commit 98a4f1ff7b upstream.
The pm qos NO_POWER_OFF flag is checked twice during usb device suspend
to see if the usb port power off condition is met. This is redundant and
also will prevent the port from being powered off if the NO_POWER_OFF
flag is changed to 1 from 0 after the device was already suspended.
More detail in the following link.
http://marc.info/?l=linux-usb&m=136543949130865&w=2
This patch should be backported to kernels as old as 3.7, that
contain the commit f7ac7787ad "usb/acpi:
Use ACPI methods to power off ports."
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit aa5ceae24b upstream.
The hub driver's usb_port_suspend() routine doesn't handle errors
related to Link Power Management properly. It always returns failure,
it doesn't try to clean up the wakeup setting, (in the case of system
sleep) it doesn't try to go ahead with the port suspend regardless,
and it doesn't try to apply the new power-off mechanism.
This patch fixes these problems.
Note: Sarah fixed this patch to apply against 3.11, since the original
commit (4fae6f0fa8 "USB: handle LPM errors
during device suspend correctly") called usb_disable_remote_wakeup,
which won't be added until 3.12.
This patch should be backported to kernels as old as 3.5, that
contain the commit 8306095fd2 "USB:
Disable USB 3.0 LPM in critical sections.". There will be merge
conflicts, since LTM wasn't added until 3.6.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b4f17a488a upstream.
While reading the config parsing code I noticed this check is missing, without
this check config->desc.wTotalLength can end up with a value larger then the
dev->rawdescriptors length for the config, and when userspace then tries to
get the rawdescriptors bad things may happen.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d49dad3e11 upstream.
Userspace can tell the kernel to power off any USB port, including ones
that are visible and connectible to users. When an attached USB device
goes into suspend, the port will be powered off if the
pm_qos_no_port_poweroff file for its port is set to 0, the device does
not have remote wakeup enabled, and the device is marked as persistent.
If the user disconnects the USB device while the port is powered off,
the current code does not handle that properly. If you disconnect a
device, and then run `lsusb -v -s` for the device, the device disconnect
does not get handled by the USB core. The runtime resume of the port
fails, because hub_port_debounce_be_connected() returns -ETIMEDOUT.
This means the port resume fails and khubd doesn't handle the USB device
disconnect. This leaves the device listed in lsusb, and the port's
runtime_status will be permanently marked as "error".
Fix this by ignoring the return value of hub_port_debounce_be_connected.
Users can disconnect USB devices while the ports are powered off, and we
must be able to handle that.
This patch should be backported to kernels as old as 3.9, that
contain the commit ad493e5e58 "usb: add
usb port auto power off mechanism"
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Lan Tianyu <tianyu.lan@intel.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6dd433e6cf upstream.
Both could want to submit the same URB. Some checks of the flag
intended to prevent that were missing.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f375fc520d upstream.
Commit 7e8d5cd93f ("USB: Add EHCI support for MX27 and MX31 based
boards") introduced code that could potentially lead to a NULL pointer
dereference on driver removal.
Fix this by checking for the value of pdata before dereferencing it.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3b716caf19 upstream.
Fix endianess bugs in parallel-port code which caused corrupt
control-requests to be issued on big-endian machines.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 69820e01aa upstream.
Since ohci-hcd supports runtime PM, the .pm field in its pci_driver
structure should be protected by CONFIG_PM rather than
CONFIG_PM_SLEEP.
Without this change, OHCI controllers won't do runtime suspend if
system suspend or hibernation isn't enabled.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b0d7ffd44b upstream.
We cannot request an IRQ with spinlocks held
as that would trigger a sleeping inside
spinlock warning.
Reported-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c8476fb855 upstream.
If a USB controller with XHCI_RESET_ON_RESUME goes to runtime suspend,
a reset will be performed upon runtime resume. Any previously suspended
devices attached to the controller will be re-enumerated at this time.
This will cause problems, for example, if an open system call on the
device triggered the resume (the open call will fail).
Note that this change is only relevant when persist_enabled is not set
for USB devices.
This patch should be backported to kernels as old as 3.0, that
contain the commit c877b3b2ad "xhci: Add
reset on resume quirk for asrock p67 host".
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 52fb61250a upstream.
The xHCI platform driver calls into usb_add_hcd to register the irq for
its platform device. It does not want the xHCI generic driver to
register an interrupt for it at all. The original code did that by
setting the XHCI_BROKEN_MSI quirk, which tells the xHCI driver to not
enable MSI or MSI-X for a PCI host.
Unfortunately, if CONFIG_PCI is enabled, and CONFIG_USB_DW3 is enabled,
the xHCI generic driver will attempt to register a legacy PCI interrupt
for the xHCI platform device in xhci_try_enable_msi(). This will result
in a bogus irq being registered, since the underlying device is a
platform_device, not a pci_device, and thus the pci_device->irq pointer
will be bogus.
Add a new quirk, XHCI_PLAT, so that the xHCI generic driver can
distinguish between a PCI device that can't handle MSI or MSI-X, and a
platform device that should not have its interrupts touched at all.
This quirk may be useful in the future, in case other corner cases like
this arise.
This patch should be backported to kernels as old as 3.9, that
contain the commit 00eed9c814 "USB: xhci:
correctly enable interrupts".
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: Yu Y Wang <yu.y.wang@intel.com>
Tested-by: Yu Y Wang <yu.y.wang@intel.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d257221854 upstream.
The gadget strings table should be null terminated.
usb_gadget_get_string() loops through the table
expecting a null at the end of the list.
Signed-off-by: Graham Williams <gwilli@broadcom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 52d5b9aba1 upstream.
Commit 94ae9843 (usb: phy: rename all phy drivers to phy-$name-usb.c)
renamed drivers/usb/phy/otg_fsm.h to drivers/usb/phy/phy-fsm-usb.h
but changed drivers/usb/phy/phy-fsm-usb.c to include not existing
"phy-otg-fsm.h" instead of new "phy-fsm-usb.h". This breaks building:
...
drivers/usb/phy/phy-fsm-usb.c:32:25: fatal error: phy-otg-fsm.h: No such file or directory
compilation terminated.
make[3]: *** [drivers/usb/phy/phy-fsm-usb.o] Error 1
This commit also missed to modify drivers/usb/phy/phy-fsl-usb.h
to include new "phy-fsm-usb.h" instead of "otg_fsm.h" resulting
in another build breakage:
...
In file included from drivers/usb/phy/phy-fsl-usb.c:46:0:
drivers/usb/phy/phy-fsl-usb.h:18:21: fatal error: otg_fsm.h: No such file or directory
compilation terminated.
make[3]: *** [drivers/usb/phy/phy-fsl-usb.o] Error 1
Fix both issues.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ec58fad1fe upstream.
This patch fixes a kernel panic that can occur when disconnecting a
wireless USB->serial device. When the serial device disconnects, the
device cleanup procedure ends up calling usb_hcd_disable_endpoint on the
serial device's endpoints. The wusbcore uses the ABORT_RPIPE command to
abort all transfers on the given endpoint but it does not properly give
back the URBs when the transfer results return from the HWA. This patch
prevents the transfer result processing code from bailing out when it sees
a WA_XFER_STATUS_ABORTED result code so that these urbs are flushed
properly by usb_hcd_disable_endpoint. It also updates wa_urb_dequeue to
handle the case where the endpoint has already been cleaned up when
usb_kill_urb is called which is where the panic originally occurred.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6c1ee66a0b upstream.
This fixes an issue where the bulk-in urb used for incoming data transfer
is not resubmitted if the packet recieved contains an error status. This
results in the driver locking until the port is closed and re-opened.
Tested on a custom board with a Cinterion GSM module.
Signed-off-by: Matt Burtch <matt@grid-net.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 24f531371d upstream.
Since commits 4005ad4390 (EHCI: implement new semantics for
URB_ISO_ASAP) and c75c5ab575 (ALSA: USB: adjust for changed 3.8 USB
API) became widely distributed, people have been experiencing problems
with audio transfers. The slightest underrun causes complete failure,
requiring the audio stream to be restarted.
It turns out that the current isochronous API doesn't handle underruns
in the best way. The ALSA developers would much rather have transfers
that are submitted too late be accepted and complete in the normal
fashion, rather than being refused outright.
This patch implements the requested approach. When an isochronous URB
submission is so late that all its scheduled slots have already
expired, a debugging message will be printed in the log and the URB
will be accepted as usual. Assuming it was submitted by a completion
handler (which is normally the case), it will complete shortly
thereafter with all the usb_iso_packet_descriptor status fields marked
-EXDEV.
This fixes (for ehci-hcd)
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1191603
It should be applied to all kernels that include commit 4005ad4390.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Maksim Boyko <maksboyko@yandex.ru>
CC: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ff8a43c10f upstream.
Make sure to fail properly if the device is not accepted during attach
in order to avoid null-pointer derefs (of missing interface private
data) at disconnect or release.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ef6c8c1d73 upstream.
The parallel-port code of the drivers used a stack allocated
control-request buffer for asynchronous (and possibly deferred) control
requests. This not only violates the no-DMA-from-stack requirement but
could also lead to corrupt control requests being submitted.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d551ec9b69 upstream.
Fix bug in device-type detection on big-endian machines originally
introduced by commit 0eafe4de ("USB: serial: mos7840: add support for
MCS7810 devices") which always matched on little-endian product ids.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e877dd2f25 upstream.
Fix endianess bugs in firmware handling introduced by commits cb7a7c6a
("ti_usb_3410_5052: add Multi-Tech modem support") and 05a3d905
("ti_usb_3410_5052: support alternate firmware") which made the driver
use the wrong firmware for certain devices on big-endian machines.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 481f2d4f89 upstream.
The USB hub driver's event handler contains a check to catch SuperSpeed
devices that transitioned into the SS.Inactive state and tries to fix
them with a reset. It decides whether to do a plain hub port reset or
call the usb_reset_device() function based on whether there was a device
attached to the port.
However, there are device/hub combinations (found with a JetFlash
Transcend mass storage stick (8564:1000) on the root hub of an Intel
LynxPoint PCH) which can transition to the SS.Inactive state on
disconnect (and stay there long enough for the host to notice). In this
case, above-mentioned reset check will call usb_reset_device() on the
stale device data structure. The kernel will send pointless LPM control
messages to the no longer connected device address and can even cause
several 5 second khubd stalls on some (buggy?) host controllers, before
finally accepting the device's fate amongst a flurry of error messages.
This patch makes the choice of reset dependent on the port status that
has just been read from the hub in addition to the existence of an
in-kernel data structure for the device, and only proceeds with the more
extensive reset if both are valid.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 683a0e4d79 upstream.
Silence compiler warnings on 64-bit systems introduced by commit
05cf0dec ("USB: mos7840: fix race in led handling") which uses the
usb-serial data pointer to temporarily store the device type during
probe but failed to add the required casts.
[gregkh - change uintptr_t to unsigned long]
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 05cf0dec5c upstream.
Fix race in LED handling introduced by commit 0eafe4de ("USB: serial:
mos7840: add support for MCS7810 devices") which reused the port control
urb for manipulating the LED without making sure that the urb is not
already in use. This could lead to the control urb being manipulated
while in flight.
Fix by adding a dedicated LED urb and ctrlrequest along with a LED-busy
flag to handle concurrency.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 40c24f2893 upstream.
Fix race in device-type detection introduced by commit 0eafe4de ("USB:
serial: mos7840: add support for MCS7810 devices") which used a static
variable to hold the device type.
Move type detection to probe and use serial data to store the device
type.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d8a083cc74 upstream.
Fix race in mos7840_get_reg which unconditionally manipulated the
control urb (which may already be in use) by adding a control-urb busy
flag.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1894870eb4 upstream.
The name of udc state attribute file under sysfs is registered as
"state", while usb_gadget_set_state take it as "status" when it's
going to update. This patch fixes the typo.
Signed-off-by: Rong Wang <Rong.Wang@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fed1f1ed90 upstream.
RT Systems makes many usb serial cables based on the ftdi_sio driver for
programming various amateur radios. This patch is a full listing of
their current product offerings and should allow these cables to all
be recognized.
Signed-off-by: Rick Farina (Zero_Chaos) <zerochaos@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e583d9db99 upstream.
The hub driver was recently changed to use "global" suspend for system
suspend transitions on non-SuperSpeed buses. This means that we don't
suspend devices individually by setting the suspend feature on the
upstream hub port; instead devices all go into suspend automatically
when the root hub stops transmitting packets. The idea was to save
time and to avoid certain kinds of wakeup races.
Now it turns out that many hubs are buggy; they don't relay wakeup
requests from a downstream port to their upstream port if the
downstream port's suspend feature is not set (depending on the speed
of the downstream port, whether or not the hub is enabled for remote
wakeup, and possibly other factors).
We can't have hubs dropping wakeup requests. Therefore this patch
goes partway back to the old policy: It sets the suspend feature for a
port if the device attached to that port or any of its descendants is
enabled for wakeup. People will still be able to benefit from the
time savings if they don't care about wakeup and leave it disabled on
all their devices.
In order to accomplish this, the patch adds a new field to the usb_hub
structure: wakeup_enabled_descendants is a count of how many devices
below a suspended hub are enabled for remote wakeup. A corresponding
new subroutine determines the number of wakeup-enabled devices at or
below an arbitrary suspended USB device.
This should be applied to the 3.10 stable kernel.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: Toralf Förster <toralf.foerster@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2c7b871b91 upstream.
Control transfers have both IN and OUT (or SETUP) packets, so when
clearing TT buffers for a control transfer it's necessary to send
two HUB_CLEAR_TT_BUFFER requests to the hub.
Signed-off-by: William Gulland <wgulland@google.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1fad56424f upstream.
The driver failed to take the dynamic ids into account when determining
the device type and therefore all devices were detected as 2-port
devices when using the dynamic-id interface.
Match on the usb-serial-driver field instead of doing redundant id-table
searches.
Reported-by: Anders Hammarquist <iko@iko.pp.se>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cdcedd6981 upstream.
In case we fail our ->udc_start() callback, we
should be ready to accept another modprobe following
the failed one.
We had forgotten to clear dwc->gadget_driver back
to NULL and, because of that, we were preventing
gadget driver modprobe from being retried.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1974d494de upstream.
Per dwc3 2.50a spec, the is_devspec bit is used to distinguish the
Device Endpoint-Specific Event or Device-Specific Event (DEVT). If the
bit is 1, the event is represented Device-Specific Event, then use
[7:1] bits as Device Specific Event to marked the type. It has 7 bits,
and we can see the reserved8_31 variable name which means from 8 to 31
bits marked reserved, actually there are 24 bits not 25 bits between
that. And 1 + 7 + 24 = 32, the event size is 4 byes.
So in dwc3_event_type, the bit mask should be:
is_devspec [0] 1 bit
type [7:1] 7 bits
reserved8_31 [31:8] 24 bits
This patch should be backported to kernels as old as 3.2, that contain
the commit 72246da40f "usb: Introduce
DesignWare USB3 DRD Driver".
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 315955d707 upstream.
When there is an error with the usb3_phy probe or absence, the error returned
is erroneously for usb2_phy.
Signed-off-by: Ruchika Kharwar <ruchika@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 47a64a13d5 upstream.
Set the ehci->resuming flag for the port we receive a remote
wakeup on so that resume signalling can be completed.
Without this, the root hub timer will not fire again to check
if the resume was completed and there will be a never-ending wait on
on the port.
This effect is only observed if the HUB IRQ IN does not come after we
have initiated the port resume.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 203a86613f upstream.
When the host controller fails to respond to an Enable Slot command, and
the host fails to respond to the register write to abort the command
ring, the xHCI driver will assume the host is dead, and call
usb_hc_died().
The USB device's slot_id is still set to zero, and the pointer stored at
xhci->devs[0] will always be NULL. The call to xhci_check_args in
xhci_free_dev should have caught the NULL virt_dev pointer.
However, xhci_free_dev is designed to free the xhci_virt_device
structures, even if the host is dead, so that we don't leak kernel
memory. xhci_free_dev checks the return value from the generic
xhci_check_args function. If the return value is -ENODEV, it carries on
trying to free the virtual device.
The issue is that xhci_check_args looks at the host controller state
before it looks at the xhci_virt_device pointer. It will return -ENIVAL
because the host is dead, and xhci_free_dev will ignore the return
value, and happily dereference the NULL xhci_virt_device pointer.
The fix is to make sure that xhci_check_args checks the xhci_virt_device
pointer before it checks the host state.
See https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1203453 for
further details. This patch doesn't solve the underlying issue, but
will ensure we don't see any more NULL pointer dereferences because of
the issue.
This patch should be backported to kernels as old as 3.1, that
contain the commit 7bd89b4017 "xhci: Don't
submit commands or URBs to halted hosts."
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: Vincent Thiele <vincentthiele@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d66eaf9f89 upstream.
in some cases where device is attched to xhci port and do not responding,
for example ath9k_htc with stalled firmware, kernel will
crash on ring_doorbell_for_active_rings.
This patch check if pointer exist before it is used.
This patch should be backported to kernels as old as 2.6.35, that
contain the commit e9df17eb14 "USB: xhci:
Correct assumptions about number of rings per endpoint"
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 07f3cb7c28 upstream.
Xhci controllers with hci_version > 0.96 gives spurious success
events on short packet completion. During webcam capture the
"ERROR Transfer event TRB DMA ptr not part of current TD" was observed.
The same application works fine with synopsis controllers hci_version 0.96.
The same issue is seen with Intel Pantherpoint xhci controller. So enabling
this quirk in xhci_gen_setup if controller verion is greater than 0.96.
For xhci-pci move the quirk to much generic place xhci_gen_setup.
Note from Sarah:
The xHCI 1.0 spec changed how hardware handles short packets. The HW
will notify SW of the TRB where the short packet occurred, and it will
also give a successful status for the last TRB in a TD (the one with the
IOC flag set). On the second successful status, that warning will be
triggered in the driver.
Software is now supposed to not assume the TD is not completed until it
gets that last successful status. That means we have a slight race
condition, although it should have little practical impact. This patch
papers over that issue.
It's on my long-term to-do list to fix this race condition, but it is a
much more involved patch that will probably be too big for stable. This
patch is needed for stable to avoid serious log spam.
This patch should be backported to kernels as old as 3.0, that
contain the commit ad808333d8 "Intel xhci:
Ignore spurious successful event."
The patch will have to be modified for kernels older than 3.2, since
that kernel added the xhci_gen_setup function for xhci platform devices.
The correct conflict resolution for kernels older than 3.2 is to set
XHCI_SPURIOUS_SUCCESS in xhci_pci_quirks for all xHCI 1.0 hosts.
Signed-off-by: George Cherian <george.cherian@ti.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b579fa52f6 upstream.
This patch adds support for the Schweitzer Engineering Laboratories
C662 USB cable based off the CP210x driver.
Signed-off-by: Barry Grussling <barry@grussling.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7681156982 upstream.
Added support for MMB Networks and Planet Innovation Ingeni ZigBee USB
devices using customized Silicon Labs' CP210x.c USB to UART bridge
drivers with PIDs: 88A4, 88A5.
Signed-off-by: Sami Rahman <sami.rahman@mmbresearch.com>
Tested-by: Sami Rahman <sami.rahman@mmbresearch.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 90625070c4 upstream.
This adds NetGear Managed Switch M4100 series, M5300 series, M7100 series
USB ID (0846:0110) to the cp210x driver. Without this, the serial
adapter is not recognized in Linux. Description was obtained from
an Netgear Eng.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c38e83b6cc upstream.
This patch was tested on 3.10.1 kernel.
Same models of Petatel NP10T modems have different device IDs.
Unfortunately they have no additional revision information on a board
which may treat them as different devices. Currently I've seen only
two NP10T devices with various IDs. Possibly Petatel NP10T list will
be appended upon devices with new IDs will appear.
Signed-off-by: Daniil Bolsun <dan.bolsun@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 878c69aae9 upstream.
Some (very few) early devices like mine, where not exposting a proper CDC
descriptor. This was fixed with an immediate firmware update from the vendor,
and pre-installed on newer devices.
So actual devices can be driven by cdc_acm.c + cdc_ether.c.
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
