commit 6596a02295 upstream.
Commit 749439bfac ("ipv6: fix udpv6
sendmsg crash caused by too small MTU") breaks PMTU for xfrm.
A Packet Too Big ICMPv6 message received in response to an ESP
packet will prevent all further communication through the tunnel
if the reported MTU minus the ESP overhead is smaller than 1280.
E.g. in a case of a tunnel-mode ESP with sha256/aes the overhead
is 92 bytes. Receiving a PTB with MTU of 1371 or less will result
in all further packets in the tunnel dropped. A ping through the
tunnel fails with "ping: sendmsg: Invalid argument".
Apparently the MTU on the xfrm route is smaller than 1280 and
fails the check inside ip6_setup_cork() added by 749439bf.
We found this by debugging USGv6/ipv6ready failures. Failing
tests are: "Phase-2 Interoperability Test Scenario IPsec" /
5.3.11 and 5.4.11 (Tunnel Mode: Fragmentation).
Commit b515d26372 ("xfrm:
xfrm_state_mtu should return at least 1280 for ipv6") attempted
to fix this but caused another regression in TCP MSS calculations
and had to be reverted.
The patch below fixes the situation by dropping the MTU
check and instead checking for the underflows described in the
749439bf commit message.
Signed-off-by: Jiri Bohac <jbohac@suse.cz>
Fixes: 749439bfac ("ipv6: fix udpv6 sendmsg crash caused by too small MTU")
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cc20cced05 upstream.
We encounter a tcp drop issue in our cloud environment. Packet GROed in
host forwards to a VM virtio_net nic with net_failover enabled. VM acts
as a IPVS LB with ipip encapsulation. The full path like:
host gro -> vm virtio_net rx -> net_failover rx -> ipvs fullnat
-> ipip encap -> net_failover tx -> virtio_net tx
When net_failover transmits a ipip pkt (gso_type = 0x0103, which means
SKB_GSO_TCPV4, SKB_GSO_DODGY and SKB_GSO_IPXIP4), there is no gso
did because it supports TSO and GSO_IPXIP4. But network_header points to
inner ip header.
Call Trace:
tcp4_gso_segment ------> return NULL
inet_gso_segment ------> inner iph, network_header points to
ipip_gso_segment
inet_gso_segment ------> outer iph
skb_mac_gso_segment
Afterwards virtio_net transmits the pkt, only inner ip header is modified.
And the outer one just keeps unchanged. The pkt will be dropped in remote
host.
Call Trace:
inet_gso_segment ------> inner iph, outer iph is skipped
skb_mac_gso_segment
__skb_gso_segment
validate_xmit_skb
validate_xmit_skb_list
sch_direct_xmit
__qdisc_run
__dev_queue_xmit ------> virtio_net
dev_hard_start_xmit
__dev_queue_xmit ------> net_failover
ip_finish_output2
ip_output
iptunnel_xmit
ip_tunnel_xmit
ipip_tunnel_xmit ------> ipip
dev_hard_start_xmit
__dev_queue_xmit
ip_finish_output2
ip_output
ip_forward
ip_rcv
__netif_receive_skb_one_core
netif_receive_skb_internal
napi_gro_receive
receive_buf
virtnet_poll
net_rx_action
The root cause of this issue is specific with the rare combination of
SKB_GSO_DODGY and a tunnel device that adds an SKB_GSO_ tunnel option.
SKB_GSO_DODGY is set from external virtio_net. We need to reset network
header when callbacks.gso_segment() returns NULL.
This patch also includes ipv6_gso_segment(), considering SIT, etc.
Fixes: cb32f511a7 ("ipip: add GSO/TSO support")
Signed-off-by: Tao Liu <thomas.liu@ucloud.cn>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6cee105e7f upstream.
The warning messages can be invoked from the data path for every packet
transmitted through an ip6gre netdev, leading to high CPU utilization.
Fix that by rate limiting the messages.
Fixes: 09c6bbf090 ("[IPV6]: Do mandatory IPv6 tunnel endpoint checks in realtime")
Reported-by: Maksym Yaremchuk <maksymy@nvidia.com>
Tested-by: Maksym Yaremchuk <maksymy@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ad5d07f4a9 upstream.
The current CIPSO and CALIPSO refcounting scheme for the DOI
definitions is a bit flawed in that we:
1. Don't correctly match gets/puts in netlbl_cipsov4_list().
2. Decrement the refcount on each attempt to remove the DOI from the
DOI list, only removing it from the list once the refcount drops
to zero.
This patch fixes these problems by adding the missing "puts" to
netlbl_cipsov4_list() and introduces a more conventional, i.e.
not-buggy, refcounting mechanism to the DOI definitions. Upon the
addition of a DOI to the DOI list, it is initialized with a refcount
of one, removing a DOI from the list removes it from the list and
drops the refcount by one; "gets" and "puts" behave as expected with
respect to refcounts, increasing and decreasing the DOI's refcount by
one.
Fixes: b1edeb1023 ("netlabel: Replace protocol/NetLabel linking with refrerence counts")
Fixes: d7cce01504 ("netlabel: Add support for removing a CALIPSO DOI.")
Reported-by: syzbot+9ec037722d2603a9f52e@syzkaller.appspotmail.com
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: Backported to 4.9: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c1833c3964 ]
The "__ip6_tnl_parm" struct was left uninitialized causing an invalid
load of random data when the "__ip6_tnl_parm" struct was used elsewhere.
As an example, in the function "ip6_tnl_xmit_ctl()", it tries to access
the "collect_md" member. With "__ip6_tnl_parm" being uninitialized and
containing random data, the UBSAN detected that "collect_md" held a
non-boolean value.
The UBSAN issue is as follows:
===============================================================
UBSAN: invalid-load in net/ipv6/ip6_tunnel.c:1025:14
load of value 30 is not a valid value for type '_Bool'
CPU: 1 PID: 228 Comm: kworker/1:3 Not tainted 5.16.0-rc4+ #8
Hardware name: Red Hat KVM, BIOS 0.5.1 01/01/2011
Workqueue: ipv6_addrconf addrconf_dad_work
Call Trace:
<TASK>
dump_stack_lvl+0x44/0x57
ubsan_epilogue+0x5/0x40
__ubsan_handle_load_invalid_value+0x66/0x70
? __cpuhp_setup_state+0x1d3/0x210
ip6_tnl_xmit_ctl.cold.52+0x2c/0x6f [ip6_tunnel]
vti6_tnl_xmit+0x79c/0x1e96 [ip6_vti]
? lock_is_held_type+0xd9/0x130
? vti6_rcv+0x100/0x100 [ip6_vti]
? lock_is_held_type+0xd9/0x130
? rcu_read_lock_bh_held+0xc0/0xc0
? lock_acquired+0x262/0xb10
dev_hard_start_xmit+0x1e6/0x820
__dev_queue_xmit+0x2079/0x3340
? mark_lock.part.52+0xf7/0x1050
? netdev_core_pick_tx+0x290/0x290
? kvm_clock_read+0x14/0x30
? kvm_sched_clock_read+0x5/0x10
? sched_clock_cpu+0x15/0x200
? find_held_lock+0x3a/0x1c0
? lock_release+0x42f/0xc90
? lock_downgrade+0x6b0/0x6b0
? mark_held_locks+0xb7/0x120
? neigh_connected_output+0x31f/0x470
? lockdep_hardirqs_on+0x79/0x100
? neigh_connected_output+0x31f/0x470
? ip6_finish_output2+0x9b0/0x1d90
? rcu_read_lock_bh_held+0x62/0xc0
? ip6_finish_output2+0x9b0/0x1d90
ip6_finish_output2+0x9b0/0x1d90
? ip6_append_data+0x330/0x330
? ip6_mtu+0x166/0x370
? __ip6_finish_output+0x1ad/0xfb0
? nf_hook_slow+0xa6/0x170
ip6_output+0x1fb/0x710
? nf_hook.constprop.32+0x317/0x430
? ip6_finish_output+0x180/0x180
? __ip6_finish_output+0xfb0/0xfb0
? lock_is_held_type+0xd9/0x130
ndisc_send_skb+0xb33/0x1590
? __sk_mem_raise_allocated+0x11cf/0x1560
? dst_output+0x4a0/0x4a0
? ndisc_send_rs+0x432/0x610
addrconf_dad_completed+0x30c/0xbb0
? addrconf_rs_timer+0x650/0x650
? addrconf_dad_work+0x73c/0x10e0
addrconf_dad_work+0x73c/0x10e0
? addrconf_dad_completed+0xbb0/0xbb0
? rcu_read_lock_sched_held+0xaf/0xe0
? rcu_read_lock_bh_held+0xc0/0xc0
process_one_work+0x97b/0x1740
? pwq_dec_nr_in_flight+0x270/0x270
worker_thread+0x87/0xbf0
? process_one_work+0x1740/0x1740
kthread+0x3ac/0x490
? set_kthread_struct+0x100/0x100
ret_from_fork+0x22/0x30
</TASK>
===============================================================
The solution is to initialize "__ip6_tnl_parm" struct to zeros in the
"vti6_siocdevprivate()" function.
Signed-off-by: William Zhao <wizhao@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 310e2d43c3 ]
ip6tables only sets the `IP6T_F_PROTO` flag on a rule if a protocol is
specified (`-p tcp`, for example). However, if the flag is not set,
`ip6_packet_match` doesn't call `ipv6_find_hdr` for the skb, in which
case the fragment offset is left uninitialized and a garbage value is
passed to each matcher.
Signed-off-by: Jeremy Sowden <jeremy@azazel.net>
Reviewed-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit a9f5970767 upstream.
up->corkflag field can be read or written without any lock.
Annotate accesses to avoid possible syzbot/KCSAN reports.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c7bb4b8903 upstream.
While TCP stack scales reasonably well, there is still one part that
can be used to DDOS it.
IPv6 Packet too big messages have to lookup/insert a new route,
and if abused by attackers, can easily put hosts under high stress,
with many cpus contending on a spinlock while one is stuck in fib6_run_gc()
ip6_protocol_deliver_rcu()
icmpv6_rcv()
icmpv6_notify()
tcp_v6_err()
tcp_v6_mtu_reduced()
inet6_csk_update_pmtu()
ip6_rt_update_pmtu()
__ip6_rt_update_pmtu()
ip6_rt_cache_alloc()
ip6_dst_alloc()
dst_alloc()
ip6_dst_gc()
fib6_run_gc()
spin_lock_bh() ...
Some of our servers have been hit by malicious ICMPv6 packets
trying to _increase_ the MTU/MSS of TCP flows.
We believe these ICMPv6 packets are a result of a bug in one ISP stack,
since they were blindly sent back for _every_ (small) packet sent to them.
These packets are for one TCP flow:
09:24:36.266491 IP6 Addr1 > Victim ICMP6, packet too big, mtu 1460, length 1240
09:24:36.266509 IP6 Addr1 > Victim ICMP6, packet too big, mtu 1460, length 1240
09:24:36.316688 IP6 Addr1 > Victim ICMP6, packet too big, mtu 1460, length 1240
09:24:36.316704 IP6 Addr1 > Victim ICMP6, packet too big, mtu 1460, length 1240
09:24:36.608151 IP6 Addr1 > Victim ICMP6, packet too big, mtu 1460, length 1240
TCP stack can filter some silly requests :
1) MTU below IPV6_MIN_MTU can be filtered early in tcp_v6_err()
2) tcp_v6_mtu_reduced() can drop requests trying to increase current MSS.
This tests happen before the IPv6 routing stack is entered, thus
removing the potential contention and route exhaustion.
Note that IPv6 stack was performing these checks, but too late
(ie : after the route has been added, and after the potential
garbage collect war)
v2: fix typo caught by Martin, thanks !
v3: exports tcp_mtu_to_mss(), caught by David, thanks !
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Maciej Żenczykowski <maze@google.com>
Cc: Martin KaFai Lau <kafai@fb.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 561022acb1 upstream.
While tp->mtu_info is read while socket is owned, the write
sides happen from err handlers (tcp_v[46]_mtu_reduced)
which only own the socket spinlock.
Fixes: 563d34d057 ("tcp: dont drop MTU reduction indications")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 40fc3054b4 upstream.
Commit 628a5c5618 ("[INET]: Add IP(V6)_PMTUDISC_RPOBE") introduced
ip6_skb_dst_mtu with return value of signed int which is inconsistent
with actually returned values. Also 2 users of this function actually
assign its value to unsigned int variable and only __xfrm6_output
assigns result of this function to signed variable but actually uses
as unsigned in further comparisons and calls. Change this function
to return unsigned int value.
Fixes: 628a5c5618 ("[INET]: Add IP(V6)_PMTUDISC_RPOBE")
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Vadim Fedorenko <vfedorenko@novek.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 62f20e068c ]
This is a complement to commit aa6dd211e4 ("inet: use bigger hash
table for IP ID generation"), but focusing on some specific aspects
of IPv6.
Contary to IPv4, IPv6 only uses packet IDs with fragments, and with a
minimum MTU of 1280, it's much less easy to force a remote peer to
produce many fragments to explore its ID sequence. In addition packet
IDs are 32-bit in IPv6, which further complicates their analysis. On
the other hand, it is often easier to choose among plenty of possible
source addresses and partially work around the bigger hash table the
commit above permits, which leaves IPv6 partially exposed to some
possibilities of remote analysis at the risk of weakening some
protocols like DNS if some IDs can be predicted with a good enough
probability.
Given the wide range of permitted IDs, the risk of collision is extremely
low so there's no need to rely on the positive increment algorithm that
is shared with the IPv4 code via ip_idents_reserve(). We have a fast
PRNG, so let's simply call prandom_u32() and be done with it.
Performance measurements at 10 Gbps couldn't show any difference with
the previous code, even when using a single core, because due to the
large fragments, we're limited to only ~930 kpps at 10 Gbps and the cost
of the random generation is completely offset by other operations and by
the network transfer time. In addition, this change removes the need to
update a shared entry in the idents table so it may even end up being
slightly faster on large scale systems where this matters.
The risk of at least one collision here is about 1/80 million among
10 IDs, 1/850k among 100 IDs, and still only 1/8.5k among 1000 IDs,
which remains very low compared to IPv4 where all IDs are reused
every 4 to 80ms on a 10 Gbps flow depending on packet sizes.
Reported-by: Amit Klein <aksecurity@gmail.com>
Signed-off-by: Willy Tarreau <w@1wt.eu>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20210529110746.6796-1-w@1wt.eu
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a8b897c7bc ]
Kaustubh reported and diagnosed a panic in udp_lib_lookup().
The root cause is udp_abort() racing with close(). Both
racing functions acquire the socket lock, but udp{v6}_destroy_sock()
release it before performing destructive actions.
We can't easily extend the socket lock scope to avoid the race,
instead use the SOCK_DEAD flag to prevent udp_abort from doing
any action when the critical race happens.
Diagnosed-and-tested-by: Kaustubh Pandey <kapandey@codeaurora.org>
Fixes: 5d77dca828 ("net: diag: support SOCK_DESTROY for UDP sockets")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 020ef930b8 ]
mld_newpack() doesn't allow to allocate high order page,
only order-0 allocation is allowed.
If headroom size is too large, a kernel panic could occur in skb_put().
Test commands:
ip netns del A
ip netns del B
ip netns add A
ip netns add B
ip link add veth0 type veth peer name veth1
ip link set veth0 netns A
ip link set veth1 netns B
ip netns exec A ip link set lo up
ip netns exec A ip link set veth0 up
ip netns exec A ip -6 a a 2001:db8:0::1/64 dev veth0
ip netns exec B ip link set lo up
ip netns exec B ip link set veth1 up
ip netns exec B ip -6 a a 2001:db8:0::2/64 dev veth1
for i in {1..99}
do
let A=$i-1
ip netns exec A ip link add ip6gre$i type ip6gre \
local 2001:db8:$A::1 remote 2001:db8:$A::2 encaplimit 100
ip netns exec A ip -6 a a 2001:db8:$i::1/64 dev ip6gre$i
ip netns exec A ip link set ip6gre$i up
ip netns exec B ip link add ip6gre$i type ip6gre \
local 2001:db8:$A::2 remote 2001:db8:$A::1 encaplimit 100
ip netns exec B ip -6 a a 2001:db8:$i::2/64 dev ip6gre$i
ip netns exec B ip link set ip6gre$i up
done
Splat looks like:
kernel BUG at net/core/skbuff.c:110!
invalid opcode: 0000 [#1] SMP DEBUG_PAGEALLOC KASAN PTI
CPU: 0 PID: 7 Comm: kworker/0:1 Not tainted 5.12.0+ #891
Workqueue: ipv6_addrconf addrconf_dad_work
RIP: 0010:skb_panic+0x15d/0x15f
Code: 92 fe 4c 8b 4c 24 10 53 8b 4d 70 45 89 e0 48 c7 c7 00 ae 79 83
41 57 41 56 41 55 48 8b 54 24 a6 26 f9 ff <0f> 0b 48 8b 6c 24 20 89
34 24 e8 4a 4e 92 fe 8b 34 24 48 c7 c1 20
RSP: 0018:ffff88810091f820 EFLAGS: 00010282
RAX: 0000000000000089 RBX: ffff8881086e9000 RCX: 0000000000000000
RDX: 0000000000000089 RSI: 0000000000000008 RDI: ffffed1020123efb
RBP: ffff888005f6eac0 R08: ffffed1022fc0031 R09: ffffed1022fc0031
R10: ffff888117e00187 R11: ffffed1022fc0030 R12: 0000000000000028
R13: ffff888008284eb0 R14: 0000000000000ed8 R15: 0000000000000ec0
FS: 0000000000000000(0000) GS:ffff888117c00000(0000)
knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f8b801c5640 CR3: 0000000033c2c006 CR4: 00000000003706f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
? ip6_mc_hdr.isra.26.constprop.46+0x12a/0x600
? ip6_mc_hdr.isra.26.constprop.46+0x12a/0x600
skb_put.cold.104+0x22/0x22
ip6_mc_hdr.isra.26.constprop.46+0x12a/0x600
? rcu_read_lock_sched_held+0x91/0xc0
mld_newpack+0x398/0x8f0
? ip6_mc_hdr.isra.26.constprop.46+0x600/0x600
? lock_contended+0xc40/0xc40
add_grhead.isra.33+0x280/0x380
add_grec+0x5ca/0xff0
? mld_sendpack+0xf40/0xf40
? lock_downgrade+0x690/0x690
mld_send_initial_cr.part.34+0xb9/0x180
ipv6_mc_dad_complete+0x15d/0x1b0
addrconf_dad_completed+0x8d2/0xbb0
? lock_downgrade+0x690/0x690
? addrconf_rs_timer+0x660/0x660
? addrconf_dad_work+0x73c/0x10e0
addrconf_dad_work+0x73c/0x10e0
Allowing high order page allocation could fix this problem.
Fixes: 72e09ad107 ("ipv6: avoid high order allocations")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 0d7a7b2014 upstream.
My previous commits added a dev_hold() in tunnels ndo_init(),
but forgot to remove it from special functions setting up fallback tunnels.
Fallback tunnels do call their respective ndo_init()
This leads to various reports like :
unregister_netdevice: waiting for ip6gre0 to become free. Usage count = 2
Fixes: 48bb569726 ("ip6_tunnel: sit: proper dev_{hold|put} in ndo_[un]init methods")
Fixes: 6289a98f08 ("sit: proper dev_{hold|put} in ndo_[un]init methods")
Fixes: 40cb881b5a ("ip6_vti: proper dev_{hold|put} in ndo_[un]init methods")
Fixes: 7f700334be ("ip6_gre: proper dev_{hold|put} in ndo_[un]init methods")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6289a98f08 upstream.
After adopting CONFIG_PCPU_DEV_REFCNT=n option, syzbot was able to trigger
a warning [1]
Issue here is that:
- all dev_put() should be paired with a corresponding prior dev_hold().
- A driver doing a dev_put() in its ndo_uninit() MUST also
do a dev_hold() in its ndo_init(), only when ndo_init()
is returning 0.
Otherwise, register_netdevice() would call ndo_uninit()
in its error path and release a refcount too soon.
Fixes: 919067cc84 ("net: add CONFIG_PCPU_DEV_REFCNT")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 610f8c0fc8 upstream.
A sit interface created without a local or a remote address is linked
into the `sit_net::tunnels_wc` list of its original namespace. When
deleting a network namespace, delete the devices that have been moved.
The following script triggers a null pointer dereference if devices
linked in a deleted `sit_net` remain:
for i in `seq 1 30`; do
ip netns add ns-test
ip netns exec ns-test ip link add dev veth0 type veth peer veth1
ip netns exec ns-test ip link add dev sit$i type sit dev veth0
ip netns exec ns-test ip link set dev sit$i netns $$
ip netns del ns-test
done
for i in `seq 1 30`; do
ip link del dev sit$i
done
Fixes: 5e6700b3bf ("sit: add support of x-netns")
Signed-off-by: Hristo Venev <hristo@venev.name>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 864db232dc upstream.
nlh is being checked for validtity two times when it is dereferenced in
this function. Check for validity again when updating the flags through
nlh pointer to make the dereferencing safe.
CC: <stable@vger.kernel.org>
Addresses-Coverity: ("NULL pointer dereference")
Signed-off-by: Muhammad Usama Anjum <musamaanjum@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit dcc32f4f18 ]
This reverts commit 6af1799aaf.
Commit 6af1799aaf ("ipv6: drop incoming packets having a v4mapped
source address") introduced an input check against v4mapped addresses.
Use of such addresses on the wire is indeed questionable and not
allowed on public Internet. As the commit pointed out
https://tools.ietf.org/html/draft-itojun-v6ops-v4mapped-harmful-02
lists potential issues.
Unfortunately there are applications which use v4mapped addresses,
and breaking them is a clear regression. For example v4mapped
addresses (or any semi-valid addresses, really) may be used
for uni-direction event streams or packet export.
Since the issue which sparked the addition of the check was with
TCP and request_socks in particular push the check down to TCPv6
and DCCP. This restores the ability to receive UDPv6 packets with
v4mapped address as the source.
Keep using the IPSTATS_MIB_INHDRERRORS statistic to minimize the
user-visible changes.
Fixes: 6af1799aaf ("ipv6: drop incoming packets having a v4mapped source address")
Reported-by: Sunyi Shao <sunyishao@fb.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit ee576c47db upstream.
The icmp{,v6}_send functions make all sorts of use of skb->cb, casting
it with IPCB or IP6CB, assuming the skb to have come directly from the
inet layer. But when the packet comes from the ndo layer, especially
when forwarded, there's no telling what might be in skb->cb at that
point. As a result, the icmp sending code risks reading bogus memory
contents, which can result in nasty stack overflows such as this one
reported by a user:
panic+0x108/0x2ea
__stack_chk_fail+0x14/0x20
__icmp_send+0x5bd/0x5c0
icmp_ndo_send+0x148/0x160
In icmp_send, skb->cb is cast with IPCB and an ip_options struct is read
from it. The optlen parameter there is of particular note, as it can
induce writes beyond bounds. There are quite a few ways that can happen
in __ip_options_echo. For example:
// sptr/skb are attacker-controlled skb bytes
sptr = skb_network_header(skb);
// dptr/dopt points to stack memory allocated by __icmp_send
dptr = dopt->__data;
// sopt is the corrupt skb->cb in question
if (sopt->rr) {
optlen = sptr[sopt->rr+1]; // corrupt skb->cb + skb->data
soffset = sptr[sopt->rr+2]; // corrupt skb->cb + skb->data
// this now writes potentially attacker-controlled data, over
// flowing the stack:
memcpy(dptr, sptr+sopt->rr, optlen);
}
In the icmpv6_send case, the story is similar, but not as dire, as only
IP6CB(skb)->iif and IP6CB(skb)->dsthao are used. The dsthao case is
worse than the iif case, but it is passed to ipv6_find_tlv, which does
a bit of bounds checking on the value.
This is easy to simulate by doing a `memset(skb->cb, 0x41,
sizeof(skb->cb));` before calling icmp{,v6}_ndo_send, and it's only by
good fortune and the rarity of icmp sending from that context that we've
avoided reports like this until now. For example, in KASAN:
BUG: KASAN: stack-out-of-bounds in __ip_options_echo+0xa0e/0x12b0
Write of size 38 at addr ffff888006f1f80e by task ping/89
CPU: 2 PID: 89 Comm: ping Not tainted 5.10.0-rc7-debug+ #5
Call Trace:
dump_stack+0x9a/0xcc
print_address_description.constprop.0+0x1a/0x160
__kasan_report.cold+0x20/0x38
kasan_report+0x32/0x40
check_memory_region+0x145/0x1a0
memcpy+0x39/0x60
__ip_options_echo+0xa0e/0x12b0
__icmp_send+0x744/0x1700
Actually, out of the 4 drivers that do this, only gtp zeroed the cb for
the v4 case, while the rest did not. So this commit actually removes the
gtp-specific zeroing, while putting the code where it belongs in the
shared infrastructure of icmp{,v6}_ndo_send.
This commit fixes the issue by passing an empty IPCB or IP6CB along to
the functions that actually do the work. For the icmp_send, this was
already trivial, thanks to __icmp_send providing the plumbing function.
For icmpv6_send, this required a tiny bit of refactoring to make it
behave like the v4 case, after which it was straight forward.
Fixes: a2b78e9b2c ("sunvnet: generate ICMP PTMUD messages for smaller port MTUs")
Reported-by: SinYu <liuxyon@gmail.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Link: https://lore.kernel.org/netdev/CAF=yD-LOF116aHub6RMe8vB8ZpnrrnoTdqhobEx+bvoA8AsP0w@mail.gmail.com/T/
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Link: https://lore.kernel.org/r/20210223131858.72082-1-Jason@zx2c4.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cc7a21b6fb upstream.
If IPv6 is builtin, we do not need an expensive indirect call
to reach icmp6_send().
v2: put inline keyword before the type to avoid sparse warnings.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0b41713b60 upstream.
This introduces a helper function to be called only by network drivers
that wraps calls to icmp[v6]_send in a conntrack transformation, in case
NAT has been used. We don't want to pollute the non-driver path, though,
so we introduce this as a helper to be called by places that actually
make use of this, as suggested by Florian.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Cc: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a826b04303 upstream.
The ff00::/8 multicast route is created without specifying the fc_protocol
field, so the default RTPROT_BOOT value is used:
$ ip -6 -d route
unicast ::1 dev lo proto kernel scope global metric 256 pref medium
unicast fe80::/64 dev eth0 proto kernel scope global metric 256 pref medium
unicast ff00::/8 dev eth0 proto boot scope global metric 256 pref medium
As the documentation says, this value identifies routes installed during
boot, but the route is created when interface is set up.
Change the value to RTPROT_KERNEL which is a better value.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Matteo Croce <mcroce@microsoft.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
