Add link modes for 100Mbps and 1Gbps over a single pair.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver would only set the IO impedance value when RGMII internal
delays were enabled. There is no reason for this. Move the IO
impedance block out of the RGMII delay block.
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The variables used to store u32 DT properties were signed ints. This
doesn't work properly if the value of the property were to overflow.
Use unsigned variables so this doesn't happen.
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code was assuming the reset default of the delay control register
was to have delay disabled. This is what the datasheet shows as the
register's initial value. However, that's not actually true: the
default is controlled by the PHY's pin strapping.
If the interface mode is selected as RX or TX delay only, insure the
other direction's delay is disabled.
If the interface mode is just "rgmii", with neither TX or RX internal
delay, one might expect that the driver should disable both delays. But
this is not what the driver does. It leaves the setting at the PHY's
strapping's default. And that default, for no pins with strapping
resistors, is to have delay enabled and 2.00 ns.
Rather than change this behavior, I've kept it the same and documented
it. No delay will most likely not work and will break ethernet on any
board using "rgmii" mode. If the board is strapped to have a delay and
is configured to use "rgmii" mode a warning is generated that "rgmii-id"
should have been used.
Also validate the delay values and fail if they are not in range.
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Generally, the output clock pin is only used for testing and only serves
as a source of RF noise after this. It could be used to daisy-chain
PHYs, but this is uncommon. Since the PHY can disable the output, make
doing so an option. I do this by adding another enumeration to the
allowed values of ti,clk-output-sel.
The code was not using the value DP83867_CLK_O_SEL_REF_CLK as one might
expect: to select the REF_CLK as the output. Rather it meant "keep
clock output setting as is", which, depending on PHY strapping, might
not be outputting REF_CLK.
Change this so DP83867_CLK_O_SEL_REF_CLK means enable REF_CLK output.
Omitting the property will leave the setting as is (which was the
previous behavior in this case).
Out of range values were silently converted into
DP83867_CLK_O_SEL_REF_CLK. Change this so they generate an error.
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The clock output is generally only used for testing and development and
not used to daisy-chain PHYs. It's just a source of RF noise afterward.
Add a mux value for "off". I've added it as another enumeration to the
output property. In the actual PHY, the mux and the output enable are
independently controllable. However, it doesn't seem useful to be able
to describe the mux setting when the output is disabled.
Document that PHY's default setting will be left as is if the property
is omitted.
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a note to make it more clear how the driver behaves when "rgmii" vs
"rgmii-id", "rgmii-idrx", or "rgmii-idtx" interface modes are selected.
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hash (exact-match) filters used for offloading flows share the
same active region resources on the chip with upper layer drivers,
like iw_cxgb4, chcr, etc. Currently, only either Hash filters
or ULDs can use the active region resources, but not both. Hence,
use the new firmware configuration parameters (when available)
to allow both the Hash filters and ULDs to share the
active region simultaneously.
Signed-off-by: Vishal Kulkarni <vishal@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't disable the ipg clock in the regulator error path. The clock is
disable unconditionally two lines below the failed_regulator label.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 984203ceff ("net: stmmac: mdio: remove reset gpio free")
removed the reset gpio free, when the driver is unbinded or rmmod,
we miss the gpio free.
This patch uses managed API to request the reset gpio, so that the
gpio could be freed properly.
Fixes: 984203ceff ("net: stmmac: mdio: remove reset gpio free")
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The user can change the device_name with the IMSETDEVNAME ioctl, but we
need to ensure that the user's name is NUL terminated. Otherwise it
could result in a buffer overflow when we copy the name back to the user
with IMGETDEVINFO ioctl.
I also changed two strcpy() calls which handle the name to strscpy().
Hopefully, there aren't any other ways to create a too long name, but
it's nice to do this as a kernel hardening measure.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SAMA5D2 SoC has a suspend mode where SoC's power is cut off. Due to this
the registers content is lost after a suspend/resume cycle. The current
suspend/resume implementation covers some of these registers. However
there are few which were not treated (e.g. SCRT2 and USRIO). Apart
from this, netdev features are not restored. Treat these issues.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function send_signal was split from __send_signal so that it would
be possible to bypass the namespace logic based upon current[1]. As it
turns out the si_pid and the si_uid fixup are both inappropriate in
the case of kill_pid_usb_asyncio so move that logic into send_signal.
It is difficult to arrange but possible for a signal with an si_code
of SI_TIMER or SI_SIGIO to be sent across namespace boundaries. In
which case tests for when it is ok to change si_pid and si_uid based
on SI_FROMUSER are incorrect. Replace the use of SI_FROMUSER with a
new test has_si_pid_and_used based on siginfo_layout.
Now that the uid fixup is no longer present after expanding
SEND_SIG_NOINFO properly calculate the si_uid that the target
task needs to read.
[1] 7978b567d3 ("signals: add from_ancestor_ns parameter to send_signal()")
Cc: stable@vger.kernel.org
Fixes: 6588c1e3ff ("signals: SI_USER: Masquerade si_pid when crossing pid ns boundary")
Fixes: 6b550f9495 ("user namespace: make signal.c respect user namespaces")
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
The usb support for asyncio encoded one of it's values in the wrong
field. It should have used si_value but instead used si_addr which is
not present in the _rt union member of struct siginfo.
The practical result of this is that on a 64bit big endian kernel
when delivering a signal to a 32bit process the si_addr field
is set to NULL, instead of the expected pointer value.
This issue can not be fixed in copy_siginfo_to_user32 as the usb
usage of the the _sigfault (aka si_addr) member of the siginfo
union when SI_ASYNCIO is set is incompatible with the POSIX and
glibc usage of the _rt member of the siginfo union.
Therefore replace kill_pid_info_as_cred with kill_pid_usb_asyncio a
dedicated function for this one specific case. There are no other
users of kill_pid_info_as_cred so this specialization should have no
impact on the amount of code in the kernel. Have kill_pid_usb_asyncio
take instead of a siginfo_t which is difficult and error prone, 3
arguments, a signal number, an errno value, and an address enconded as
a sigval_t. The encoding of the address as a sigval_t allows the
code that reads the userspace request for a signal to handle this
compat issue along with all of the other compat issues.
Add BUILD_BUG_ONs in kernel/signal.c to ensure that we can now place
the pointer value at the in si_pid (instead of si_addr). That is the
code now verifies that si_pid and si_addr always occur at the same
location. Further the code veries that for native structures a value
placed in si_pid and spilling into si_uid will appear in userspace in
si_addr (on a byte by byte copy of siginfo or a field by field copy of
siginfo). The code also verifies that for a 64bit kernel and a 32bit
userspace the 32bit pointer will fit in si_pid.
I have used the usbsig.c program below written by Alan Stern and
slightly tweaked by me to run on a big endian machine to verify the
issue exists (on sparc64) and to confirm the patch below fixes the issue.
/* usbsig.c -- test USB async signal delivery */
#define _GNU_SOURCE
#include <stdio.h>
#include <fcntl.h>
#include <signal.h>
#include <string.h>
#include <sys/ioctl.h>
#include <unistd.h>
#include <endian.h>
#include <linux/usb/ch9.h>
#include <linux/usbdevice_fs.h>
static struct usbdevfs_urb urb;
static struct usbdevfs_disconnectsignal ds;
static volatile sig_atomic_t done = 0;
void urb_handler(int sig, siginfo_t *info , void *ucontext)
{
printf("Got signal %d, signo %d errno %d code %d addr: %p urb: %p\n",
sig, info->si_signo, info->si_errno, info->si_code,
info->si_addr, &urb);
printf("%s\n", (info->si_addr == &urb) ? "Good" : "Bad");
}
void ds_handler(int sig, siginfo_t *info , void *ucontext)
{
printf("Got signal %d, signo %d errno %d code %d addr: %p ds: %p\n",
sig, info->si_signo, info->si_errno, info->si_code,
info->si_addr, &ds);
printf("%s\n", (info->si_addr == &ds) ? "Good" : "Bad");
done = 1;
}
int main(int argc, char **argv)
{
char *devfilename;
int fd;
int rc;
struct sigaction act;
struct usb_ctrlrequest *req;
void *ptr;
char buf[80];
if (argc != 2) {
fprintf(stderr, "Usage: usbsig device-file-name\n");
return 1;
}
devfilename = argv[1];
fd = open(devfilename, O_RDWR);
if (fd == -1) {
perror("Error opening device file");
return 1;
}
act.sa_sigaction = urb_handler;
sigemptyset(&act.sa_mask);
act.sa_flags = SA_SIGINFO;
rc = sigaction(SIGUSR1, &act, NULL);
if (rc == -1) {
perror("Error in sigaction");
return 1;
}
act.sa_sigaction = ds_handler;
sigemptyset(&act.sa_mask);
act.sa_flags = SA_SIGINFO;
rc = sigaction(SIGUSR2, &act, NULL);
if (rc == -1) {
perror("Error in sigaction");
return 1;
}
memset(&urb, 0, sizeof(urb));
urb.type = USBDEVFS_URB_TYPE_CONTROL;
urb.endpoint = USB_DIR_IN | 0;
urb.buffer = buf;
urb.buffer_length = sizeof(buf);
urb.signr = SIGUSR1;
req = (struct usb_ctrlrequest *) buf;
req->bRequestType = USB_DIR_IN | USB_TYPE_STANDARD | USB_RECIP_DEVICE;
req->bRequest = USB_REQ_GET_DESCRIPTOR;
req->wValue = htole16(USB_DT_DEVICE << 8);
req->wIndex = htole16(0);
req->wLength = htole16(sizeof(buf) - sizeof(*req));
rc = ioctl(fd, USBDEVFS_SUBMITURB, &urb);
if (rc == -1) {
perror("Error in SUBMITURB ioctl");
return 1;
}
rc = ioctl(fd, USBDEVFS_REAPURB, &ptr);
if (rc == -1) {
perror("Error in REAPURB ioctl");
return 1;
}
memset(&ds, 0, sizeof(ds));
ds.signr = SIGUSR2;
ds.context = &ds;
rc = ioctl(fd, USBDEVFS_DISCSIGNAL, &ds);
if (rc == -1) {
perror("Error in DISCSIGNAL ioctl");
return 1;
}
printf("Waiting for usb disconnect\n");
while (!done) {
sleep(1);
}
close(fd);
return 0;
}
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Oliver Neukum <oneukum@suse.com>
Fixes: v2.3.39
Cc: stable@vger.kernel.org
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
In commit 8122de5460 ("dt-bindings: Convert vendor prefixes to
json-schema"), vendor-prefixes.txt has been converted to a DT schema.
Update the checkpatch.pl DT check to extract vendor prefixes from the new
vendor-prefixes.yaml file.
Fixes: 8122de5460 ("dt-bindings: Convert vendor prefixes to json-schema")
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Rob Herring <robh@kernel.org>
ADD HLG EOTF to the list of EOTF transfer functions supported.
Hybrid Log-Gamma (HLG) is a high dynamic range (HDR) standard.
HLG defines a nonlinear transfer function in which the lower
half of the signal values use a gamma curve and the upper half
of the signal values use a logarithmic curve.
v2: Rebase
v3: Fixed a warning message
v4: Addressed Shashank's review comments
v5: Addressed Jonas Karlman's review comment and dropped the i915
tag from header.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Shashank Sharma <shashank.sharma@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1558015817-12025-8-git-send-email-uma.shankar@intel.com
Enable Dynamic Range and Mastering Infoframe for HDR
content, which is defined in CEA 861.3 spec.
The metadata will be computed based on blending
policy in userspace compositors and passed as a connector
property blob to driver. The same will be sent as infoframe
to panel which support HDR.
Added the const version of infoframe for DRM metadata
for HDR.
v2: Rebase and added Ville's POC changes.
v3: No Change
v4: Addressed Shashank's review comments and merged the
patch making drm infoframe function arguments as constant.
v5: Rebase
v6: Fixed checkpatch warnings with --strict option. Addressed
Shashank's review comments and added his RB.
v7: Addressed Brian Starkey's review comments. Merged 2 patches
into one.
v8: Addressed Jonas Karlman review comments.
v9: Addressed Jonas Karlman review comments.
v10: Addressed Ville's review comments.
v11: Added BUILD_BUG_ON and sizeof instead of magic numbers as
per Ville's comments.
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1558015817-12025-5-git-send-email-uma.shankar@intel.com
HDR metadata block is introduced in CEA-861.3 spec.
Parsing the same to get the panel's HDR metadata.
v2: Rebase and added Ville's POC changes to the patch.
v3: No Change
v4: Addressed Shashank's review comments
v5: Addressed Shashank's comment and added his RB.
v6: Addressed Jonas Karlman review comments.
v7: Adressed Ville's review comments and fixed the issue
with length handling.
v8: Put the length check as per the convention followed in
existing code, as suggested by Ville.
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1558015817-12025-4-git-send-email-uma.shankar@intel.com
This patch adds a blob property to get HDR metadata
information from userspace. This will be send as part
of AVI Infoframe to panel.
It also implements get() and set() functions for HDR output
metadata property.The blob data is received from userspace and
saved in connector state, the same is returned as blob in get
property call to userspace.
v2: Rebase and modified the metadata structure elements
as per Ville's POC changes.
v3: No Change
v4: Addressed Shashank's review comments
v5: Rebase.
v6: Addressed Brian Starkey's review comments, defined
new structure with header for dynamic metadata scalability.
Merge get/set property functions for metadata in this patch.
v7: Addressed Jonas Karlman review comments and defined separate
structure for infoframe to better align with CTA 861.G spec. Added
Shashank's RB.
v8: Addressed Ville's review comments. Moved sink metadata structure
out of uapi headers as suggested by Jonas Karlman.
v9: Rebase and addressed Jonas Karlman review comments.
v10: Addressed Ville's review comments, dropped the metdata_changed
state variable as its not needed anymore.
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1558015817-12025-2-git-send-email-uma.shankar@intel.com
The cec device node can be used right after it was created, but that
leaves a race condition where the device was created, but devnode->registered
was still false. So an ioctl() would result in an error.
So set it to true before calling cdev_device_add() and to false again if
cdev_device_add returned an error.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This can be a debug message. Favour dev_dbg() over dprintk() as this is
already used much more than dprintk().
dvb_frontend: dvb_frontend_get_frequency_limits: frequency interval: tuner: 45000000...860000000, frontend: 44250000...867250000
Fixes: 00ecd6bc71 ("media: dvb_frontend: add debug message for frequency intervals")
Cc: <stable@vger.kernel.org> # 5.0
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
All error cases inside the function already report errors via dev_err(),
and dvb_usb_v2_generic_rw also reports all error cases, so there is
no silent code path when an error has occurred.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Errors are already reported by the common code in dvb_usb_v2_generic_io
(which dvbsky_usb_generic_rw is a wrapper of), so there is no reason
report the error again.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
actual_length != wlen is the only error path which does not generate an
error message. Adding an error message here allows to report a more
specific error and to remove the error reporting from the call sites.
Also clean up the error paths - in case of an error, the remaining
code is skipped, and ret is returned. Skip setting ret and return
immediately (no cleanup necessary).
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
MODULE_DEVICE_TABLE(of, <of_match_table> should be called to complete DT
OF mathing mechanism and register it.
Before this patch:
modinfo drivers/media/rc/ir-spi.ko | grep alias
After this patch:
modinfo drivers/media/rc/ir-spi.ko | grep alias
alias: of:N*T*Cir-spi-ledC*
alias: of:N*T*Cir-spi-led
Reported-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Daniel Gomez <dagmcr@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Jakub Kicinski says:
====================
net/tls: fix device surprise removal with offload
This series fixes two issues with device surprise removal.
First we need to take a read lock around resync, otherwise
netdev notifier handler may clear the structures from under
our feet.
Secondly we need to be careful about the interpretation
of device features. Offload has to be properly cleaned
up even if the TLS device features got cleared after
connection state was installed.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
On device surprise removal path (the notifier) we can't
bail just because the features are disabled. They may
have been enabled during the lifetime of the device.
This bug leads to leaking netdev references and
use-after-frees if there are active connections while
device features are cleared.
Fixes: e8f6979981 ("net/tls: Add generic NIC offload infrastructure")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TLS offload drivers shouldn't (and currently don't) block
the TLS offload feature changes based on whether there are
active offloaded connections or not.
This seems to be a good idea, because we want the admin to
be able to disable the TLS offload at any time, and there
is no clean way of disabling it for active connections
(TX side is quite problematic). So if features are cleared
existing connections will stay offloaded until they close,
and new connections will not attempt offload to a given
device.
However, the offload state removal handling is currently
broken if feature flags get cleared while there are
active TLS offloads.
RX side will completely bail from cleanup, even on normal
remove path, leaving device state dangling, potentially
causing issues when the 5-tuple is reused. It will also
fail to release the netdev reference.
Remove the RX-side warning message, in next release cycle
it should be printed when features are disabled, rather
than when connection dies, but for that we need a more
efficient method of finding connection of a given netdev
(a'la BPF offload code).
Fixes: 4799ac81e5 ("tls: Add rx inline crypto offload")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When netdev with active kTLS sockets in unregistered
notifier callback walks the offloaded sockets and
cleans up offload state. RX data may still be processed,
however, and if resync was requested prior to device
removal we would hit a NULL pointer dereference on
ctx->netdev use.
Make sure resync is under the device offload lock
and NULL-check the netdev pointer.
This should be safe, because the pointer is set to
NULL either in the netdev notifier (under said lock)
or when socket is completely dead and no resync can
happen.
The other access to ctx->netdev in tls_validate_xmit_skb()
does not dereference the pointer, it just checks it against
other device pointer, so it should be pretty safe (perhaps
we can add a READ_ONCE/WRITE_ONCE there, if paranoid).
Fixes: 4799ac81e5 ("tls: Add rx inline crypto offload")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski says:
====================
Documentation: tls: add offload documentation
This set adds documentation for TLS offload. It starts
by making the networking documentation a little easier
to navigate by hiding driver docs a little deeper.
It then RSTifys the existing Kernel TLS documentation.
Last but not least TLS offload documentation is added.
This should help vendors navigate the TLS offload, and
help ensure different implementations stay aligned from
user perspective.
v2:
- address Alexei's and Boris'es commands on patch 3.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Describe existing kernel TLS offload (added back in Linux 4.19) -
the mechanism, the expected behavior and the notable corner cases.
This documentation is mostly targeting hardware vendors who want
to implement offload, to ensure consistency between implementations.
v2:
- add emphasis around TLS_SW/TLS_HW/TLS_HW_RECORD;
- remove mentions of ongoing work (Boris);
- split the flow of data in SW vs. HW cases in TX overview
(Boris);
- call out which fields are updated by the device and which
are filled by the stack (Boris);
- move error handling into it's own section (Boris);
- add more words about fallback (Boris);
- note that checksum validation is required (Alexei);
- note that drivers shouldn't pay attention to the TLS
device features.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Dave Watson <davejwatson@fb.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of the device drivers have really long document titles
making the networking table of contents hard to look through.
Place vendor drivers under a submenu.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Dave Watson <davejwatson@fb.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We used a script to indent this code back in 2012, but I guess it got
confused by the ifdefs and added some extra tabs. This patch removes
them.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Doing kmalloc in atomic context is always an issue,
more so for a list that can grow significantly.
Turns out that the driver only uses the duplicated
list of multicast mac addresses to keep track of
what addresses to delete from h/w before committing
the new list from kernel to h/w back again via set_rx_mode,
every time this list gets updated by the kernel.
Given that the h/w knows how to add and delete mac addresses
based on the mac address value alone, __dev_mc_sync should be
the much better choice of kernel API for these operations
avoiding the considerable overhead of maintaining a duplicated
list in the driver.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Tested-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
inet6_set_link_af requires that at least one of IFLA_INET6_TOKEN or
IFLA_INET6_ADDR_GET_MODE is passed. If none of them is passed, it
returns -EINVAL, which may cause do_setlink() to fail in the middle of
processing other commands and give the following warning message:
A link change request failed with some changes committed already.
Interface eth0 may have been left with an inconsistent configuration,
please check.
Check the presence of at least one of them in inet6_validate_link_af to
detect invalid parameters at an early stage, before do_setlink does
anything. Also validate the address generation mode at an early stage.
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds the ability for Netlink to report a socket's UID along with the
other UNIX diagnostic information that is already available. This will
allow diagnostic tools greater insight into which users control which
socket.
To test this, do the following as a non-root user:
unshare -U -r bash
nc -l -U user.socket.$$ &
.. and verify from within that same session that Netlink UNIX socket
diagnostics report the socket's UID as 0. Also verify that Netlink UNIX
socket diagnostics report the socket's UID as the user's UID from an
unprivileged process in a different session. Verify the same from
a root process.
Signed-off-by: Felipe Gasper <felipe@felipegasper.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
