commit b63f4053cc upstream.
According to xHCI spec section 4.6.1.1 and section 4.6.1.2,
after aborting a command on the command ring, xHC will
generate a command completion event with its completion
code set to Command Ring Stopped at least. If a command is
currently executing at the time of aborting a command, xHC
also generate a command completion event with its completion
code set to Command Abort. When the command ring is stopped,
software may remove, add, or rearrage Command Descriptors.
To cancel a command, software will initialize a command
descriptor for the cancel command, and add it into a
cancel_cmd_list of xhci. When the command ring is stopped,
software will find the command trbs described by command
descriptors in cancel_cmd_list and modify it to No Op
command. If software can't find the matched trbs, we can
think it had been finished.
This patch should be backported to kernels as old as 3.0, that contain
the commit 7ed603ecf8 "xhci: Add an
assertion to check for virt_dev=0 bug." That commit papers over a NULL
pointer dereference, and this patch fixes the underlying issue that
caused the NULL pointer dereference.
Note from Sarah: The TRB_TYPE_LINK_LE32 macro is not in the 3.0 stable
kernel, so I added it to this patch.
Signed-off-by: Elric Fu <elricfu1@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: Miroslav Sabljic <miroslav.sabljic@avl.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6e4468b9a0 upstream.
The patch is used to cancel command when the command isn't
acknowledged and a timeout occurs.
This patch should be backported to kernels as old as 3.0, that contain
the commit 7ed603ecf8 "xhci: Add an
assertion to check for virt_dev=0 bug." That commit papers over a NULL
pointer dereference, and this patch fixes the underlying issue that
caused the NULL pointer dereference.
Signed-off-by: Elric Fu <elricfu1@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: Miroslav Sabljic <miroslav.sabljic@avl.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b92cc66c04 upstream.
Software have to abort command ring and cancel command
when a command is failed or hang. Otherwise, the command
ring will hang up and can't handle the others. An example
of a command that may hang is the Address Device Command,
because waiting for a SET_ADDRESS request to be acknowledged
by a USB device is outside of the xHC's ability to control.
To cancel a command, software will initialize a command
descriptor for the cancel command, and add it into a
cancel_cmd_list of xhci.
Sarah: Fixed missing newline on "Have the command ring been stopped?"
debugging statement.
This patch should be backported to kernels as old as 3.0, that contain
the commit 7ed603ecf8 "xhci: Add an
assertion to check for virt_dev=0 bug." That commit papers over a NULL
pointer dereference, and this patch fixes the underlying issue that
caused the NULL pointer dereference.
Signed-off-by: Elric Fu <elricfu1@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: Miroslav Sabljic <miroslav.sabljic@avl.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c181bc5b5d upstream.
Adding cmd_ring_state for command ring. It helps to verify
the current command ring state for controlling the command
ring operations.
This patch should be backported to kernels as old as 3.0. The commit
7ed603ecf8 "xhci: Add an assertion to
check for virt_dev=0 bug." papers over the NULL pointer dereference that
I now believe is related to a timed out Set Address command. This (and
the four patches that follow it) contain the real fix that also allows
VIA USB 3.0 hubs to consistently re-enumerate during the plug/unplug
stress tests.
Signed-off-by: Elric Fu <elricfu1@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: Miroslav Sabljic <miroslav.sabljic@avl.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a6e097dfdf upstream.
The Intel XHCI specification says that after clearing the run/stop bit
the controller may take up to 16ms to halt. We've seen a device take
14ms, which with the current timeout of 10ms causes the kernel to
abort the suspend. Increasing the timeout to the recommended value
fixes the problem.
This patch should be backported to kernels as old as 2.6.37, that
contain the commit 5535b1d5f8 "USB: xHCI:
PCI power management implementation".
Signed-off-by: Michael Spang <spang@chromium.org>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 80fab3b244 upstream.
When a device with an isochronous endpoint is behind a hub plugged into
the Intel Panther Point xHCI host controller, and the driver submits
multiple frames per URB, the xHCI driver will set the Block Event
Interrupt (BEI) flag on all but the last TD for the URB. This causes
the host controller to place an event on the event ring, but not send an
interrupt. When the last TD for the URB completes, BEI is cleared, and
we get an interrupt for the whole URB.
However, under a Panther Point xHCI host controller, if the parent hub
is unplugged when one or more events from transfers with BEI set are on
the event ring, a port status change event is placed on the event ring,
but no interrupt is generated. This means URBs stop completing, and the
USB device disconnect is not noticed. Something like a USB headset will
cause mplayer to hang when the device is disconnected.
If another transfer is sent (such as running `sudo lsusb -v`), the next
transfer event seems to "unstick" the event ring, the xHCI driver gets
an interrupt, and the disconnect is reported to the USB core.
The fix is not to use the BEI flag under the Panther Point xHCI host.
This will impact power consumption and system responsiveness, because
the xHCI driver will receive an interrupt for every frame in all
isochronous URBs instead of once per URB.
Intel chipset developers confirm that this bug will be hit if the BEI
flag is used on any endpoint, not just ones that are behind a hub.
This patch should be backported to kernels as old as 3.0, that contain
the commit 69e848c209 "Intel xhci: Support
EHCI/xHCI port switching."
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 50d0206fca upstream.
This patch fixes a particularly nasty bug that was revealed by the ring
expansion patches. The bug has been present since the very beginning of
the xHCI driver history, and could have caused general protection faults
from bad memory accesses.
The first thing to note is that a Set TR Dequeue Pointer command can
move the dequeue pointer to a link TRB, if the canceled or stalled
transfer TD ended just before a link TRB. The function to increment the
dequeue pointer, inc_deq, was written before cancellation and stall
support was added. It assumed that the dequeue pointer could never
point to a link TRB. It would unconditionally increment the dequeue
pointer at the start of the function, check if the pointer was now on a
link TRB, and move it to the top of the next segment if so.
This means that if a Set TR Dequeue Point command moved the dequeue
pointer to a link TRB, a subsequent call to inc_deq() would move the
pointer off the segment and into la-la-land. It would then read from
that memory to determine if it was a link TRB. Other functions would
often call inc_deq() until the dequeue pointer matched some other
pointer, which means this function would quite happily read all of
system memory before wrapping around to the right pointer value.
Often, there would be another endpoint segment from a different ring
allocated from the same DMA pool, which would be contiguous to the
segment inc_deq just stepped off of. inc_deq would eventually find the
link TRB in that segment, and blindly move the dequeue pointer back to
the top of the correct ring segment.
The only reason the original code worked at all is because there was
only one ring segment. With the ring expansion patches, the dequeue
pointer would eventually wrap into place, but the dequeue segment would
be out-of-sync. On the second TD after the dequeue pointer was moved to
a link TRB, trb_in_td() would fail (because the dequeue pointer and
dequeue segment were out-of-sync), and this message would appear:
ERROR Transfer event TRB DMA ptr not part of current TD
This fixes bugzilla entry 4333 (option-based modem unhappy on USB 3.0
port: "Transfer event TRB DMA ptr not part of current TD", "rejecting
I/O to offline device"),
https://bugzilla.kernel.org/show_bug.cgi?id=43333
and possibly other general protection fault bugs as well.
This patch should be backported to kernels as old as 2.6.31. A separate
patch will be created for kernels older than 3.4, since inc_deq was
modified in 3.4 and this patch will not apply.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: James Ettle <theholyettlz@googlemail.com>
Tested-by: Matthew Hall <mhall@mhcomputing.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2963657819 upstream.
For non PCI-based stacks, this function call
usb_disable_xhci_ports(to_pci_dev(hcd->self.controller));
made from xhci_shutdown is not applicable.
Ideally, we wouldn't have any PCI-specific code on
a generic driver such as the xHCI stack, but it looks
like we should just stub usb_disable_xhci_ports() out
for non-PCI devices.
[ balbi@ti.com: slight improvement to commit log ]
This patch should be backported to kernels as old as 3.0, since the
commit it fixes (e95829f474 "xhci: Switch
PPT ports to EHCI on shutdown.") was marked for stable.
Signed-off-by: Moiz Sonasath<m-sonasath@ti.com>
Signed-off-by: Ruchika Kharwar <ruchika@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 29d214576f upstream.
On Intel Panther Point chipset USB 3.0 devices show up as
high-speed devices on powerup, but after an s3 cycle they are
correctly recognized as SuperSpeed. At powerup switch the port
to xHCI so that USB 3.0 devices are correctly recognized.
BugLink: http://bugs.launchpad.net/bugs/1000424
This patch should be backported to kernels as old as 3.0, that contain
commit ID 69e848c209 "Intel xhci: Support
EHCI/xHCI port switching."
Signed-off-by: Manoj Iyer <manoj.iyer@canonical.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e955a1cd08 upstream.
My test platform (Intel DX79SI) boots reliably under BIOS, but frequently
crashes when booting via UEFI. I finally tracked this down to the xhci
handoff code. It seems that reads from the device occasionally just return
0xff, resulting in xhci_find_next_cap_offset generating a value that's
larger than the resource region. We then oops when attempting to read the
value. Sanity checking that value lets us avoid the crash.
I've no idea what's causing the underlying problem, and xhci still doesn't
actually *work* even with this, but the machine at least boots which will
probably make further debugging easier.
This should be backported to kernels as old as 2.6.31, that contain the
commit 66d4eadd8d "USB: xhci: BIOS handoff
and HW initialization."
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 052c7f9ffb upstream.
The intent was to test whether the flag was set.
This patch should be backported to stable kernels as old as 3.0, since
it fixes a bug in commit e95829f474 "xhci:
Switch PPT ports to EHCI on shutdown.", which was marked for stable.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a96874a2a9 upstream.
With a previous patch to enable the EHCI/XHCI port switching, it switches
all the available ports.
The assumption is not correct because the BIOS may expect some ports
not switchable by the OS.
There are two more registers that contains the information of the switchable
and non-switchable ports.
This patch adds the checking code for the two register so that only the
switchable ports are altered.
This patch should be backported to kernels as old as 3.0, that contain
commit ID 69e848c209 "Intel xhci: Support
EHCI/xHCI port switching."
Signed-off-by: Keng-Yu Lin <kengyu@canonical.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3d037774b4 upstream.
There is a possibility of QH overlay region having reference to a stale
qTD pointer during unlink.
Consider an endpoint having two pending qTD before unlink process begins.
The endpoint's QH queue looks like this.
qTD1 --> qTD2 --> Dummy
To unlink qTD2, QH is removed from asynchronous list and Asynchronous
Advance Doorbell is programmed. The qTD1's next qTD pointer is set to
qTD2'2 next qTD pointer and qTD2 is retired upon controller's doorbell
interrupt. If QH's current qTD pointer points to qTD1, transfer overlay
region still have reference to qTD2. But qtD2 is just unlinked and freed.
This may cause EHCI system error. Fix this by updating qTD next pointer
in QH overlay region with the qTD next pointer of the current qTD.
Signed-off-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e95829f474 upstream.
The Intel desktop boards DH77EB and DH77DF have a hardware issue that
can be worked around by BIOS. If the USB ports are switched to xHCI on
shutdown, the xHCI host will send a spurious interrupt, which will wake
the system. Some BIOS will work around this, but not all.
The bug can be avoided if the USB ports are switched back to EHCI on
shutdown. The Intel Windows driver switches the ports back to EHCI, so
change the Linux xHCI driver to do the same.
Unfortunately, we can't tell the two effected boards apart from other
working motherboards, because the vendors will change the DMI strings
for the DH77EB and DH77DF boards to their own custom names. One example
is Compulab's mini-desktop, the Intense-PC. Instead, key off the
Panther Point xHCI host PCI vendor and device ID, and switch the ports
over for all PPT xHCI hosts.
The only impact this will have on non-effected boards is to add a couple
hundred milliseconds delay on boot when the BIOS has to switch the ports
over from EHCI to xHCI.
This patch should be backported to kernels as old as 3.0, that contain
the commit 69e848c209 "Intel xhci: Support
EHCI/xHCI port switching."
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: Denis Turischev <denis@compulab.co.il>
Tested-by: Denis Turischev <denis@compulab.co.il>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 22ceac1912 upstream.
The NEC/Renesas 720201 xHCI host controller does not complete its reset
within 250 milliseconds. In fact, it takes about 9 seconds to reset the
host controller, and 1 second for the host to be ready for doorbell
rings. Extend the reset and CNR polling timeout to 10 seconds each.
This patch should be backported to kernels as old as 2.6.31, that
contain the commit 66d4eadd8d "USB: xhci:
BIOS handoff and HW initialization."
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: Edwin Klein Mentink <e.kleinmentink@zonnet.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5cb7df2b2d upstream.
Gary reports that with recent kernels, he notices more xHCI driver
warnings:
xhci_hcd 0000:03:00.0: WARN Successful completion on short TX: needs XHCI_TRUST_TX_LENGTH quirk?
We think his Etron xHCI host controller may have the same buggy behavior
as the Fresco Logic xHCI host. When a short transfer is received, the
host will mark the transfer as successfully completed when it should be
marking it with a short completion.
Fix this by turning on the XHCI_TRUST_TX_LENGTH quirk when the Etron
host is discovered. Note that Gary has revision 1, but if Etron fixes
this bug in future revisions, the quirk will have no effect.
This patch should be backported to kernels as old as 2.6.36, that
contain a backported version of commit
1530bbc627 "xhci: Add new short TX quirk
for Fresco Logic host."
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: Gary E. Miller <gem@rellim.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 51c9e6c773 upstream, but modified
to get this to apply on 3.0.
If the user chooses to say "no" to CONFIG_USB_XHCI_HCD on a system
with an Intel Panther Point chipset, the PCI quirks code or the EHCI
driver will switch the ports over to the xHCI host, but the xHCI driver
will never load. The ports will be powered off and seem "dead" to the
user.
Fix this by only switching the ports over if CONFIG_USB_XHCI_HCD is
either compiled in, or compiled as a module.
This patch should be backported to the 3.0 stable kernel, since it
contains the commit 69e848c209 "Intel
xhci: Support EHCI/xHCI port switching."
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: Eric Anholt <eric.anholt@intel.com>
Reported-by: David Bein <d.bein@f5.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c2fb8a3fa2 upstream.
This patch (as1558) fixes a problem affecting several ASUS computers:
The machine crashes or corrupts memory when going into suspend if the
ehci-hcd driver is bound to any controllers. Users have been forced
to unbind or unload ehci-hcd before putting their systems to sleep.
After extensive testing, it was determined that the machines don't
like going into suspend when any EHCI controllers are in the PCI D3
power state. Presumably this is a firmware bug, but there's nothing
we can do about it except to avoid putting the controllers in D3
during system sleep.
The patch adds a new flag to indicate whether the problem is present,
and avoids changing the controller's power state if the flag is set.
Runtime suspend is unaffected; this matters only for system suspend.
However as a side effect, the controller will not respond to remote
wakeup requests while the system is asleep. Hence USB wakeup is not
functional -- but of course, this is already true in the current state
of affairs.
A similar patch has already been applied as commit
151b612847 (USB: EHCI: fix crash during
suspend on ASUS computers). The patch supersedes that one and reverts
it. There are two differences:
The old patch added the flag at the USB level; this patch
adds it at the PCI level.
The old patch applied to all chipsets with the same vendor,
subsystem vendor, and product IDs; this patch makes an
exception for a known-good system (based on DMI information).
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Dâniel Fraga <fragabr@gmail.com>
Tested-by: Andrey Rahmatullin <wrar@wrar.name>
Tested-by: Steven Rostedt <rostedt@goodmis.org>
Reviewed-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 622eb783fe upstream.
When system software decides to power down the xHC with the intent of
resuming operation at a later time, it will ask xHC to save the internal
state and restore it when resume to correctly recover from a power event.
Two bits are used to enable this operation: Save State and Restore State.
xHCI spec 4.23.2 says software should "Set the Controller Save/Restore
State flag in the USBCMD register and wait for the Save/Restore State
Status flag in the USBSTS register to transition to '0'". However, it does
not define how long software should wait for the SSS/RSS bit to transition
to 0.
Currently the timeout is set to 1ms. There is bug report
(https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1002697)
indicates that the timeout is too short for ASMedia ASM1042 host controller
to save/restore the state successfully. Increase the timeout to 10ms helps to
resolve the issue.
This patch should be backported to stable kernels as old as 2.6.37, that
contain the commit 5535b1d5f8 "USB: xHCI:
PCI power management implementation"
Signed-off-by: Andiry Xu <andiry.xu@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1530bbc627 upstream.
Sergio reported that when he recorded audio from a USB headset mic
plugged into the USB 3.0 port on his ASUS N53SV-DH72, the audio sounded
"robotic". When plugged into the USB 2.0 port under EHCI on the same
laptop, the audio sounded fine. The device is:
Bus 002 Device 004: ID 046d:0a0c Logitech, Inc. Clear Chat Comfort USB Headset
The problem was tracked down to the Fresco Logic xHCI host controller
not correctly reporting short transfers on isochronous IN endpoints.
The driver would submit a 96 byte transfer, the device would only send
88 or 90 bytes, and the xHCI host would report the transfer had a
"successful" completion code, with an untransferred buffer length of 8
or 6 bytes.
The successful completion code and non-zero untransferred length is a
contradiction. The xHCI host is supposed to only mark a transfer as
successful if all the bytes are transferred. Otherwise, the transfer
should be marked with a short packet completion code. Without the EHCI
bus trace, we wouldn't know whether the xHCI driver should trust the
completion code or the untransferred length. With it, we know to trust
the untransferred length.
Add a new xHCI quirk for the Fresco Logic host controller. If a
transfer is reported as successful, but the untransferred length is
non-zero, print a warning. For the Fresco Logic host, change the
completion code to COMP_SHORT_TX and process the transfer like a short
transfer.
This should be backported to stable kernels that contain the commit
f5182b4155 "xhci: Disable MSI for some
Fresco Logic hosts." That commit was marked for stable kernels as old
as 2.6.36.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: Sergio Correia <lists@uece.net>
Tested-by: Sergio Correia <lists@uece.net>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 33b2831ac8 upstream.
When the xHCI driver needs to clean up memory (perhaps due to a failed
register restore on resume from S3 or resume from S4), it needs to reset
the number of reserved TRBs on the command ring to zero. Otherwise,
several resume cycles (about 30) with a UAS device attached will
continually increment the number of reserved TRBs, until all command
submissions fail because there isn't enough room on the command ring.
This patch should be backported to kernels as old as 2.6.32,
that contain the commit 913a8a344f
"USB: xhci: Change how xHCI commands are handled."
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9c745995ae upstream.
While testing unplugging an UVC HD webcam with usb-redirection (so through
usbdevfs), my userspace usb-redir code was getting a value of -1 in
iso_frame_desc[n].status, which according to Documentation/usb/error-codes.txt
is not a valid value.
The source of this -1 is the default case in xhci-ring.c:process_isoc_td()
adding a kprintf there showed the value of trb_comp_code to be COMP_TX_ERR
in this case, so this patch adds handling for that completion code to
process_isoc_td().
This was observed and tested with the following xhci controller:
1033:0194 NEC Corporation uPD720200 USB 3.0 Host Controller (rev 04)
Note: I also wonder if setting frame->status to -1 (-EPERM) is the best we can
do, but since I cannot come up with anything better I've left that as is.
This patch should be backported to kernels as old as 2.6.36, which contain the
commit 04e51901dd "USB: xHCI: Isochronous
transfer implementation".
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1c12443ab8 upstream.
The upcoming Intel Lynx Point chipset includes an xHCI host controller
that can have ports switched from the EHCI host controller, just like
the Intel Panther Point xHCI host. This time, ports from both EHCI
hosts can be switched to the xHCI host controller. The PCI config
registers to do the port switching are in the exact same place in the
xHCI PCI configuration registers, with the same semantics.
Hooray for shipping patches for next-gen hardware before the current gen
hardware is even available for purchase!
This patch should be backported to stable kernels as old as 3.0,
that contain commit 69e848c209
"Intel xhci: Support EHCI/xHCI port switching."
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 151b612847 upstream.
This patch (as1545) fixes a problem affecting several ASUS computers:
The machine crashes or corrupts memory when going into suspend if the
ehci-hcd driver is bound to any controllers. Users have been forced
to unbind or unload ehci-hcd before putting their systems to sleep.
After extensive testing, it was determined that the machines don't
like going into suspend when any EHCI controllers are in the PCI D3
power state. Presumably this is a firmware bug, but there's nothing
we can do about it except to avoid putting the controllers in D3
during system sleep.
The patch adds a new flag to indicate whether the problem is present,
and avoids changing the controller's power state if the flag is set.
Runtime suspend is unaffected; this matters only for system suspend.
However as a side effect, the controller will not respond to remote
wakeup requests while the system is asleep. Hence USB wakeup is not
functional -- but of course, this is already true in the current state
of affairs.
This fixes Bugzilla #42728.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Steven Rostedt <rostedt@goodmis.org>
Tested-by: Andrey Rahmatullin <wrar@wrar.name>
Tested-by: Oleksij Rempel (fishor) <bug-track@fisher-privat.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dc75ce9d92 upstream.
This patch (as1542) changes the criterion ehci-hcd uses to tell when
it needs to resume the controller's root hub. A resume is needed when
a port status change is detected, obviously, but only if the root hub
is currently suspended.
Right now the driver tests whether the root hub is running, and that
is not the correct test. In particular, if the controller has died
then the root hub should not be restarted. In addition, some buggy
hardware occasionally requires the root hub to be running and
sending out SOF packets even while it is nominally supposed to be
suspended.
In the end, the test needs to be changed. Rather than checking whether
the root hub is currently running, the driver will now check whether
the root hub is currently suspended. This will yield the correct
behavior in all cases.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Peter Chen <B29397@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Jonathan Nieder <jrnieder@gmail.com>
commit 2fbe2bf1fd upstream.
This patch (as1544) fixes a problem affecting some EHCI controllers.
They can generate interrupts whenever the STS_FLR status bit is turned
on, even though that bit is masked out in the Interrupt Enable
register.
Since the driver doesn't use STS_FLR anyway, the patch changes the
interrupt routine to clear that bit whenever it is set, rather than
leaving it alone.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: Tomoya MORINAGA <tomoya.rohm@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c7713e7365 upstream.
The xHCI 1.0 spec errata released on June 13, 2011, changes the ordering
that the xHCI registers are saved and restored in. It moves the
interrupt pending (IMAN) and interrupt control (IMOD) registers to be
saved and restored last. I believe that's because the host controller
may attempt to fetch the event ring table when interrupts are
re-enabled. Therefore we need to restore the event ring registers
before we re-enable interrupts.
This should be backported to kernels as old as 2.6.37, that contain the
commit 5535b1d5f8 "USB: xHCI: PCI power
management implementation"
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: Elric Fu <elricfu1@gmail.com>
Cc: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 457a4f61f9 upstream.
The suspend operation of VIA xHCI host have some issues and
hibernate operation works fine, so The XHCI_RESET_ON_RESUME
quirk is added for it.
This patch should base on "xHCI: Don't write zeroed pointer
to xHC registers" that is released by Sarah. Otherwise, the
host system error will ocurr in the hibernate operation
process.
This should be backported to stable kernels as old as 2.6.37,
that contain the commit c877b3b2ad
"xhci: Add reset on resume quirk for asrock p67 host".
Signed-off-by: Elric Fu <elricfu1@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 95018a53f7 upstream.
Re-define XHCI_LEGACY_DISABLE_SMI and used it in right way. All SMI enable
bits will be cleared to zero and flag bits 29:31 are also cleared to zero.
Other bits should be presvered as Table 146.
This patch should be backported to kernels as old as 2.6.31.
Signed-off-by: Alex He <alex.he@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fb3d85bc71 upstream.
The xhci_save_registers() function saved the event ring dequeue pointer
in the s3 register structure, but xhci_restore_registers() never
restored it. No other code in the xHCI successful resume path would
ever restore it either. Fix that.
This should be backported to kernels as old as 2.6.37, that contain the
commit 5535b1d5f8 "USB: xHCI: PCI power
management implementation".
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: Elric Fu <elricfu1@gmail.com>
Cc: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 159e1fcc9a upstream.
When xhci_mem_cleanup() is called, we can't be sure if the xHC is
actually halted. We can ask the xHC to halt by writing to the RUN bit
in the command register, but that might timeout due to a HW hang.
If the host controller is still running, we should not write zeroed
values to the event ring dequeue pointers or base tables, the DCBAA
pointers, or the command ring pointers. Eric Fu reports his VIA VL800
host accesses the event ring pointers after a failed register restore on
resume from suspend. The hypothesis is that the host never actually
halted before the register write to change the event ring pointer to
zero.
Remove all writes of zeroed values to pointer registers in
xhci_mem_cleanup(). Instead, make all callers of the function reset the
host controller first, which will reset those registers to zero.
xhci_mem_init() is the only caller that doesn't first halt and reset the
host controller before calling xhci_mem_cleanup().
This should be backported to kernels as old as 2.6.32.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: Elric Fu <elricfu1@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4e833c0b87 upstream.
While we're at that, define IMAN bitfield to aid readability.
The interrupt enable bit should be set once on driver init, and we
shouldn't need to continually re-enable it. Commit c21599a3 introduced
a read of the irq_pending register, and that allows us to preserve the
state of the IE bit. Before that commit, we were blindly writing 0x3 to
the register.
This patch should be backported to kernels as old as 2.6.36, or ones
that contain the commit c21599a361 "USB:
xhci: Reduce reads and writes of interrupter registers".
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e90fc3cb08 upstream.
When build i.mx platform with imx_v6_v7_defconfig, and after adding
USB Gadget support, it has below build error:
CC drivers/usb/host/fsl-mph-dr-of.o
drivers/usb/host/fsl-mph-dr-of.c: In function 'fsl_usb2_device_register':
drivers/usb/host/fsl-mph-dr-of.c:97: error: 'struct pdev_archdata'
has no member named 'dma_mask'
It has discussed at: http://www.spinics.net/lists/linux-usb/msg57302.html
For PowerPC, there is dma_mask at struct pdev_archdata, but there is
no dma_mask at struct pdev_archdata for ARM. The pdev_archdata is
related to specific platform, it should NOT be accessed by
cross platform drivers, like USB.
The code for pdev_archdata should be useless, as for PowerPC,
it has already gotten the value for pdev->dev.dma_mask at function
arch_setup_pdev_archdata of arch/powerpc/kernel/setup-common.c.
Tested-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 68d07f64b8 upstream
Intel has a PCI USB xhci host controller on a new platform. It doesn't
have a line IRQ definition in BIOS. The Linux driver refuses to
initialize this controller, but Windows works well because it only depends
on MSI.
Actually, Linux also can work for MSI. This patch avoids the line IRQ
checking for USB3 HCDs in usb core PCI probe. It allows the xHCI driver
to try to enable MSI or MSI-X first. It will fail the probe if MSI
enabling failed and there's no legacy PCI IRQ.
This patch should be backported to kernels as old as 2.6.32.
[Maintainer note: This patch is a backport of commit
68d07f64b8 "USB: Don't fail USB3 probe on
missing legacy PCI IRQ." to the 3.0 kernel. Note, the original patch
description was wrong. We should not back port this to kernels older
than 2.6.36, since that was the first kernel to support MSI and MSI-X
for xHCI hosts. These systems will just not work without MSI support,
so the probe should fail on kernels older than 2.6.36.]
Signed-off-by: Alex Shi <alex.shi@intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 340a3504fd upstream.
The xHCI 0.96 spec says that HS bulk and control endpoint NAK rate must
be encoded as an exponent of two number of microframes. The endpoint
descriptor has the NAK rate encoded in number of microframes. We were
just copying the value from the endpoint descriptor into the endpoint
context interval field, which was not correct. This lead to the VIA
host rejecting the add of a bulk OUT endpoint from any USB 2.0 mass
storage device.
The fix is to use the correct encoding. Refactor the code to convert
number of frames to an exponential number of microframes, and make sure
we convert the number of microframes in HS bulk and control endpoints to
an exponent.
This should be back ported to kernels as old as 2.6.31, that contain the
commit dfa49c4ad1 "USB: xhci - fix math
in xhci_get_endpoint_interval"
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: Felipe Contreras <felipe.contreras@gmail.com>
Suggested-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3278a55a1a upstream.
The code to set the device removable bits in the USB 2.0 roothub
descriptor was accidentally looking at the USB 3.0 port registers
instead of the USB 2.0 registers. This can cause an oops if there are
more USB 2.0 registers than USB 3.0 registers.
This should be backported to kernels as old as 2.6.39, that contain the
commit 4bbb0ace9a "xhci: Return a USB 3.0
hub descriptor for USB3 roothub."
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cab928ee1f upstream.
On some systems with an Intel Panther Point xHCI host controller, the
BIOS disables the xHCI PCI device during boot, and switches the xHCI
ports over to EHCI. This allows the BIOS to access USB devices without
having xHCI support.
The downside is that the xHCI BIOS handoff mechanism will fail because
memory mapped I/O is not enabled for the disabled PCI device.
Jesse Barnes says this is expected behavior. The PCI core will enable
BARs before quirks run, but it will leave it in an undefined state, and
it may not have memory mapped I/O enabled.
Make the generic USB quirk handler call pci_enable_device() to re-enable
MMIO, and call pci_disable_device() once the host-specific BIOS handoff
is finished. This will balance the ref counts in the PCI core. When
the PCI probe function is called, usb_hcd_pci_probe() will call
pci_enable_device() again.
This should be back ported to kernels as old as 2.6.31. That was the
first kernel with xHCI support, and no one has complained about BIOS
handoffs failing due to memory mapped I/O being disabled on other hosts
(EHCI, UHCI, or OHCI).
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: Oliver Neukum <oneukum@suse.de>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e4436a7c17 upstream.
The Netlogic XLP SoC's on-chip USB controller appears as a PCI
USB device, but does not need the EHCI/OHCI handoff done in
usb/host/pci-quirks.c.
The pci-quirks.c is enabled for all vendors and devices, and is
enabled if USB and PCI are configured.
If we do not skip the qurik handling on XLP, the readb() call in
ehci_bios_handoff() will cause a crash since byte access is not
supported for EHCI registers in XLP.
Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cf840551a8 upstream.
When a TD length mismatch is found during isoc TRB enqueue, it directly
returns -EINVAL. However, isoc transfer is partially enqueued at this time,
and the ring should be cleared.
This should be backported to kernels as old as 2.6.36, which contain the
commit 522989a27c "xhci: Fix failed
enqueue in the middle of isoch TD."
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d0cd5d482b upstream.
The xHCI hub port code gets passed a zero-based port number by the USB
core. It then adds one to in order to find a device slot by port number
and device speed by calling xhci_find_slot_id_by_port. That function
clearly states it requires a one-based port number. The xHCI port
status change event handler was using a zero-based port number that it
got from find_faked_portnum_from_hw_portnum, not a one-based port
number. This lead to the doorbells never being rung for a device after
a resume, or worse, a different device with the same speed having its
doorbell rung (which could lead to bad power management in the xHCI host
controller).
This patch should be backported to kernels as old as 2.6.39.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2492c6e645 upstream.
Add missing iounmap in error handling code, in a case where the function
already preforms iounmap on some other execution path.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression e;
statement S,S1;
int ret;
@@
e = \(ioremap\|ioremap_nocache\)(...)
... when != iounmap(e)
if (<+...e...+>) S
... when any
when != iounmap(e)
*if (...)
{ ... when != iounmap(e)
return ...; }
... when any
iounmap(e);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c618759774 upstream.
Problems with NVIDIA's OHCI host controllers persist. After looking
carefully through the spec, I finally realized that when a controller
is reset it then automatically goes into a SUSPEND state in which it
is completely quiescent (no DMA and no IRQs) and from which it will
not awaken until the system puts it into the OPERATIONAL state.
Therefore there's no need to worry about controllers being in the
RESET state for extended periods, or remaining in the OPERATIONAL
state during system shutdown. The proper action for device
initialization is to put the controller into the RESET state (if it's
not there already) and then to issue a software reset. Similarly, the
proper action for device shutdown is simply to do a software reset.
This patch (as1499) implements such an approach. It simplifies
initialization and shutdown, and allows the NVIDIA shutdown-quirk code
to be removed.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Andre "Osku" Schmidt <andre.osku.schmidt@googlemail.com>
Tested-by: Arno Augustin <Arno.Augustin@web.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 18b7ede5f7 upstream.
[ removed the dwc3 portion of the patch as it didn't apply to
older kernels - gregkh]
According to USB 3.0 Specification Table 9-22, if
bmAttributes [4:0] are set to zero, it means "no
streams supported", but the way this helper was
defined on Linux, we will *always* have one stream
which might cause several problems.
For example on DWC3, we would tell the controller
endpoint has streams enabled and yet start transfers
with Stream ID set to 0, which would goof up the host
side.
While doing that, convert the macro to an inline
function due to the different checks we now need.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 71d85724bd upstream.
I encountered a result of COMP_2ND_BW_ERR while improving how the pwc
webcam driver handles not having the full usb1 bandwidth available to
itself.
I created the following test setup, a NEC xhci controller with a
single TT USB 2 hub plugged into it, with a usb keyboard and a pwc webcam
plugged into the usb2 hub. This caused the following to show up in dmesg
when trying to stream from the pwc camera at its highest alt setting:
xhci_hcd 0000:01:00.0: ERROR: unexpected command completion code 0x23.
usb 6-2.1: Not enough bandwidth for altsetting 9
And usb_set_interface returned -EINVAL, which caused my pwc code to not
do the right thing as it expected -ENOSPC.
This patch makes the xhci driver properly handle COMP_2ND_BW_ERR and makes
usb_set_interface return -ENOSPC as expected.
This should be backported to stable kernels as old as 2.6.32.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit bc677d5b64 upstream.
Add a new field num_mapped_sgs to struct urb so that we have a place to
store the number of mapped entries and can also retain the original
value of entries in num_sgs. Previously, usb_hcd_map_urb_for_dma()
would overwrite this with the number of mapped entries, which would
break dma_unmap_sg() because it requires the original number of entries.
This fixes warnings like the following when using USB storage devices:
------------[ cut here ]------------
WARNING: at lib/dma-debug.c:902 check_unmap+0x4e4/0x695()
ehci_hcd 0000:00:12.2: DMA-API: device driver frees DMA sg list with different entry count [map count=4] [unmap count=1]
Modules linked in: ohci_hcd ehci_hcd
Pid: 0, comm: kworker/0:1 Not tainted 3.2.0-rc2+ #319
Call Trace:
<IRQ> [<ffffffff81036d3b>] warn_slowpath_common+0x80/0x98
[<ffffffff81036de7>] warn_slowpath_fmt+0x41/0x43
[<ffffffff811fa5ae>] check_unmap+0x4e4/0x695
[<ffffffff8105e92c>] ? trace_hardirqs_off+0xd/0xf
[<ffffffff8147208b>] ? _raw_spin_unlock_irqrestore+0x33/0x50
[<ffffffff811fa84a>] debug_dma_unmap_sg+0xeb/0x117
[<ffffffff8137b02f>] usb_hcd_unmap_urb_for_dma+0x71/0x188
[<ffffffff8137b166>] unmap_urb_for_dma+0x20/0x22
[<ffffffff8137b1c5>] usb_hcd_giveback_urb+0x5d/0xc0
[<ffffffffa0000d02>] ehci_urb_done+0xf7/0x10c [ehci_hcd]
[<ffffffffa0001140>] qh_completions+0x429/0x4bd [ehci_hcd]
[<ffffffffa000340a>] ehci_work+0x95/0x9c0 [ehci_hcd]
...
---[ end trace f29ac88a5a48c580 ]---
Mapped at:
[<ffffffff811faac4>] debug_dma_map_sg+0x45/0x139
[<ffffffff8137bc0b>] usb_hcd_map_urb_for_dma+0x22e/0x478
[<ffffffff8137c494>] usb_hcd_submit_urb+0x63f/0x6fa
[<ffffffff8137d01c>] usb_submit_urb+0x2c7/0x2de
[<ffffffff8137dcd4>] usb_sg_wait+0x55/0x161
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 158886cd2c upstream.
When system enters suspend, xHCI driver clears command ring by writing zero
to all the TRBs. However, this also writes zero to the Link TRB, and the ring
is mangled. This may cause driver accesses wrong memory address and the
result is unpredicted.
When clear the command ring, keep the last Link TRB intact, only clear its
cycle bit. This should fix the "command ring full" issue reported by Oliver
Neukum.
This should be backported to stable kernels as old as 2.6.37, since the
commit 89821320 "xhci: Fix command ring replay after resume" is merged.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit e3420901eb upstream.
Fix a regression that was introduced by commit
811c926c53 (USB: EHCI: fix HUB TT scheduling
issue with iso transfer).
We detect an error if next == start, but this means uframe 0 can't be allocated
anymore for iso transfer...
Reported-by: Sander Eikelenboom <linux@eikelenboom.it>
Signed-off-by: Matthieu CASTET <castet.matthieu@free.fr>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 811c926c53 upstream.
The current TT scheduling doesn't allow to play and then record on a
full-speed device connected to a high speed hub.
The IN iso stream can only start on the first uframe (0-2 for a 165 us)
because of CSPLIT transactions.
For the OUT iso stream there no such restriction. uframe 0-5 are possible.
The idea of this patch is that the first uframe are precious (for IN TT iso
stream) and we should allocate the last uframes first if possible.
For that we reverse the order of uframe allocation (last uframe first).
Here an example :
hid interrupt stream
----------------------------------------------------------------------
uframe | 0 | 1 | 2 | 3 | 4 | 5 | 6 | 7 |
----------------------------------------------------------------------
max_tt_usecs | 125 | 125 | 125 | 125 | 125 | 125 | 30 | 0 |
----------------------------------------------------------------------
used usecs on a frame | 13 | 0 | 0 | 0 | 0 | 0 | 0 | 0 |
----------------------------------------------------------------------
iso OUT stream
----------------------------------------------------------------------
uframe | 0 | 1 | 2 | 3 | 4 | 5 | 6 | 7 |
----------------------------------------------------------------------
max_tt_usecs | 125 | 125 | 125 | 125 | 125 | 125 | 30 | 0 |
----------------------------------------------------------------------
used usecs on a frame | 13 | 125 | 39 | 0 | 0 | 0 | 0 | 0 |
----------------------------------------------------------------------
There no place for iso IN stream (uframe 0-2 are used) and we got "cannot
submit datapipe for urb 0, error -28: not enough bandwidth" error.
With the patch this become.
iso OUT stream
----------------------------------------------------------------------
uframe | 0 | 1 | 2 | 3 | 4 | 5 | 6 | 7 |
----------------------------------------------------------------------
max_tt_usecs | 125 | 125 | 125 | 125 | 125 | 125 | 30 | 0 |
----------------------------------------------------------------------
used usecs on a frame | 13 | 0 | 0 | 0 | 125 | 39 | 0 | 0 |
----------------------------------------------------------------------
iso IN stream
----------------------------------------------------------------------
uframe | 0 | 1 | 2 | 3 | 4 | 5 | 6 | 7 |
----------------------------------------------------------------------
max_tt_usecs | 125 | 125 | 125 | 125 | 125 | 125 | 30 | 0 |
----------------------------------------------------------------------
used usecs on a frame | 13 | 0 | 125 | 40 | 125 | 39 | 0 | 0 |
----------------------------------------------------------------------
Signed-off-by: Matthieu Castet <matthieu.castet@parrot.com>
Signed-off-by: Thomas Poussevin <thomas.poussevin@parrot.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
