When requested to disable a port, set the port STP state to disabled.
This fully disables the port and should save some power.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the ring buffer is almost full due to RX completion messages, a
TX packet may reach the "low watermark" and cause the queue stopped.
If the TX completion arrives earlier than queue stopping, the wakeup
may be missed.
This patch moves the check for the last pending packet to cover both
EAGAIN and success cases, so the queue will be reliably waked up when
necessary.
Reported-and-tested-by: Stephan Klein <stephan.klein@wegfinder.at>
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2019-05-03
This series contains updates to the i40e driver only.
Carolyn changes the driver behavior to now disable the VF after one MDD
event instead of allowing a couple of MDD events before doing the reset.
Aleksandr changes the driver to only report an error when a VF tries to
remove VLAN when a port VLAN is configured, unless it is VLAN 0. Also
extends the LLDP support to be able to keep the current LLDP state
persistent across a power cycle.
Maciej fixes the checksum calculation due to firmware changes, which
requires the driver to perform a double shadow RAM dump in some cases.
Adam adds advertising support for 40GBase_LR4, 40GBase_CR4 and fibre in
the driver.
Jake cleans up a check that is not needed and was producing a warning in
GCC 8.
Harshitha fixes a misleading message by ensuring that a success message
is only printed on the host side when the promiscuous mode change has
been successful.
Stefan Assmann adds the vendor id and device id to the dmesg log entry
during probe to help with bug reports when lspci output may not be
available.
Alice and Piotr add recovery mode support in the i40e driver, which is
needed for migrating from a structured to a flat firmware image.
v2: Removed patch 1 "i40e: replace switch-statement to speed-up
retpoline-enabled builds" from the series since it is no longer
needed. Also updated the last patch in the series that introduces
recovery mode support, to include a more detailed patch description
and removed code not intended for the upstream kernel.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull KVM fixes from Paolo Bonzini:
- PPC and ARM bugfixes from submaintainers
- Fix old Windows versions on AMD (recent regression)
- Fix old Linux versions on processors without EPT
- Fixes for LAPIC timer optimizations
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (21 commits)
KVM: nVMX: Fix size checks in vmx_set_nested_state
KVM: selftests: make hyperv_cpuid test pass on AMD
KVM: lapic: Check for in-kernel LAPIC before deferencing apic pointer
KVM: fix KVM_CLEAR_DIRTY_LOG for memory slots of unaligned size
x86/kvm/mmu: reset MMU context when 32-bit guest switches PAE
KVM: x86: Whitelist port 0x7e for pre-incrementing %rip
Documentation: kvm: fix dirty log ioctl arch lists
KVM: VMX: Move RSB stuffing to before the first RET after VM-Exit
KVM: arm/arm64: Don't emulate virtual timers on userspace ioctls
kvm: arm: Skip stage2 huge mappings for unaligned ipa backed by THP
KVM: arm/arm64: Ensure vcpu target is unset on reset failure
KVM: lapic: Convert guest TSC to host time domain if necessary
KVM: lapic: Allow user to disable adaptive tuning of timer advancement
KVM: lapic: Track lapic timer advance per vCPU
KVM: lapic: Disable timer advancement if adaptive tuning goes haywire
x86: kvm: hyper-v: deal with buggy TLB flush requests from WS2012
KVM: x86: Consider LAPIC TSC-Deadline timer expired if deadline too short
KVM: PPC: Book3S: Protect memslots while validating user address
KVM: PPC: Book3S HV: Perserve PSSCR FAKE_SUSPEND bit on guest exit
KVM: arm/arm64: vgic-v3: Retire pending interrupts on disabling LPIs
...
This patch updates the parisc huge TLB page support to use per-pagetable spinlocks.
This patch requires Mikulas' per-pagetable spinlock patch and the revised TLB
serialization patch from Helge and myself. With Mikulas' patch, we need to use
the per-pagetable spinlock for page table updates. The TLB lock is only used
to serialize TLB flushes on machines with the Merced bus.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Signed-off-by: Helge Deller <deller@gmx.de>
PA-RISC uses a global spinlock to protect pagetable updates in the TLB
fault handlers. When multiple cores are taking TLB faults simultaneously,
the cache line containing the spinlock becomes a bottleneck.
This patch embeds the spinlock in the top level page directory, so that
every process has its own lock. It improves performance by 30% when
doing parallel compilations.
At least on the N class systems, only one PxTLB inter processor
broadcast can be active at any one time on the Merced bus. If a Merced
bus is found, this patch serializes the TLB flushes with the
pa_tlb_flush_lock spinlock.
v1: Initial patch by Mikulas
v2: Added Merced detection by Helge
v3: Revised TLB serialization by Dave & Helge
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Signed-off-by: Helge Deller <deller@gmx.de>
When making the text sections writeable with set_kernel_text_rw(1),
include all text sections including those in the __init section.
Otherwise functions marked with __meminit will stay read-only.
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: <stable@vger.kernel.org> # 4.20+
The pdtlb and pitlb instructions are strongly ordered. The asms invoking
these instructions should be compiler memory barriers to ensure the
compiler doesn't reorder memory operations around these instructions.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
CC: stable@vger.kernel.org # v4.20+
Fixes: 3847dab774 ("parisc: Add alternative coding infrastructure")
Signed-off-by: Helge Deller <deller@gmx.de>
There are only a couple of instructions that can function as a memory
barrier on parisc. Currently, we use the sync instruction as a memory
barrier when releasing a spinlock. However, the ldcw instruction is a
better barrier when we have a handy memory location since it operates in
the cache on coherent machines.
This patch updates the spinlock release code to use ldcw. I also
changed the "stw,ma" instructions to "stw" instructions as it is not an
adequate barrier.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Signed-off-by: Helge Deller <deller@gmx.de>
TLB operations only need to be serialized on machines with the Merced
(Stretch) bus. The only machines in this category are L and N class, and
they require a 64-bit PA 2.0 kernel. On these machines, we use local TLB
purges in the tmpalias routines.
We don't need to serialize TLB purges on all other machines. Thus, the
lock/unlock code can be removed when CONFIG_PA20 is not defined.
Further, when CONFIG_PA20 is not defined, alternative patching converts
the TLB purges to local purges when PA 2.0 hardware has been detected.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Tested-By: Sven Schnelle <svens@stackframe.org>
Signed-off-by: Helge Deller <deller@gmx.de>
The commit 1c30844d2d ("mm: reclaim small amounts of memory when an
external fragmentation event occurs") breaks memory management on a
parisc c8000 workstation with this memory layout:
0) Start 0x0000000000000000 End 0x000000003fffffff Size 1024 MB
1) Start 0x0000000100000000 End 0x00000001bfdfffff Size 3070 MB
2) Start 0x0000004040000000 End 0x00000040ffffffff Size 3072 MB
With the patch 1c30844d2d, the kernel will incorrectly reclaim the
first zone when it fills up, ignoring the fact that there are two
completely free zones. Basiscally, it limits cache size to 1GiB.
The parisc kernel is currently using the DISCONTIGMEM implementation,
but isn't NUMA. Avoid this issue or strange work-arounds by switching to
the more commonly used SPARSEMEM implementation.
Reported-by: Mikulas Patocka <mpatocka@redhat.com>
Fixes: 1c30844d2d ("mm: reclaim small amounts of memory when an external fragmentation event occurs")
Signed-off-by: Helge Deller <deller@gmx.de>
The idle task might have been allocated above 4GB. With the current code
we cannot access that memory because the CPU is still running in narrow
mode.
This was found on a J5000 machine and the patch is required to enable
SPARSEMEM on that machine.
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Signed-off-by: Helge Deller <deller@gmx.de>
Update lists to reflect that we have now KGDB and kretprobes
support.
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Signed-off-by: Helge Deller <deller@gmx.de>
It's not used by patch_map()/patch_unmap(), so lets remove
it.
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Signed-off-by: Helge Deller <deller@gmx.de>
Now that kprobes and kretprobes are implemented, update the list in
Documentation to reflect that.
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Signed-off-by: Helge Deller <deller@gmx.de>
Implement kretprobes on parisc, parts stolen from powerpc.
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Signed-off-by: Helge Deller <deller@gmx.de>
Even a 32-bit kernel requires at least 27 MB to decompress itself, so
halt the system with a message if the system has less memory than 32 MB.
Signed-off-by: Helge Deller <deller@gmx.de>
This patch add KGDB support to PA-RISC. It also implements
single-stepping utilizing the recovery counter.
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Signed-off-by: Helge Deller <deller@gmx.de>
Instead of re-mapping the whole kernel text with RWX rights
add a patch_text() which can be used to replace instructions
in the kernel .text section. Based on the ARM implementation.
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Signed-off-by: Helge Deller <deller@gmx.de>
These functions will be used for adding code patching
functions later.
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Signed-off-by: Helge Deller <deller@gmx.de>
Do not offset mmap base address because of stack randomization if
current task does not want randomization.
Signed-off-by: Alexandre Ghiti <alex@ghiti.fr>
Signed-off-by: Helge Deller <deller@gmx.de>
This patch introduces "recovery mode" to the i40e driver. It is
part of a new Any2Any idea of upgrading the firmware. In this
approach, it is required for the driver to have support for
"transition firmware", that is used for migrating from structured
to flat firmware image. In this new, very basic mode, i40e driver
must be able to handle particular IOCTL calls from the NVM Update
Tool and run a small set of AQ commands.
These additional AQ commands are part of the interface used by
the NVMUpdate tool. The NVMUpdate tool contains all of the
necessary logic to reference these new AQ commands. The end user
experience remains the same, they are using the NVMUpdate tool to
update the NVM contents.
Signed-off-by: Alice Michael <alice.michael@intel.com>
Signed-off-by: Piotr Marczak <piotr.marczak@intel.com>
Tested-by: Don Buchholz <donald.buchholz@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Printing each devices PCI vendor and device ID has the advantage of
easily revealing what hardware we're dealing with exactly. It's no
longer necessary to match the PCI bus information to the lspci output.
Helps with bug reports where no lspci output is available.
Output before
i40e 0000:08:00.0: fw 6.1.49420 api 1.7 nvm 6.80 0x80003c64 1.2007.0
and after
i40e 0000:08:00.0: fw 6.1.49420 api 1.7 nvm 6.80 0x80003c64 1.2007.0 [8086:1572] [8086:0004]
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A refactor of the i40e_vc_config_promiscuous_mode_msg function moved
the check for un-trusted VF into another function. We have to lie to
an un-trusted VF that its request to set promiscuous mode is
successful even when it is not because we don't want the VF to find
out its trust status this way. With the refactor, we were running into
a case where even though we were not setting promiscuous mode for an
un-trusted VF, we still printed a misleading message that it was
successful.
This patch fixes that by ensuring that a success message is printed
on the host side only when the promiscuous mode change has been
successful.
Signed-off-by: Harshitha Ramamurthy <harshitha.ramamurthy@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The function i40e_validate_cloud_filter checks that the destination and
source port numbers are valid by attempting to ensure that the number is
non-zero and no larger than 0xFFFF. However, the types for the dst_port
and src_port variable are __be16 which by definition cannot be larger
than 0xFFFF
Since these values cannot be larger than 2 bytes, the check to see if
they exceed 0xFFFF is meaningless.
One might consider these checks as some sort of defensive coding, in
case the type was later changed. However, these checks also byte-swap
the value before comparison using be16_to_cpu, which will truncate the
values to 16bits anyways. Additionally, changing the type would require
updating the opcodes to support new data layout of these virtchnl
commands.
Remove the check to silence the -Wtype-limits warning that was added to
GCC 8.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This code implements driver code changes necessary for LLDP
Agent support. Modified i40e_aq_start_lldp() and
i40e_aq_stop_lldp() adding false parameter whether LLDP state
should be persistent across power cycles.
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Due to changes in FW the SW is required to perform double SR dump in
some cases.
Implementation adds two new steps to update nvm checksum function:
* recalculate checksum and check if checksum in NVM is correct
* if checksum in NVM is not correct then update it again
Signed-off-by: Maciej Paczkowski <maciej.paczkowski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
VF's attempt to delete vlan 0 when a port vlan is configured is harmless
in this case pf driver just does nothing. If vf will try to remove
other vlans when a port vlan is configured it will still produce error
as before.
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
TX MDD events reported on the PF are the result of the
PF misconfiguring a descriptor and not because of "bad actions"
by anything else. No need to reset now because if it
results in a Tx hang, the Tx hang check will take care of it.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch changes the driver behavior when detecting a VF MDD event.
It now disables the VF after one event, which indicates a hw detected
problem in the VF. Before this change, the PF would allow a couple of
events before doing the reset.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The TMP75B has a different control register, supports 12-bit
resolution and the default conversion rate is 37 Hz.
Signed-off-by: Iker Perez del Palomar Sustatxa <iker.perez@codethink.co.uk>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
