[ Upstream commit 804d8e0a6e ]
OPDESC() simply indexes into nfsd4_ops[] by the op's operation
number, without range checking that value. It assumes callers are
careful to avoid calling it with an out-of-bounds opnum value.
nfsd4_decode_compound() is not so careful, and can invoke OPDESC()
with opnum set to OP_ILLEGAL, which is 10044 -- well beyond the end
of nfsd4_ops[].
Reported-by: Jeff Layton <jlayton@kernel.org>
Fixes: f4f9ef4a1b ("nfsd4: opdesc will be useful outside nfs4proc.c")
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e4efa515d5 ]
After commit 92cadedd9d ("brcmfmac: Avoid keeping power to SDIO card
unless WOWL is used"), the wifi adapter by default is turned off on suspend
and then re-probed on resume.
In at least 2 model x86/acpi tablets with brcmfmac43430a1 wifi adapters,
the newly added re-probe on resume fails like this:
brcmfmac: brcmf_sdio_bus_rxctl: resumed on timeout
ieee80211 phy1: brcmf_bus_started: failed: -110
ieee80211 phy1: brcmf_attach: dongle is not responding: err=-110
brcmfmac: brcmf_sdio_firmware_callback: brcmf_attach failed
It seems this specific brcmfmac model does not like being reprobed without
it actually being turned off first.
And the adapter is not being turned off during suspend because of
commit f0992ace68 ("brcmfmac: prohibit ACPI power management for brcmfmac
driver").
Now that the driver is being reprobed on resume, the disabling of ACPI
pm is no longer necessary, except when WOWL is used (in which case there
is no-reprobe).
Move the dis-/en-abling of ACPI pm to brcmf_sdio_wowl_config(), this fixes
the brcmfmac43430a1 suspend/resume regression and should help save some
power when suspended.
This change means that the code now also may re-enable ACPI pm when WOWL
gets disabled. ACPI pm should only be re-enabled if it was enabled by
the ACPI core originally. Add a brcmf_sdiod_acpi_save_power_manageable()
to save the original state for this.
This has been tested on the following devices:
Asus T100TA brcmfmac43241b4-sdio
Acer Iconia One 7 B1-750 brcmfmac43340-sdio
Chuwi Hi8 brcmfmac43430a0-sdio
Chuwi Hi8 brcmfmac43430a1-sdio
(the Asus T100TA is the device for which the prohibiting of ACPI pm
was originally added)
Fixes: 92cadedd9d ("brcmfmac: Avoid keeping power to SDIO card unless WOWL is used")
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230320122252.240070-1-hdegoede@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 154e07c164 ]
Commit 65b32f801b ("uapi: move IPPROTO_L2TP to in.h") moved the
definition of IPPROTO_L2TP from a define to an enum, but since
__stringify doesn't work properly with enums, we ended up breaking the
modalias strings for the l2tp modules:
$ modinfo l2tp_ip l2tp_ip6 | grep alias
alias: net-pf-2-proto-IPPROTO_L2TP
alias: net-pf-2-proto-2-type-IPPROTO_L2TP
alias: net-pf-10-proto-IPPROTO_L2TP
alias: net-pf-10-proto-2-type-IPPROTO_L2TP
Use the resolved number directly in MODULE_ALIAS_*() macros (as we
already do with SOCK_DGRAM) to fix the alias strings:
$ modinfo l2tp_ip l2tp_ip6 | grep alias
alias: net-pf-2-proto-115
alias: net-pf-2-proto-115-type-2
alias: net-pf-10-proto-115
alias: net-pf-10-proto-115-type-2
Moreover, fix the ordering of the parameters passed to
MODULE_ALIAS_NET_PF_PROTO_TYPE() by switching proto and type.
Fixes: 65b32f801b ("uapi: move IPPROTO_L2TP to in.h")
Link: https://lore.kernel.org/lkml/ZCQt7hmodtUaBlCP@righiandr-XPS-13-7390
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: Andrea Righi <andrea.righi@canonical.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Tested-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6fc21a6ed5 ]
Currently, intel_speed_mode_2500() will fix-up xpcs_an_inband
to 1 if the underlying controller has a max speed of 1000Mbps.
The value has been initialized and modified if it is
a fixed-linked setup earlier.
This patch removes the fix-up to allow for fixed-linked setup
support. In stmmac_phy_setup(), ovr_an_inband is set based on
the value of xpcs_an_inband. Which in turn will return an
error in phylink_parse_mode() where MLO_AN_FIXED and
ovr_an_inband are both set.
Fixes: c82386310d ("stmmac: intel: prepare to support 1000BASE-X phy interface setting")
Signed-off-by: Michael Sit Wei Hong <michael.wei.hong.sit@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fe2cfbc968 ]
After the introduction of the fixed-link support, the MAC driver
no longer attempt to scan for a PHY to attach to. This causes the
non fixed-link setups to stop working.
Using the phylink_expects_phy() to check and determine if the MAC
should expect and attach a PHY.
Fixes: ab21cf9209 ("net: stmmac: make mdio register skips PHY scanning for fixed-link")
Signed-off-by: Michael Sit Wei Hong <michael.wei.hong.sit@intel.com>
Signed-off-by: Lai Peter Jun Ann <peter.jun.ann.lai@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 653a180957 ]
Provide phylink_expects_phy() to allow MAC drivers to check if it
is expecting a PHY to attach to. Since fixed-linked setups do not
need to attach to a PHY.
Provides a boolean value as to if the MAC should expect a PHY.
Returns true if a PHY is expected.
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Michael Sit Wei Hong <michael.wei.hong.sit@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: fe2cfbc968 ("net: stmmac: check if MAC needs to attach to a PHY")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 21f27df854 ]
To determine whether the guest has caused an external interruption loop
upon code 20 (external interrupt) intercepts, the ext_new_psw needs to
be inspected to see whether external interrupts are enabled.
Under non-PV, ext_new_psw can simply be taken from guest lowcore. Under
PV, KVM can only access the encrypted guest lowcore and hence the
ext_new_psw must not be taken from guest lowcore.
handle_external_interrupt() incorrectly did that and hence was not able
to reliably tell whether an external interruption loop is happening or
not. False negatives cause spurious failures of my kvm-unit-test
for extint loops[1] under PV.
Since code 20 is only caused under PV if and only if the guest's
ext_new_psw is enabled for external interrupts, false positive detection
of a external interruption loop can not happen.
Fix this issue by instead looking at the guest PSW in the state
description. Since the PSW swap for external interrupt is done by the
ultravisor before the intercept is caused, this reliably tells whether
the guest is enabled for external interrupts in the ext_new_psw.
Also update the comments to explain better what is happening.
[1] https://lore.kernel.org/kvm/20220812062151.1980937-4-nrb@linux.ibm.com/
Signed-off-by: Nico Boehr <nrb@linux.ibm.com>
Reviewed-by: Janosch Frank <frankja@linux.ibm.com>
Reviewed-by: Christian Borntraeger <borntraeger@linux.ibm.com>
Fixes: 201ae986ea ("KVM: s390: protvirt: Implement interrupt injection")
Link: https://lore.kernel.org/r/20230213085520.100756-2-nrb@linux.ibm.com
Message-Id: <20230213085520.100756-2-nrb@linux.ibm.com>
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a4a3203426 ]
The order in which clocks are stopped matters as some of the clock
like NPL are derived from MCLK.
Without this patch, Dragonboard RB5 DSP would crash with below error:
qcom_q6v5_pas 17300000.remoteproc: fatal error received:
ABT_dal.c:278:ABTimeout: AHB Bus hang is detected,
Number of bus hang detected := 2 , addr0 = 0x3370000 , addr1 = 0x0!!!
Turn off fsgen first, followed by npl and then finally mclk, which is exactly
the opposite order of enable sequence.
Fixes: 1dc3459009 ("ASoC: codecs: lpass: register mclk after runtime pm")
Reported-by: Amit Pundir <amit.pundir@linaro.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Tested-by: Amit Pundir <amit.pundir@linaro.org>
Link: https://lore.kernel.org/r/20230323110125.23790-1-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8caa81eb95 ]
The driver only supports normal polarity. Complete the implementation of
.get_state() by setting .polarity accordingly.
This fixes a regression that was possible since commit c73a310762
("pwm: Handle .get_state() failures") which stopped to zero-initialize
the state passed to the .get_state() callback. This was reported at
https://forum.odroid.com/viewtopic.php?f=177&t=46360 . While this was an
unintended side effect, the real issue is the driver's callback not
setting the polarity.
There is a complicating fact, that the .apply() callback fakes support
for inversed polarity. This is not (and cannot) be matched by
.get_state(). As fixing this isn't easy, only point it out in a comment
to prevent authors of other drivers from copying that approach.
Fixes: c375bcbaab ("pwm: meson: Read the full hardware state in meson_pwm_get_state()")
Reported-by: Munehisa Kamata <kamatam@amazon.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20230310191405.2606296-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6c452cff79 ]
.get_state() might fail in some cases. To make it possible that a driver
signals such a failure change the prototype of .get_state() to return an
error code.
This patch was created using coccinelle and the following semantic patch:
@p1@
identifier getstatefunc;
identifier driver;
@@
struct pwm_ops driver = {
...,
.get_state = getstatefunc
,...
};
@p2@
identifier p1.getstatefunc;
identifier chip, pwm, state;
@@
-void
+int
getstatefunc(struct pwm_chip *chip, struct pwm_device *pwm, struct pwm_state *state)
{
...
- return;
+ return 0;
...
}
plus the actual change of the prototype in include/linux/pwm.h (plus some
manual fixing of indentions and empty lines).
So for now all drivers return success unconditionally. They are adapted
in the following patches to make the changes easier reviewable.
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Baolin Wang <baolin.wang@linux.alibaba.com>
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Acked-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20221130152148.2769768-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Stable-dep-of: 6f57937980 ("pwm: hibvt: Explicitly set .polarity in .get_state()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1eb65c8687 ]
relid2channel() assumes vmbus channel array to be allocated when called.
However, in cases such as kdump/kexec, not all relids will be reset by the host.
When the second kernel boots and if the guest receives a vmbus interrupt during
vmbus driver initialization before vmbus_connect() is called, before it finishes,
or if it fails, the vmbus interrupt service routine is called which in turn calls
relid2channel() and can cause a null pointer dereference.
Print a warning and error out in relid2channel() for a channel id that's invalid
in the second kernel.
Fixes: 8b6a877c06 ("Drivers: hv: vmbus: Replace the per-CPU channel lists with a global array of channels")
Signed-off-by: Mohammed Gamal <mgamal@redhat.com>
Reviewed-by: Dexuan Cui <decui@microsoft.com>
Link: https://lore.kernel.org/r/20230217204411.212709-1-mgamal@redhat.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d49765b5f4 ]
REGMAP is a hidden (not user visible) symbol. Users cannot set it
directly thru "make *config", so drivers should select it instead of
depending on it if they need it.
Consistently using "select" or "depends on" can also help reduce
Kconfig circular dependency issues.
Therefore, change the use of "depends on REGMAP" to "select REGMAP".
Fixes: ebe363197e ("gpio: add a reusable generic gpio_chip using regmap")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Michael Walle <michael@walle.cc>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Bartosz Golaszewski <brgl@bgdev.pl>
Cc: linux-gpio@vger.kernel.org
Acked-by: Michael Walle <michael@walle.cc>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f6da81f650 ]
Presently, when a guest writes 1 to PMCR_EL0.{C,P}, which is WO/RAZ,
KVM saves the register value, including these bits.
When userspace reads the register using KVM_GET_ONE_REG, KVM returns
the saved register value as it is (the saved value might have these
bits set). This could result in userspace setting these bits on the
destination during migration. Consequently, KVM may end up resetting
the vPMU counter registers (PMCCNTR_EL0 and/or PMEVCNTR<n>_EL0) to
zero on the first KVM_RUN after migration.
Fix this by not saving those bits when a guest writes 1 to those bits.
Fixes: ab9468340d ("arm64: KVM: Add access handler for PMCR register")
Cc: stable@vger.kernel.org
Reviewed-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Reiji Watanabe <reijiw@google.com>
Link: https://lore.kernel.org/r/20230313033234.1475987-1-reijiw@google.com
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 64d6820d64 ]
Userspace can play some dirty tricks on us by selecting a given
PMU version (such as PMUv3p5), restore a PMCR_EL0 value that
has PMCR_EL0.LP set, and then switch the PMU version to PMUv3p1,
for example. In this situation, we end-up with PMCR_EL0.LP being
set and spreading havoc in the PMU emulation.
This is specially hard as the first two step can be done on
one vcpu and the third step on another, meaning that we need
to sanitise *all* vcpus when the PMU version is changed.
In orer to avoid a pretty complicated locking situation,
defer the sanitisation of PMCR_EL0 to the point where the
vcpu is actually run for the first tine, using the existing
KVM_REQ_RELOAD_PMU request that calls into kvm_pmu_handle_pmcr().
There is still an obscure corner case where userspace could
do the above trick, and then save the VM without running it.
They would then observe an inconsistent state (PMUv3.1 + LP set),
but that state will be fixed on the first run anyway whenever
the guest gets restored on a host.
Reported-by: Reiji Watanabe <reijiw@google.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Stable-dep-of: f6da81f650 ("KVM: arm64: PMU: Don't save PMCR_EL0.{C,P} for the vCPU")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c82d28cbf1 ]
The PMU architecture makes a subtle difference between a 64bit
counter and a counter that has a 64bit overflow. This is for example
the case of the cycle counter, which can generate an overflow on
a 32bit boundary if PMCR_EL0.LC==0 despite the accumulation being
done on 64 bits.
Use this distinction in the few cases where it matters in the code,
as we will reuse this with PMUv3p5 long counters.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20221113163832.3154370-5-maz@kernel.org
Stable-dep-of: f6da81f650 ("KVM: arm64: PMU: Don't save PMCR_EL0.{C,P} for the vCPU")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bead02204e ]
Ricardo recently pointed out that the PMU chained counter emulation
in KVM wasn't quite behaving like the one on actual hardware, in
the sense that a chained counter would expose an overflow on
both halves of a chained counter, while KVM would only expose the
overflow on the top half.
The difference is subtle, but significant. What does the architecture
say (DDI0087 H.a):
- Up to PMUv3p4, all counters but the cycle counter are 32bit
- A 32bit counter that overflows generates a CHAIN event on the
adjacent counter after exposing its own overflow status
- The CHAIN event is accounted if the counter is correctly
configured (CHAIN event selected and counter enabled)
This all means that our current implementation (which uses 64bit
perf events) prevents us from emulating this overflow on the lower half.
How to fix this? By implementing the above, to the letter.
This largely results in code deletion, removing the notions of
"counter pair", "chained counters", and "canonical counter".
The code is further restructured to make the CHAIN handling similar
to SWINC, as the two are now extremely similar in behaviour.
Reported-by: Ricardo Koller <ricarkol@google.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Reiji Watanabe <reijiw@google.com>
Link: https://lore.kernel.org/r/20221113163832.3154370-3-maz@kernel.org
Stable-dep-of: f6da81f650 ("KVM: arm64: PMU: Don't save PMCR_EL0.{C,P} for the vCPU")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f7b58a69fa ]
"Abnormal" bios include discards, write zeroes and secure erase. By no
longer passing the calculated 'len' pointer, commit 7dd06a2548 ("dm:
allow dm_accept_partial_bio() for dm_io without duplicate bios") took a
senseless approach to disallowing dm_accept_partial_bio() from working
for duplicate bios processed using __send_duplicate_bios().
It inadvertently and incorrectly stopped the use of 'len' when
initializing a target's io (in alloc_tio). As such the resulting tio
could address more area of a device than it should.
For example, when discarding an entire DM striped device with the
following DM table:
vg-lvol0: 0 159744 striped 2 128 7:0 2048 7:1 2048
vg-lvol0: 159744 45056 striped 2 128 7:2 2048 7:3 2048
Before this fix:
device-mapper: striped: target_stripe=0, bdev=7:0, start=2048 len=102400
blkdiscard: attempt to access beyond end of device
loop0: rw=2051, sector=2048, nr_sectors = 102400 limit=81920
device-mapper: striped: target_stripe=1, bdev=7:1, start=2048 len=102400
blkdiscard: attempt to access beyond end of device
loop1: rw=2051, sector=2048, nr_sectors = 102400 limit=81920
After this fix;
device-mapper: striped: target_stripe=0, bdev=7:0, start=2048 len=79872
device-mapper: striped: target_stripe=1, bdev=7:1, start=2048 len=79872
Fixes: 7dd06a2548 ("dm: allow dm_accept_partial_bio() for dm_io without duplicate bios")
Cc: stable@vger.kernel.org
Reported-by: Orange Kao <orange@aiven.io>
Signed-off-by: Mike Snitzer <snitzer@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
This reverts commit 07fc78d8f0 which was
upstream commit 6d9c7f51b1.
Lockdep warnings on boot that are not seen with Linus's tree.
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 8eeddc0d42 upstream.
During miration to vram prange->offset is valid after vram buffer is located,
either use old one or allocate a new one. Move svm_range_vram_node_new before
migrate for each vma to get valid prange->offset.
v2: squash in warning fix
Fixes: b4ee960637 ("drm/amdkfd: Fix BO offset for multi-VMA page migration")
Signed-off-by: Xiaogang Chen <Xiaogang.Chen@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0482c34ec6 upstream.
ucsi_init() which runs from a workqueue sets ucsi->connector and
on an error will clear it again.
ucsi->connector gets dereferenced by ucsi_resume(), this checks for
ucsi->connector being NULL in case ucsi_init() has not finished yet;
or in case ucsi_init() has failed.
ucsi_init() setting ucsi->connector and then clearing it again on
an error creates a race where the check in ucsi_resume() may pass,
only to have ucsi->connector free-ed underneath it when ucsi_init()
hits an error.
Fix this race by making ucsi_init() store the connector array in
a local variable and only assign it to ucsi->connector on success.
Fixes: bdc62f2bae ("usb: typec: ucsi: Simplified registration and I/O API")
Cc: stable@vger.kernel.org
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230308154244.722337-3-hdegoede@redhat.com
Signed-off-by: Joakim Tjernlund <joakim.tjernlund@infinera.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4fb877aaa1 ]
Fix bug in btf_dump's logic of determining if a given struct type is
packed or not. The notion of "natural alignment" is not needed and is
even harmful in this case, so drop it altogether. The biggest difference
in btf_is_struct_packed() compared to its original implementation is
that we don't really use btf__align_of() to determine overall alignment
of a struct type (because it could be 1 for both packed and non-packed
struct, depending on specifci field definitions), and just use field's
actual alignment to calculate whether any field is requiring packing or
struct's size overall necessitates packing.
Add two simple test cases that demonstrate the difference this change
would make.
Fixes: ea2ce1ba99 ("libbpf: Fix BTF-to-C converter's padding logic")
Reported-by: Eduard Zingerman <eddyz87@gmail.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Eduard Zingerman <eddyz87@gmail.com>
Link: https://lore.kernel.org/bpf/20221215183605.4149488-1-andrii@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ea2ce1ba99 ]
Turns out that btf_dump API doesn't handle a bunch of tricky corner
cases, as reported by Per, and further discovered using his testing
Python script ([0]).
This patch revamps btf_dump's padding logic significantly, making it
more correct and also avoiding unnecessary explicit padding, where
compiler would pad naturally. This overall topic turned out to be very
tricky and subtle, there are lots of subtle corner cases. The comments
in the code tries to give some clues, but comments themselves are
supposed to be paired with good understanding of C alignment and padding
rules. Plus some experimentation to figure out subtle things like
whether `long :0;` means that struct is now forced to be long-aligned
(no, it's not, turns out).
Anyways, Per's script, while not completely correct in some known
situations, doesn't show any obvious cases where this logic breaks, so
this is a nice improvement over the previous state of this logic.
Some selftests had to be adjusted to accommodate better use of natural
alignment rules, eliminating some unnecessary padding, or changing it to
`type: 0;` alignment markers.
Note also that for when we are in between bitfields, we emit explicit
bit size, while otherwise we use `: 0`, this feels much more natural in
practice.
Next patch will add few more test cases, found through randomized Per's
script.
[0] https://lore.kernel.org/bpf/85f83c333f5355c8ac026f835b18d15060725fcb.camel@ericsson.com/
Reported-by: Per Sundström XP <per.xp.sundstrom@ericsson.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20221212211505.558851-6-andrii@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 9e3d9ae52b upstream.
It is possible to trigger these VTU violation messages very easily,
it's only necessary to send packets with an unknown VLAN ID to a port
that belongs to a VLAN-aware bridge.
Do a similar thing as for ATU violation messages, and hide them in the
kernel's trace buffer.
New usage model:
$ trace-cmd list | grep mv88e6xxx
mv88e6xxx
mv88e6xxx:mv88e6xxx_vtu_miss_violation
mv88e6xxx:mv88e6xxx_vtu_member_violation
$ trace-cmd report
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Saeed Mahameed <saeed@kernel.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Cc: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8646384d80 upstream.
In applications where the switch ports must perform 802.1X based
authentication and are therefore locked, ATU violation interrupts are
quite to be expected as part of normal operation. The problem is that
they currently spam the kernel log, even if rate limited.
Create a series of trace points, all derived from the same event class,
which log these violations to the kernel's trace buffer, which is both
much faster and much easier to ignore than printing to a serial console.
New usage model:
$ trace-cmd list | grep mv88e6xxx
mv88e6xxx
mv88e6xxx:mv88e6xxx_atu_full_violation
mv88e6xxx:mv88e6xxx_atu_miss_violation
mv88e6xxx:mv88e6xxx_atu_member_violation
$ trace-cmd record -e mv88e6xxx sleep 10
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Saeed Mahameed <saeed@kernel.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Cc: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4bf24ad09b upstream.
When an ATU violation occurs, the switch uses the ATU FID register to
report the FID of the MAC address that incurred the violation. It would
be good for the driver to know the FID value for purposes such as
logging and CPU-based authentication.
Up until now, the driver has been calling the mv88e6xxx_g1_atu_op()
function to read ATU violations, but that doesn't do exactly what we
want, namely it calls mv88e6xxx_g1_atu_fid_write() with FID 0.
(side note, the documentation for the ATU Get/Clear Violation command
says that writes to the ATU FID register have no effect before the
operation starts, it's only that we disregard the value that this
register provides once the operation completes)
So mv88e6xxx_g1_atu_fid_write() is not what we want, but rather
mv88e6xxx_g1_atu_fid_read(). However, the latter doesn't exist, we need
to write it.
The remainder of mv88e6xxx_g1_atu_op() except for
mv88e6xxx_g1_atu_fid_write() is still needed, namely to send a
GET_CLR_VIOLATION command to the ATU. In principle we could have still
kept calling mv88e6xxx_g1_atu_op(), but the MDIO writes to the ATU FID
register are pointless, but in the interest of doing less CPU work per
interrupt, write a new function called mv88e6xxx_g1_read_atu_violation()
and call it.
The FID will be the port default FID as set by mv88e6xxx_port_set_fid()
if the VID from the packet cannot be found in the VTU. Otherwise it is
the FID derived from the VTU entry associated with that VID.
Signed-off-by: Hans J. Schultz <netdev@kapio-technology.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Cc: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e86fc1a3a3 upstream.
We walk the userspace PTs to discover what mapping size was
used there. However, this can race against the userspace tables
being freed, and we end-up in the weeds.
Thankfully, the mm code is being generous and will IPI us when
doing so. So let's implement our part of the bargain and disable
interrupts around the walk. This ensures that nothing terrible
happens during that time.
We still need to handle the removal of the page tables before
the walk. For that, allow get_user_mapping_size() to return an
error, and make sure this error can be propagated all the way
to the the exit handler.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20230316174546.3777507-2-maz@kernel.org
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9228b26194 upstream.
Have KVM_GET_ONE_REG for vPMU counter (vPMC) registers (PMCCNTR_EL0
and PMEVCNTR<n>_EL0) return the sum of the register value in the sysreg
file and the current perf event counter value.
Values of vPMC registers are saved in sysreg files on certain occasions.
These saved values don't represent the current values of the vPMC
registers if the perf events for the vPMCs count events after the save.
The current values of those registers are the sum of the sysreg file
value and the current perf event counter value. But, when userspace
reads those registers (using KVM_GET_ONE_REG), KVM returns the sysreg
file value to userspace (not the sum value).
Fix this to return the sum value for KVM_GET_ONE_REG.
Fixes: 051ff581ce ("arm64: KVM: Add access handler for event counter register")
Cc: stable@vger.kernel.org
Reviewed-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Reiji Watanabe <reijiw@google.com>
Link: https://lore.kernel.org/r/20230313033208.1475499-1-reijiw@google.com
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a8e03e00b6 upstream.
SKL/GLK CSC unit suffers from a nasty issue where a CSC
coeff/offset register read or write between DC5 exit and
PSR exit will undo the CSC arming performed by DMC, and
then during PSR exit the hardware will latch zeroes into
the active CSC registers. This causes any plane going
through the CSC to output all black.
We can sidestep the issue by making sure the PSR exit has
already actually happened before we touch the CSC coeff/offset
registers. Easiest way to guarantee that is to just move the
CSC programming back into the .color_commir_arm() as we force
a PSR exit (and crucially wait for it to actually happen)
prior to touching the arming registers.
When PSR (and thus also DC states) are disabled we don't
have anything to worry about, so we can keep using the
more optional _noarm() hook for writing the CSC registers.
Cc: <stable@vger.kernel.org> #v5.19+
Cc: Manasi Navare <navaremanasi@google.com>
Cc: Drew Davenport <ddavenport@chromium.org>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Jouni Högander <jouni.hogander@intel.com>
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/8283
Fixes: d13dde4495 ("drm/i915: Split pipe+output CSC programming to noarm+arm pair")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230320095438.17328-3-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
(cherry picked from commit 80a892a4c2)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a2b6e99d8a upstream.
Keeping DC states enabled is incompatible with the _noarm()/_arm()
split we use for writing pipe/plane registers. When DC5 and PSR
are enabled, all pipe/plane registers effectively become self-arming
on account of DC5 exit arming the update, and PSR exit latching it.
What probably saves us most of the time is that (with PIPE_MISC[21]=0)
all pipe register writes themselves trigger PSR exit, and then
we don't re-enter PSR until the idle frame count has elapsed.
So it may be that the PSR exit happens already before we've
updated the state too much.
Also the PSR1 panel (at least on this KBL) seems to discard the first
frame we trasmit, presumably still scanning out from its internal
framebuffer at that point. So only the second frame we transmit is
actually visible. But I suppose that could also be panel specific
behaviour. I haven't checked out how other PSR panels behave, nor
did I bother to check what the eDP spec has to say about this.
And since this really is all about DC states, let's switch from
the MODESET domain to the DC_OFF domain. Functionally they are
100% identical. We should probably remove the MODESET domain...
And for good measure let's toss in an assert to the place where
we do the _noarm() register writes to make sure DC states are
in fact off.
v2: Just use intel_display_power_is_enabled() (Imre)
Cc: <stable@vger.kernel.org> #v5.17+
Cc: Manasi Navare <navaremanasi@google.com>
Cc: Drew Davenport <ddavenport@chromium.org>
Cc: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Fixes: d13dde4495 ("drm/i915: Split pipe+output CSC programming to noarm+arm pair")
Fixes: f8a005eb89 ("drm/i915: Optimize icl+ universal plane programming")
Fixes: 890b6ec4a5 ("drm/i915: Split skl+ plane update into noarm+arm pair")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230320183532.17727-1-ville.syrjala@linux.intel.com
(cherry picked from commit 41b4c7fe72)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
