing the function pointers.
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
No reason for every driver to emit code to set this, just make it part of
the driver's existing static const ops structure.
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
No reason for every driver to emit code to set this, just make it part of
the driver's existing static const ops structure.
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
This has been marked CONFIG_BROKEN for over a year now with no complaints.
Delete the whole thing for good.
The module provided the /dev/infiniband/ucmX interface.
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Add support for RTA_NH_ID attribute to allow a user to specify a
nexthop id to use with a route. fc_nh_id is added to fib6_config to
hold the value passed in the RTA_NH_ID attribute. If a nexthop id
is given, the gateway, device, encap and multipath attributes can
not be set.
Update ip6_route_del to check metric and protocol before nexthop
specs. If fc_nh_id is set, then it must match the id in the route
entry. Since IPv6 allows delete of a cached entry (an exception),
add ip6_del_cached_rt_nh to cycle through all of the fib6_nh in
a fib entry if it is using a nexthop.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for RTA_NH_ID attribute to allow a user to specify a
nexthop id to use with a route. fc_nh_id is added to fib_config to
hold the value passed in the RTA_NH_ID attribute. If a nexthop id
is given, the gateway, device, encap and multipath attributes can
not be set.
Update fib_nh_match to check ids on a route delete.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPv6 has traditionally had a single fib6_nh per fib6_info. With
nexthops we can have multiple fib6_nh associated with a fib6_info.
Add a nexthop helper to invoke a callback for each fib6_nh in a
'struct nexthop'. If the callback returns non-0, the loop is
stopped and the return value passed to the caller.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
FMC has its own GPIO handling, the inclusion of <linux/gpio.h>
is only to reuse some flags that we can just as well provide
using local defines.
Cc: Federico Vaga <federico.vaga@cern.ch>
Cc: Pat Riehecky <riehecky@fnal.gov>
Acked-by: Alessandro Rubini <rubini@gnudd.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
So long as a struct hmm pointer exists, so should the struct mm it is
linked too. Hold the mmgrab() as soon as a hmm is created, and mmdrop() it
once the hmm refcount goes to zero.
Since mmdrop() (ie a 0 kref on struct mm) is now impossible with a !NULL
mm->hmm delete the hmm_hmm_destroy().
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Reviewed-by: Jérôme Glisse <jglisse@redhat.com>
Reviewed-by: John Hubbard <jhubbard@nvidia.com>
Reviewed-by: Ralph Campbell <rcampbell@nvidia.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Tested-by: Philip Yang <Philip.Yang@amd.com>
Ralph observes that hmm_range_register() can only be called by a driver
while a mirror is registered. Make this clear in the API by passing in the
mirror structure as a parameter.
This also simplifies understanding the lifetime model for struct hmm, as
the hmm pointer must be valid as part of a registered mirror so all we
need in hmm_register_range() is a simple kref_get.
Suggested-by: Ralph Campbell <rcampbell@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Reviewed-by: John Hubbard <jhubbard@nvidia.com>
Reviewed-by: Ralph Campbell <rcampbell@nvidia.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Tested-by: Philip Yang <Philip.Yang@amd.com>
Some older interconnect target modules need module internal clock
toggling quirks to reset properly. We've been doing this in the
platform code earlier, but need to be able to it directly in the
ti-sysc driver when we no longer rely on on the platform code.
Let's add reset handling for 1-wire, i2c and watchdog. Later on
we can add more modules like msdi and dss as they get tested.
For dra7 pcie, we should be able to just use the rstctrl reset
driver when available.
Signed-off-by: Tony Lindgren <tony@atomide.com>
