[ Upstream commit 3b384cc74b ]
Looks like the driver sleep pins configuration is unusable. Adding the
sleep pins causes the usb phy to not respond. We need to use the default
pins in probe, and only set sleep pins at phy_mdm6600_device_power_off().
As the modem can also be booted to a serial port mode for firmware
flashing, let's make the pin changes limited to probe and remove. For
probe, we get the default pins automatically. We only need to set the
sleep pins in phy_mdm6600_device_power_off() to prevent the modem from
waking up because the gpio line glitches.
If it turns out that we need a separate state for phy_mdm6600_power_on()
and phy_mdm6600_power_off(), we can use the pinctrl idle state.
Cc: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Fixes: 2ad2af0816 ("phy: mapphone-mdm6600: Improve phy related runtime PM calls")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20230913060433.48373-3-tony@atomide.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 19a1d46bd6 ]
inno_write is used to configure 0xaa reg, that also hold the
POST_PLL_POWER_DOWN bit.
When POST_PLL_REFCLK_SEL_TMDS is configured the power down bit is not
taken into consideration.
Fix this by keeping the power down bit until configuration is complete.
Also reorder the reg write order for consistency.
Fixes: 53706a1168 ("phy: add Rockchip Innosilicon hdmi phy")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Link: https://lore.kernel.org/r/20230615171005.2251032-5-jonas@kwiboo.se
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d5ef343c1d ]
inno_hdmi_phy_rk3328_clk_recalc_rate() is returning a rate not found
in the pre pll config table when the fractal divider is used.
This can prevent proper power_on because a tmdsclock for the new rate
is not found in the pre pll config table.
Fix this by saving and returning a rounded pixel rate that exist
in the pre pll config table.
Fixes: 53706a1168 ("phy: add Rockchip Innosilicon hdmi phy")
Signed-off-by: Zheng Yang <zhengyang@rock-chips.com>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Link: https://lore.kernel.org/r/20230615171005.2251032-3-jonas@kwiboo.se
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 13c088cf36 ]
The size of array 'priv->ports[]' is INNO_PHY_PORT_NUM.
In the for loop, 'i' is used as the index for array 'priv->ports[]'
with a check (i > INNO_PHY_PORT_NUM) which indicates that
INNO_PHY_PORT_NUM is allowed value for 'i' in the same loop.
This > comparison needs to be changed to >=, otherwise it potentially leads
to an out of bounds write on the next iteration through the loop
Fixes: ba8b0ee81f ("phy: add inno-usb2-phy driver for hi3798cv200 SoC")
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
Link: https://lore.kernel.org/r/20230721090558.3588613-1-harshit.m.mogalapalli@oracle.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c3966ced8e ]
Smatch reports the following error:
drivers/phy/qualcomm/phy-qcom-usb-hsic.c:82 qcom_usb_hsic_phy_power_on()
warn: 'uphy->cal_clk' from clk_prepare_enable() not released on lines:
58.
drivers/phy/qualcomm/phy-qcom-usb-hsic.c:82 qcom_usb_hsic_phy_power_on()
warn: 'uphy->cal_sleep_clk' from clk_prepare_enable() not released on
lines: 58.
drivers/phy/qualcomm/phy-qcom-usb-hsic.c:82 qcom_usb_hsic_phy_power_on()
warn: 'uphy->phy_clk' from clk_prepare_enable() not released on lines:
58.
Fix this by calling proper clk_disable_unprepare calls.
Fixes: 0b56e9a7e8 ("phy: Group vendor specific phy drivers")
Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20220914051334.69282-1-dzm91@hust.edu.cn
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d644e0d798 ]
The pm_runtime_enable will increase power disable depth.
If the probe fails, we should use pm_runtime_disable() to balance
pm_runtime_enable(). And use pm_runtime_dont_use_autosuspend() to
undo pm_runtime_use_autosuspend()
In the PM Runtime docs:
Drivers in ->remove() callback should undo the runtime PM changes done
in ->probe(). Usually this means calling pm_runtime_disable(),
pm_runtime_dont_use_autosuspend() etc.
We should do this in error handling.
Fixes: f7f50b2a7b ("phy: mapphone-mdm6600: Add runtime PM support for n_gsm on USB suspend")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Link: https://lore.kernel.org/r/20220301024615.31899-1-linmq006@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3153fa38e3 ]
According to the comment of the function phy_mipi_dphy_get_default_config(),
it uses minimum D-PHY timings based on MIPI D-PHY specification. They are
derived from the valid ranges specified in Section 6.9, Table 14, Page 41
of the D-PHY specification (v1.2). The table 14 explicitly mentions that
the minimum T-LPX parameter is 50 nanoseconds and the minimum TA-SURE
parameter is T-LPX nanoseconds. Likewise, the kernel doc of the 'lpx' and
'ta_sure' members of struct phy_configure_opts_mipi_dphy mentions that
the minimum values are 50000 picoseconds and @lpx picoseconds respectively.
Also, the function phy_mipi_dphy_config_validate() checks if cfg->lpx is
less than 50000 picoseconds and if cfg->ta_sure is less than cfg->lpx,
which hints the same minimum values.
Without this patch, the function phy_mipi_dphy_get_default_config()
wrongly sets cfg->lpx to 60000 picoseconds and cfg->ta_sure to 2 * cfg->lpx.
So, let's correct them to 50000 picoseconds and cfg->lpx respectively.
Note that I've only tested the patch with RM67191 DSI panel on i.MX8mq EVK.
Help is needed to test with other i.MX8mq, Meson and Rockchip platforms,
as I don't have the hardwares.
Fixes: dddc97e823 ("phy: dphy: Add configuration helpers")
Cc: Andrzej Hajda <andrzej.hajda@intel.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Vinod Koul <vkoul@kernel.org>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Link: https://lore.kernel.org/r/20220216071257.1647703-1-victor.liu@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4a90bbb478 ]
The current driver uses a value from register TEST_O as the original
value for register TEST_I, though, the value is overwritten by "param",
so there is a bug that the original value isn't no longer used.
The value of TEST_O[7:0] should be masked with "mask", replaced with
"param", and placed in the bitfield TESTI_DAT_MASK as new TEST_I value.
Fixes: c6d9b13241 ("phy: socionext: add PCIe PHY driver support")
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Link: https://lore.kernel.org/r/1623037842-19363-1-git-send-email-hayashi.kunihiko@socionext.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e1723d8b87 ]
This driver's remove path calls cancel_delayed_work(). However, that
function does not wait until the work function finishes. This means
that the callback function may still be running after the driver's
remove function has finished, which would result in a use-after-free.
Fix by calling cancel_delayed_work_sync(), which ensures that
the work is properly cancelled, no longer running, and unable
to re-schedule itself.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20210407092716.3270248-1-yangyingliang@huawei.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 764257d906 ]
On deferred probe, we will get the following splat:
cpcap-usb-phy cpcap-usb-phy.0: could not initialize VBUS or ID IIO: -517
WARNING: CPU: 0 PID: 21 at drivers/regulator/core.c:2123 regulator_put+0x68/0x78
...
(regulator_put) from [<c068ebf0>] (release_nodes+0x1b4/0x1fc)
(release_nodes) from [<c068a9a4>] (really_probe+0x104/0x4a0)
(really_probe) from [<c068b034>] (driver_probe_device+0x58/0xb4)
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20201230102105.11826-1-tony@atomide.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit ea17a0f153 upstream.
Driver ->power_on and ->power_off callbacks leaks internal SMCC firmware
return codes to phy caller. This patch converts SMCC error codes to
standard linux errno codes. Include file linux/arm-smccc.h already provides
defines for SMCC error codes, so use them instead of custom driver defines.
Note that return value is signed 32bit, but stored in unsigned long type
with zero padding.
Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Link: https://lore.kernel.org/r/20200902144344.16684-2-pali@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 05942b8c36 ]
The USB phy takes some time to reset, so make sure we give it to it. The
delay length was taken from the 4x12 phy driver.
This manifested in issues with the DWC2 driver since commit fe369e1826
("usb: dwc2: Make dwc2_readl/writel functions endianness-agnostic.")
where the endianness check would read the DWC ID as 0 due to the phy still
resetting, resulting in the wrong endian mode being chosen.
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Link: https://lore.kernel.org/r/BN6PR04MB06605D52502816E500683553A3D10@BN6PR04MB0660.namprd04.prod.outlook.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1dea06cd64 ]
The mvneta hardware appears to lock up in various random ways when
repeatedly switching speeds between 1G and 2.5G, which involves
reprogramming the COMPHY. It is not entirely clear why this happens,
but best guess is that reprogramming the COMPHY glitches mvneta clocks
causing the hardware to fail. It seems that rebooting resolves the
failure, but not down/up cycling the interface alone.
Various other approaches have been tried, such as trying to cleanly
power down the COMPHY and then take it back through the power up
initialisation, but this does not seem to help.
It was finally noticed that u-boot's last step when configuring a
COMPHY for "SGMII" mode was to poke at a register described as
"GBE_CONFIGURATION_REG", which is undocumented in any external
documentation. All that we have is the fact that u-boot sets a bit
corresponding to the "SGMII" lane at the end of COMPHY initialisation.
Experimentation shows that if we clear this bit prior to changing the
speed, and then set it afterwards, mvneta does not suffer this problem
on the SolidRun Clearfog when switching speeds between 1G and 2.5G.
This problem was found while script-testing phylink.
This fix also requires the corresponding change to DT to be effective.
See "ARM: dts: armada-38x: fix NETA lockup when repeatedly switching
speeds".
Fixes: 14dc100b44 ("phy: armada38x: add common phy support")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/E1jxtRj-0003Tz-CG@rmk-PC.armlinux.org.uk
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 08b0ad375c ]
If CONFIG_DEBUG_SHIRQ was enabled, r8a77951-salvator-xs could boot
correctly. If we appended "earlycon keep_bootcon" to the kernel
command like, we could get kernel log like below.
SError Interrupt on CPU0, code 0xbf000002 -- SError
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.8.0-rc3-salvator-x-00505-g6c843129e6faaf01 #785
Hardware name: Renesas Salvator-X 2nd version board based on r8a77951 (DT)
pstate: 60400085 (nZCv daIf +PAN -UAO BTYPE=--)
pc : rcar_gen3_phy_usb2_irq+0x14/0x54
lr : free_irq+0xf4/0x27c
This means free_irq() calls the interrupt handler while PM runtime
is not getting if DEBUG_SHIRQ is enabled and rcar_gen3_phy_usb2_probe()
failed. To fix the issue, move the irq registration place to
rcar_gen3_phy_usb2_init() which is ready to handle the interrupts.
Note that after the commit 549b6b55b0 ("phy: renesas: rcar-gen3-usb2:
enable/disable independent irqs") which is merged into v5.2, since this
driver creates multiple phy instances, needs to check whether one of
phy instances is initialized. However, if we backport this patch to v5.1
or less, we don't need to check it because such kernel have single
phy instance.
Reported-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Fixes: 9f391c574e ("phy: rcar-gen3-usb2: add runtime ID/VBUS pin detection")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/1594986297-12434-2-git-send-email-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 38b1927e5b ]
Currently pointer phy0 is being dereferenced via the assignment of
phy on the call to phy_get_drvdata before phy0 is null checked, this
can lead to a null pointer dereference. Fix this by performing the
null check on phy0 before the call to phy_get_drvdata. Also replace
the phy0 == NULL check with the more usual !phy0 idiom.
Addresses-Coverity: ("Dereference before null check")
Fixes: e6f32efb1b ("phy: sun4i-usb: Make sure to disable PHY0 passby for peripheral mode")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20200625124428.83564-1-colin.king@canonical.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9376fa634a ]
Pro5 SoC has same scheme of USB3 ss-phy as Pro4, so the data for Pro5 is
equivalent to Pro4.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 58aa772931 ]
The "gmii" PHY interface mode is supported on TI AM335x/437x/5xx SoCs, so
don't fail if it's selected.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eefed634eb ]
- under PHY_INTERFACE_MODE_MII the 'mode' func parameter is assigned
instead of 'gmii_sel_mode' and it's working only because the default value
'gmii_sel_mode' is set to 0.
- console outputs use 'rgmii_id' and 'mode' values to print PHY mode
instead of using 'submode' value which is representing PHY interface mode
now.
This patch fixes above two cases.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 46b7edf1c7 upstream.
I've noticed that when writing data to the modem the writes can time out
at some point eventually. Looks like kicking the modem idle GPIO every
600 ms instead of once a second fixes the issue. Note that this rate is
different from our runtime PM autosuspend rate MDM6600_MODEM_IDLE_DELAY_MS
that we still want to keep at 1 second, so let's add a separate define for
PHY_MDM6600_IDLE_KICK_MS.
Fixes: f7f50b2a7b ("phy: mapphone-mdm6600: Add runtime PM support for n_gsm on USB suspend")
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Michael Scott <hashcode0f@gmail.com>
Cc: NeKit <nekit1000@gmail.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit be4e3c737e upstream.
We have an interrupt handler for the wake-up GPIO pin, but we're missing
the code to wake-up the system. This can cause timeouts receiving data
for the UART that shares the wake-up GPIO pin with the USB PHY.
All we need to do is just wake the system and kick the autosuspend
timeout to fix the issue.
Fixes: 5d1ebbda03 ("phy: mapphone-mdm6600: Add USB PHY driver for MDM6600 on Droid 4")
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Michael Scott <hashcode0f@gmail.com>
Cc: NeKit <nekit1000@gmail.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a89806c998 upstream.
Clang warns:
../drivers/phy/qualcomm/phy-qcom-apq8064-sata.c:83:4: warning:
misleading indentation; statement is not part of the previous 'if'
[-Wmisleading-indentation]
usleep_range(DELAY_INTERVAL_US, DELAY_INTERVAL_US + 50);
^
../drivers/phy/qualcomm/phy-qcom-apq8064-sata.c:80:3: note: previous
statement is here
if (readl_relaxed(addr) & mask)
^
1 warning generated.
This warning occurs because there is a space after the tab on this line.
Remove it so that the indentation is consistent with the Linux kernel
coding style and clang no longer warns.
Fixes: 1de990d8a1 ("phy: qcom: Add driver for QCOM APQ8064 SATA PHY")
Link: https://github.com/ClangBuiltLinux/linux/issues/816
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 63078b6ba0 ]
The micro-USB connector on Motorola Mapphone devices can be muxed between
the SoC and the mdm6600 modem. But even when used for the SoC, configuring
the PHY with ID pin grounded will wake up the modem from idle state. Looks
like the issue is probably caused by line glitches.
We can prevent the glitches by using a previously unknown mode of the
GPIO mux to prevent the USB lines from being connected to the moden while
configuring the USB PHY, and enable the USB lines after configuring the
PHY.
Note that this only prevents waking up mdm6600 as regular USB A-host mode,
and does not help when connected to a lapdock. The lapdock specific issue
still needs to be debugged separately.
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cd217ee686 ]
It's typical for the QHP PHY to take slightly above 1ms to initialize,
so increase the timeout of the PHY ready check to 10ms - as already done
in the downstream PCIe driver.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Tested-by: Evan Green <evgreen@chromium.org>
Tested-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4f510aa104 ]
Commit 287422a95f ("drm/rockchip: Round up _before_ giving to the clock framework")
changed what rate clk_round_rate() is called with, an additional 999 Hz
added to the requsted mode clock. This has caused a regression on RK3328
and presumably also on RK3228 because the inno-hdmi-phy clock requires an
exact match of the requested rate in the pre pll config table.
When an exact match is not found the parent clock rate (24MHz) is returned
to the clk_round_rate() caller. This cause wrong pixel clock to be used and
result in no-signal when configuring a mode on RK3328.
Fix this by rounding the rate down to closest 1000 Hz in round_rate func,
this allows an exact match to be found in pre pll config table.
Fixes: 287422a95f ("drm/rockchip: Round up _before_ giving to the clock framework")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
