[ Upstream commit 76aaf8a967 ]
When usb_clear_halt() fails, dvb->bulk_urb->transfer_buffer
and dvb->bulk_urb should be freed just like when
usb_submit_urb() fails.
Fixes: 3169c9b26f ("V4L/DVB (12788): tm6000: Add initial DVB-T support")
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 15ccc39b3a ]
The main problem with this error handling was that it didn't clean up if
i2c_add_numbered_adapter() failed. This code is pretty old, and doesn't
match with today's checkpatch.pl standards so I took the opportunity to
tidy it up a bit. I changed the NULL comparison, and removed the
WARNING message if kzalloc() fails and updated the label names.
Fixes: 1b082ccf59 ("gma500: Add Oaktrail support")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/X8ikkAqZfnDO2lu6@mwanda
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4773acf3d4 ]
The documentation for the PHY update [1] states:
Loop 4 times with index i
If PHY Revision >= 3
Copy table[i] to coef[i]
Otherwise
Set coef[i] to 0
the copy of the table to coef is currently implemented the wrong way
around, table is being updated from uninitialized values in coeff.
Fix this by swapping the assignment around.
[1] https://bcm-v4.sipsolutions.net/802.11/PHY/N/RestoreCal/
Fixes: 2f258b74d1 ("b43: N-PHY: implement restoring general configuration")
Addresses-Coverity: ("Uninitialized scalar variable")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a3daf3d391 ]
In case of a common event for rx and tx queue the event should be
regarded to be spurious if no rx and no tx requests are pending.
Unfortunately the condition for testing that is wrong causing to
decide a event being spurious if no rx OR no tx requests are
pending.
Fix that plus using local variables for rx/tx pending indicators in
order to split function calls and if condition.
Fixes: 23025393db ("xen/netback: use lateeoi irq binding")
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Reviewed-by: Paul Durrant <paul@xen.org>
Reviewed-by: Wei Liu <wl@xen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 132e0b65dc ]
A TX queue can potentially immediately timeout after it is stopped
and the last TX timestamp on that queue was more than 5 seconds ago with
carrier still up. Prevent these intermittent false TX timeouts
by bringing down carrier first before calling netif_tx_disable().
Fixes: c0c050c58d ("bnxt_en: New Broadcom ethernet driver.")
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7f9942c61f ]
Building with the clang integrated assembler produces a couple of
errors for the s3c24xx fiq support:
arch/arm/mach-s3c/irq-s3c24xx-fiq.S:52:2: error: instruction 'subne' can not set flags, but 's' suffix specified
subnes pc, lr, #4 @@ return, still have work to do
arch/arm/mach-s3c/irq-s3c24xx-fiq.S:64:1: error: invalid symbol redefinition
s3c24xx_spi_fiq_txrx:
There are apparently two problems: one with extraneous or duplicate
labels, and one with old-style opcode mnemonics. Stefan Agner has
previously fixed other problems like this, but missed this particular
file.
Fixes: bec0806cfe ("spi_s3c24xx: add FIQ pseudo-DMA support")
Cc: Stefan Agner <stefan@agner.ch>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Link: https://lore.kernel.org/r/20210204162416.3030114-1-arnd@kernel.org
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1a9e38cabd ]
With some USB network adapters, such as DM96xx, the following message
is seen for each maximum size receive packet.
dwc2 ff540000.usb: dwc2_update_urb_state(): trimming xfer length
This happens because the packet size requested by the driver is 1522
bytes, wMaxPacketSize is 64, the dwc2 driver configures the chip to
receive 24*64 = 1536 bytes, and the chip does indeed send more than
1522 bytes of data. Since the event does not indicate an error condition,
the message is just noise. Demote it to debug level.
Fixes: 7359d482eb ("staging: HCD files for the DWC2 driver")
Tested-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Link: https://lore.kernel.org/r/20210113112052.17063-4-nsaenzjulienne@suse.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f74b68c61c ]
In some situations, the following error messages are reported.
dwc2 ff540000.usb: dwc2_hc_chhltd_intr_dma: Channel 1 - ChHltd set, but reason is unknown
dwc2 ff540000.usb: hcint 0x00000002, intsts 0x04000021
This is sometimes followed by:
dwc2 ff540000.usb: dwc2_update_urb_state_abn(): trimming xfer length
and then:
WARNING: CPU: 0 PID: 0 at kernel/v4.19/drivers/usb/dwc2/hcd.c:2913
dwc2_assign_and_init_hc+0x98c/0x990
The warning suggests that an odd buffer address is to be used for DMA.
After an error is observed, the receive buffer may be full
(urb->actual_length >= urb->length). However, the urb is still left in
the queue unless three errors were observed in a row. When it is queued
again, the dwc2 hcd code translates this into a 1-block transfer.
If urb->actual_length (ie the total expected receive length) is not
DMA-aligned, the buffer pointer programmed into the chip will be
unaligned. This results in the observed warning.
To solve the problem, abort input transactions after an error with
unknown cause if the entire packet was already received. This may be
a bit drastic, but we don't really know why the transfer was aborted
even though the entire packet was received. Aborting the transfer in
this situation is less risky than accepting a potentially corrupted
packet.
With this patch in place, the 'ChHltd set' and 'trimming xfer length'
messages are still observed, but there are no more transfer attempts
with odd buffer addresses.
Fixes: 151d0cbdbe ("usb: dwc2: make the scheduler handle excessive NAKs better")
Cc: Boris ARZUR <boris@konbu.org>
Cc: Douglas Anderson <dianders@chromium.org>
Tested-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Link: https://lore.kernel.org/r/20210113112052.17063-3-nsaenzjulienne@suse.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 415fa1c730 ]
The DWC2 documentation states that transfers with zero data length should
set the number of packets to 1 and the transfer length to 0. This is not
currently the case for inbound transfers: the transfer length is set to
the maximum packet length. This can have adverse effects if the chip
actually does transfer data as it is programmed to do. Follow chip
documentation and keep the transfer length set to 0 in that situation.
Fixes: 56f5b1cff2 ("staging: Core files for the DWC2 driver")
Tested-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Link: https://lore.kernel.org/r/20210113112052.17063-2-nsaenzjulienne@suse.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 2643e6e902 upstream.
TSAUXC.DisableSystime is never set, so SYSTIM runs into a SYS WRAP
every 1100 secs on 80580/i350/i354 (40 bit SYSTIM) and every 35000
secs on 80576 (45 bit SYSTIM).
This wrap event sets the TSICR.SysWrap bit unconditionally.
However, checking TSIM at interrupt time shows that this event does not
actually cause the interrupt. Rather, it's just bycatch while the
actual interrupt is caused by, for instance, TSICR.TXTS.
The conclusion is that the SYS WRAP is actually expected, so the
"unexpected SYS WRAP" message is entirely bogus and just helps to
confuse users. Drop it.
Signed-off-by: Corinna Vinschen <vinschen@redhat.com>
Acked-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Punit Agrawal <punit1.agrawal@toshiba.co.jp>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ed9be64eef upstream.
The HID subsystem allows an "HID report field" to have a different
number of "values" and "usages" when it is allocated. When a field
struct is created, the size of the usage array is guaranteed to be at
least as large as the values array, but it may be larger. This leads to
a potential out-of-bounds write in
__hidinput_change_resolution_multipliers() and an out-of-bounds read in
hidinput_count_leds().
To fix this, let's make sure that both the usage and value arrays are
the same size.
Cc: stable@vger.kernel.org
Signed-off-by: Will McVicker <willmcvicker@google.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 871997bc9e upstream.
The function uses a goto-based loop, which may lead to an earlier error
getting discarded by a later iteration. Exit this ad-hoc loop when an
error was encountered.
The out-of-memory error path additionally fails to fill a structure
field looked at by xen_blkbk_unmap_prepare() before inspecting the
handle which does get properly set (to BLKBACK_INVALID_HANDLE).
Since the earlier exiting from the ad-hoc loop requires the same field
filling (invalidation) as that on the out-of-memory path, fold both
paths. While doing so, drop the pr_alert(), as extra log messages aren't
going to help the situation (the kernel will log oom conditions already
anyway).
This is XSA-365.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Julien Grall <julien@xen.org>
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7c77474b2d upstream.
In particular -ENOMEM may come back here, from set_foreign_p2m_mapping().
Don't make problems worse, the more that handling elsewhere (together
with map's status fields now indicating whether a mapping wasn't even
attempted, and hence has to be considered failed) doesn't require this
odd way of dealing with errors.
This is part of XSA-362.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Cc: stable@vger.kernel.org
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3194a1746e upstream.
In particular -ENOMEM may come back here, from set_foreign_p2m_mapping().
Don't make problems worse, the more that handling elsewhere (together
with map's status fields now indicating whether a mapping wasn't even
attempted, and hence has to be considered failed) doesn't require this
odd way of dealing with errors.
This is part of XSA-362.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Cc: stable@vger.kernel.org
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5a264285ed upstream.
In particular -ENOMEM may come back here, from set_foreign_p2m_mapping().
Don't make problems worse, the more that handling elsewhere (together
with map's status fields now indicating whether a mapping wasn't even
attempted, and hence has to be considered failed) doesn't require this
odd way of dealing with errors.
This is part of XSA-362.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Cc: stable@vger.kernel.org
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ebee0eab08 upstream.
Failure of the kernel part of the mapping operation should also be
indicated as an error to the caller, or else it may assume the
respective kernel VA is okay to access.
Furthermore gnttab_map_refs() failing still requires recording
successfully mapped handles, so they can be unmapped subsequently. This
in turn requires there to be a way to tell full hypercall failure from
partial success - preset map_op status fields such that they won't
"happen" to look as if the operation succeeded.
Also again use GNTST_okay instead of implying its value (zero).
This is part of XSA-361.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Cc: stable@vger.kernel.org
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dbe5283605 upstream.
We may not skip setting the field in the unmap structure when
GNTMAP_device_map is in use - such an unmap would fail to release the
respective resources (a page ref in the hypervisor). Otoh the field
doesn't need setting at all when GNTMAP_device_map is not in use.
To record the value for unmapping, we also better don't use our local
p2m: In particular after a subsequent change it may not have got updated
for all the batch elements. Instead it can simply be taken from the
respective map's results.
We can additionally avoid playing this game altogether for the kernel
part of the mappings in (x86) PV mode.
This is part of XSA-361.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Cc: stable@vger.kernel.org
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fca3f13810 upstream
Originally the procedure of the ULPI transaction finish detection has been
developed as a simple busy-loop with just decrementing counter and no
delays. It's wrong since on different systems the loop will take a
different time to complete. So if the system bus and CPU are fast enough
to overtake the ULPI bus and the companion PHY reaction, then we'll get to
take a false timeout error. Fix this by converting the busy-loop procedure
to take the standard bus speed, address value and the registers access
mode into account for the busy-loop delay calculation.
Here is the way the fix works. It's known that the ULPI bus is clocked
with 60MHz signal. In accordance with [1] the ULPI bus protocol is created
so to spend 5 and 6 clock periods for immediate register write and read
operations respectively, and 6 and 7 clock periods - for the extended
register writes and reads. Based on that we can easily pre-calculate the
time which will be needed for the controller to perform a requested IO
operation. Note we'll still preserve the attempts counter in case if the
DWC USB3 controller has got some internals delays.
[1] UTMI+ Low Pin Interface (ULPI) Specification, Revision 1.1,
October 20, 2004, pp. 30 - 36.
Fixes: 88bc9d194f ("usb: dwc3: add ULPI interface support")
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20201210085008.13264-3-Sergey.Semin@baikalelectronics.ru
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[sudip: adjust context]
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e013f455d9 upstream
The following mem abort is observed when the mba firmware size exceeds
the allocated mba region. MBA firmware size is restricted to a maximum
size of 1M and remaining memory region is used by modem debug policy
firmware when available. Hence verify whether the MBA firmware size lies
within the allocated memory region and is not greater than 1M before
loading.
Err Logs:
Unable to handle kernel paging request at virtual address
Mem abort info:
...
Call trace:
__memcpy+0x110/0x180
rproc_start+0x40/0x218
rproc_boot+0x5b4/0x608
state_store+0x54/0xf8
dev_attr_store+0x44/0x60
sysfs_kf_write+0x58/0x80
kernfs_fop_write+0x140/0x230
vfs_write+0xc4/0x208
ksys_write+0x74/0xf8
__arm64_sys_write+0x24/0x30
...
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Fixes: 051fb70fd4 ("remoteproc: qcom: Driver for the self-authenticating Hexagon v5")
Cc: stable@vger.kernel.org
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Link: https://lore.kernel.org/r/20200722201047.12975-2-sibis@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
[sudip: manual backport to old file path]
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 29b3283972 upstream.
When an Intel IOMMU is virtualized, and a physical device is
passed-through to the VM, changes of the virtual IOMMU need to be
propagated to the physical IOMMU. The hypervisor therefore needs to
monitor PTE mappings in the IOMMU page-tables. Intel specifications
provide "caching-mode" capability that a virtual IOMMU uses to report
that the IOMMU is virtualized and a TLB flush is needed after mapping to
allow the hypervisor to propagate virtual IOMMU mappings to the physical
IOMMU. To the best of my knowledge no real physical IOMMU reports
"caching-mode" as turned on.
Synchronizing the virtual and the physical IOMMU tables is expensive if
the hypervisor is unaware which PTEs have changed, as the hypervisor is
required to walk all the virtualized tables and look for changes.
Consequently, domain flushes are much more expensive than page-specific
flushes on virtualized IOMMUs with passthrough devices. The kernel
therefore exploited the "caching-mode" indication to avoid domain
flushing and use page-specific flushing in virtualized environments. See
commit 78d5f0f500 ("intel-iommu: Avoid global flushes with caching
mode.")
This behavior changed after commit 13cf017446 ("iommu/vt-d: Make use
of iova deferred flushing"). Now, when batched TLB flushing is used (the
default), full TLB domain flushes are performed frequently, requiring
the hypervisor to perform expensive synchronization between the virtual
TLB and the physical one.
Getting batched TLB flushes to use page-specific invalidations again in
such circumstances is not easy, since the TLB invalidation scheme
assumes that "full" domain TLB flushes are performed for scalability.
Disable batched TLB flushes when caching-mode is on, as the performance
benefit from using batched TLB invalidations is likely to be much
smaller than the overhead of the virtual-to-physical IOMMU page-tables
synchronization.
Fixes: 13cf017446 ("iommu/vt-d: Make use of iova deferred flushing")
Signed-off-by: Nadav Amit <namit@vmware.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Lu Baolu <baolu.lu@linux.intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Will Deacon <will@kernel.org>
Cc: stable@vger.kernel.org
Acked-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20210127175317.1600473-1-namit@vmware.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Nadav Amit <namit@vmware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 81b704d3e4 upstream.
Calling acpi_thermal_check() from acpi_thermal_notify() directly
is problematic if _TMP triggers Notify () on the thermal zone for
which it has been evaluated (which happens on some systems), because
it causes a new acpi_thermal_notify() invocation to be queued up
every time and if that takes place too often, an indefinite number of
pending work items may accumulate in kacpi_notify_wq over time.
Besides, it is not really useful to queue up a new invocation of
acpi_thermal_check() if one of them is pending already.
For these reasons, rework acpi_thermal_notify() to queue up a thermal
check instead of calling acpi_thermal_check() directly and only allow
one thermal check to be pending at a time. Moreover, only allow one
acpi_thermal_check_fn() instance at a time to run
thermal_zone_device_update() for one thermal zone and make it return
early if it sees other instances running for the same thermal zone.
While at it, fold acpi_thermal_check() into acpi_thermal_check_fn(),
as it is only called from there after the other changes made here.
[This issue appears to have been exposed by commit 6d25be5782
("sched/core, workqueues: Distangle worker accounting from rq
lock"), but it is unclear why it was not visible earlier.]
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=208877
Reported-by: Stephen Berman <stephen.berman@gmx.net>
Diagnosed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Tested-by: Stephen Berman <stephen.berman@gmx.net>
Cc: All applicable <stable@vger.kernel.org>
[bigeasy: Backported to v4.9.y, use atomic_t instead of refcount_t]
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d4a6106354 upstream.
xhci driver may in some special cases need to copy small amounts
of payload data to a bounce buffer in order to meet the boundary
and alignment restrictions set by the xHCI specification.
In the majority of these cases the data is in a sg list, and
driver incorrectly assumed data is always in urb->sg when using
the bounce buffer.
If data instead is contiguous, and in urb->transfer_buffer, we may still
need to bounce buffer a small part if data starts very close (less than
packet size) to a 64k boundary.
Check if sg list is used before copying data to/from it.
Fixes: f9c589e142 ("xhci: TD-fragment, align the unsplittable case with a bounce buffer")
Cc: stable@vger.kernel.org
Reported-by: Andreas Hartmann <andihartmann@01019freenet.de>
Tested-by: Andreas Hartmann <andihartmann@01019freenet.de>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210203113702.436762-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f670e9f9c8 upstream.
dwc2_hsotg_process_req_status uses ep_from_windex() to retrieve
the endpoint for the index provided in the wIndex request param.
In a test-case with a rndis gadget running and sending a malformed
packet to it like:
dev.ctrl_transfer(
0x82, # bmRequestType
0x00, # bRequest
0x0000, # wValue
0x0001, # wIndex
0x00 # wLength
)
it is possible to cause a crash:
[ 217.533022] dwc2 ff300000.usb: dwc2_hsotg_process_req_status: USB_REQ_GET_STATUS
[ 217.559003] Unable to handle kernel read from unreadable memory at virtual address 0000000000000088
...
[ 218.313189] Call trace:
[ 218.330217] ep_from_windex+0x3c/0x54
[ 218.348565] usb_gadget_giveback_request+0x10/0x20
[ 218.368056] dwc2_hsotg_complete_request+0x144/0x184
This happens because ep_from_windex wants to compare the endpoint
direction even if index_to_ep() didn't return an endpoint due to
the direction not matching.
The fix is easy insofar that the actual direction check is already
happening when calling index_to_ep() which will return NULL if there
is no endpoint for the targeted direction, so the offending check
can go away completely.
Fixes: c6f5c050e2 ("usb: dwc2: gadget: add bi-directional endpoint support")
Cc: stable@vger.kernel.org
Reported-by: Gerhard Klostermeier <gerhard.klostermeier@syss.de>
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Link: https://lore.kernel.org/r/20210127103919.58215-1-heiko@sntech.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 764907293e ]
While testing live partition mobility, we have observed occasional crashes
of the Linux partition. What we've seen is that during the live migration,
for specific configurations with large amounts of memory, slow network
links, and workloads that are changing memory a lot, the partition can end
up being suspended for 30 seconds or longer. This resulted in the following
scenario:
CPU 0 CPU 1
------------------------------- ----------------------------------
scsi_queue_rq migration_store
-> blk_mq_start_request -> rtas_ibm_suspend_me
-> blk_add_timer -> on_each_cpu(rtas_percpu_suspend_me
_______________________________________V
|
V
-> IPI from CPU 1
-> rtas_percpu_suspend_me
-> __rtas_suspend_last_cpu
-- Linux partition suspended for > 30 seconds --
-> for_each_online_cpu(cpu)
plpar_hcall_norets(H_PROD
-> scsi_dispatch_cmd
-> scsi_times_out
-> scsi_abort_command
-> queue_delayed_work
-> ibmvfc_queuecommand_lck
-> ibmvfc_send_event
-> ibmvfc_send_crq
- returns H_CLOSED
<- returns SCSI_MLQUEUE_HOST_BUSY
-> __blk_mq_requeue_request
-> scmd_eh_abort_handler
-> scsi_try_to_abort_cmd
- returns SUCCESS
-> scsi_queue_insert
Normally, the SCMD_STATE_COMPLETE bit would protect against the command
completion and the timeout, but that doesn't work here, since we don't
check that at all in the SCSI_MLQUEUE_HOST_BUSY path.
In this case we end up calling scsi_queue_insert on a request that has
already been queued, or possibly even freed, and we crash.
The patch below simply increases the default I/O timeout to avoid this race
condition. This is also the timeout value that nearly all IBM SAN storage
recommends setting as the default value.
Link: https://lore.kernel.org/r/1610463998-19791-1-git-send-email-brking@linux.vnet.ibm.com
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b2b0f16fa6 ]
A race condition exists between the response handler getting called because
of exchange_mgr_reset() (which clears out all the active XIDs) and the
response we get via an interrupt.
Sequence of events:
rport ba0200: Port timeout, state PLOGI
rport ba0200: Port entered PLOGI state from PLOGI state
xid 1052: Exchange timer armed : 20000 msecs xid timer armed here
rport ba0200: Received LOGO request while in state PLOGI
rport ba0200: Delete port
rport ba0200: work event 3
rport ba0200: lld callback ev 3
bnx2fc: rport_event_hdlr: event = 3, port_id = 0xba0200
bnx2fc: ba0200 - rport not created Yet!!
/* Here we reset any outstanding exchanges before
freeing rport using the exch_mgr_reset() */
xid 1052: Exchange timer canceled
/* Here we got two responses for one xid */
xid 1052: invoking resp(), esb 20000000 state 3
xid 1052: invoking resp(), esb 20000000 state 3
xid 1052: fc_rport_plogi_resp() : ep->resp_active 2
xid 1052: fc_rport_plogi_resp() : ep->resp_active 2
Skip the response if the exchange is already completed.
Link: https://lore.kernel.org/r/20201215194731.2326-1-jhasan@marvell.com
Signed-off-by: Javed Hasan <jhasan@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 9def3b1a07 upstream.
Since commit c40aaaac10 ("iommu/vt-d: Gracefully handle DMAR units
with no supported address widths") dmar.c needs struct iommu_device to
be selected. We can drop this dependency by not dereferencing struct
iommu_device if IOMMU_API is not selected and by reusing the information
stored in iommu->drhd->ignored instead.
This fixes the following build error when IOMMU_API is not selected:
drivers/iommu/dmar.c: In function ‘free_iommu’:
drivers/iommu/dmar.c:1139:41: error: ‘struct iommu_device’ has no member named ‘ops’
1139 | if (intel_iommu_enabled && iommu->iommu.ops) {
^
Fixes: c40aaaac10 ("iommu/vt-d: Gracefully handle DMAR units with no supported address widths")
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Lu Baolu <baolu.lu@linux.intel.com>
Acked-by: David Woodhouse <dwmw@amazon.co.uk>
Link: https://lore.kernel.org/r/20201013073055.11262-1-brgl@bgdev.pl
Signed-off-by: Joerg Roedel <jroedel@suse.de>
[ - context change due to moving drivers/iommu/dmar.c to
drivers/iommu/intel/dmar.c
- set the drhr in the iommu like in upstream commit b1012ca8dc
("iommu/vt-d: Skip TE disabling on quirky gfx dedicated iommu") ]
Signed-off-by: Filippo Sironi <sironi@amazon.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
