commit a02dcde595 upstream.
A new warning in clang points out a few places in this driver where a
bitwise OR is being used with boolean types:
drivers/input/touchscreen.c:81:17: warning: use of bitwise '|' with boolean operands [-Wbitwise-instead-of-logical]
data_present = touchscreen_get_prop_u32(dev, "touchscreen-min-x",
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
This use of a bitwise OR is intentional, as bitwise operations do not
short circuit, which allows all the calls to touchscreen_get_prop_u32()
to happen so that the last parameter is initialized while coalescing the
results of the calls to make a decision after they are all evaluated.
To make this clearer to the compiler, use the '|=' operator to assign
the result of each touchscreen_get_prop_u32() call to data_present,
which keeps the meaning of the code the same but makes it obvious that
every one of these calls is expected to happen.
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reported-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Link: https://lore.kernel.org/r/20211014205757.3474635-1-nathan@kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 41e81022a0 upstream.
The direction of the pipe argument must match the request-type direction
bit or control requests may fail depending on the host-controller-driver
implementation.
Fix the four control requests which erroneously used usb_rcvctrlpipe().
Fixes: 1d3e20236d ("[PATCH] USB: usbtouchscreen: unified USB touchscreen driver")
Fixes: 24ced062a2 ("usbtouchscreen: add support for DMC TSC-10/25 devices")
Fixes: 9e3b25837a ("Input: usbtouchscreen - add support for e2i touchscreen controller")
Signed-off-by: Johan Hovold <johan@kernel.org>
Cc: stable@vger.kernel.org # 2.6.17
Link: https://lore.kernel.org/r/20210524092048.4443-1-johan@kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e479187748 ]
Some buggy BIOS-es bring up the touchscreen-controller in a stuck
state where it blocks the I2C bus. Specifically this happens on
the Jumper EZpad 7 tablet model.
After much poking at this problem I have found that the following steps
are necessary to unstuck the chip / bus:
1. Turn off the Silead chip.
2. Try to do an I2C transfer with the chip, this will fail in response to
which the I2C-bus-driver will call: i2c_recover_bus() which will unstuck
the I2C-bus. Note the unstuck-ing of the I2C bus only works if we first
drop the chip of the bus by turning it off.
3. Turn the chip back on.
On the x86/ACPI systems were this problem is seen, step 1. and 3. require
making ACPI calls and dealing with ACPI Power Resources. This commit adds
a workaround which runtime-suspends the chip to turn it off, leaving it up
to the ACPI subsystem to deal with all the ACPI specific details.
There is no good way to detect this bug, so the workaround gets activated
by a new "silead,stuck-controller-bug" boolean device-property. Since this
is only used on x86/ACPI, this will be set by model specific device-props
set by drivers/platform/x86/touchscreen_dmi.c. Therefor this new
device-property is not documented in the DT-bindings.
Dmesg will contain the following messages on systems where the workaround
is activated:
[ 54.309029] silead_ts i2c-MSSL1680:00: [Firmware Bug]: Stuck I2C bus: please ignore the next 'controller timed out' error
[ 55.373593] i2c_designware 808622C1:04: controller timed out
[ 55.582186] silead_ts i2c-MSSL1680:00: Silead chip ID: 0x80360000
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210405202745.16777-1-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 03e2c9c782 ]
req->sample[1] is not naturally aligned at word boundary, and therefore we
should use get_unaligned_be16() when accessing it.
Fixes: 3eac5c7e44 ("Input: ads7846 - extend the driver for ads7845 controller support")
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 820830ec91 ]
In some rare cases the 32 bit Rt value will overflow if z2 and x is max,
z1 is minimal value and x_plate_ohms is relatively high (for example 800
ohm). This would happen on some screen age with low pressure.
There are two possible fixes:
- make Rt 64bit
- reorder calculation to avoid overflow
The second variant seems to be preferable, since 64 bit calculation on
32 bit system is a bit more expensive.
Fixes: ffa458c1bd ("spi: ads7846 driver")
Co-developed-by: David Jander <david@protonic.nl>
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20201113112240.1360-1-o.rempel@pengutronix.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6cad4e269e ]
Return statements in functions returning bool should use true or false
instead of an integer value.
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e112324cc0 ]
The EP0700MLP1 returns bogus data on the first register read access
(reading the threshold parameter from register 0x00):
edt_ft5x06 2-0038: crc error: 0xfc expected, got 0x40
It ignores writes until then. This patch adds a dummy read after which
the number of sensors and parameter read/writes work correctly.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Tested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 97e24b0953 upstream.
The driver misses a check for devm_thermal_zone_of_sensor_register().
Add a check to fix it.
Fixes: e28d0c9cd3 ("input: convert sun4i-ts to use devm_thermal_zone_of_sensor_register")
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6b32391ed6 upstream.
Make sure to use the current alternate setting when verifying the
interface descriptors to avoid binding to an invalid interface.
This in turn could cause the driver to misbehave or trigger a WARN() in
usb_submit_urb() that kernels with panic_on_warn set would choke on.
Fixes: bdb5c57f20 ("Input: add sur40 driver for Samsung SUR40 (aka MS Surface 2.0/Pixelsense)")
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Vladis Dronov <vdronov@redhat.com>
Link: https://lore.kernel.org/r/20191210113737.4016-8-johan@kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 463fa44eec ]
Across suspend and resume, we are seeing error messages like the following:
atmel_mxt_ts i2c-PRP0001:00: __mxt_read_reg: i2c transfer failed (-121)
atmel_mxt_ts i2c-PRP0001:00: Failed to read T44 and T5 (-121)
This occurs because the driver leaves its IRQ enabled. Upon resume, there
is an IRQ pending, but the interrupt is serviced before both the driver and
the underlying I2C bus have been resumed. This causes EREMOTEIO errors.
Disable the IRQ in suspend, and re-enable it on resume. If there are cases
where the driver enters suspend with interrupts disabled, that's a bug we
should fix separately.
Signed-off-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 79aae6acbe ]
The device md->input is used after it is released. Setting the device
data to NULL is unnecessary as the device is never used again. Instead,
md->input should be assigned NULL to avoid accessing the freed memory
accidently. Besides, checking md->si against NULL is superfluous as it
points to a variable address, which cannot be NULL.
Signed-off-by: Pan Bian <bianpan2016@163.com>
Link: https://lore.kernel.org/r/1572936379-6423-1-git-send-email-bianpan2016@163.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dde2744321 ]
A certain silead controller (Chip ID: 0x56810000) loses its firmware
after suspend, causing the resume to fail. This patch tries to load
the firmware, should a resume error occur and retries the resuming.
Signed-off-by: Julian Sax <jsbc@gmx.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 193c2a07cf ]
Locking the root adapter for __i2c_transfer will deadlock if the
device sits behind a mux-locked I2C mux. Switch to the finer-grained
i2c_lock_bus with the I2C_LOCK_SEGMENT flag. If the device does not
sit behind a mux-locked mux, the two locking variants are equivalent.
Signed-off-by: Peter Rosin <peda@axentia.se>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 36f5d9ef26 ]
The driver only registers one input device, which uses the screen
parameters from the first T9 instance. The first T63 instance also uses
those parameters.
It is incorrect to send input reports from the second instances of these
objects if they are enabled: the input scaling will be wrong and the
positions will be mashed together.
This also causes problems on Android if the number of slots exceeds 32.
In the future, this could be handled by looking for enabled touch object
instances and creating an input device for each one.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Benson Leung <bleung@chromium.org>
Acked-by: Yufeng Shen <miletus@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f372b81101 upstream.
This patch adds the correct platform data information for the Caroline
Chromebook, so that the mouse button does not get stuck in pressed state
after the first click.
The Samus button keymap and platform data definition are the correct
ones for Caroline, so they have been reused here.
Signed-off-by: Vittorio Gambaletta <linuxbugs@vittgam.net>
Signed-off-by: Salvatore Bellizzi <lkml@seppia.net>
Tested-by: Guenter Roeck <groeck@chromium.org>
Cc: stable@vger.kernel.org
[dtor: adjusted vendor spelling to match shipping firmware]
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 95123fc435 ]
The name field in structure i2c_device_id is 20 characters, and we expect
it to be NULL-terminated, however we are trying to stuff it with 21 bytes
and thus NULL-terminator is lost. This causes issues when one creates
device with name "MICROCHIP_AR1021_I2C" as i2c core cuts off the last "C",
and automatic module loading by alias does not work as result.
The -I2C suffix in the device name is superfluous, we know what bus we are
dealing with, so let's drop it. Also, no other driver uses capitals, and
the manufacturer name is normally not included, except in very rare cases
of incompatible name collisions.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=116211
Fixes: dd4cae8bf1 ("Input: Add Microchip AR1021 i2c touchscreen")
Reviewed-By: Christian Gmeiner <christian.gmeiner@gmail.com>
Tested-by: Martin Kepplinger <martin.kepplinger@ginzinger.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 906bf7daa0 upstream.
Fix child node-lookup during probe, which ended up searching the whole
device tree depth-first starting at parent rather than just matching on
its children.
To make things worse, the parent node was prematurely freed, while the
child node was leaked.
Fixes: 2e57d56747 ("mfd: 88pm860x: Device tree support")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 92461f5d72 upstream.
Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer or accessing memory that lie beyond the end of the endpoint
array should a malicious device lack the expected endpoints.
Fixes: bdb5c57f20 ("Input: add sur40 driver for Samsung SUR40... ")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
