commit b6da197a2e upstream.
As reported by Guilherme G. Piccoli:
---8<---8<---8<---
The rtc-cmos interrupt setting was changed in the commit 079062b28f
("rtc: cmos: prevent kernel warning on IRQ flags mismatch") in order
to allow shared interrupts; according to that commit's description,
some machine got kernel warnings due to the interrupt line being shared
between rtc-cmos and other hardware, and rtc-cmos didn't allow IRQ sharing
that time.
After the aforementioned commit though it was observed a huge increase
in lost HPET interrupts in some systems, observed through the following
kernel message:
[...] hpet1: lost 35 rtc interrupts
After investigation, it was narrowed down to the shared interrupts
usage when having the kernel option "irqpoll" enabled. In this case,
all IRQ handlers are called for non-timer interrupts, if such handlers
are setup in shared IRQ lines. The rtc-cmos IRQ handler could be set to
hpet_rtc_interrupt(), which will produce the kernel "lost interrupts"
message after doing work - lots of readl/writel to HPET registers, which
are known to be slow.
Although "irqpoll" is not a default kernel option, it's used in some contexts,
one being the kdump kernel (which is an already "impaired" kernel usually
running with 1 CPU available), so the performance burden could be considerable.
Also, the same issue would happen (in a shorter extent though) when using
"irqfixup" kernel option.
In a quick experiment, a virtual machine with uptime of 2 minutes produced
>300 calls to hpet_rtc_interrupt() when "irqpoll" was set, whereas without
sharing interrupts this number reduced to 1 interrupt. Machines with more
hardware than a VM should generate even more unnecessary HPET interrupts
in this scenario.
---8<---8<---8<---
After looking into the rtc-cmos driver history and DSDT table from
the Microsoft Surface 3, we may notice that Hans de Goede submitted
a correct fix (see dependency below). Thus, we simply revert
the culprit commit.
Fixes: 079062b28f ("rtc: cmos: prevent kernel warning on IRQ flags mismatch")
Depends-on: a1e23a42f1 ("rtc: cmos: Do not assume irq 8 for rtc when there are no legacy irqs")
Reported-by: Guilherme G. Piccoli <gpiccoli@canonical.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Guilherme G. Piccoli <gpiccoli@canonical.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20200123131437.28157-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3572e8aea3 ]
Besides the alarm, the PCF8563 also has a timer triggered interrupt.
In cases where the previous system left the timer and interrupts on,
or somehow the bits got enabled, the interrupt would keep triggering
as the kernel doesn't know about it.
Clear both the alarm and timer event flags, and disable the interrupts,
before requesting the interrupt line.
Fixes: ede3e9d47c ("drivers/rtc/rtc-pcf8563.c: add alarm support")
Fixes: a45d528aab ("rtc: pcf8563: clear expired alarm at boot time")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e422808860 ]
Shifting a u8 by 24 will cause the value to be promoted to an integer. If
the top bit of the u8 is set then the following conversion to an unsigned
long will sign extend the value causing the upper 32 bits to be set in
the result.
Fix this by casting the u8 value to an unsigned long before the shift.
Detected by CoverityScan, CID#1309693 ("Unintended sign extension")
Fixes: 9a9a54ad7a ("drivers/rtc: add support for Qualcomm PMIC8xxx RTC")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fb0b322537 ]
Shifting a u8 by 24 will cause the value to be promoted to an integer. If
the top bit of the u8 is set then the following conversion to an unsigned
long will sign extend the value causing the upper 32 bits to be set in
the result.
Fix this by casting the u8 value to an unsigned long before the shift.
Detected by CoverityScan, CID#714646-714649 ("Unintended sign extension")
Fixes: 2985c29c19 ("rtc: Add rtc support to 88PM80X PMIC")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dc9e471606 ]
Shifting a u8 by 24 will cause the value to be promoted to an integer. If
the top bit of the u8 is set then the following conversion to an unsigned
long will sign extend the value causing the upper 32 bits to be set in
the result.
Fix this by casting the u8 value to an unsigned long before the shift.
Detected by CoverityScan, CID#144925-144928 ("Unintended sign extension")
Fixes: 008b30408c ("mfd: Add rtc support to 88pm860x")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f0c04c2767 ]
Shifting a u8 by 24 will cause the value to be promoted to an integer. If
the top bit of the u8 is set then the following conversion to an unsigned
long will sign extend the value causing the upper 32 bits to be set in
the result.
Fix this by casting the u8 value to an unsigned long before the shift.
Detected by CoverityScan, CID#138801 ("Unintended sign extension")
Fixes: edf1aaa31f ("[PATCH] RTC subsystem: DS1672 driver")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 41ef387820 ]
In case of error, we return 0.
This is spurious and not consistent with the other functions of the driver.
Propagate the error code instead.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ef0f02fd69 ]
Clang warns:
drivers/rtc/rtc-s35390a.c:124:27: warning: implicit conversion from
'int' to 'char' changes value from 192 to -64 [-Wconstant-conversion]
buf = S35390A_FLAG_RESET | S35390A_FLAG_24H;
~ ~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~~~~~~
1 warning generated.
Update buf to be an unsigned 8-bit integer, which matches the buf member
in struct i2c_msg.
https://github.com/ClangBuiltLinux/linux/issues/145
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 189927e719 ]
Add support for specifying the xtal load capacitance in the DT node.
The pcf8523 supports xtal load capacitance of 7pF or 12.5pF.
If the rtc has the wrong configuration the time will
drift several hours/week.
The driver use the default value 12.5pF.
The DT may specify either 7000fF or 12500fF.
(The DT uses femto Farad to avoid decimal numbers).
Other values are warned and the driver uses the default value.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit ecb4a353d3 upstream.
The RTC_VL_READ ioctl reports the low battery condition. Still,
pcf8523_rtc_read_time() happily returns invalid dates in this case.
Check the battery health on pcf8523_rtc_read_time() to avoid that.
Reported-by: Erik Čuk <erik.cuk@domel.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f22b1ba15e ]
The device's remove() attempts to shut down the delayed_work scheduled
on the kernel-global workqueue by calling flush_scheduled_work().
Unfortunately, flush_scheduled_work() does not prevent the delayed_work
from re-scheduling itself. The delayed_work might run after the device
has been removed, and touch the already de-allocated info structure.
This is a potential use-after-free.
Fix by calling cancel_delayed_work_sync() during remove(): this ensures
that the delayed work is properly cancelled, is no longer running, and
is not able to re-schedule itself.
This issue was detected with the help of Coccinelle.
Signed-off-by: Sven Van Asbroeck <TheSven73@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 15d82d2249 ]
When no alarm has been programmed on RSK-RZA1, an error message is
printed during boot:
rtc rtc0: invalid alarm value: 2019-03-14T255:255:255
sh_rtc_read_alarm_value() returns 0xff when querying a hardware alarm
field that is not enabled. __rtc_read_alarm() validates the received
alarm values, and fills in missing fields when needed.
While 0xff is handled fine for the year, month, and day fields, and
corrected as considered being out-of-range, this is not the case for the
hour, minute, and second fields, where -1 is expected for missing
fields.
Fix this by returning -1 instead, as this value is handled fine for all
fields.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 36d46cdb43 upstream.
If we convert one large time values to rtc_time, in the original formula
'days * 86400' can be overflowed in 'unsigned int' type to make the formula
get one incorrect remain seconds value. Thus we can use div_s64_rem()
function to avoid this situation.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3cc9ffbb1f upstream.
Add the missing adjustment of the month range on alarm reads from the
RTC, correcting an issue coming from commit 9c6dfed92c ("rtc: m41t80:
add alarm functionality"). The range is 1-12 for hardware and 0-11 for
`struct rtc_time', and is already correctly handled on alarm writes to
the RTC.
It was correct up until commit 48e9766726 ("drivers/rtc/rtc-m41t80.c:
remove disabled alarm functionality") too, which removed the previous
implementation of alarm support.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Fixes: 9c6dfed92c ("rtc: m41t80: add alarm functionality")
References: 48e9766726 ("drivers/rtc/rtc-m41t80.c: remove disabled alarm functionality")
Cc: stable@vger.kernel.org # 4.7+
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit cd7f3a249d ]
In order to read correctly from asynchronously updated RTC registers,
it's necessary to read repeatedly until their values do not change from
read to read. It's also necessary to wait for three RTC clock ticks for
certain operations. There are no timeouts in this code and these
operations could possibly loop forever.
To avoid kernel hangs, put in timeouts.
The iMX7d can be configured to stop the SRTC on a tamper event, which
will lockup the kernel inside this driver as described above.
These hangs can happen when running under qemu, which doesn't emulate
the SNVS RTC, though currently the driver will refuse to load on qemu
due to a timeout in the driver probe method.
It could also happen if the SRTC block where somehow placed into reset
or the slow speed clock that drives the SRTC counter (but not the CPU)
were to stop.
The symptoms on a two core iMX7d are a work queue hang on
rtc_timer_do_work(), which eventually blocks a systemd fsnotify
operation that triggers a work queue flush, causing systemd to hang and
thus causing all services that should be started by systemd, like a
console getty, to fail to start or stop.
Also optimize the wait code to wait less. It only needs to wait for the
clock to advance three ticks, not to see it change three times.
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7bb633b1a9 ]
The clear of the LPTA_EN flag should be synced before writing to the
alarm register. Omitting this synchronization creates a race when
trying to change existing alarm.
Signed-off-by: Guy Shapiro <guy.shapiro@mobi-wize.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 7ce9a992ff upstream.
Fix an issue with the 32-bit range error path in `rtc_hctosys' where no
error code is set and consequently the successful preceding call result
from `rtc_read_time' is propagated to `rtc_hctosys_ret'. This in turn
makes any subsequent call to `hctosys_show' incorrectly report in sysfs
that the system time has been set from this RTC while it has not.
Set the error to ERANGE then if we can't express the result due to an
overflow.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Fixes: b3a5ac42ab ("rtc: hctosys: Ensure system time doesn't overflow time_t")
Cc: stable@vger.kernel.org # 4.17+
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit abfdff44bc ]
When using RTC_ALM_SET or RTC_WKALM_SET with rtc_wkalrm.enabled not set,
rtc_timer_enqueue() is not called and rtc_set_alarm() may succeed but the
subsequent RTC_AIE_ON ioctl will fail. RTC_ALM_READ would also fail in that
case.
Ensure rtc_set_alarm() fails when alarms are not supported to avoid letting
programs think the alarms are working for a particular RTC when they are
not.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Changes in 4.9.103
net/mlx4_core: Fix error handling in mlx4_init_port_info.
net: test tailroom before appending to linear skb
packet: in packet_snd start writing at link layer allocation
sock_diag: fix use-after-free read in __sk_free
tcp: purge write queue in tcp_connect_init()
vmxnet3: set the DMA mask before the first DMA map operation
vmxnet3: use DMA memory barriers where required
ext2: fix a block leak
s390: add assembler macros for CPU alternatives
s390: move expoline assembler macros to a header
s390/crc32-vx: use expoline for indirect branches
s390/lib: use expoline for indirect branches
s390/ftrace: use expoline for indirect branches
s390/kernel: use expoline for indirect branches
s390: move spectre sysfs attribute code
s390: extend expoline to BC instructions
s390: use expoline thunks in the BPF JIT
scsi: libsas: defer ata device eh commands to libata
scsi: sg: allocate with __GFP_ZERO in sg_build_indirect()
scsi: zfcp: fix infinite iteration on ERP ready list
cfg80211: limit wiphy names to 128 bytes
hfsplus: stop workqueue when fill_super() failed
x86/kexec: Avoid double free_page() upon do_kexec_load() failure
usb: gadget: f_uac2: fix bFirstInterface in composite gadget
usb: dwc3: Undo PHY init if soft reset fails
usb: dwc3: omap: don't miss events during suspend/resume
usb: gadget: core: Fix use-after-free of usb_request
usb: gadget: fsl_udc_core: fix ep valid checks
usb: dwc2: Fix dwc2_hsotg_core_init_disconnected()
usb: cdc_acm: prevent race at write to acm while system resumes
USB: OHCI: Fix NULL dereference in HCDs using HCD_LOCAL_MEM
net/usb/qmi_wwan.c: Add USB id for lt4120 modem
net-usb: add qmi_wwan if on lte modem wistron neweb d18q1
Bluetooth: btusb: Add USB ID 7392:a611 for Edimax EW-7611ULB
ALSA: usb-audio: Add native DSD support for Luxman DA-06
usb: dwc3: Add SoftReset PHY synchonization delay
usb: dwc3: Update DWC_usb31 GTXFIFOSIZ reg fields
xhci: zero usb device slot_id member when disabling and freeing a xhci slot
usb: dwc2: Fix interval type issue
usb: dwc2: host: Fix transaction errors in host mode
usb: gadget: ffs: Let setup() return USB_GADGET_DELAYED_STATUS
usb: gadget: ffs: Execute copy_to_user() with USER_DS set
usb: gadget: udc: change comparison to bitshift when dealing with a mask
usb: gadget: composite: fix incorrect handling of OS desc requests
media: em28xx: USB bulk packet size fix
Bluetooth: btusb: Add device ID for RTL8822BE
staging: lustre: fix bug in osc_enter_cache_try
staging: rtl8192u: return -ENOMEM on failed allocation of priv->oldaddr
staging: lustre: lmv: correctly iput lmo_root
crypto: sunxi-ss - Add MODULE_ALIAS to sun4i-ss
scsi: fas216: fix sense buffer initialization
scsi: ufs: Enable quirk to ignore sending WRITE_SAME command
scsi: bnx2fc: Fix check in SCSI completion handler for timed out request
scsi: sym53c8xx_2: iterator underflow in sym_getsync()
scsi: mptfusion: Add bounds check in mptctl_hp_targetinfo()
scsi: qla2xxx: Avoid triggering undefined behavior in qla2x00_mbx_completion()
scsi: storvsc: Increase cmd_per_lun for higher speed devices
scsi: aacraid: fix shutdown crash when init fails
scsi: qla4xxx: skip error recovery in case of register disconnect.
scsi: mpt3sas: Do not mark fw_event workqueue as WQ_MEM_RECLAIM
scsi: sd: Keep disk read-only when re-reading partition
scsi: aacraid: Insure command thread is not recursively stopped
scsi: mvsas: fix wrong endianness of sgpio api
scsi: lpfc: Fix issue_lip if link is disabled
scsi: lpfc: Fix soft lockup in lpfc worker thread during LIP testing
scsi: lpfc: Fix frequency of Release WQE CQEs
ASoC: au1x: Fix timeout tests in au1xac97c_ac97_read()
ASoC: topology: create TLV data for dapm widgets
ASoC: samsung: i2s: Ensure the RCLK rate is properly determined
clk: rockchip: Fix wrong parent for SDMMC phase clock for rk3228
clk: Don't show the incorrect clock phase
clk: tegra: Fix pll_u rate configuration
media: cx23885: Set subdev host data to clk_freq pointer
clk: rockchip: Prevent calculating mmc phase if clock rate is zero
clk: samsung: s3c2410: Fix PLL rates
clk: samsung: exynos7: Fix PLL rates
clk: samsung: exynos5260: Fix PLL rates
clk: samsung: exynos5433: Fix PLL rates
clk: samsung: exynos5250: Fix PLL rates
clk: samsung: exynos3250: Fix PLL rates
media: dmxdev: fix error code for invalid ioctls
media: cx23885: Override 888 ImpactVCBe crystal frequency
media: s3c-camif: fix out-of-bounds array access
media: vb2: Fix videobuf2 to map correct area
media: vivid: fix incorrect capabilities for radio
media: cx25821: prevent out-of-bounds read on array card
serial: xuartps: Fix out-of-bounds access through DT alias
serial: samsung: Fix out-of-bounds access through serial port index
serial: mxs-auart: Fix out-of-bounds access through serial port index
serial: imx: Fix out-of-bounds access through serial port index
serial: fsl_lpuart: Fix out-of-bounds access through DT alias
serial: arc_uart: Fix out-of-bounds access through DT alias
serial: 8250: Don't service RX FIFO if interrupts are disabled
rtc: snvs: Fix usage of snvs_rtc_enable
rtc: hctosys: Ensure system time doesn't overflow time_t
rtc: tx4939: avoid unintended sign extension on a 24 bit shift
Linux 4.9.103
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
[ Upstream commit 347876ad47 ]
The shifting of buf[5] by 24 bits to the left will be promoted to
a 32 bit signed int and then sign-extended to an unsigned long. If
the top bit of buf[5] is set then all then all the upper bits sec
end up as also being set because of the sign-extension. Fix this by
casting buf[5] to an unsigned long before the shift.
Detected by CoverityScan, CID#1465292 ("Unintended sign extension")
Fixes: 0e1492330c ("rtc: add rtc-tx4939 driver")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b3a5ac42ab ]
On 32bit platforms, time_t is still a signed 32bit long. If it is
overflowed, userspace and the kernel cant agree on the current system time.
This causes multiple issues, in particular with systemd:
https://github.com/systemd/systemd/issues/1143
A good workaround is to simply avoid using hctosys which is something I
greatly encourage as the time is better set by userspace.
However, many distribution enable it and use systemd which is rendering the
system unusable in case the RTC holds a date after 2038 (and more so after
2106). Many drivers have workaround for this case and they should be
eliminated so there is only one place left to fix when userspace is able to
cope with dates after the 31bit overflow.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1485991c02 ]
commit 179a502f8c ("rtc: snvs: add Freescale rtc-snvs driver") introduces
the SNVS RTC driver with a function snvs_rtc_enable().
snvs_rtc_enable() can return an error on the enable path however this
driver does not currently trap that failure on the probe() path and
consequently if enabling the RTC fails we encounter a later error spinning
forever in rtc_write_sync_lp().
[ 36.093481] [<c010d630>] (__irq_svc) from [<c0c2e9ec>] (_raw_spin_unlock_irqrestore+0x34/0x44)
[ 36.102122] [<c0c2e9ec>] (_raw_spin_unlock_irqrestore) from [<c072e32c>] (regmap_read+0x4c/0x5c)
[ 36.110938] [<c072e32c>] (regmap_read) from [<c085d0f4>] (rtc_write_sync_lp+0x6c/0x98)
[ 36.118881] [<c085d0f4>] (rtc_write_sync_lp) from [<c085d160>] (snvs_rtc_alarm_irq_enable+0x40/0x4c)
[ 36.128041] [<c085d160>] (snvs_rtc_alarm_irq_enable) from [<c08567b4>] (rtc_timer_do_work+0xd8/0x1a8)
[ 36.137291] [<c08567b4>] (rtc_timer_do_work) from [<c01441b8>] (process_one_work+0x28c/0x76c)
[ 36.145840] [<c01441b8>] (process_one_work) from [<c01446cc>] (worker_thread+0x34/0x58c)
[ 36.153961] [<c01446cc>] (worker_thread) from [<c014aee4>] (kthread+0x138/0x150)
[ 36.161388] [<c014aee4>] (kthread) from [<c0107e14>] (ret_from_fork+0x14/0x20)
[ 36.168635] rcu_sched kthread starved for 2602 jiffies! g496 c495 f0x2 RCU_GP_WAIT_FQS(3) ->state=0x0 ->cpu=0
[ 36.178564] rcu_sched R running task 0 8 2 0x00000000
[ 36.185664] [<c0c288b0>] (__schedule) from [<c0c29134>] (schedule+0x3c/0xa0)
[ 36.192739] [<c0c29134>] (schedule) from [<c0c2db80>] (schedule_timeout+0x78/0x4e0)
[ 36.200422] [<c0c2db80>] (schedule_timeout) from [<c01a7ab0>] (rcu_gp_kthread+0x648/0x1864)
[ 36.208800] [<c01a7ab0>] (rcu_gp_kthread) from [<c014aee4>] (kthread+0x138/0x150)
[ 36.216309] [<c014aee4>] (kthread) from [<c0107e14>] (ret_from_fork+0x14/0x20)
This patch fixes by parsing the result of rtc_write_sync_lp() and
propagating both in the probe and elsewhere. If the RTC doesn't start we
don't proceed loading the driver and don't get into this loop mess later
on.
Fixes: 179a502f8c ("rtc: snvs: add Freescale rtc-snvs driver")
Signed-off-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Changes in 4.9.98
ext4: prevent right-shifting extents beyond EXT_MAX_BLOCKS
ext4: set h_journal if there is a failure starting a reserved handle
ext4: add validity checks for bitmap block numbers
ext4: fix bitmap position validation
random: set up the NUMA crng instances after the CRNG is fully initialized
random: fix possible sleeping allocation from irq context
random: rate limit unseeded randomness warnings
usbip: usbip_event: fix to not print kernel pointer address
usbip: usbip_host: fix to hold parent lock for device_attach() calls
usbip: vhci_hcd: Fix usb device and sockfd leaks
USB: serial: simple: add libtransistor console
USB: serial: ftdi_sio: use jtag quirk for Arrow USB Blaster
USB: serial: cp210x: add ID for NI USB serial console
usb: core: Add quirk for HP v222w 16GB Mini
USB: Increment wakeup count on remote wakeup.
ALSA: usb-audio: Skip broken EU on Dell dock USB-audio
virtio: add ability to iterate over vqs
virtio_console: free buffers after reset
drm/virtio: fix vq wait_event condition
tty: Don't call panic() at tty_ldisc_init()
tty: n_gsm: Fix long delays with control frame timeouts in ADM mode
tty: n_gsm: Fix DLCI handling for ADM mode if debug & 2 is not set
tty: Use __GFP_NOFAIL for tty_ldisc_get()
ALSA: dice: fix OUI for TC group
ALSA: dice: fix error path to destroy initialized stream data
ALSA: opl3: Hardening for potential Spectre v1
ALSA: asihpi: Hardening for potential Spectre v1
ALSA: hdspm: Hardening for potential Spectre v1
ALSA: rme9652: Hardening for potential Spectre v1
ALSA: control: Hardening for potential Spectre v1
ALSA: core: Report audio_tstamp in snd_pcm_sync_ptr
ALSA: seq: oss: Fix unbalanced use lock for synth MIDI device
ALSA: seq: oss: Hardening for potential Spectre v1
ALSA: hda: Hardening for potential Spectre v1
ALSA: hda/realtek - Add some fixes for ALC233
mtd: cfi: cmdset_0001: Do not allow read/write to suspend erase block.
mtd: cfi: cmdset_0001: Workaround Micron Erase suspend bug.
mtd: cfi: cmdset_0002: Do not allow read/write to suspend erase block.
kobject: don't use WARN for registration failures
scsi: sd: Defer spinning up drive while SANITIZE is in progress
PCI: aardvark: Fix logic in advk_pcie_{rd,wr}_conf()
PCI: aardvark: Set PIO_ADDR_LS correctly in advk_pcie_rd_conf()
PCI: aardvark: Fix PCIe Max Read Request Size setting
ARM: amba: Make driver_override output consistent with other buses
ARM: amba: Fix race condition with driver_override
ARM: amba: Don't read past the end of sysfs "driver_override" buffer
crypto: drbg - set freed buffers to NULL
ASoC: fsl_esai: Fix divisor calculation failure at lower ratio
libceph: un-backoff on tick when we have a authenticated session
libceph: reschedule a tick in finish_hunting()
libceph: validate con->state at the top of try_write()
earlycon: Use a pointer table to fix __earlycon_table stride
cpufreq: powernv: Fix hardlockup due to synchronous smp_call in timer interrupt
rtc: opal: Fix OPAL RTC driver OPAL_BUSY loops
drm/amdgpu: set COMPUTE_PGM_RSRC1 for SGPR/VGPR clearing shaders
objtool, perf: Fix GCC 8 -Wrestrict error
tools/lib/subcmd/pager.c: do not alias select() params
x86/ipc: Fix x32 version of shmid64_ds and msqid64_ds
x86/smpboot: Don't use mwait_play_dead() on AMD systems
x86/microcode/intel: Save microcode patch unconditionally
powerpc/eeh: Fix race with driver un/bind
Linux 4.9.98
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
