1. DMA-able memory allocated for Shadow QP was not being freed.
2. bnxt_qplib_alloc_qp_hdr_buf() had a bug wherein the SQ pointer was
erroneously pointing to the RQ. But since the corresponding
free_qp_hdr_buf() was correct, memory being free was less than what was
allocated.
Fixes: 1ac5a40479 ("RDMA/bnxt_re: Add bnxt_re RoCE driver")
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
This is dead code because j can never be 1 at this point. We had
intended to just test if the bit was clear.
Fixes: bbd8decd41 ("hwmon: (nct6775) Add support for weighted fan control")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Inside of start_xmit() the call to check if the connection is up and the
queueing of the packets for later transmission is not atomic which leaves
a window where cm_rep_handler can run, set the connection up, dequeue
pending packets and leave the subsequently queued packets by start_xmit()
sitting on neigh->queue until they're dropped when the connection is torn
down. This only applies to connected mode. These dropped packets can
really upset TCP, for example, and cause multi-minute delays in
transmission for open connections.
Here's the code in start_xmit where we check to see if the connection is
up:
if (ipoib_cm_get(neigh)) {
if (ipoib_cm_up(neigh)) {
ipoib_cm_send(dev, skb, ipoib_cm_get(neigh));
goto unref;
}
}
The race occurs if cm_rep_handler execution occurs after the above
connection check (specifically if it gets to the point where it acquires
priv->lock to dequeue pending skb's) but before the below code snippet in
start_xmit where packets are queued.
if (skb_queue_len(&neigh->queue) < IPOIB_MAX_PATH_REC_QUEUE) {
push_pseudo_header(skb, phdr->hwaddr);
spin_lock_irqsave(&priv->lock, flags);
__skb_queue_tail(&neigh->queue, skb);
spin_unlock_irqrestore(&priv->lock, flags);
} else {
++dev->stats.tx_dropped;
dev_kfree_skb_any(skb);
}
The patch acquires the netif tx lock in cm_rep_handler for the section
where it sets the connection up and dequeues and retransmits deferred
skb's.
Fixes: 839fcaba35 ("IPoIB: Connected mode experimental support")
Cc: stable@vger.kernel.org
Signed-off-by: Aaron Knister <aaron.s.knister@nasa.gov>
Tested-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Currently we always repost the recv buffer before we send a response
capsule back to the host. Since ordering is not guaranteed for send
and recv completions, it is posible that we will receive a new request
from the host before we got a send completion for the response capsule.
Today, we pre-allocate 2x rsps the length of the queue, but in reality,
under heavy load there is nothing that is really preventing the gap to
expand until we exhaust all our rsps.
To fix this, if we don't have any pre-allocated rsps left, we dynamically
allocate a rsp and make sure to free it when we are done. If under memory
pressure we fail to allocate a rsp, we silently drop the command and
wait for the host to retry.
Reported-by: Steve Wise <swise@opengridcomputing.com>
Tested-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
[hch: dropped a superflous assignment]
Signed-off-by: Christoph Hellwig <hch@lst.de>
The raspberrypi-hwmon driver doesn't automatically load, although it does work
when loaded, by adding the alias it auto loads as expected when built as a
module. Tested on RPi2/RPi3 on 32 bit kernel and RPi3B+ on aarch64 with
Fedora 28 and a patched 4.18 RC kernel.
Fixes: 3c493c885cf ("hwmon: Add support for RPi voltage sensor")
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
CC: Stefan Wahren <stefan.wahren@i2se.com>
CC: Eric Anholt <eric@anholt.net>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
add CONFIG_MEMORY_HOTREMOVE=y in config
without this config, /sys/devices/system/memory/memory*/removable
always return 0, I endup getting an early skip during test
Signed-off-by: Lei Yang <Lei.Yang@windriver.com>
Signed-off-by: Shuah Khan (Samsung OSG) <shuah@kernel.org>
Pull GPIO fixes from Linus Walleij:
"Some GPIO fixes. The ACPI stuff is probably the most annoying for
users that get fixed this time.
- Atomic contexts, cansleep* calls and such fastpath/slopwpath
things.
- Defer ACPI event handler registration to late_initcall() so IRQs do
not fire in our face before other drivers have a chance to register
handlers.
- Race condition if a consumer requests a GPIO after
gpiochip_add_data_with_key() but before of_gpiochip_add()
- Probe errorpath in the dwapb driver"
* tag 'gpio-v4.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: Fix crash due to registration race
gpio: dwapb: Fix error handling in dwapb_gpio_probe()
gpiolib-acpi: Register GpioInt ACPI event handlers from a late_initcall
gpiolib: acpi: Switch to cansleep version of GPIO library call
gpio: adp5588: Fix sleep-in-atomic-context bug
Pull SCSI fixes from James Bottomley:
"A set of very minor fixes and a couple of reverts to fix a major
problem (the attempt to change the busy count causes a hang when
attempting to change the drive cache type)"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: aacraid: fix a signedness bug
Revert "scsi: core: avoid host-wide host_busy counter for scsi_mq"
Revert "scsi: core: fix scsi_host_queue_ready"
scsi: libata: Add missing newline at end of file
scsi: target: iscsi: cxgbit: use pr_debug() instead of pr_info()
scsi: hpsa: limit transfer length to 1MB, not 512kB
scsi: lpfc: Correct MDS diag and nvmet configuration
scsi: lpfc: Default fdmi_on to on
scsi: csiostor: fix incorrect port capabilities
scsi: csiostor: add a check for NULL pointer after kmalloc()
scsi: documentation: add scsi_mod.use_blk_mq to scsi-parameters
scsi: core: Update SCSI_MQ_DEFAULT help text to match default
Pull nds32 updates from Greentime Hu:
"Contained in here are the bug fixes, building error fixes and ftrace
support for nds32"
* tag 'nds32-for-linus-4.19-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/greentime/linux:
nds32: linker script: GCOV kernel may refers data in __exit
nds32: fix build error because of wrong semicolon
nds32: Fix a kernel panic issue because of wrong frame pointer access.
nds32: Only print one page of stack when die to prevent printing too much information.
nds32: Add macro definition for offset of lp register on stack
nds32: Remove the deprecated ABI implementation
nds32/stack: Get real return address by using ftrace_graph_ret_addr
nds32/ftrace: Support dynamic function graph tracer
nds32/ftrace: Support dynamic function tracer
nds32/ftrace: Add RECORD_MCOUNT support
nds32/ftrace: Support static function graph tracer
nds32/ftrace: Support static function tracer
nds32: Extract the checking and getting pointer to a macro
nds32: Clean up the coding style
nds32: Fix get_user/put_user macro expand pointer problem
nds32: Fix empty call trace
nds32: add NULL entry to the end of_device_id array
nds32: fix logic for module
Borislav reported the following splat:
=============================
WARNING: suspicious RCU usage
4.19.0-rc1+ #1 Not tainted
-----------------------------
./include/linux/rcupdate.h:631 rcu_read_lock() used illegally while idle!
other info that might help us debug this:
RCU used illegally from idle CPU!
rcu_scheduler_active = 2, debug_locks = 1
RCU used illegally from extended quiescent state!
1 lock held by swapper/0/0:
#0: 000000004557ee0e (rcu_read_lock){....}, at: perf_event_output_forward+0x0/0x130
stack backtrace:
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.19.0-rc1+ #1
Hardware name: LENOVO 2320CTO/2320CTO, BIOS G2ET86WW (2.06 ) 11/13/2012
Call Trace:
dump_stack+0x85/0xcb
perf_event_output_forward+0xf6/0x130
__perf_event_overflow+0x52/0xe0
perf_swevent_overflow+0x91/0xb0
perf_tp_event+0x11a/0x350
? find_held_lock+0x2d/0x90
? __lock_acquire+0x2ce/0x1350
? __lock_acquire+0x2ce/0x1350
? retint_kernel+0x2d/0x2d
? find_held_lock+0x2d/0x90
? tick_nohz_get_sleep_length+0x83/0xb0
? perf_trace_cpu+0xbb/0xd0
? perf_trace_buf_alloc+0x5a/0xa0
perf_trace_cpu+0xbb/0xd0
cpuidle_enter_state+0x185/0x340
do_idle+0x1eb/0x260
cpu_startup_entry+0x5f/0x70
start_kernel+0x49b/0x4a6
secondary_startup_64+0xa4/0xb0
This is due to the tracepoints moving to SRCU usage which does not require
RCU to be "watching". But perf uses these tracepoints with RCU and expects
it to be. Hence, we still need to add in the rcu_irq_enter/exit_irqson()
calls for "rcuidle" tracepoints. This is a temporary fix until we have SRCU
working in NMI context, and then perf can be converted to use that instead
of normal RCU.
Link: http://lkml.kernel.org/r/20180904162611.6a120068@gandalf.local.home
Cc: x86-ml <x86@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Reported-by: Borislav Petkov <bp@alien8.de>
Tested-by: Borislav Petkov <bp@alien8.de>
Reviewed-by: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Fixes: e6753f23d9 ("tracepoint: Make rcuidle tracepoint callers use SRCU")
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
With performance optimization the spi transfer and messages of basic
register operations like qcaspi_read_register moved into the private
driver structure. But they weren't protected against mutual access
(e.g. between driver kthread and ethtool). So dumping the QCA7000
registers via ethtool during network traffic could make spi_sync
hang forever, because the completion in spi_message is overwritten.
So revert the optimization completely.
Fixes: 291ab06ecf ("net: qualcomm: new Ethernet over SPI driver for QCA700")
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DMA allocated memory is lost in be_cmd_get_profile_config() when we
call it with non-NULL port_res parameter.
Signed-off-by: Petr Oros <poros@redhat.com>
Reviewed-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the following sparse warning:
drivers/net/ethernet/microchip/lan743x_ptp.c:980:6: warning:
symbol 'lan743x_ptp_set_sync_ts_insert' was not declared. Should it be static?
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the following sparse warning:
drivers/net/ethernet/mellanox/mlx5/core/ipoib/ipoib.c:119:6: warning:
symbol 'mlx5i_grp_sw_update_stats' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MC-aware mode was recently enabled by mlxsw on Spectrum switches in
commit 7b81953066 ("mlxsw: spectrum: Configure MC-aware mode on mlxsw
ports"). Unfortunately, testing has shown that the fix is incomplete and
in the presented form actually makes the problem even worse, because any
amount of MC traffic causes UC disruption.
The reason for this is that currently, mlxsw configures the MC-specific
TCs (8..15) to map to pool 0. It also configures a maximum buffer size
of 0, but for MC traffic that maximum is disregarded and not part of the
quota. Therefore MC traffic is always admitted to the egress buffer.
Fix the configuration by directing the MC TCs into pool 15, which is
dedicated to MC traffic and recognized as such by the silicon.
Fixes: 7b81953066 ("mlxsw: spectrum: Configure MC-aware mode on mlxsw ports")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johannes Berg says:
====================
This time, we have some pretty impactful work. Among
the changes:
* changes to make PTK rekeying work better, or actually
better/safely if drivers get updated
* VHT extended NSS support - some APs had capabilities
that didn't fit into the VHT (11ac) spec, so the spec
was updated and we follow that now
* some TXQ and A-MSDU building work - will allow iwlwifi
to use this soon
* more HE work, including aligning to 802.11ax Draft 3.0
* L-SIG and 0-length-PSDU support in radiotap
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Johan writes:
USB-serial fixes for v4.19-rc3
Here are two fixes for array-underflow bugs in completion handlers due
to insufficient sanity checks.
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
If the kernel headers aren't installed we can't build all the tests.
Add a new make target rule 'khdr' in the file lib.mk to generate the
kernel headers and that gets include for every test-dir Makefile that
includes lib.mk If the testdir in turn have its own sub-dirs the
top_srcdir needs to be set to the linux-rootdir to be able to generate
the kernel headers.
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Reviewed-by: Fathi Boudra <fathi.boudra@linaro.org>
Signed-off-by: Shuah Khan (Samsung OSG) <shuah@kernel.org>
wdm_in_callback() is a completion handler function for the USB driver.
So it should not sleep. But it calls service_outstanding_interrupt(),
which calls usb_submit_urb() with GFP_KERNEL.
To fix this bug, GFP_KERNEL is replaced with GFP_ATOMIC.
This bug is found by my static analysis tool DSAC.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
async_complete() in uss720.c is a completion handler function for the
USB driver. So it should not sleep, but it is can sleep according to the
function call paths (from bottom to top) in Linux-4.16.
[FUNC] set_1284_register(GFP_KERNEL)
drivers/usb/misc/uss720.c, 372:
set_1284_register in parport_uss720_frob_control
drivers/parport/ieee1284.c, 560:
[FUNC_PTR]parport_uss720_frob_control in parport_ieee1284_ack_data_avail
drivers/parport/ieee1284.c, 577:
parport_ieee1284_ack_data_avail in parport_ieee1284_interrupt
./include/linux/parport.h, 474:
parport_ieee1284_interrupt in parport_generic_irq
drivers/usb/misc/uss720.c, 116:
parport_generic_irq in async_complete
[FUNC] get_1284_register(GFP_KERNEL)
drivers/usb/misc/uss720.c, 382:
get_1284_register in parport_uss720_read_status
drivers/parport/ieee1284.c, 555:
[FUNC_PTR]parport_uss720_read_status in parport_ieee1284_ack_data_avail
drivers/parport/ieee1284.c, 577:
parport_ieee1284_ack_data_avail in parport_ieee1284_interrupt
./include/linux/parport.h, 474:
parport_ieee1284_interrupt in parport_generic_irq
drivers/usb/misc/uss720.c, 116:
parport_generic_irq in async_complete
Note that [FUNC_PTR] means a function pointer call is used.
To fix these bugs, GFP_KERNEL is replaced with GFP_ATOMIC.
These bugs are found by my static analysis tool DSAC.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
i_usX2Y_subs_startup in usbusx2yaudio.c is a completion handler function
for the USB driver. So it should not sleep, but it is can sleep
according to the function call paths (from bottom to top) in Linux-4.16.
[FUNC] msleep
drivers/usb/host/u132-hcd.c, 2558:
msleep in u132_get_frame
drivers/usb/core/hcd.c, 2231:
[FUNC_PTR]u132_get_frame in usb_hcd_get_frame_number
drivers/usb/core/usb.c, 822:
usb_hcd_get_frame_number in usb_get_current_frame_number
sound/usb/usx2y/usbusx2yaudio.c, 303:
usb_get_current_frame_number in i_usX2Y_urb_complete
sound/usb/usx2y/usbusx2yaudio.c, 366:
i_usX2Y_urb_complete in i_usX2Y_subs_startup
Note that [FUNC_PTR] means a function pointer call is used.
To fix this bug, msleep() is replaced with mdelay().
This bug is found by my static analysis tool DSAC.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The steps taken by usb core to set a new interface is very different from
what is done on the xHC host side.
xHC hardware will do everything in one go. One command is used to set up
new endpoints, free old endpoints, check bandwidth, and run the new
endpoints.
All this is done by xHC when usb core asks the hcd to check for
available bandwidth. At this point usb core has not yet flushed the old
endpoints, which will cause use-after-free issues in xhci driver as
queued URBs are cancelled on a re-allocated endpoint.
To resolve this add a call to usb_disable_interface() which will flush
the endpoints before calling usb_hcd_alloc_bandwidth()
Additional checks in xhci driver will also be implemented to gracefully
handle stale URB cancel on freed and re-allocated endpoints
Cc: <stable@vger.kernel.org>
Reported-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix kernel-doc warning for missing struct member description:
../include/linux/mod_devicetable.h:763: warning: Function parameter or member 'driver_data' not described in 'typec_device_id'
Fixes: 8a37d87d72 ("usb: typec: Bus type for alternate modes")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix kernel-doc warning for missing function parameter 'mode' description:
../drivers/usb/typec/bus.c:268: warning: Function parameter or member 'mode' not described in 'typec_match_altmode'
Also fix typos for same function documentation.
Fixes: 8a37d87d72 ("usb: typec: Bus type for alternate modes")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb_hc_died() should only be called once, and with the primary HCD
as parameter. It will mark both primary and secondary hcd's dead.
Remove the extra call to usb_cd_died with the shared hcd as parameter.
Fixes: ff9d78b36f ("USB: Set usb_hcd->state and flags for shared roothubs")
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since I'm leaving from Socionext, I'll unable to access specification
documents of this hardware (these are not public). So change the
state to orphan until someone will maintain this driver.
Signed-off-by: Katsuhiro Suzuki <suzuki.katsuhiro@socionext.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If dual role mode is enabled, when switch u3port0 to device mode,
it will affect port id calculation of host(xHCI), specially when
host supports multi U2 ports or U3 ports, so need enable its dual
role mode, and fix it here.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The hope that UAS devices would be less broken than old style storage
devices has turned out to be unfounded. Make UAS support more of the
quirk flags of the old driver.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This device does not correctly handle the LPM operations.
Also, the device cannot handle ATA pass-through commands
and locks up when attempted while running in super speed.
This patch adds the equivalent quirk logic as found in uas.
Signed-off-by: Tim Anderson <tsa@biglakesoftware.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
snprintf() always returns the full length of the string it could have
printed, even if it was truncated because the buffer was too small.
So in case the counter value is truncated, we will over-read from
in_buffer and over-write to the caller's buffer.
I don't think it's actually possible for this to happen, but in case
truncation occurs, WARN and return -EIO.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In xhci_plat_probe() both sysdev and pdev->dev are being used
for finding quirks. There are some drivers(like dwc3 host.c)
which adds quirks(like usb3-lpm-capable) into pdev and the logic
present in xhci_plat_probe() checks for quirks in either sysdev
or pdev for finding the quirks. Because of this logic, some of
the quirks are getting missed(usb3-lpm-capable quirk added by dwc3
host.c driver is getting missed).This patch fixes this by iterating
over all the available parents for finding the quirks. In this way
all the quirks which are present in child or parent are correctly
updated.
Signed-off-by: Anurag Kumar Vulisha <anurag.kumar.vulisha@xilinx.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure the cancelled URB is on the current endpoint ring.
If the endpoint ring has been reallocated since the URB was enqueued
then the URB may contain TD and TRB pointers to a already freed ring.
In this the case return the URB without touching any of the freed ring
structure data.
Don't try to stop the ring. It would be useless.
This can occur if endpoint is not flushed before it is dropped and
re-added, which is the case in usb_set_interface() as xhci does
things in an odd order.
Cc: <stable@vger.kernel.org>
Tested-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some SoC/IP as STM32F469, the snpsid can only be read after clock is
enabled, otherwise it will read as 0, and the dwc2_check_core_endianness
will assume the core and AHB have opposite endianness, leading to the
following error:
[ 1.976339] dwc2 50000000.usb: 50000000.usb supply vusb_d not found, using dummy regulator
[ 1.986124] dwc2 50000000.usb: Linked as a consumer to regulator.0
[ 1.992711] dwc2 50000000.usb: 50000000.usb supply vusb_a not found, using dummy regulator
[ 2.003672] dwc2 50000000.usb: dwc2_core_reset: HANG! AHB Idle timeout GRSTCTL GRSTCTL_AHBIDLE
[ 2.015176] dwc2: probe of 50000000.usb failed with error -16
The proposed patch changes the location where dwc2_check_core_endianness
is called, allowing the clock peripheral to be enabled first.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Bruno Meirelles Herrera <bmh@certi.org.br>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Commit b0f847e16c ("HID: hid-sensor-hub: Force logical minimum to 1 for
power and report state") not only replaced the descriptor fixup done for
devices with the HID_SENSOR_HUB_ENUM_QUIRK with a generic fix, but also
accidentally removed the unrelated descriptor fixup for the Lenovo ThinkPad
Helix 2 sensor hub. This commit restores this fixup.
Restoring this fixup not only fixes the Lenovo ThinkPad Helix 2's sensors,
but also the Lenovo ThinkPad 8's sensors.
Fixes: b0f847e16c ("HID: hid-sensor-hub: Force logical minimum ...")
Cc: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Cc: Fernando D S Lima <fernandodsl@gmail.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add validation check for wmm rule when copy rules from fwdb and print
error when rule is invalid.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Both old and new cannot be NULL at the same time, hence checking
new when old is not NULL is unnecessary.
Also, notice that new is being dereferenced before it is checked:
idx = new->conf.keyidx;
The above triggers a static code analysis warning.
Address this by removing the NULL check on new and adding a code
comment based on the following piece of code:
387 /* caller must provide at least one old/new */
388 if (WARN_ON(!new && !old))
389 return 0;
Addresses-Coverity-ID: 1473176 ("Dereference before null check")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some hardwares have limitations on the packets' type in AMSDU.
Add an optional driver callback to determine if two skbs can
be used in the same AMSDU or not.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We have a TXQ abstraction for non-data packets that need
powersave buffering. Since the AP cannot sleep, in case
of station we can use this TXQ for all management frames,
regardless if they are bufferable. Add HW flag to allow
that.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Align to new 11ax draft D3.0. Change/add new MAC and PHY capabilities
and update drivers' 11ax capabilities and mac80211's debugfs
accordingly.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
After masking the he_oper_params, to get the requested values as
integers one must rshift and not lshift. Fix that by using the
le32_get_bits() macro.
Fixes: 41cbb0f5a2 ("mac80211: add support for HE")
Signed-off-by: Naftali Goldstein <naftali.goldstein@intel.com>
[converted to use le32_get_bits()]
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For certain sounding frames, it may be useful to report them
to userspace even though they don't have a PSDU in order to
determine the PHY parameters (e.g. VHT rate/stream config.)
Add support for this to mac80211.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There is a NULL pointer dereference in case memory resources
for *parse* are not successfully allocated.
Fix this by adding a new goto label and make the execution
path jump to it in case vzalloc() fails.
Addresses-Coverity-ID: 1473081 ("Dereference after null check")
Fixes: b2dd9f2e5a ("HID: core: fix memory leak on probe")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Rekeying PTK keys without "Extended Key ID for Individually Addressed
Frames" did use a procedure not suitable to replace in-use keys and
could caused the following issues:
1) Freeze caused by incoming frames:
If the local STA installed the key prior to the remote STA we still
had the old key active in the hardware when mac80211 switched over
to the new key.
Therefore there was a window where the card could hand over frames
decoded with the old key to mac80211 and bump the new PN (IV) value
to an incorrect high number. When it happened the local replay
detection silently started to drop all frames sent with the new key.
2) Freeze caused by outgoing frames:
If mac80211 was providing the PN (IV) and handed over a clear text
frame for encryption to the hardware prior to a key change the
driver/card could have processed the queued frame after switching
to the new key. This bumped the PN value on the remote STA to an
incorrect high number, tricking the remote STA to discard all frames
we sent later.
3) Freeze caused by RX aggregation reorder buffer:
An aggregation session started with the old key and ending after the
switch to the new key also bumped the PN to an incorrect high number,
freezing the connection quite similar to 1).
4) Freeze caused by repeating lost frames in an aggregation session:
A driver could repeat a lost frame and encrypt it with the new key
while in a TX aggregation session without updating the PN for the
new key. This also could freeze connections similar to 2).
5) Clear text leak:
Removing encryption offload from the card cleared the encryption
offload flag only after the card had deleted the key and we did not
stop TX during the rekey. The driver/card could therefore get
unencrypted frames from mac80211 while no longer be instructed to
encrypt them.
To prevent those issues the key install logic has been changed:
- Mac80211 divers known to be able to rekey PTK0 keys have to set
@NL80211_EXT_FEATURE_CAN_REPLACE_PTK0,
- mac80211 stops queuing frames depending on the key during the replace
- the key is first replaced in the hardware and after that in mac80211
- and mac80211 stops/blocks new aggregation sessions during the rekey.
For drivers not setting
@NL80211_EXT_FEATURE_CAN_REPLACE_PTK0 the user space must avoid PTK
rekeys if "Extended Key ID for Individually Addressed Frames" is not
being used. Rekeys for mac80211 drivers without this flag will generate a
warning and use an extra call to ieee80211_flush_queues() to both
highlight and try to prevent the issues with not updated drivers.
The core of the fix changes the key install procedure from:
- atomic switch over to the new key in mac80211
- remove the old key in the hardware (stops encryption offloading, fall
back to software encryption with a potential clear text packet leak
in between)
- delete the inactive old key in mac80211
- enable hardware encryption offloading for the new key
to:
- if it's a PTK mark the old key as tainted to drop TX frames with the
outgoing key
- replace the key in hardware with the new one
- atomic switch over to the new (not marked as tainted) key in
mac80211 (which also resumes TX)
- delete the inactive old key in mac80211
With the new sequence the hardware will be unable to decrypt frames
encrypted with the old key prior to switching to the new key in mac80211
and thus prevent PNs from packets decrypted with the old key to be
accounted against the new key.
For that to work the drivers have to provide a clear boundary.
Mac80211 drivers setting @NL80211_EXT_FEATURE_CAN_REPLACE_PTK0 confirm
to provide it and mac80211 will then be able to correctly rekey in-use
PTK keys with those drivers.
The mac80211 requirements for drivers to set the flag have been added to
the "Hardware crypto acceleration" documentation section. It drills down
to:
The drivers must not hand over frames decrypted with the old key to
mac80211 once the call to set_key() with %DISABLE_KEY has been
completed. It's allowed to either drop or continue to use the old key
for any outgoing frames which are already in the queues, but it must not
send out any of them unencrypted or encrypted with the new key.
Even with the new boundary in place aggregation sessions with the
reorder buffer are problematic:
RX aggregation session started prior and completed after the rekey could
still dump frames received with the old key at mac80211 after it
switched over to the new key. This is side stepped by stopping all (RX
and TX) aggregation sessions when replacing a PTK key and hardware key
offloading.
Stopping TX aggregation sessions avoids the need to get
the PNs (IVs) updated in frames prepared for the old key and
(re)transmitted after the switch to the new key. As a bonus it improves
the compatibility when the remote STA is not handling rekeys as it
should.
When using software crypto aggregation sessions are not stopped.
Mac80211 won't be able to decode the dangerous frames and discard them
without special handling.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
[trim overly long rekey warning]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Drivers able to correctly replace a in-use key should set
@NL80211_EXT_FEATURE_CAN_REPLACE_PTK0 to allow the user space (e.g.
hostapd or wpa_supplicant) to rekey PTK keys.
The user space must detect a PTK rekey attempt and only go ahead with it
when the driver has set this flag. If the driver is not supporting the
feature the user space either must not replace the PTK key or perform a
full re-association instead.
Ignoring this flag and continuing to rekey the connection can still work
but has to be considered insecure and broken. Depending on the driver it
can leak clear text packets or freeze the connection and is only
supported to allow the user space to be updated.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
Reviewed-by: Denis Kenzior <denkenz@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
