Status of ADMA channel registers is not saved and restored during system
suspend. During active playback if system enters suspend, this results in
wrong state of channel registers during system resume and playback fails
to resume properly. Fix this by saving following channel registers in
runtime suspend and restore during runtime resume.
* ADMA_CH_LOWER_SRC_ADDR
* ADMA_CH_LOWER_TRG_ADDR
* ADMA_CH_FIFO_CTRL
* ADMA_CH_CONFIG
* ADMA_CH_CTRL
* ADMA_CH_CMD
* ADMA_CH_TC
Runtime PM calls will be inovked during system resume path if a playback
or capture needs to be resumed. Hence above changes work fine for system
suspend case.
Fixes: f46b195799 ("dmaengine: tegra-adma: Add support for Tegra210 ADMA")
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
During an audio playback session it is observed that, audio goes off after
few seconds of continuous pause and play. No audio is heard even when the
playback is resumed.
The reason for above is, currently ADMA driver does not handle DMA_PAUSE/
DMA_RESUME and relevant callbacks for dma_device are not implemented. This
patch implements device_pause and device_resume callbacks for the device.
During pause TRANSFER_PAUSE bit of dma channel control register is set and
the same is cleared during resume.
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add Tegra186 specific macro defines and chip_data structure for chip
specific information. New compatibility is added to select relevant
chip details. There is no major change for Tegra194 and hence it can
use the same chip data.
The bits in the BURST_SIZE field of the ADMA CH_CONFIG register are
encoded differently on Tegra186 and Tegra194 compared with Tegra210.
On Tegra210 the bits are encoded as follows ...
1 = WORD_1
2 = WORDS_2
3 = WORDS_4
4 = WORDS_8
5 = WORDS_16
Where as on Tegra186 and Tegra194 the bits are encoded as ...
0 = WORD_1
1 = WORDS_2
2 = WORDS_3
3 = WORDS_4
4 = WORDS_5
...
15 = WORDS_16
Add helper functions for generating the correct burst size.
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Tegra186 Audio DMA controller has new updates from Tegra210 version.
Thus add new compatibility binding string and the same can be used
by Tegra194 as well.
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This is a preparatory patch to add support for Tegra186 and Tegra194 chips.
Following changes are necessary to make driver code generic.
* chip_data structure is enhanced to have chip specific details and
following are the additions to the structure
* Offset addresses for ADMA global and channel registers
* Offset values for Tx and Rx channel selection
* Maximum supported Tx and Rx channels
* Tx and Rx channel request mask
* ADMA channel register space size
* Make use of above chip_data to generalise the driver code
Support for Tegra186 and Tegra194 will be added in subsequent patches of
the series.
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
We switched this code from spin_lock_bh() to vanilla spin_lock() but
there was one stray spin_unlock_bh() that was overlooked. This
patch converts it to spin_unlock() as well.
Fixes: d8570d018f ("dmaengine: at_xdmac: move spin_lock_bh to spin_lock in tasklet")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Fix indentation and remove unneeded space after 'return' keyword. This
fixes checkpatch warning:
WARNING: Statements should start on a tabstop
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In double buffer mode, during residue calculation, the DMA can
automatically switch to the next transfer. Indeed the CT bit that
gives position in the double buffer can has been updated by the
hardware, during calculation.
In this case the SxNDTR register value can not be trusted.
If a transition is detected we consider that the DMA has switched to
the beginning of next sg.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Asking the GPU to busywait on a memory address, perhaps not unexpectedly
in hindsight for a shared system, leads to bus contention that affects
CPU programs trying to concurrently access memory. This can manifest as
a drop in transcode throughput on highly over-saturated workloads.
The only clue offered by perf, is that the bus-cycles (perf stat -e
bus-cycles) jumped by 50% when enabling semaphores. This corresponds
with extra CPU active cycles being attributed to intel_idle's mwait.
This patch introduces a heuristic to try and detect when more than one
client is submitting to the GPU pushing it into an oversaturated state.
As we already keep track of when the semaphores are signaled, we can
inspect their state on submitting the busywait batch and if we planned
to use a semaphore but were too late, conclude that the GPU is
overloaded and not try to use semaphores in future requests. In
practice, this means we optimistically try to use semaphores for the
first frame of a transcode job split over multiple engines, and fail if
there are multiple clients active and continue not to use semaphores for
the subsequent frames in the sequence. Periodically, we try to
optimistically switch semaphores back on whenever the client waits to
catch up with the transcode results.
With 1 client, on Broxton J3455, with the relative fps normalized by %cpu:
x no semaphores
+ drm-tip
* patched
+------------------------------------------------------------------------+
| * |
| *+ |
| **+ |
| **+ x |
| x * +**+ x |
| x x * * +***x xx |
| x x * * *+***x *x |
| x x* + * * *****x *x x |
| + x xx+x* + *** * ********* x * |
| + x xx+x* * *** +** ********* xx * |
| * + ++++* + x*x****+*+* ***+*************+x* * |
|*+ +** *+ + +* + *++****** *xxx**********x***+*****************+*++ *|
| |__________A_____M_____| |
| |_______________A____M_________| |
| |____________A___M________| |
+------------------------------------------------------------------------+
N Min Max Median Avg Stddev
x 120 2.60475 3.50941 3.31123 3.2143953 0.21117399
+ 120 2.3826 3.57077 3.25101 3.1414161 0.28146407
Difference at 95.0% confidence
-0.0729792 +/- 0.0629585
-2.27039% +/- 1.95864%
(Student's t, pooled s = 0.248814)
* 120 2.35536 3.66713 3.2849 3.2059917 0.24618565
No difference proven at 95.0% confidence
With 10 clients over-saturating the pipeline:
x no semaphores
+ drm-tip
* patched
+------------------------------------------------------------------------+
| ++ ** |
| ++ ** |
| ++ ** |
| ++ ** |
| ++ xx *** |
| ++ xx *** |
| ++ xxx*** |
| ++ xxx*** |
| +++ xxx*** |
| +++ xx**** |
| +++ xx**** |
| +++ xx**** |
| +++ xx**** |
| ++++ xx**** |
| +++++ xx**** |
| +++++ x x****** |
| ++++++ xxx******* |
| ++++++ xxx******* |
| ++++++ xxx******* |
| ++++++ xx******** |
| ++++++ xxxx******** |
| ++++++ xxxx******** |
| ++++++++ xxxxx********* |
|+ + + + ++++++++ xxx*xx**********x* *|
| |__A__| |
| |__AM__| |
| |__A_| |
+------------------------------------------------------------------------+
N Min Max Median Avg Stddev
x 120 2.47855 2.8972 2.72376 2.7193402 0.074604933
+ 120 1.17367 1.77459 1.71977 1.6966782 0.085850697
Difference at 95.0% confidence
-1.02266 +/- 0.0203502
-37.607% +/- 0.748352%
(Student's t, pooled s = 0.0804246)
* 120 2.57868 3.00821 2.80142 2.7923878 0.058646477
Difference at 95.0% confidence
0.0730476 +/- 0.0169791
2.68622% +/- 0.624383%
(Student's t, pooled s = 0.0671018)
Indicating that we've recovered the regression from enabling semaphores
on this saturated setup, with a hint towards an overall improvement.
Very similar, but of smaller magnitude, results are observed on both
Skylake(gt2) and Kabylake(gt4). This may be due to the reduced impact of
bus-cycles, where we see a 50% hit on Broxton, it is only 10% on the big
core, in this particular test.
One observation to make here is that for a greedy client trying to
maximise its own throughput, using semaphores is the right choice. It is
only the holistic system-wide view that semaphores of one client
impacts another and reduces the overall throughput where we would choose
to disable semaphores.
The most noticeable negactive impact this has is on the no-op
microbenchmarks, which are also very notable for having no cpu bus load.
In particular, this increases the runtime and energy consumption of
gem_exec_whisper.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Dmitry Rogozhkin <dmitry.v.rogozhkin@intel.com>
Cc: Dmitry Ermilov <dmitry.ermilov@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190504070707.30902-1-chris@chris-wilson.co.uk
e is the counter used to save the location of a dump when an
skb is filled. Once the walk of the table is complete, mr_table_dump
needs to return without resetting that index to 0. Dump of a specific
table is looping because of the reset because there is no way to
indicate the walk of the table is done.
Move the reset to the caller so the dump of each table starts at 0,
but the loop counter is maintained if a dump fills an skb.
Fixes: e1cedae1ba ("ipmr: Refactor mr_rtm_dumproute")
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For all other error cases in queue_userspace_packet() the error is
returned, so it makes sense to do the same for these two error cases.
Reported-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: Eelco Chaudron <echaudro@redhat.com>
Acked-by: Flavio Leitner <fbl@sysclose.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
rtl_write_exgmac_batch is used in only one place, so we can remove it.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michal Kubecek says:
====================
netlink: strict attribute checking follow-up
Three follow-up patches for recent strict netlink validation series.
Patch 1 fixes dump handling for genetlink families which validate and parse
messages themselves (e.g. because they need different policies for diferent
commands).
Patch 2 sets bad_attr in extack in one place where this was omitted.
Patch 3 adds new NL_VALIDATE_NESTED flags for strict validation to enable
checking that NLA_F_NESTED value in received messages matches expectations
and includes this flag in NL_VALIDATE_STRICT. This would change userspace
visible behavior but the previous switching to NL_VALIDATE_STRICT for new
code is still only in net-next at the moment.
v2: change error messages to mention NLA_F_NESTED explicitly
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add new validation flag NL_VALIDATE_NESTED which adds three consistency
checks of NLA_F_NESTED_FLAG:
- the flag is set on attributes with NLA_NESTED{,_ARRAY} policy
- the flag is not set on attributes with other policies except NLA_UNSPEC
- the flag is set on attribute passed to nla_parse_nested()
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
v2: change error messages to mention NLA_F_NESTED explicitly
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The check that attribute type is within 0...maxtype range in
__nla_validate_parse() sets only error message but not bad_attr in extack.
Set also bad_attr to tell userspace which attribute failed validation.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unlike do requests, dump genetlink requests now perform strict validation
by default even if the genetlink family does not set policy and maxtype
because it does validation and parsing on its own (e.g. because it wants to
allow different message format for different commands). While the null
policy will be ignored, maxtype (which would be zero) is still checked so
that any attribute will fail validation.
The solution is to only call __nla_validate() from genl_family_rcv_msg()
if family->maxtype is set.
Fixes: ef6243acb4 ("genetlink: optionally validate strictly/dumps")
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel says:
====================
mlxsw: Firmware version update
This patchset updates mlxsw to use a new firmware version and adds
support for split into two ports on Spectrum-2 based systems.
Patch #1 updates the firmware version to 13.2000.1122
Patch #2 queries new resources from the firmware.
Patch #3 makes use of these resources in order to support split into two
ports on Spectrum-2 based systems. The need for these resources is
explained by Shalom:
When splitting a port, different local ports need to be mapped on different
systems. For example:
SN3700 (local_ports_in_2x=2):
* Without split:
front panel 1 --> local port 1
front panel 2 --> local port 5
* Split to 2:
front panel 1s0 --> local port 1
front panel 1s1 --> local port 3
front panel 2 --> local port 5
SN3800 (local_ports_in_2x=1):
* Without split:
front panel 1 --> local port 1
front panel 2 --> local port 3
* Split to 2:
front panel 1s0 --> local port 1
front panel 1s1 --> local port 2
front panel 2 --> local port 3
The local_ports_in_{1x, 2x} resources provide the offsets from the base
local ports according to which the new local ports can be calculated.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When splitting a port, different local ports need to be mapped on different
systems. For example:
SN3700 (local_ports_in_2x=2):
* Without split:
front panel 1 --> local port 1
front panel 2 --> local port 5
* Split to 2:
front panel 1s0 --> local port 1
front panel 1s1 --> local port 3
front panel 2 --> local port 5
SN3800 (local_ports_in_2x=1):
* Without split:
front panel 1 --> local port 1
front panel 2 --> local port 3
* Split to 2:
front panel 1s0 --> local port 1
front panel 1s1 --> local port 2
front panel 2 --> local port 3
The local_ports_in_{1x, 2x} resources provide the offsets from the base
local ports according to which the new local ports can be calculated.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the number of local ports in 4x changed between SPC and SPC-2,
firmware expose new resources that the driver can query.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new version supports two features that are required by upcoming
changes in the driver:
* Querying of new resources allowing port split into two ports on
Spectrum-2 systems
* Querying of number of gearboxes on supported systems such as SN3800
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TIPC link can temporarily fall into "half-establish" that only one of
the link endpoints is ESTABLISHED and starts to send traffic, PROTOCOL
messages, whereas the other link endpoint is not up (e.g. immediately
when the endpoint receives ACTIVATE_MSG, the network interface goes
down...).
This is a normal situation and will be settled because the link
endpoint will be eventually brought down after the link tolerance time.
However, the situation will become worse when the second link is
established before the first link endpoint goes down,
For example:
1. Both links <1A-2A>, <1B-2B> down
2. Link endpoint 2A up, but 1A still down (e.g. due to network
disturbance, wrong session, etc.)
3. Link <1B-2B> up
4. Link endpoint 2A down (e.g. due to link tolerance timeout)
5. Node B starts failover onto link <1B-2B>
==> Node A does never start link failover.
When the "half-failover" situation happens, two consequences have been
observed:
a) Peer link/node gets stuck in FAILINGOVER state;
b) Traffic or user messages that peer node is trying to failover onto
the second link can be partially or completely dropped by this node.
The consequence a) was actually solved by commit c140eb166d ("tipc:
fix failover problem"), but that commit didn't cover the b). It's due
to the fact that the tunnel link endpoint has never been prepared for a
failover, so the 'l->drop_point' (and the other data...) is not set
correctly. When a TUNNEL_MSG from peer node arrives on the link,
depending on the inner message's seqno and the current 'l->drop_point'
value, the message can be dropped (- treated as a duplicate message) or
processed.
At this early stage, the traffic messages from peer are likely to be
NAME_DISTRIBUTORs, this means some name table entries will be missed on
the node forever!
The commit resolves the issue by starting the FAILOVER process on this
node as well. Another benefit from this solution is that we ensure the
link will not be re-established until the failover ends.
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
I got an interesting report [0] that after resuming from hibernation
the link has 100Mbps instead of 1Gbps. Reason is that another OS has
been used whilst Linux was hibernated. And this OS speeds down the link
due to WoL. Therefore, when resuming, we shouldn't expect that what
the PHY advertises is what it did when hibernating.
Easiest way to do this is removing state PHY_RESUMING. Instead always
go via PHY_UP that configures PHY advertisement.
[0] https://bugzilla.kernel.org/show_bug.cgi?id=202851
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
When probing the phy device we set sym and asym pause in the "supported"
bitmap (unless the PHY tells us otherwise). However we don't know yet
whether the MAC supports pause. Simply copying phy->supported to
phy->advertising will trigger advertising pause, and that's not
what we want. Therefore add phy_advertise_supported() that copies all
modes but doesn't touch the pause bits.
In phy_support_(a)sym_pause we shouldn't set any bits in the supported
bitmap because we may set a bit the PHY intentionally disabled.
Effective pause support should be the AND-combined PHY and MAC pause
capabilities. If the MAC supports everything, then it's only relevant
what the PHY supports. If MAC supports sym pause only, then we have to
clear the asym bit in phydev->supported.
Copy the pause flags only and don't touch the modes, because a driver
may have intentionally removed a mode from phydev->advertising.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make use of the struct_size() helper instead of an open-coded version
in order to avoid any potential type mistakes, in particular in the
context in which this code is being used.
So, replace code of the following form:
sizeof(*s) + s->nkeys*sizeof(struct tc_u32_key)
with:
struct_size(s, keys, s->nkeys)
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Although devlink health report does a nice job on reporting TX
timeout and other NIC errors, unfortunately it requires drivers
to support it but currently only mlx5 has implemented it.
Before other drivers could catch up, it is useful to have a
generic tracepoint to monitor this kind of TX timeout. We have
been suffering TX timeout with different drivers, we plan to
start to monitor it with rasdaemon which just needs a new tracepoint.
Sample output:
ksoftirqd/1-16 [001] ..s2 144.043173: net_dev_xmit_timeout: dev=ens3 driver=e1000 queue=0
Cc: Eran Ben Elisha <eranbe@mellanox.com>
Cc: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit cd9ff4de01 changed the key for IFF_POINTOPOINT devices to
INADDR_ANY but neigh_xmit which is used for MPLS encapsulations was not
updated to use the altered key. The result is that every packet Tx does
a lookup on the gateway address which does not find an entry, a new one
is created only to find the existing one in the table right before the
insert since arp_constructor was updated to reset the primary key. This
is seen in the allocs and destroys counters:
ip -s -4 ntable show | head -10 | grep alloc
which increase for each packet showing the unnecessary overhread.
Fix by having neigh_xmit use __ipv4_neigh_lookup_noref for NEIGH_ARP_TABLE.
Fixes: cd9ff4de01 ("ipv4: Make neigh lookup keys for loopback/point-to-point devices be INADDR_ANY")
Reported-by: Alan Maguire <alan.maguire@oracle.com>
Signed-off-by: David Ahern <dsahern@gmail.com>
Tested-by: Alan Maguire <alan.maguire@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ian and Alan both reported seeing overflows after upgrades to 5.x kernels:
neighbour: arp_cache: neighbor table overflow!
Alan's mpls script helped get to the bottom of this bug. When a new entry
is created the gc_entries counter is bumped in neigh_alloc to check if a
new one is allowed to be created. ___neigh_create then searches for an
existing entry before inserting the just allocated one. If an entry
already exists, the new one is dropped in favor of the existing one. In
this case the cleanup path needs to drop the gc_entries counter. There
is no memory leak, only a counter leak.
Fixes: 58956317c8 ("neighbor: Improve garbage collection")
Reported-by: Ian Kumlien <ian.kumlien@gmail.com>
Reported-by: Alan Maguire <alan.maguire@oracle.com>
Signed-off-by: David Ahern <dsahern@gmail.com>
Tested-by: Alan Maguire <alan.maguire@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Saeed Mahameed says:
====================
mlx5-updates-2019-04-30
mlx5 misc updates:
1) Bodong Wang and Parav Pandit (6):
- Remove unused mlx5_query_nic_vport_vlans
- vport macros refactoring
- Fix vport access in E-Switch
- Use atomic rep state to serialize state change
2) Eli Britstein (2):
- prio tag mode support, added ACLs and replace TC vlan pop with
vlan 0 rewrite when prio tag mode is enabled.
3) Erez Alfasi (2):
- ethtool: Add SFF-8436 and SFF-8636 max EEPROM length definitions
- mlx5e: ethtool, Add support for EEPROM high pages query
4) Masahiro Yamada (1):
- remove meaningless CFLAGS_tracepoint.o
5) Maxim Mikityanskiy (1):
- Put the common XDP code into a function
6) Tariq Toukan (2):
- Turn on HW tunnel offload in all TIRs
7) Vlad Buslov (1):
- Return error when trying to insert existing flower filter
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
100GbE Intel Wired LAN Driver Updates 2019-05-02
This series contains updates to the ice driver only.
Anirudh introduces the framework to store queue specific information in
the VSI queue contexts. This will allow future changes to update the
structure to hold queue specific information.
Akeem adds additional check so that if there is no queue to disable when
attempting to disable a queue, return a configuration error without
acquiring the lock. Fixed an issue with non-trusted VFs being able to
add more than the permitted number of VLANs.
Bruce removes unreachable code and updated the function to return void
since it would never return anything but success.
Brett provides most of the changes in the series, starting with reducing
the scope of the error variable used and improved the debug message if
we fail to configure the receive queue. Updates the driver to use a
macro instead of using the same 'for' loop throughout the driver which
helps with readability. Fixed an issue where users were led to believe
they could set rx-usecs-high value, yet the changes to this value would
not stick because it was not yet implemented to allow changes to this
value, so implement the missing code to change the value. Found we had
unnecessary wait when disabling queues, so remove it. I,proved a
wasteful addition operation in our hot path by adding a member to the
ice_q_vector structure and the necessary changes to use the member which
stores the calculated vector hardware index. Refactored the link event
flow to make it cleaner and more clear.
Maciej updates the array index when stopping transmit rings, so that
process every ring the VSI, not just the rings in a given transmit
class.
Paul adds support for setting 52 byte RSS hash keys.
Md Fahad cleaned up a runtime change to the PFINT_OICR_ENA register,
since the interrupt handlers will handle resetting the bit, if
necessary.
Tony adds a missing PHY type, which was causing warning message about an
unrecognized PHY.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Sameeh Jubran says:
====================
Bug fixes for ENA Ethernet driver
Sameeh Jubran (8):
net: ena: fix swapped parameters when calling
ena_com_indirect_table_fill_entry
net: ena: fix: set freed objects to NULL to avoid failing future
allocations
net: ena: fix: Free napi resources when ena_up() fails
net: ena: fix incorrect test of supported hash function
net: ena: fix return value of ena_com_config_llq_info()
net: ena: improve latency by disabling adaptive interrupt moderation
by default
net: ena: fix ena_com_fill_hash_function() implementation
net: ena: gcc 8: fix compilation warning
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
GCC 8 contains a number of new warnings as well as enhancements to existing
checkers. The warning - Wstringop-truncation - warns for calls to bounded
string manipulation functions such as strncat, strncpy, and stpncpy that
may either truncate the copied string or leave the destination unchanged.
In our case the destination string length (32 bytes) is much shorter than
the source string (64 bytes) which causes this warning to show up. In
general the destination has to be at least a byte larger than the length
of the source string with strncpy for this warning not to showup.
This can be easily fixed by using strlcpy instead which already does the
truncation to the string. Documentation for this function can be
found here:
https://elixir.bootlin.com/linux/latest/source/lib/string.c#L141
Fixes: 1738cd3ed3 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adaptive interrupt moderation was erroneously enabled by default
in the driver.
In case the device supports adaptive interrupt moderation it will
be automatically used, which may potentially increase latency.
The adaptive moderation can be enabled from ethtool command in
case the feature is supported by the device.
Fixes: 1738cd3ed3 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Guy Tzalik <gtzalik@amazon.com>
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ena_com_config_llq_info() returns 0 even if ena_com_set_llq() fails.
Return the failure code of ena_com_set_llq() in case it fails.
fixes: 689b2bdaaa ("net: ena: add functions for handling Low Latency Queues in ena_com")
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ena_com_set_hash_function() tests if a hash function is supported
by the device before setting it.
The test returns the opposite result than needed.
Reverse the condition to return the correct value.
Also use the BIT macro instead of inline shift.
Fixes: 1738cd3ed3 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ena_up() calls ena_init_napi() but does not call ena_del_napi() in
case of failure. This causes a segmentation fault upon rmmod when
netif_napi_del() is called. Fix this bug by calling ena_del_napi()
before returning error from ena_up().
Fixes: 1738cd3ed3 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In some cases when a queue related allocation fails, successful past
allocations are freed but the pointer that pointed to them is not
set to NULL. This is a problem for 2 reasons:
1. This is generally a bad practice since this pointer might be
accidentally accessed in the future.
2. Future allocations using the same pointer check if the pointer
is NULL and fail if it is not.
Fixed this by setting such pointers to NULL in the allocation of
queue related objects.
Also refactored the code of ena_setup_tx_resources() to goto-style
error handling to avoid code duplication of resource freeing.
Fixes: 1738cd3ed3 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
second parameter should be the index of the table rather than the value.
Fixes: 1738cd3ed3 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Saeed Bshara <saeedb@amazon.com>
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make use of the struct_size() helper instead of an open-coded version
in order to avoid any potential type mistakes, in particular in the
context in which this code is being used.
So, replace code of the following form:
sizeof(*tx_msg) + le16_to_cpu(tx_msg->num_pls) * sizeof(tx_msg->pld[0]);
with:
struct_size(tx_msg, pld, le16_to_cpu(tx_msg->num_pls));
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jian Shen says:
====================
net: hns3: enhance capabilities for fibre port
This patchset enhances more capabilities for fibre port,
include multipe media type identification, autoneg,
change port speed and FEC encoding.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for FEC encoding control, user can change
FEC mode by command ethtool --set-fec, and get FEC mode by command
ethtool --show-fec. The fec capability is changed follow the port
speed. If autoneg on, the user configure fec mode will be overwritten
by autoneg result.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously, our driver only supports phydev to autoneg or change
port speed. This patch adds support for fibre port, driver gets
media speed capability and autoneg capability from firmware. If
the media supports multiple speeds, user can change port speed
with command "ethtool -s <devname> speed xxxx autoneg off duplex
full". If autoneg on, the user configuration may be overwritten
by the autoneg result.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously, we can only identify copper and fiber type, the
supported link modes of port information are always showing
SR type. This patch adds support for multiple media types,
include SR, LR CR, KR. Driver needs to query the media type
from firmware periodicly, and updates the port information.
The new port information looks like this:
Settings for eth0:
Supported ports: [ FIBRE ]
Supported link modes: 25000baseCR/Full
25000baseSR/Full
1000baseX/Full
10000baseCR/Full
10000baseSR/Full
10000baseLR/Full
Supported pause frame use: Symmetric
Supports auto-negotiation: No
Supported FEC modes: None BaseR
Advertised link modes: Not reported
Advertised pause frame use: No
Advertised auto-negotiation: No
Advertised FEC modes: Not reported
Speed: 10000Mb/s
Duplex: Full
Port: FIBRE
PHYAD: 0
Transceiver: internal
Auto-negotiation: off
Current message level: 0x00000036 (54)
probe link ifdown ifup
Link detected: yes
In order to be compatible with old firmware which only support
sfp speed, we remained using the same query command, and kept
the former logic.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ipheth_carrier_set() is called from two locations. In
ipheth_carrier_check_work(), its parameter 'dev' is set with
container_of(work, ...) and can not be NULL. In ipheth_open(),
dev is extracted from netdev_priv(net) and dereferenced before
the call to ipheth_carrier_set(). The NULL pointer check of dev
in ipheth_carrier_set() is therefore unnecessary and can be removed.
Cc: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow an interrupt number to be passed in the platform data. The
driver will then use it if not zero, otherwise it will poll for
interrupts.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn says:
====================
mv88e6xxx: Disable ports to save power
Save some power by disabling ports. The first patch fully disables a
port when it is runtime disabled. The second disables any ports which
are not used at all.
Depending on configuration strapping, this can lower the temperature
of an idle switch a few degrees.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
If the NO_CPU strap is set, the switch starts in 'dumb hub' mode, with
all ports enable. Ports which are then actively used are reconfigured
as required when the driver starts. However unused ports are left
alone. Change this to disable them, and turn off any SERDES
interface. This could save some power and so reduce the temperature a
bit.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
