[ Upstream commit fcee5ce50b ]
When firmware load failed, kernel report task hung as follows:
INFO: task xrun:5191 blocked for more than 147 seconds.
Tainted: G W 5.16.0-rc5-next-20211220+ #11
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
task:xrun state:D stack: 0 pid: 5191 ppid: 270 flags:0x00000004
Call Trace:
__schedule+0xc12/0x4b50 kernel/sched/core.c:4986
schedule+0xd7/0x260 kernel/sched/core.c:6369 (discriminator 1)
schedule_timeout+0x7aa/0xa80 kernel/time/timer.c:1857
wait_for_completion+0x181/0x290 kernel/sched/completion.c:85
lattice_ecp3_remove+0x32/0x40 drivers/misc/lattice-ecp3-config.c:221
spi_remove+0x72/0xb0 drivers/spi/spi.c:409
lattice_ecp3_remove() wait for signals from firmware loading, but when
load failed, firmware_load() does not send this signal. This cause
device remove hung. Fix it by sending signal even if load failed.
Fixes: 781551df57 ("misc: Add Lattice ECP3 FPGA configuration via SPI")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Link: https://lore.kernel.org/r/20211228125522.3122284-1-weiyongjun1@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 42641042c1 upstream.
clang-14 complains about an unusual way of converting a pointer to
an integer:
drivers/misc/cb710/sgbuf2.c:50:15: error: performing pointer subtraction with a null pointer has undefined behavior [-Werror,-Wnull-pointer-subtraction]
return ((ptr - NULL) & 3) != 0;
Replace this with a normal cast to uintptr_t.
Fixes: 5f5bac8272 ("mmc: Driver for CB710/720 memory card reader (MMC part)")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20210927121408.939246-1-arnd@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a30dc6cf0d upstream.
I got a NULL pointer dereference report when doing fuzz test:
Call Trace:
qp_release_pages+0xae/0x130
qp_host_unregister_user_memory.isra.25+0x2d/0x80
vmci_qp_broker_unmap+0x191/0x320
? vmci_host_do_alloc_queuepair.isra.9+0x1c0/0x1c0
vmci_host_unlocked_ioctl+0x59f/0xd50
? do_vfs_ioctl+0x14b/0xa10
? tomoyo_file_ioctl+0x28/0x30
? vmci_host_do_alloc_queuepair.isra.9+0x1c0/0x1c0
__x64_sys_ioctl+0xea/0x120
do_syscall_64+0x34/0xb0
entry_SYSCALL_64_after_hwframe+0x44/0xae
When a queue pair is created by the following call, it will not
register the user memory if the page_store is NULL, and the
entry->state will be set to VMCIQPB_CREATED_NO_MEM.
vmci_host_unlocked_ioctl
vmci_host_do_alloc_queuepair
vmci_qp_broker_alloc
qp_broker_alloc
qp_broker_create // set entry->state = VMCIQPB_CREATED_NO_MEM;
When unmapping this queue pair, qp_host_unregister_user_memory() will
be called to unregister the non-existent user memory, which will
result in a null pointer reference. It will also change
VMCIQPB_CREATED_NO_MEM to VMCIQPB_CREATED_MEM, which should not be
present in this operation.
Only when the qp broker has mem, it can unregister the user
memory when unmapping the qp broker.
Only when the qp broker has no mem, it can register the user
memory when mapping the qp broker.
Fixes: 06164d2b72 ("VMCI: queue pairs implementation.")
Cc: stable <stable@vger.kernel.org>
Reported-by: Hulk Robot <hulkci@huawei.com>
Reviewed-by: Jorgen Hansen <jhansen@vmware.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Link: https://lore.kernel.org/r/20210818124845.488312-1-wanghai38@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7272b591c4 ]
In ibmasm_init_one, it calls ibmasm_init_remote_input_dev().
Inside ibmasm_init_remote_input_dev, mouse_dev and keybd_dev are
allocated by input_allocate_device(), and assigned to
sp->remote.mouse_dev and sp->remote.keybd_dev respectively.
In the err_free_devices error branch of ibmasm_init_one,
mouse_dev and keybd_dev are freed by input_free_device(), and return
error. Then the execution runs into error_send_message error branch
of ibmasm_init_one, where ibmasm_free_remote_input_dev(sp) is called
to unregister the freed sp->remote.mouse_dev and sp->remote.keybd_dev.
My patch add a "error_init_remote" label to handle the error of
ibmasm_init_remote_input_dev(), to avoid the uaf bugs.
Signed-off-by: Lv Yunlong <lyl2019@mail.ustc.edu.cn>
Link: https://lore.kernel.org/r/20210426170620.10546-1-lyl2019@mail.ustc.edu.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 40cc3a80bb upstream.
gcc-11 starts warning about misleading indentation inside of macros:
drivers/misc/kgdbts.c: In function ‘kgdbts_break_test’:
drivers/misc/kgdbts.c:103:9: error: this ‘if’ clause does not guard... [-Werror=misleading-indentation]
103 | if (verbose > 1) \
| ^~
drivers/misc/kgdbts.c:200:9: note: in expansion of macro ‘v2printk’
200 | v2printk("kgdbts: breakpoint complete\n");
| ^~~~~~~~
drivers/misc/kgdbts.c:105:17: note: ...this statement, but the latter is misleadingly indented as if it were guarded by the ‘if’
105 | touch_nmi_watchdog(); \
| ^~~~~~~~~~~~~~~~~~
The code looks correct to me, so just reindent it for readability.
Fixes: e8d31c204e ("kgdb: add kgdb internal test suite")
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20210322164308.827846-1-arnd@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3641762c1c upstream.
Before this commit lis3lv02d_get_pwron_wait() had a WARN_ONCE() to catch
a potential divide by 0. WARN macros should only be used to catch internal
kernel bugs and that is not the case here. We have been receiving a lot of
bug reports about kernel backtraces caused by this WARN.
The div value being checked comes from the lis3->odrs[] array. Which
is sized to be a power-of-2 matching the number of bits in lis3->odr_mask.
The only lis3 model where this array is not entirely filled with non zero
values. IOW the only model where we can hit the div == 0 check is the
3dc ("8 bits 3DC sensor") model:
int lis3_3dc_rates[16] = {0, 1, 10, 25, 50, 100, 200, 400, 1600, 5000};
Note the 0 value at index 0, according to the datasheet an odr index of 0
means "Power-down mode". HP typically uses a lis3 accelerometer for HDD
fall protection. What I believe is happening here is that on newer
HP devices, which only contain a SDD, the BIOS is leaving the lis3 device
powered-down since it is not used for HDD fall protection.
Note that the lis3_3dc_rates array initializer only specifies 10 values,
which matches the datasheet. So it also contains 6 zero values at the end.
Replace the WARN with a normal check, which treats an odr index of 0
as power-down and uses a normal dev_err() to report the error in case
odr index point past the initialized part of the array.
Fixes: 1510dd5954 ("lis3lv02d: avoid divide by zero due to unchecked")
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=785814
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1817027
BugLink: https://bugs.centos.org/view.php?id=10720
Link: https://lore.kernel.org/r/20210217102501.31758-1-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5a16c53540 ]
When the VMCI host support releases guest memory in the case where
the VM was killed, the pinned guest pages aren't locked. Use
set_page_dirty_lock() instead of set_page_dirty().
Testing done: Killed VM while having an active VMCI based vSocket
connection and observed warning from ext4. With this fix, no
warning was observed. Ran various vSocket tests without issues.
Fixes: 06164d2b72 ("VMCI: queue pairs implementation.")
Reviewed-by: Vishnu Dasa <vdasa@vmware.com>
Signed-off-by: Jorgen Hansen <jhansen@vmware.com>
Link: https://lore.kernel.org/r/1611160360-30299-1-git-send-email-jhansen@vmware.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cc1a267986 ]
Since struct _mic_vring_info and vring are allocated together and follow
vring, if the vring_size() is not four bytes aligned, which will cause
the start address of struct _mic_vring_info is not four byte aligned.
For example, when vring entries is 128, the vring_size() will be 5126
bytes. The _mic_vring_info struct layout in ddr looks like:
0x90002400: 00000000 00390000 EE010000 0000C0FF
Here 0x39 is the avail_idx member, and 0xC0FFEE01 is the magic member.
When EP use ioread32(magic) to reads the magic in RC's share memory, it
will cause kernel panic on ARM64 platform due to the cross-byte io read.
Here read magic in user space use le32toh(vr0->info->magic) will meet
the same issue.
So add round_up(x,4) for vring_size, then the struct _mic_vring_info
will store in this way:
0x90002400: 00000000 00000000 00000039 C0FFEE01
Which will avoid kernel panic when read magic in struct _mic_vring_info.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Link: https://lore.kernel.org/r/20200929091106.24624-4-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 90ca6333fd ]
In a couple of places in qp_host_get_user_memory(),
get_user_pages_fast() is called without properly checking for errors. If
e.g. -EFAULT is returned, this negative value will then be passed on to
qp_release_pages(), which expects a u64 as input.
Fix this by only calling qp_release_pages() when we have a positive
number returned.
Fixes: 06164d2b72 ("VMCI: queue pairs implementation.")
Signed-off-by: Alex Dewar <alex.dewar90@gmail.com>
Link: https://lore.kernel.org/r/20200825164522.412392-1-alex.dewar90@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 85dc2c65e6 ]
Clang warns when multiple pairs of parentheses are used for a single
conditional statement.
drivers/misc/echo/echo.c:384:27: warning: equality comparison with
extraneous parentheses [-Wparentheses-equality]
if ((ec->nonupdate_dwell == 0)) {
~~~~~~~~~~~~~~~~~~~~^~~~
drivers/misc/echo/echo.c:384:27: note: remove extraneous parentheses
around the comparison to silence this warning
if ((ec->nonupdate_dwell == 0)) {
~ ^ ~
drivers/misc/echo/echo.c:384:27: note: use '=' to turn this equality
comparison into an assignment
if ((ec->nonupdate_dwell == 0)) {
^~
=
1 warning generated.
Remove them and while we're at it, simplify the zero check as '!var' is
used more than 'var == 0'.
Reported-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
