commit a86caa9ba5 upstream.
Sven Eckelmann reported an issue with the current IPQ4019 pinctrl.
Setting up any gpio-hog in the device-tree for his device would
"kill the bootup completely":
| [ 0.477838] msm_serial 78af000.serial: could not find pctldev for node /soc/pinctrl@1000000/serial_pinmux, deferring probe
| [ 0.499828] spi_qup 78b5000.spi: could not find pctldev for node /soc/pinctrl@1000000/spi_0_pinmux, deferring probe
| [ 1.298883] requesting hog GPIO enable USB2 power (chip 1000000.pinctrl, offset 58) failed, -517
| [ 1.299609] gpiochip_add_data: GPIOs 0..99 (1000000.pinctrl) failed to register
| [ 1.308589] ipq4019-pinctrl 1000000.pinctrl: Failed register gpiochip
| [ 1.316586] msm_serial 78af000.serial: could not find pctldev for node /soc/pinctrl@1000000/serial_pinmux, deferring probe
| [ 1.322415] spi_qup 78b5000.spi: could not find pctldev for node /soc/pinctrl@1000000/spi_0_pinmux, deferri
This was also verified on a RT-AC58U (IPQ4018) which would
no longer boot, if a gpio-hog was specified. (Tried forcing
the USB LED PIN (GPIO0) to high.).
The problem is that Pinctrl+GPIO registration is currently
peformed in the following order in pinctrl-msm.c:
1. pinctrl_register()
2. gpiochip_add()
3. gpiochip_add_pin_range()
The actual error code -517 == -EPROBE_DEFER is coming from
pinctrl_get_device_gpio_range(), which is called through:
gpiochip_add
of_gpiochip_add
of_gpiochip_scan_gpios
gpiod_hog
gpiochip_request_own_desc
__gpiod_request
chip->request
gpiochip_generic_request
pinctrl_gpio_request
pinctrl_get_device_gpio_range
pinctrl_get_device_gpio_range() is unable to find any valid
pin ranges, since nothing has been added to the pinctrldev_list yet.
so the range can't be found, and the operation fails with -EPROBE_DEFER.
This patch fixes the issue by adding the "gpio-ranges" property to
the pinctrl device node of all upstream Qcom SoC. The pin ranges are
then added by the gpio core.
In order to remain compatible with older, existing DTs (and ACPI)
a check for the "gpio-ranges" property has been added to
msm_gpio_init(). This prevents the driver of adding the same entry
to the pinctrldev_list twice.
Reported-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Tested-by: Sven Eckelmann <sven.eckelmann@openmesh.com> [ipq4019]
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Amit Pundir <amit.pundir@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b432414b99 ]
If you look at "pinconf-groups" in debugfs for ssbi-gpio you'll notice
it looks like nonsense.
The problem is fairly well described in commit 1cf86bc212 ("pinctrl:
qcom: spmi-gpio: Fix pmic_gpio_config_get() to be compliant") and
commit 05e0c82895 ("pinctrl: msm: Fix msm_config_group_get() to be
compliant"), but it was pointed out that ssbi-gpio has the same
problem. Let's fix it there too.
Fixes: b4c45fe974 ("pinctrl: qcom: ssbi: Family A gpio & mpp drivers")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0d5b476f8f ]
If you look at "pinconf-groups" in debugfs for ssbi-mpp you'll notice
it looks like nonsense.
The problem is fairly well described in commit 1cf86bc212 ("pinctrl:
qcom: spmi-gpio: Fix pmic_gpio_config_get() to be compliant") and
commit 05e0c82895 ("pinctrl: msm: Fix msm_config_group_get() to be
compliant"), but it was pointed out that ssbi-mpp has the same
problem. Let's fix it there too.
NOTE: in case it's helpful to someone reading this, the way to tell
whether to do the -EINVAL or not is to look at the PCONFDUMP for a
given attribute. If the last element (has_arg) is false then you need
to do the -EINVAL trick.
ALSO NOTE: it seems unlikely that the values returned when we try to
get PIN_CONFIG_BIAS_PULL_UP will actually be printed since "has_arg"
is false for that one, but I guess it's still fine to return different
values so I kept doing that. It seems like another driver (ssbi-gpio)
uses a custom attribute (PM8XXX_QCOM_PULL_UP_STRENGTH) for something
similar so maybe a future change should do that here too.
Fixes: cfb24f6ebd ("pinctrl: Qualcomm SPMI PMIC MPP pin controller driver")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 89c68b102f ]
It looks like we parse the drive strength setting here, but never
actually write it into the hardware to update it. Parse the setting and
then write it at the end of the pinconf setting function so that it
actually sticks in the hardware.
Fixes: 0e948042c4 ("pinctrl: qcom: spmi-mpp: Implement support for sink mode")
Cc: Doug Anderson <dianders@chromium.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1cf86bc212 ]
If you do this on an sdm845 board:
grep "" /sys/kernel/debug/pinctrl/*spmi:pmic*/pinconf-groups
...it looks like nonsense. For every pin you see listed:
input bias disabled, input bias high impedance, input bias pull down, input bias pull up, ...
That's because pmic_gpio_config_get() isn't complying with the rules
that pinconf_generic_dump_one() expects. Specifically for boolean
parameters (anything with a "struct pin_config_item" where has_arg is
false) the function expects that the function should return its value
not through the "config" parameter but should return "0" if the value
is set and "-EINVAL" if the value isn't set.
Let's fix this.
>From a quick sample of other pinctrl drivers, it appears to be
tradition to also return 1 through the config parameter for these
boolean parameters when they exist. I'm not one to knock tradition,
so I'll follow tradition and return 1 in these cases. While I'm at
it, I'll also continue searching for four leaf clovers, kocking on
wood three times, and trying not to break mirrors.
NOTE: This also fixes an apparent typo for reading
PIN_CONFIG_BIAS_DISABLE where the old driver was accidentally
using "=" instead of "==" and thus was setting some internal
state when you tried to query PIN_CONFIG_BIAS_DISABLE. Oops.
Fixes: eadff30244 ("pinctrl: Qualcomm SPMI PMIC GPIO pin controller driver")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The drivers don't really need to know which PMIC they're for, so
make a generic binding for them. This alleviates us from updating
the drivers every time a new PMIC comes out. It's still
recommended that we update the binding with new PMIC models and
always specify the specific model for the MPPs and gpios before
the generic compatible string in devicetree, but this at least
cuts down on adding more and more compatible strings to the
drivers until we actually need them.
Cc: <devicetree@vger.kernel.org>
Acked-by: "Ivan T. Ivanov" <iivanov.xz@gmail.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
After some digging around I found documentation (!) of the APQ8060
EBI2 pin groups. It turns out I first need to split the group in
two: ebi2cs and ebi2 proper. The chip select pins are kind of
orthogonal to the other EBI2 pins since CS1B and CS2B can be muxed
over address bits 7 and 6 (don't know why, but they can). This
is good to fix up before we add users.
Also found what the "holes" in the assignment all the way up to
gpio158 was actually for.
All mux documentation comes from "Snapdragon(TM) S3 APQ8060-based
DragonBoard(TM) GPIO User Guide Rev. E August 10, 2012", published
by Bsquare Corporation.
As the documentation seems a bit hard to come by I put some comments
in the group definitions so that it is clear to all readers what
is going on here and what the lines are used for.
Cc: Björn Andersson <bjorn.andersson@linaro.org>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Reviewed-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add support to mux in the second external bus interface as
follows:
- CS1 and CS2 on GPIO39 and GPIO40 as func 2
- ADDR_7 thru ADDR_0 on GPIO123 thru GPIO130 as func 1
- CS4, CS3 and CS0 on GPIO132, GPIO133, GPIO134 as func 1
- DATA_15 thru DATA_0 on GPIO135 thru GPIO150 as func 1
- OE on GPIO151 as func 1
- ADV on GPIO153 as func 1
- WE on GPIO157 as func 1
This external bus is used on the APQ8060 Dragonboard to connect
an external SMSC9211 ethernet adapter, but there are many other
usecases for the EBI2.
Cc: Stephen Boyd <sboyd@codeaurora.org>
Reviewed-by: Björn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The msm8974 pinctrl variant has a couple USB HSIC "glue"
registers that let us mux between the pinctrl register settings
or the HSIC core settings for the HSIC pins (gpio 144 and gpio
145). Support this method of operation by adding hsic_data and
hsic_strobe pins that can select between hsic_ctl and gpio
functions. This allows us to toggle the hsic pin configuration
over to the HSIC core at runtime.
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The function selection bitfield is not always 3 bits wide.
Sometimes it is 4 bits wide. Let's use the npins struct member to
determine how many bits wide the function selection bitfield is
so we clear the correct amount of bits in the register while
remuxing the pins.
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In order to support the Qualcomm MDM9615 SoC, add support for the TLMM
using the Qualcomm pinctrl generic driver.
Note: the pinctrl is partial, need Documentation to complete all the groups.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Pull pin control updates from Linus Walleij:
"This kernel cycle was quite calm when it comes to pin control and
there is really just one major change, and that is the introduction of
devm_pinctrl_register() managed resources.
Apart from that linear development, details below.
Core changes:
- Add the devm_pinctrl_register() API and switch all applicable
drivers to use it, saving lots of lines of code all over the place.
New drivers:
- driver for the Broadcom NS2 SoC
- subdriver for the PXA25x SoCs
- subdriver for the AMLogic Meson GXBB SoC
Driver improvements:
- the Intel Baytrail driver now properly supports pin control
- Nomadik, Rockchip, Broadcom BCM2835 support the .get_direction()
callback in the GPIO portions
- continued development and stabilization of several SH-PFC SoC
subdrivers: r8a7795, r8a7790, r8a7794 etc"
* tag 'pinctrl-v4.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (85 commits)
Revert "pinctrl: tegra: avoid parked_reg and parked_bank"
pinctrl: meson: Fix eth_tx_en bit index
pinctrl: tegra: avoid parked_reg and parked_bank
pinctrl: tegra: Correctly check the supported configuration
pinctrl: amlogic: Add support for Amlogic Meson GXBB SoC
pinctrl: rockchip: fix pull setting error for rk3399
pinctrl: stm32: Implement .pin_config_dbg_show()
pinctrl: nomadik: hide nmk_gpio_get_mode when unused
pinctrl: ns2: rename pinctrl_utils_dt_free_map
pinctrl: at91: Merge clk_prepare and clk_enable into clk_prepare_enable
pinctrl: at91: Make at91_gpio_template const
pinctrl: baytrail: fix some error handling in debugfs
pinctrl: ns2: add pinmux driver support for Broadcom NS2 SoC
pinctrl: sirf/atlas7: trivial fix of spelling mistake on flagged
pinctrl: sh-pfc: Kill unused variable in sh_pfc_remove()
pinctrl: nomadik: implement .get_direction()
pinctrl: nomadik: use BIT() with offsets consequently
pinctrl: exynos5440: Use off-stack memory for pinctrl_gpio_range
pinctrl: zynq: Use devm_pinctrl_register() for pinctrl registration
pinctrl: u300: Use devm_pinctrl_register() for pinctrl registration
...
Rename pinctrl_utils_dt_free_map to pinctrl_utils_free_map, since
it does not depend on device tree despite the current name. This
will enforce a consistent naming in pinctr-utils.c and will make
it clear it can be called from outside device tree (e.g. from
ACPI handling code).
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Pull GPIO updates from Linus Walleij:
"Here is the bulk of GPIO changes for v4.5.
Notably there are big refactorings mostly by myself, aimed at getting
the gpio_chip into a shape that makes me believe I can proceed to
preserve state for a proper userspace ABI (character device) that has
already been proposed once, but resulted in the feedback that I need
to go back and restructure stuff. So I've been restructuring stuff.
On the way I ran into brokenness (return code from the get_value()
callback) and had to fix it. Also, refactored generic GPIO to be
simpler.
Some of that is still waiting to trickle down from the subsystems all
over the kernel that provide random gpio_chips, I've touched every
single GPIO driver in the kernel now, oh man I didn't know I was
responsible for so much...
Apart from that we're churning along as usual.
I took some effort to test and retest so it should merge nicely and we
shook out a couple of bugs in -next.
Infrastructural changes:
- In struct gpio_chip, rename the .dev node to .parent to better
reflect the fact that this is not the GPIO struct device
abstraction. We will add that soon so this would be totallt
confusing.
- It was noted that the driver .get_value() callbacks was sometimes
reporting negative -ERR values to the gpiolib core, expecting them
to be propagated to consumer gpiod_get_value() and gpio_get_value()
calls. This was not happening, so as there was a mess of drivers
returning negative errors and some returning "anything else than
zero" to indicate that a line was active. As some would have bit
31 set to indicate "line active" it clashed with negative error
codes. This is fixed by the largeish series clamping values in all
drivers with !!value to [0,1] and then augmenting the code to
propagate error codes to consumers. (Includes some ACKed patches
in other subsystems.)
- Add a void *data pointer to struct gpio_chip. The container_of()
design pattern is indeed very nice, but we want to reform the
struct gpio_chip to be a non-volative, stateless business, and keep
states internal to the gpiolib to be able to hold on to the state
when adding a proper userspace ABI (character device) further down
the road. To achieve this, drivers need a handle at the internal
state that is not dependent on their struct gpio_chip() so we add
gpiochip_add_data() and gpiochip_get_data() following the pattern
of many other subsystems. All the "use gpiochip data pointer"
patches transforms drivers to this scheme.
- The Generic GPIO chip header has been merged into the general
<linux/gpio/driver.h> header, and the custom header for that
removed. Instead of having a separate mm_gpio_chip struct for
these generic drivers, merge that into struct gpio_chip,
simplifying the code and removing the need for separate and
confusing includes.
Misc improvements:
- Stabilize the way GPIOs are looked up from the ACPI legacy
specification.
- Incremental driver features for PXA, PCA953X, Lantiq (patches from
the OpenWRT community), RCAR, Zynq, PL061, 104-idi-48
New drivers:
- Add a GPIO chip to the ALSA SoC AC97 driver.
- Add a new Broadcom NSP SoC driver (this lands in the pinctrl dir,
but the branch is merged here too to account for infrastructural
changes).
- The sx150x driver now supports the sx1502"
* tag 'gpio-v4.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (220 commits)
gpio: generic: make bgpio_pdata always visible
gpiolib: fix chip order in gpio list
gpio: mpc8xxx: Do not use gpiochip_get_data() in mpc8xxx_gpio_save_regs()
gpio: mm-lantiq: Do not use gpiochip_get_data() in ltq_mm_save_regs()
gpio: brcmstb: Allow building driver for BMIPS_GENERIC
gpio: brcmstb: Set endian flags for big-endian MIPS
gpio: moxart: fix build regression
gpio: xilinx: Do not use gpiochip_get_data() in xgpio_save_regs()
leds: pca9532: use gpiochip data pointer
leds: tca6507: use gpiochip data pointer
hid: cp2112: use gpiochip data pointer
bcma: gpio: use gpiochip data pointer
avr32: gpio: use gpiochip data pointer
video: fbdev: via: use gpiochip data pointer
gpio: pch: Optimize pch_gpio_get()
Revert "pinctrl: lantiq: Implement gpio_chip.to_irq"
pinctrl: nsp-gpio: use gpiochip data pointer
pinctrl: vt8500-wmt: use gpiochip data pointer
pinctrl: exynos5440: use gpiochip data pointer
pinctrl: at91-pio4: use gpiochip data pointer
...
of_irq_count() is not an exported symbol (and it shouldn't be
used by platform drivers anyway) so use platform_irq_count()
instead. This allows us to make the qcom pinctrl drivers modular
again.
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Andy Gross <andy.gross@linaro.org>
Cc: Bjorn Andersson <bjorn@kryo.se>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Björn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Björn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This fixes up:
commit 464231fb1f
"pinctrl: ssbi-gpio: Be sure to clamp return value"
commit b9164f0493
"gpio: ssbi-mpp: Be sure to clamp return value"
as I managed to screw up some of the logic when clamping
the return values.
Cc: Björn Andersson <bjorn@kryo.se>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.
This code was also double-inverting a bool which makes no sense
so I removed that code and moved clamping toward the end.
Cc: Björn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.
Also, this code was double-inverting a bool. That makes no
sense whatsoever, so I removed the double-invert.
Cc: Björn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.
Cc: Björn Andersson <bjorn.andersson@sonymobile.com>
Cc: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.
Cc: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Cc: Björn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
commit ab4256cfea
"pinctrl: qcom: pmic-gpio/mpp: of_irq_count() == npins"
made the Qualcomm PMIC pin control drivers make use of
of_irq_count() which is not an exported function, making
modular builds fail.
Fix this by marking the drivers as compiled-in/bool.
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Andy Gross <andy.gross@linaro.org>
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add initial pinctrl driver to support pin configuration with
pinctrl framework for msm8996.
Cc: <devicetree@vger.kernel.org>
Signed-off-by: Joonwoo Park <joonwoop@codeaurora.org>
[sboyd@codeaurora.org: Remove duplicate entries and enums]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Björn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The number of interrupts is always equal to the number of pins
provided by the PMIC gpio and MPP hardware blocks. Count the
number of irqs to figure out the number of pins instead of adding
more compatible strings or doing math on the reg property. This
should make the code more generic and ease the number of changes
we have to make to the driver for each new pmic revision.
Cc: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Reviewed-by: Andy Gross <agross@codeaurora.org>
Reviewed-by: Björn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The driver doesn't report an error message if the ACPI tables are missing
the num-gpios property (which indicates how many GPIOs there are on this
SOC), and it didn't check to ensure that the mallocs didn't fail.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Reviewed-by: Björn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
