fib_trie implementation calls synchronize_rcu when a certain amount of
pages are dirty from freed entries. The number of pages was determined
experimentally in 2009 (commit c3059477fc).
At the current setting, synchronize_rcu is called often -- 51 times in a
second in one test with an average of an 8 msec delay adding a fib entry.
The total impact is a lot of slow down modifying the fib. This is seen
in the output of 'time' - the difference between real time and sys+user.
For example, using 720,022 single path routes and 'ip -batch'[1]:
$ time ./ip -batch ipv4/routes-1-hops
real 0m14.214s
user 0m2.513s
sys 0m6.783s
So roughly 35% of the actual time to install the routes is from the ip
command getting scheduled out, most notably due to synchronize_rcu (this
is observed using 'perf sched timehist').
This patch makes the amount of dirty memory configurable between 64k where
the synchronize_rcu is called often (small, low end systems that are memory
sensitive) to 64M where synchronize_rcu is called rarely during a large
FIB change (for high end systems with lots of memory). The default is 512kB
which corresponds to the current setting of 128 pages with a 4kB page size.
As an example, at 16MB the worst interval shows 4 calls to synchronize_rcu
in a second blocking for up to 30 msec in a single instance, and a total
of almost 100 msec across the 4 calls in the second. The trade off is
allowing FIB entries to consume more memory in a given time window but
but with much better fib insertion rates (~30% increase in prefixes/sec).
With this patch and net.ipv4.fib_sync_mem set to 16MB, the same batch
file runs in:
$ time ./ip -batch ipv4/routes-1-hops
real 0m9.692s
user 0m2.491s
sys 0m6.769s
So the dead time is reduced to about 1/2 second or <5% of the real time.
[1] 'ip' modified to not request ACK messages which improves route
insertion times by about 20%
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
use RCU when accessing the action chain, to avoid use after free in the
traffic path when 'goto chain' is replaced on existing TC actions (see
script below). Since the control action is read in the traffic path
without holding the action spinlock, we need to explicitly ensure that
a->goto_chain is not NULL before dereferencing (i.e it's not sufficient
to rely on the value of TC_ACT_GOTO_CHAIN bits). Not doing so caused NULL
dereferences in tcf_action_goto_chain_exec() when the following script:
# tc chain add dev dd0 chain 42 ingress protocol ip flower \
> ip_proto udp action pass index 4
# tc filter add dev dd0 ingress protocol ip flower \
> ip_proto udp action csum udp goto chain 42 index 66
# tc chain del dev dd0 chain 42 ingress
(start UDP traffic towards dd0)
# tc action replace action csum udp pass index 66
was run repeatedly for several hours.
Suggested-by: Cong Wang <xiyou.wangcong@gmail.com>
Suggested-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
callers of tcf_gact_goto_chain_index() can potentially read an old value
of the chain index, or even dereference a NULL 'goto_chain' pointer,
because 'goto_chain' and 'tcfa_action' are read in the traffic path
without caring of concurrent write in the control path. The most recent
value of chain index can be read also from a->tcfa_action (it's encoded
there together with TC_ACT_GOTO_CHAIN bits), so we don't really need to
dereference 'goto_chain': just read the chain id from the control action.
Fixes: e457d86ada ("net: sched: add couple of goto_chain helpers")
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- pass a pointer to struct tcf_proto in each actions's init() handler,
to allow validating the control action, checking whether the chain
exists and (eventually) refcounting it.
- remove code that validates the control action after a successful call
to the action's init() handler, and replace it with a test that forbids
addition of actions having 'goto_chain' and NULL goto_chain pointer at
the same time.
- add tcf_action_check_ctrlact(), that will validate the control action
and eventually allocate the action 'goto_chain' within the init()
handler.
- add tcf_action_set_ctrlact(), that will assign the control action and
swap the current 'goto_chain' pointer with the new given one.
This disallows 'goto_chain' on actions that don't initialize it properly
in their init() handler, i.e. calling tcf_action_check_ctrlact() after
successful IDR reservation and then calling tcf_action_set_ctrlact()
to assign 'goto_chain' and 'tcf_action' consistently.
By doing this, the kernel does not leak anymore refcounts when a valid
'goto chain' handle is replaced in TC actions, causing kmemleak splats
like the following one:
# tc chain add dev dd0 chain 42 ingress protocol ip flower \
> ip_proto tcp action drop
# tc chain add dev dd0 chain 43 ingress protocol ip flower \
> ip_proto udp action drop
# tc filter add dev dd0 ingress matchall \
> action gact goto chain 42 index 66
# tc filter replace dev dd0 ingress matchall \
> action gact goto chain 43 index 66
# echo scan >/sys/kernel/debug/kmemleak
<...>
unreferenced object 0xffff93c0ee09f000 (size 1024):
comm "tc", pid 2565, jiffies 4295339808 (age 65.426s)
hex dump (first 32 bytes):
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 08 00 06 00 00 00 00 00 00 00 00 00 ................
backtrace:
[<000000009b63f92d>] tc_ctl_chain+0x3d2/0x4c0
[<00000000683a8d72>] rtnetlink_rcv_msg+0x263/0x2d0
[<00000000ddd88f8e>] netlink_rcv_skb+0x4a/0x110
[<000000006126a348>] netlink_unicast+0x1a0/0x250
[<00000000b3340877>] netlink_sendmsg+0x2c1/0x3c0
[<00000000a25a2171>] sock_sendmsg+0x36/0x40
[<00000000f19ee1ec>] ___sys_sendmsg+0x280/0x2f0
[<00000000d0422042>] __sys_sendmsg+0x5e/0xa0
[<000000007a6c61f9>] do_syscall_64+0x5b/0x180
[<00000000ccd07542>] entry_SYSCALL_64_after_hwframe+0x44/0xa9
[<0000000013eaa334>] 0xffffffffffffffff
Fixes: db50514f9a ("net: sched: add termination action to allow goto chain")
Fixes: 97763dc0f4 ("net_sched: reject unknown tcfa_action values")
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit f2780d6d74 "tun: Add ioctl() SIOCGSKNS cmd to allow
obtaining net ns of tun device" it was missed that tun may change
its net ns, while net ns of socket remains the same as it was
created initially. SIOCGSKNS returns net ns of socket, so it is
not suitable for obtaining net ns of device.
We may have two tun devices with the same names in two net ns,
and in this case it's not possible to determ, which of them
fd refers to (TUNGETIFF will return the same name).
This patch adds new ioctl() cmd for obtaining net ns of a device.
Reported-by: Harald Albrecht <harald.albrecht@gmx.net>
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change pcie-xilinx-nwl.c to use pci_msi_mask_irq() and pci_msi_unmask_irq()
like all other PCI host controller drivers. Remove the now-unused
mask_msi_irq() and unmask_msi_irq().
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Michal Simek <michal.simek@xilinx.com>
CC: linux-arm-kernel@lists.infradead.org
Remove unused __write_msi_msg() and write_msi_msg().
These were added by 83a18912b0 ("PCI/MSI: Rename write_msi_msg() to
pci_write_msi_msg()"), they served their purpose, and they're no longer
needed.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Jiang Liu <jiang.liu@linux.intel.com> # 83a18912b0 author
Change addrconf_f6i_alloc to generate a fib6_config and call
ip6_route_info_create. addrconf_f6i_alloc is the last caller to
fib6_info_alloc besides ip6_route_info_create, and there is no
reason for it to do its own initialization on a fib6_info.
Host routes need to be created even if the device is down, so add a
new flag, fc_ignore_dev_down, to fib6_config and update fib6_nh_init
to not error out if device is not up.
Notes on the conversion:
- ip_fib_metrics_init is the same as fib6_config has fc_mx set to NULL
and fc_mx_len set to 0
- dst_nocount is handled by the RTF_ADDRCONF flag
- dst_host is handled by fc_dst_len = 128
nh_gw does not get set after the conversion to ip6_route_info_create
but it should not be set in addrconf_f6i_alloc since this is a host
route not a gateway route.
Everything else is a straight forward map between fib6_info and
fib6_config.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Keep generic names, as there are no conflicts with previous
SFR definitions.
While touching bits, update AT91_OHCIICR_USB_SUSPEND to use
GENMASK, replace unused AT91_OHCIICR_SUSPEND_A/B/C with a more
generic macro, align values on tab-width.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Make use of the spi-mem direct mapping API to let advanced controllers
optimize read/write operations when they support direct mapping.
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Stefan Roese <sr@denx.de>
The regulator header has empty inline functions for most interfaces,
but not regulator_get_linear_step(), which has just grown a user
that does not depend on regulators otherwise:
drivers/clk/tegra/clk-tegra124-dfll-fcpu.c: In function 'get_alignment_from_regulator':
drivers/clk/tegra/clk-tegra124-dfll-fcpu.c:555:19: error: implicit declaration of function 'regulator_get_linear_step'; did you mean 'regulator_get_drvdata'? [-Werror=implicit-function-declaration]
align->step_uv = regulator_get_linear_step(reg);
^~~~~~~~~~~~~~~~~~~~~~~~~
regulator_get_drvdata
cc1: all warnings being treated as errors
scripts/Makefile.build:278: recipe for target 'drivers/clk/tegra/clk-tegra124-dfll-fcpu.o' failed
Add the missing stub along the others.
Fixes: b3cf8d0695 ("clk: tegra: dfll: CVB calculation alignment with the regulator")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current simple-card-utils is using asoc_simple_card_xxx() for each
function naming, but it is very verbose.
Thus it is easy to be over 80 char.
This patch renames it to asoc_simple_xxx().
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The difference between simple-card / audio-graph are just using
OF graph style, or not. In other words, other things should be same.
This means, simple-card/audio-graph common functions should be
implemented at simple-card-utils, and its own functions should be
implemented at each files.
Current simple-card / audio-graph are using
asoc_simple_card_parse_dai() which is different implementation.
But, these are implemanted at simple-card-utils.
It should be implemanted at each files.
This patch separate these into each files.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The difference between simple-card / audio-graph are just using
OF graph style, or not. In other words, other things should be same.
This means, simple-card/audio-graph common functions should be
implemented at simple-card-utils, and its own functions should be
implemented at each files.
Current simple-card / audio-graph are initializing each priv,
but it is same operation.
This patch adds new asoc_simple_card_init_priv() and initialize
priv by same operation.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The difference between simple-card / audio-graph are just using
OF graph style, or not. In other words, other things should be same.
This means, simple-card/audio-graph common functions should be
implemented at simple-card-utils, and its own functions should be
implemented at each files.
Current simple-card / audio-graph have almost same functions.
This patch shares asoc_simple_be_hw_params_fixup() between in these
2 drivers.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The difference between simple-card / audio-graph are just using
OF graph style, or not. In other words, other things should be same.
This means, simple-card/audio-graph common functions should be
implemented at simple-card-utils, and its own functions should be
implemented at each files.
Current simple-card / audio-graph have almost same functions.
This patch shares asoc_simple_dai_init() between in these 2 drivers.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The difference between simple-card / audio-graph are just using
OF graph style, or not. In other words, other things should be same.
This means, simple-card/audio-graph common functions should be
implemented at simple-card-utils, and its own functions should be
implemented at each files.
Current simple-card / audio-graph have almost same functions.
This patch shares asoc_simple_hw_param() between in these 2 drivers.
One note is that only simple-card supports simple_set_clk_rate()
at hw_param from commit e9be4ffd4f ("ASoC: simple-card: set cpu
dai clk in hw_params").
By this patch, audio-graph has same feature.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The difference between simple-card / audio-graph are just using
OF graph style, or not. In other words, other things should be same.
This means, simple-card/audio-graph common functions should be
implemented at simple-card-utils, and its own functions should be
implemented at each files.
Current simple-card / audio-graph have almost same functions.
This patch shares asoc_simple_shutdown() between in these 2 drivers.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The difference between simple-card / audio-graph are just using
OF graph style, or not. In other words, other things should be same.
This means, simple-card/audio-graph common functions should be
implemented at simple-card-utils, and its own functions should be
implemented at each files.
Current simple-card / audio-graph have almost same functions.
This patch shares asoc_simple_startup() between in these 2 drivers.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Historically, simple-card/simple-scu-card/audio-graph/audio-graph-scu
are similar but different generic sound card.
simple-scu-card which was for DPCM was merged into simple-card, and
audio-graph-scu which was for DPCM was merged into audio-graph.
simple-card is for non OF graph sound card, and
audio-graph is for OF graph sound card.
And, small detail difference (= function parameter, naming, etc)
between simple-card/audio-graph has been unified.
So today, the difference between simple-card/audio-graph are
just using OF graph style, or not.
In other words, there should no difference other than OF graph sytle.
simple-card/audio-graph are using own priv today , but we can merge it.
This patch merge it at simple_card_utils.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current simple-card-utils has dev_dbg(), but people want to
add #define DEBUG at simple-card/audio-graph, not simple-card-utils.
And, people want to get all information.
This patch adds new asoc_simple_debug_info() to indicates information.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
For the purposes of platforms which use the codec as DAI clock
master for the CPU and other codec devices, there is the need to
not only expose the clock gating of BCLK and WCLK but also the
ability to set those rates without going through the ASoC APIs.
To make this possible, the previous CCF implementation in the
driver has been extended to separate BCLK and WCLK out. WCLK is
the parent clock to BCLK, and is also the clock gate for both.
BCLK in HW is a factor/multiplier of WCLK so derives from whatever
SR is chosen for WCLK, hence the need to make it a child of WCLK
for the purposes of CCF. Enabling/disabling either BCLK or WCLK
will result in clocks being ungated/gated accordingly. To simplify
matters, these clocks can only be configured if the codec is set
as master, otherwise CCF control is disallowed.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch introduces a new security hook that is intended for
initializing the security data for newly created kernfs nodes, which
provide a way of storing a non-default security context, but need to
operate independently from mounts (and therefore may not have an
associated inode at the moment of creation).
The main motivation is to allow kernfs nodes to inherit the context of
the parent under SELinux, similar to the behavior of
security_inode_init_security(). Other LSMs may implement their own logic
for handling the creation of new nodes.
This patch also adds helper functions to <linux/kernfs.h> for
getting/setting security xattrs of a kernfs node so that LSMs hooks are
able to do their job. Other important attributes should be accessible
direcly in the kernfs_node fields (in case there is need for more, then
new helpers should be added to kernfs.h along with the patch that needs
them).
Signed-off-by: Ondrej Mosnacek <omosnace@redhat.com>
Acked-by: Casey Schaufler <casey@schaufler-ca.com>
[PM: more manual merge fixes]
Signed-off-by: Paul Moore <paul@paul-moore.com>
syscall_get_arch() is required to be implemented on all architectures
in addition to already implemented syscall_get_nr(),
syscall_get_arguments(), syscall_get_error(), and
syscall_get_return_value() functions in order to extend the generic
ptrace API with PTRACE_GET_SYSCALL_INFO request.
Acked-by: Paul Moore <paul@paul-moore.com>
Cc: Elvira Khabirova <lineprinter@altlinux.org>
Cc: Eugene Syromyatnikov <esyr@redhat.com>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: linux-audit@redhat.com
Signed-off-by: Dmitry V. Levin <ldv@altlinux.org>
Signed-off-by: Paul Moore <paul@paul-moore.com>
This should never have been defined in the arch tree to begin with,
and now uapi/linux/audit.h header is going to use EM_UNICORE
in order to define AUDIT_ARCH_UNICORE which is needed to implement
syscall_get_arch() which in turn is required to extend
the generic ptrace API with PTRACE_GET_SYSCALL_INFO request.
Acked-by: Paul Moore <paul@paul-moore.com>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Elvira Khabirova <lineprinter@altlinux.org>
Cc: Eugene Syromyatnikov <esyr@redhat.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: linux-audit@redhat.com
Signed-off-by: Dmitry V. Levin <ldv@altlinux.org>
Signed-off-by: Paul Moore <paul@paul-moore.com>
In addition to icmp_echo_ignore_multicast, there is a need to also
prevent responding to pings to anycast addresses for security.
Signed-off-by: Stephen Suryaputra <ssuryaextr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Provide an fspick() system call that can be used to pick an existing
mountpoint into an fs_context which can thereafter be used to reconfigure a
superblock (equivalent of the superblock side of -o remount).
This looks like:
int fd = fspick(AT_FDCWD, "/mnt",
FSPICK_CLOEXEC | FSPICK_NO_AUTOMOUNT);
fsconfig(fd, FSCONFIG_SET_FLAG, "intr", NULL, 0);
fsconfig(fd, FSCONFIG_SET_FLAG, "noac", NULL, 0);
fsconfig(fd, FSCONFIG_CMD_RECONFIGURE, NULL, NULL, 0);
At the point of fspick being called, the file descriptor referring to the
filesystem context is in exactly the same state as the one that was created
by fsopen() after fsmount() has been successfully called.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: linux-api@vger.kernel.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Provide a system call by which a filesystem opened with fsopen() and
configured by a series of fsconfig() calls can have a detached mount object
created for it. This mount object can then be attached to the VFS mount
hierarchy using move_mount() by passing the returned file descriptor as the
from directory fd.
The system call looks like:
int mfd = fsmount(int fsfd, unsigned int flags,
unsigned int attr_flags);
where fsfd is the file descriptor returned by fsopen(). flags can be 0 or
FSMOUNT_CLOEXEC. attr_flags is a bitwise-OR of the following flags:
MOUNT_ATTR_RDONLY Mount read-only
MOUNT_ATTR_NOSUID Ignore suid and sgid bits
MOUNT_ATTR_NODEV Disallow access to device special files
MOUNT_ATTR_NOEXEC Disallow program execution
MOUNT_ATTR__ATIME Setting on how atime should be updated
MOUNT_ATTR_RELATIME - Update atime relative to mtime/ctime
MOUNT_ATTR_NOATIME - Do not update access times
MOUNT_ATTR_STRICTATIME - Always perform atime updates
MOUNT_ATTR_NODIRATIME Do not update directory access times
In the event that fsmount() fails, it may be possible to get an error
message by calling read() on fsfd. If no message is available, ENODATA
will be reported.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: linux-api@vger.kernel.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Add a syscall for configuring a filesystem creation context and triggering
actions upon it, to be used in conjunction with fsopen, fspick and fsmount.
long fsconfig(int fs_fd, unsigned int cmd, const char *key,
const void *value, int aux);
Where fs_fd indicates the context, cmd indicates the action to take, key
indicates the parameter name for parameter-setting actions and, if needed,
value points to a buffer containing the value and aux can give more
information for the value.
The following command IDs are proposed:
(*) FSCONFIG_SET_FLAG: No value is specified. The parameter must be
boolean in nature. The key may be prefixed with "no" to invert the
setting. value must be NULL and aux must be 0.
(*) FSCONFIG_SET_STRING: A string value is specified. The parameter can
be expecting boolean, integer, string or take a path. A conversion to
an appropriate type will be attempted (which may include looking up as
a path). value points to a NUL-terminated string and aux must be 0.
(*) FSCONFIG_SET_BINARY: A binary blob is specified. value points to
the blob and aux indicates its size. The parameter must be expecting
a blob.
(*) FSCONFIG_SET_PATH: A non-empty path is specified. The parameter must
be expecting a path object. value points to a NUL-terminated string
that is the path and aux is a file descriptor at which to start a
relative lookup or AT_FDCWD.
(*) FSCONFIG_SET_PATH_EMPTY: As fsconfig_set_path, but with AT_EMPTY_PATH
implied.
(*) FSCONFIG_SET_FD: An open file descriptor is specified. value must
be NULL and aux indicates the file descriptor.
(*) FSCONFIG_CMD_CREATE: Trigger superblock creation.
(*) FSCONFIG_CMD_RECONFIGURE: Trigger superblock reconfiguration.
For the "set" command IDs, the idea is that the file_system_type will point
to a list of parameters and the types of value that those parameters expect
to take. The core code can then do the parse and argument conversion and
then give the LSM and FS a cooked option or array of options to use.
Source specification is also done the same way same way, using special keys
"source", "source1", "source2", etc..
[!] Note that, for the moment, the key and value are just glued back
together and handed to the filesystem. Every filesystem that uses options
uses match_token() and co. to do this, and this will need to be changed -
but not all at once.
Example usage:
fd = fsopen("ext4", FSOPEN_CLOEXEC);
fsconfig(fd, fsconfig_set_path, "source", "/dev/sda1", AT_FDCWD);
fsconfig(fd, fsconfig_set_path_empty, "journal_path", "", journal_fd);
fsconfig(fd, fsconfig_set_fd, "journal_fd", "", journal_fd);
fsconfig(fd, fsconfig_set_flag, "user_xattr", NULL, 0);
fsconfig(fd, fsconfig_set_flag, "noacl", NULL, 0);
fsconfig(fd, fsconfig_set_string, "sb", "1", 0);
fsconfig(fd, fsconfig_set_string, "errors", "continue", 0);
fsconfig(fd, fsconfig_set_string, "data", "journal", 0);
fsconfig(fd, fsconfig_set_string, "context", "unconfined_u:...", 0);
fsconfig(fd, fsconfig_cmd_create, NULL, NULL, 0);
mfd = fsmount(fd, FSMOUNT_CLOEXEC, MS_NOEXEC);
or:
fd = fsopen("ext4", FSOPEN_CLOEXEC);
fsconfig(fd, fsconfig_set_string, "source", "/dev/sda1", 0);
fsconfig(fd, fsconfig_cmd_create, NULL, NULL, 0);
mfd = fsmount(fd, FSMOUNT_CLOEXEC, MS_NOEXEC);
or:
fd = fsopen("afs", FSOPEN_CLOEXEC);
fsconfig(fd, fsconfig_set_string, "source", "#grand.central.org:root.cell", 0);
fsconfig(fd, fsconfig_cmd_create, NULL, NULL, 0);
mfd = fsmount(fd, FSMOUNT_CLOEXEC, MS_NOEXEC);
or:
fd = fsopen("jffs2", FSOPEN_CLOEXEC);
fsconfig(fd, fsconfig_set_string, "source", "mtd0", 0);
fsconfig(fd, fsconfig_cmd_create, NULL, NULL, 0);
mfd = fsmount(fd, FSMOUNT_CLOEXEC, MS_NOEXEC);
Signed-off-by: David Howells <dhowells@redhat.com>
cc: linux-api@vger.kernel.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Implement the ability for filesystems to log error, warning and
informational messages through the fs_context. These can be extracted by
userspace by reading from an fd created by fsopen().
Error messages are prefixed with "e ", warnings with "w " and informational
messages with "i ".
Inside the kernel, formatted messages are malloc'd but unformatted messages
are not copied if they're either in the core .rodata section or in the
.rodata section of the filesystem module pinned by fs_context::fs_type.
The messages are only good till the fs_type is released.
Note that the logging object is shared between duplicated fs_context
structures. This is so that such as NFS which do a mount within a mount
can get at least some of the errors from the inner mount.
Five logging functions are provided for this:
(1) void logfc(struct fs_context *fc, const char *fmt, ...);
This logs a message into the context. If the buffer is full, the
earliest message is discarded.
(2) void errorf(fc, fmt, ...);
This wraps logfc() to log an error.
(3) void invalf(fc, fmt, ...);
This wraps errorf() and returns -EINVAL for convenience.
(4) void warnf(fc, fmt, ...);
This wraps logfc() to log a warning.
(5) void infof(fc, fmt, ...);
This wraps logfc() to log an informational message.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Provide an fsopen() system call that starts the process of preparing to
create a superblock that will then be mountable, using an fd as a context
handle. fsopen() is given the name of the filesystem that will be used:
int mfd = fsopen(const char *fsname, unsigned int flags);
where flags can be 0 or FSOPEN_CLOEXEC.
For example:
sfd = fsopen("ext4", FSOPEN_CLOEXEC);
fsconfig(sfd, FSCONFIG_SET_PATH, "source", "/dev/sda1", AT_FDCWD);
fsconfig(sfd, FSCONFIG_SET_FLAG, "noatime", NULL, 0);
fsconfig(sfd, FSCONFIG_SET_FLAG, "acl", NULL, 0);
fsconfig(sfd, FSCONFIG_SET_FLAG, "user_xattr", NULL, 0);
fsconfig(sfd, FSCONFIG_SET_STRING, "sb", "1", 0);
fsconfig(sfd, FSCONFIG_CMD_CREATE, NULL, NULL, 0);
fsinfo(sfd, NULL, ...); // query new superblock attributes
mfd = fsmount(sfd, FSMOUNT_CLOEXEC, MS_RELATIME);
move_mount(mfd, "", sfd, AT_FDCWD, "/mnt", MOVE_MOUNT_F_EMPTY_PATH);
sfd = fsopen("afs", -1);
fsconfig(fd, FSCONFIG_SET_STRING, "source",
"#grand.central.org:root.cell", 0);
fsconfig(fd, FSCONFIG_CMD_CREATE, NULL, NULL, 0);
mfd = fsmount(sfd, 0, MS_NODEV);
move_mount(mfd, "", sfd, AT_FDCWD, "/mnt", MOVE_MOUNT_F_EMPTY_PATH);
If an error is reported at any step, an error message may be available to be
read() back (ENODATA will be reported if there isn't an error available) in
the form:
"e <subsys>:<problem>"
"e SELinux:Mount on mountpoint not permitted"
Once fsmount() has been called, further fsconfig() calls will incur EBUSY,
even if the fsmount() fails. read() is still possible to retrieve error
information.
The fsopen() syscall creates a mount context and hangs it of the fd that it
returns.
Netlink is not used because it is optional and would make the core VFS
dependent on the networking layer and also potentially add network
namespace issues.
Note that, for the moment, the caller must have SYS_CAP_ADMIN to use
fsopen().
Signed-off-by: David Howells <dhowells@redhat.com>
cc: linux-api@vger.kernel.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Add a move_mount() system call that will move a mount from one place to
another and, in the next commit, allow to attach an unattached mount tree.
The new system call looks like the following:
int move_mount(int from_dfd, const char *from_path,
int to_dfd, const char *to_path,
unsigned int flags);
Signed-off-by: David Howells <dhowells@redhat.com>
cc: linux-api@vger.kernel.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
open_tree(dfd, pathname, flags)
Returns an O_PATH-opened file descriptor or an error.
dfd and pathname specify the location to open, in usual
fashion (see e.g. fstatat(2)). flags should be an OR of
some of the following:
* AT_PATH_EMPTY, AT_NO_AUTOMOUNT, AT_SYMLINK_NOFOLLOW -
same meanings as usual
* OPEN_TREE_CLOEXEC - make the resulting descriptor
close-on-exec
* OPEN_TREE_CLONE or OPEN_TREE_CLONE | AT_RECURSIVE -
instead of opening the location in question, create a detached
mount tree matching the subtree rooted at location specified by
dfd/pathname. With AT_RECURSIVE the entire subtree is cloned,
without it - only the part within in the mount containing the
location in question. In other words, the same as mount --rbind
or mount --bind would've taken. The detached tree will be
dissolved on the final close of obtained file. Creation of such
detached trees requires the same capabilities as doing mount --bind.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David Howells <dhowells@redhat.com>
cc: linux-api@vger.kernel.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
For q->poll_nsec == -1, means doing classic poll, not hybrid poll.
We introduce a new flag BLK_MQ_POLL_CLASSIC to replace -1, which
may make code much easier to read.
Additionally, since val is an int obtained with kstrtoint(), val can be
a negative value other than -1, so return -EINVAL for that case.
Thanks to Damien Le Moal for some good suggestion.
Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Yufen Yu <yuyufen@huawei.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
After the previous patch, all the callers of ndo_select_queue()
provide as a 'fallback' argument netdev_pick_tx.
The only exceptions are nested calls to ndo_select_queue(),
which pass down the 'fallback' available in the current scope
- still netdev_pick_tx.
We can drop such argument and replace fallback() invocation with
netdev_pick_tx(). This avoids an indirect call per xmit packet
in some scenarios (TCP syn, UDP unconnected, XDP generic, pktgen)
with device drivers implementing such ndo. It also clean the code
a bit.
Tested with ixgbe and CONFIG_FCOE=m
With pktgen using queue xmit:
threads vanilla patched
(kpps) (kpps)
1 2334 2428
2 4166 4278
4 7895 8100
v1 -> v2:
- rebased after helper's name change
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
