'VAL' should be protected by the brackets.
v2:
* Squash the fix for Documentation/bpf/btf.rst
Fixes: 69b693f0ae ("bpf: btf: Introduce BPF Type Format (BTF)")
Signed-off-by: Gary Lin <glin@suse.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Add fwnode support to the lm3630a driver and optionally allow
configuring the label, default brightness level, and maximum brightness
level. The two outputs can be controlled by bank A and B independently
or bank A can control both outputs.
If the platform data was not configured, then the driver defaults to
enabling both banks. This patch changes the default value to disable
both banks before parsing the firmware node so that just a single bank
can be enabled if desired. There are no in-tree users of this driver.
Driver was tested on a LG Nexus 5 (hammerhead) phone.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Reviewed-by: Dan Murphy <dmurphy@ti.com>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
lm3630a_bank_a_update_status() and lm3630a_bank_b_update_status()
both return the brightness value if the brightness was successfully
updated. Writing to these attributes via sysfs would cause a 'Bad
address' error to be returned. These functions should return 0 on
success, so let's change it to correct that error.
Fixes: 28e64a68a2 ("backlight: lm3630: apply chip revision")
Signed-off-by: Brian Masney <masneyb@onstation.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Support Touchpad MCU as a special of CrOS EC devices. The current
Touchpad MCU is used on Eve Chromebook and used the same protocol as
other CrOS EC devices.
When a MCU has touchpad support (aka EC_FEATURE_TOUCHPAD), it is
instantiated as a special CrOS EC device with device name 'cros_tp'. So
regardless of the probing order between the actual cros_ec and cros_tp,
the userspace and other kernel drivers should not confuse them.
Signed-off-by: Wei-Ning Huang <wnhuang@google.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Support Fingerprint MCU as a special of CrOS EC devices. The current FP
MCU uses the same EC SPI protocol v3 as other CrOS EC devices on a SPI
bus.
When a MCU has fingerprint support (aka EC_FEATURE_FINGERPRINT), it is
instantiated as a special CrOS EC device with device name 'cros_fp'. So
regardless of the probing order between the actual cros_ec and cros_fp,
the userspace and other kernel drivers should not confuse them.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Update the feature enum for the Chromebook Embedded Controller to the
latest version. Some of these enums are still not used in the kernel but
we might be also interested on have these enums up to date. Userspace
can use them to query the features to the EC via the cros-ec character
device.
While here, also fix a typo in one comment in the enum.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Lochnagar is an evaluation and development board for Cirrus
Logic Smart CODEC and Amp devices. It allows the connection of
most Cirrus Logic devices on mini-cards, as well as allowing
connection of various application processor systems to provide a
full evaluation platform. This driver supports the board
controller chip on the Lochnagar board.
Add links to the binding documents for the new sound and hardware
monitor parts of the driver.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Fix the lm3632 dt binding examples as the LCM enable GPIOs
are defined as enable GPIOs per the regulator/lm363x-regulator.txt
bindings document.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Since there are more IOT2040 variants with identical hardware but
different asset tags, the asset tag matching should be adjusted to
support them.
For the board name "SIMATIC IOT2000", currently there are 2 types of
hardware, IOT2020 and IOT2040. Both are identical regarding the
intel_quark_i2c_gpio. In the future there will be no other devices with
the "SIMATIC IOT2000" DMI board name but different hardware. So remove
the asset tag matching from this driver.
Signed-off-by: Su Bao Cheng <baocheng.su@siemens.com>
Reviewed-by: Jan Kiszka <jan.kiszka@siemens.com>
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Mismatch between what is found in the Datasheets for DA9063 and DA9063L
provided by Dialog Semiconductor, and the register names provided in the
MFD registers file. The changes are for the OTP (one-time-programming)
control registers. The two naming errors are OPT instead of OTP, and
COUNT instead of CONT (i.e. control).
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
MODULE_DEVICE_TABLE(of, <of_match_table> should be called to complete DT
OF mathing mechanism and register it.
Before this patch:
modinfo drivers/mfd/tps65912-spi.ko | grep alias
alias: spi:tps65912
After this patch:
modinfo drivers/mfd/tps65912-spi.ko | grep alias
alias: of:N*T*Cti,tps65912C*
alias: of:N*T*Cti,tps65912
alias: spi:tps65912
Reported-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Daniel Gomez <dagmcr@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The AXP803 has a VBUS power input. Its functionality is the same as the
one found in the AXP813. Now that the axp20x_usb_power driver supports
this variant, we can add an mfd cell for it to use it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
When CONFIG_OF is disabled, we get a harmless warning about an
unused variable:
drivers/mfd/sun6i-prcm.c: In function 'sun6i_prcm_probe':
drivers/mfd/sun6i-prcm.c:151:22: error: unused variable 'np' [-Werror=unused-variable]
Remove the variable and open-code the value in the only place
it is used, so it can get left out as well without CONFIG_OF.
Fixes: a05a2e7998 ("mfd: sun6i-prcm: Allow to compile with COMPILE_TEST")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add support in code for the new forms of the host sleep event.
Detects the presence of this version of the command at runtime,
and use whichever form the EC supports. At this time, always
request the default timeout, and only report the failing response
via a WARN_ONCE(). Future versions could accept the sleep parameter
from outside the driver, and return the response information to
usermode or elsewhere.
Signed-off-by: Evan Green <evgreen@chromium.org>
Reviewed-by: Rajat Jain <rajatja@chromium.org>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Acked-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Introduce the command and response structures for the second revision
of the host sleep event. These structures are part of a new EC change
that enables detection of failure to enter S0ix. The EC waits a
kernel-specified timeout (or a default amount of time) for the S0_SLP
pin to change, and wakes the system if that change does not occur in
time.
Signed-off-by: Evan Green <evgreen@chromium.org>
Reviewed-by: Rajat Jain <rajatja@chromium.org>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Acked-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add the cros-usbpd-logger driver for logging event data for the USB PD
charger available in the Embedded Controller on ChromeOS systems. The
logging feature is logically separate functionality from charge manager,
hence is instantiated as a different driver.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Guenetr Roeck <linux@roeck-us.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The AXP223 can be used both using the RSB proprietary bus, or a more
traditional I2C bus. The RSB is a faster bus and provides more features
(like some integrity checks on the messages), so it's usually preferrable
to use it, but since it's proprietary, when we want to use the PMIC in a
multi-master setup, the i2c might make sense as well.
Let's add that possibility.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Formatting of Kconfig files doesn't look so pretty, so let the
Great White Handkerchief come around and clean it up.
Signed-off-by: Enrico Weigelt, metux IT consult <info@metux.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The AXP813 has a VBUS power input. Now that the axp20x_usb_power driver
supports this variant, we can add an mfd cell for it to use it.
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
[wens@csie.org: add commit message]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
I noticed that we can get a -EREMOTEIO errors on at least omap4 duovero:
twl6040 0-004b: Failed to write 2d = 19: -121
And then any following register access will produce errors.
There 2d offset above is register ACCCTL that gets written on twl6040
powerup. With error checking added to the related regcache_sync() call,
the -EREMOTEIO error is reproducable on twl6040 powerup at least
duovero.
To fix the error, we need to wait until twl6040 is accessible after the
powerup. Based on tests on omap4 duovero, we need to wait over 8ms after
powerup before register write will complete without failures. Let's also
make sure we warn about possible errors too.
Note that we have twl6040_patch[] reg_sequence with the ACCCTL register
configuration and regcache_sync() will write the new value to ACCCTL.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Some system control registers need to be clocked, so the registers can
be accessed. Add an optional clock and attach it to regmap.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
STM32 system configuration controller registers needs to be clocked.
Document clock support on stm32-syscon.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Change the layout of the initialisation of structures with one
element to a single line of code. This keeps the coding style
consistent.
Signed-off-by: Stuart Menefy <stuart.menefy@mathembedded.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add MFD cell for LEDs driver to the Intel Cherry Trail Whiskey Cove PMIC
mfd device driver.
Signed-off-by: Yauhen Kharuzhy <jekhor@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
nv50_head_atomic_duplicate_state() makes a copy of nv50_head_atom
struct. This patch adds copying of struct member named "or", which
previously was left uninitialized in the duplicated structure.
Due to this bug, incorrect nhsync and nvsync values were sometimes used.
In my particular case, that lead to a mismatch between the output
resolution of the graphics device (GeForce GT 630 OEM) and the reported
input signal resolution on the display. xrandr reported 1680x1050, but
the display reported 1280x1024. As a result of this mismatch, the output
on the display looked like it was cropped (only part of the output was
actually visible on the display).
git bisect pointed to commit 2ca7fb5c1c ("drm/nouveau/kms/nv50: handle
SetControlOutputResource from head"), which added the member "or" to
nv50_head_atom structure, but forgot to copy it in
nv50_head_atomic_duplicate_state().
Fixes: 2ca7fb5c1c ("drm/nouveau/kms/nv50: handle SetControlOutputResource from head")
Signed-off-by: Peteris Rudzusiks <peteris.rudzusiks@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Where possible, we want the failsafe link configuration (one which won't
hang the OR during modeset because of not enough bandwidth for the mode)
to also be supported by the sink.
This prevents "link rate unsupported by sink" messages when link training
fails.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
