We've been artificially limiting the size of our queues to 4k so that we
don't end up allocating huge amounts of physically-contiguous memory at
probe time. However, 4k is only enough for 256 commands in the command
queue, so instead let's try to allocate the largest queue that the SMMU
supports, retrying with a smaller size if the allocation fails.
The caveat here is that we have to limit our upper bound based on
CONFIG_CMA_ALIGNMENT to ensure that our queue allocations remain
natually aligned, which is required by the SMMU architecture.
Signed-off-by: Will Deacon <will.deacon@arm.com>
In sock_getsockopt(), 'optlen' is fetched the first time from userspace.
'len < 0' is then checked. Then in condition 'SO_MEMINFO', 'optlen' is
fetched the second time from userspace.
If change it between two fetches may cause security problems or unexpected
behaivor, and there is no reason to fetch it a second time.
To fix this, we need to remove the second fetch.
Signed-off-by: JingYi Hou <houjingyi647@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It appears that a FAILOVER_MSG can come from peer even when the failure
link is resetting (i.e. just after the 'node_write_unlock()'...). This
means the failover procedure on the node has not been started yet.
The situation is as follows:
node1 node2
linkb linka linka linkb
| | | |
| | x failure |
| | RESETTING |
| | | |
| x failure RESET |
| RESETTING FAILINGOVER |
| | (FAILOVER_MSG) | |
|<-------------------------------------------------|
| *FAILINGOVER | | |
| | (dummy FAILOVER_MSG) | |
|------------------------------------------------->|
| RESET | | FAILOVER_END
| FAILINGOVER RESET |
. . . .
. . . .
. . . .
Once this happens, the link failover procedure will be triggered
wrongly on the receiving node since the node isn't in FAILINGOVER state
but then another link failover will be carried out.
The consequences are:
1) A peer might get stuck in FAILINGOVER state because the 'sync_point'
was set, reset and set incorrectly, the criteria to end the failover
would not be met, it could keep waiting for a message that has already
received.
2) The early FAILOVER_MSG(s) could be queued in the link failover
deferdq but would be purged or not pulled out because the 'drop_point'
was not set correctly.
3) The early FAILOVER_MSG(s) could be dropped too.
4) The dummy FAILOVER_MSG could make the peer leaving FAILINGOVER state
shortly, but later on it would be restarted.
The same situation can also happen when the link is in PEER_RESET state
and a FAILOVER_MSG arrives.
The commit resolves the issues by forcing the link down immediately, so
the failover procedure will be started normally (which is the same as
when receiving a FAILOVER_MSG and the link is in up state).
Also, the function "tipc_node_link_failover()" is toughen to avoid such
a situation from happening.
Acked-by: Jon Maloy <jon.maloy@ericsson.se>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some transceivers may comply with SFF-8472 even though they do not
implement the Digital Diagnostic Monitoring (DDM) interface described in
the spec. The existence of such area is specified by the 6th bit of byte
92, set to 1 if implemented.
Currently, without checking this bit, bnx2x fails trying to read sfp
module's EEPROM with the follow message:
ethtool -m enP5p1s0f1
Cannot get Module EEPROM data: Input/output error
Because it fails to read the additional 256 bytes in which it is assumed
to exist the DDM data.
This issue was noticed using a Mellanox Passive DAC PN 01FT738. The EEPROM
data was confirmed by Mellanox as correct and similar to other Passive
DACs from other manufacturers.
Signed-off-by: Mauro S. M. Rodrigues <maurosr@linux.vnet.ibm.com>
Acked-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel says:
====================
mlxsw: Improve IPv6 route insertion rate
Unlike IPv4, an IPv6 multipath route in the kernel is composed from
multiple sibling routes, each representing a single nexthop.
Therefore, an addition of a multipath route with N nexthops translates
to N in-kernel notifications. This is inefficient for device drivers
that need to program the route to the underlying device. Each time a new
nexthop is appended, a new nexthop group needs to be constructed and the
old one deleted.
This patchset improves the situation by sending a single notification
for a multipath route addition / deletion instead of one per-nexthop.
When adding thousands of multipath routes with 16 nexthops, I measured
an improvement of about x10 in the insertion rate.
Patches #1-#3 add a flag that indicates that in-kernel notifications
need to be suppressed and extend the IPv6 FIB notification info with
information about the number of sibling routes that are being notified.
Patches #4-#5 adjust the two current listeners to these notifications to
ignore notifications about IPv6 multipath routes.
Patches #6-#7 adds add / delete notifications for IPv6 multipath routes.
Patches #8-#14 do the same for mlxsw.
Patch #15 finally removes the limitations added in patches #4-#5 and
stops the kernel from sending a notification for each added / deleted
nexthop.
Patch #16 adds test cases.
v2 (David Ahern):
* Remove patch adjusting netdevsim to consume resources for each
fib6_info. Instead, consume one resource for the entire multipath
route
* Remove 'multipath_rt' usage in patch #10
* Remove 'multipath_rt' from 'struct fib6_entry_notifier_info' in patch
#15. The member is only removed in this patch to prevent drivers from
processing multipath routes twice during the series
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Test that the offload indication for unicast routes is correctly set in
different scenarios. IPv4 support will be added in the future.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both listeners - mlxsw and netdevsim - of IPv6 FIB notifications are now
ready to handle IPv6 multipath notifications.
Therefore, stop ignoring such notifications in both drivers and stop
sending notification for each added / deleted nexthop.
v2:
* Remove 'multipath_rt' from 'struct fib6_entry_notifier_info'
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow the driver to create an IPv6 multipath route in one go by passing
an array of sibling routes and iterating over them.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the functions that take care of populating IPv6 nexthop
groups only add / delete a single nexthop.
Prepare them to handle multiple routes in one notification by passing an
array of routes and adding / deleting all of them.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prepare the driver to handle multiple routes in a single notification by
passing an array of routes to the functions that actually add / delete a
route.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously, IPv6 replace notifications were only sent from
fib6_add_rt2node(). The function only emitted such notifications if a
route actually replaced another route.
A previous patch added another call site in ip6_route_multipath_add()
from which such notification can be emitted even if a route was merely
added and did not replace another route.
Adjust the driver to take this into account and potentially set the
'replace' flag to 'false' if the notified route did not replace an
existing route.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prepare the driver to process IPv6 multipath notifications by passing an
array of 'struct fib6_info' instead of just one route.
A reference is taken on each sibling route in order to prevent them from
being freed until they are processed by the workqueue.
v2:
* Remove 'multipath_rt' usage
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function mlxsw_sp_router_fib6_event() takes care of preparing the
needed information for the work item that actually inserts the route
into the device.
When processing an IPv6 multipath route, the function will need to
allocate an array to store pointers to all the sibling routes.
Change the function's signature to return an error code and adjust the
single call site.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If all the nexthops of a multipath route are being deleted, send one
notification for the entire route, instead of one per-nexthop.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Emit a notification when a multipath routes is added or replace.
Note that unlike the replace notifications sent from fib6_add_rt2node(),
it is possible we are sending a 'FIB_EVENT_ENTRY_REPLACE' when a route
was merely added and not replaced.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a similar fashion to previous patch, have netdevsim ignore IPv6
multipath notifications for now.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPv6 multipath notifications are about to be sent, but mlxsw is not
ready to process them, so ignore them.
The limitation will be lifted by a subsequent patch which will also stop
the kernel from sending a notification for each nexthop.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend the IPv6 FIB notifier info with number of sibling routes being
notified.
This will later allow listeners to process one notification for a
multipath routes instead of N, where N is the number of nexthops.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The struct includes a 'skip_notify' flag that indicates if netlink
notifications to user space should be suppressed. As explained in commit
3b1137fe74 ("net: ipv6: Change notifications for multipath add to
RTA_MULTIPATH"), this is useful to suppress per-nexthop RTM_NEWROUTE
notifications when an IPv6 multipath route is added / deleted. Instead,
one notification is sent for the entire multipath route.
This concept is also useful for in-kernel notifications. Sending one
in-kernel notification for the addition / deletion of an IPv6 multipath
route - instead of one per-nexthop - provides a significant increase in
the insertion / deletion rate to underlying devices.
Add a 'skip_notify_kernel' flag to suppress in-kernel notifications.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2019-06-17
This series contains updates to the iavf driver only.
Akeem updates the driver to change how VLAN tags are being populated and
programmed into the hardware by starting from the first member of the
list until the number of allowed VLAN tags is exhausted.
Mitch fixed the variable type since the variable counter starts out
negative and climbs to zero, so use a signed integer instead of
unsigned. Also increase the timeout to avoid erroneous errors. Fixed
the driver to be able to handle when the hardware hands us a null
receive descriptor with no data attached, yet is still valid.
Aleksandr fixes the driver to use GFP_ATOMIC when allocating memory in
atomic context.
Avinash updates the driver to fix a calculation error in virtchnl
regarding the valid length.
Jakub does some refactoring of the commands processing the watchdog
state machine to reduce the length and complexity of the function. Also
decalre watchdog task as delayed work and use a dedicated work queue to
service the driver tasks.
Paul updated the iavf_process_aq_command to call the necessary functions
to be able to clear cloud filter bits that need to be cleared.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
USB 3.2 capability in a host can be detected from the
xHCI Supported Protocol Capability major and minor revision fields.
If major is 0x3 and minor 0x20 then the host is USB 3.2 capable.
For USB 3.2 capable hosts set the root hub lane count to 2.
The Major Revision and Minor Revision fields contain a BCD version number.
The value of the Major Revision field is JJh and the value of the Minor
Revision field is MNh for version JJ.M.N, where JJ = major revision number,
M - minor version number, N = sub-minor version number,
e.g. version 3.1 is represented with a value of 0310h.
Also fix the extra whitespace printed out when announcing regular
SuperSpeed hosts.
Cc: <stable@vger.kernel.org> # v4.18+
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A USB3 device needs to be reset and re-enumarated if the port it
connects to goes to a error state, with link state inactive.
There is no use in trying to recover failed transactions by resetting
endpoints at this stage. Tests show that in rare cases, after multiple
endpoint resets of a roothub port the whole host controller might stop
completely.
Several retries to recover from transaction error can happen as
it can take a long time before the hub thread discovers the USB3
port error and inactive link.
We can't reliably detect the port error from slot or endpoint context
due to a limitation in xhci, see xhci specs section 4.8.3:
"There are several cases where the EP State field in the Output
Endpoint Context may not reflect the current state of an endpoint"
and
"Software should maintain an accurate value for EP State, by tracking it
with an internal variable that is driven by Events and Doorbell accesses"
Same appears to be true for slot state.
set a flag to the corresponding slot if a USB3 roothub port link goes
inactive to prevent both queueing new URBs and resetting endpoints.
Reported-by: Rapolu Chiranjeevi <chiranjeevi.rapolu@intel.com>
Tested-by: Rapolu Chiranjeevi <chiranjeevi.rapolu@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Compilation on 32-bit ARM fails after commit 992aa864dc ("mlxsw:
spectrum_ptp: Add implementation for physical hardware clock operations")
because of 64-bit division:
arm-linux-gnueabi-ld:
drivers/net/ethernet/mellanox/mlxsw/spectrum_ptp.o: in function
`mlxsw_sp1_ptp_phc_settime': spectrum_ptp.c:(.text+0x39c): undefined
reference to `__aeabi_uldivmod'
Fix by using div_u64().
Fixes: 992aa864dc ("mlxsw: spectrum_ptp: Add implementation for physical hardware clock operations")
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The documentation mentions a non-existing capability KVM_CAP_USER_MEM.s
The right name is KVM_CAP_USER_MEMORY.
Signed-off-by: Dennis Restle <derestle@htwg-konstanz.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Every merge window seems to involve at least one episode where subsystem
maintainers don't manage their trees as Linus would like. Document the
expectations so that at least he has something to point people to.
Acked-by: David Rientjes <rientjes@google.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
The commit "iommu/vt-d: Probe DMA-capable ACPI name space devices"
introduced a compilation warning due to the "iommu" variable in
for_each_active_iommu() but never used the for each element, i.e,
"drhd->iommu".
drivers/iommu/intel-iommu.c: In function 'probe_acpi_namespace_devices':
drivers/iommu/intel-iommu.c:4639:22: warning: variable 'iommu' set but
not used [-Wunused-but-set-variable]
struct intel_iommu *iommu;
Silence the warning the same way as in the commit d3ed71e5cc
("drivers/iommu/intel-iommu.c: fix variable 'iommu' set but not used")
Signed-off-by: Qian Cai <cai@lca.pw>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
The linux-next commit "iommu/vt-d: Duplicate iommu_resv_region objects
per device list" [1] left out an unused variable,
drivers/iommu/intel-iommu.c: In function 'dmar_parse_one_rmrr':
drivers/iommu/intel-iommu.c:4014:9: warning: variable 'length' set but
not used [-Wunused-but-set-variable]
[1] https://lore.kernel.org/patchwork/patch/1083073/
Signed-off-by: Qian Cai <cai@lca.pw>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
On 32-bit architectures, phys_addr_t may be different from dma_add_t,
both smaller and bigger. This can lead to an overflow during an assignment
that clang warns about:
drivers/iommu/dma-iommu.c:230:10: error: implicit conversion from 'dma_addr_t' (aka 'unsigned long long') to
'phys_addr_t' (aka 'unsigned int') changes value from 18446744073709551615 to 4294967295 [-Werror,-Wconstant-conversion]
Use phys_addr_t here because that is the type that the variable was
declared as.
Fixes: aadad097cd ("iommu/dma: Reserve IOVA for PCIe inaccessible DMA address")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Expose performance counters through 2 driver specific ioctls: one to
enable/disable the perfcnt block, and one to dump the counter values.
There are discussions to expose global performance monitors (those
counters that can't be retrieved on a per-job basis) in a consistent
way, but this is likely to take time to settle on something that works
for various HW/users.
The ioctls are marked unstable so we can get rid of them when the time
comes. We initally went for a debugfs-based interface, but this was
making the transition to per-FD address space more complicated (we need
to specify the namespace the GPU has to use when dumping the perf
counters), hence the decision to switch back to driver specific ioctls
which are passed the FD they operate on and thus will have a dedicated
address space attached to them.
Other than that, the implementation is pretty simple: it basically dumps
all counters and copy the values to a userspace buffer. The parsing is
left to userspace which has to know the specific layout that's used
by the GPU (layout differs on a per-revision basis).
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Acked-by: Alyssa Rosenzweig <alyssa@rosenzweig.io>
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190618081648.17297-5-boris.brezillon@collabora.com
We plan to expose performance counters through 2 driver specific
ioctls until there's a solution to expose them in a generic way.
In order to be able to deprecate those ioctls when this new
infrastructure is in place we add an unsafe module parameter that
will keep those ioctls hidden unless it's set to true (which also
has the effect of tainting the kernel).
All unstable ioctl handlers should use panfrost_unstable_ioctl_check()
to check whether they're supposed to handle the request or reject it
with ENOSYS.
Suggested-by: Emil Velikov <emil.velikov@collabora.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Alyssa Rosenzweig <alyssa@rosenzweig.io>
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190618081648.17297-3-boris.brezillon@collabora.com
Ease future extensions of struct iommu_fault_page_request and struct
iommu_fault_unrecoverable by adding a few bytes of padding. That way, a
new field can be added to either of these structures by simply introducing
a new flag. To extend it after the size limit is reached, a new fault
reporting structure will have to be negotiated with userspace.
With 56 bytes of padding, the total size of iommu_fault is 64 bytes and
fits in a cache line on a lot of contemporary machines, while providing 16
and 24 bytes of extension to structures iommu_fault_page_request and
iommu_fault_unrecoverable respectively.
Signed-off-by: Jean-Philippe Brucker <jean-philippe.brucker@arm.com>
Acked-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Range functions like hmm_range_snapshot() and hmm_range_fault() call
find_vma, which requires hodling the mmget() and the mmap_sem for the mm.
Make this simpler for the callers by holding the mmget() inside the range
for the lifetime of the range. Other functions that accept a range should
only be called if the range is registered.
This has the side effect of directly preventing hmm_release() from
happening while a range is registered. That means range->dead cannot be
false during the lifetime of the range, so remove dead and
hmm_mirror_mm_is_alive() entirely.
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Reviewed-by: John Hubbard <jhubbard@nvidia.com>
Reviewed-by: Ralph Campbell <rcampbell@nvidia.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Tested-by: Philip Yang <Philip.Yang@amd.com>
