commit 8a487b1a74 upstream.
When the queue is unmapped while it was so loaded that
mac80211's was stopped, we need to wake the queue after
having freed all the packets in the queue.
Not doing so can result in weird stuff like:
* run lots of traffic (mac80211's queue gets stopped)
* RFKILL
* de-assert RFKILL
* no traffic
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b967613d7e upstream.
When a queue is disabled, it frees all its entries. Later,
the op_mode might still get notifications from the firmware
that triggers to free entries in the tx queue. The transport
should be prepared for these races and know to ignore
reclaim calls on queues that have been disabled and whose
entries have been freed.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 10d0b9030a upstream.
A typo causes routine rtl92cu_phy_rf6052_set_cck_txpower() to test the
same condition twice. The problem was found using cppcheck-1.49, and the
proper fix was verified against the pre-mac80211 version of the code.
This patch was originally included as commit 1288aa4, but was accidentally
reverted in a later patch.
Reported-by: David Binderman <dcb314@hotmail.com> [original report]
Reported-by: Andrea Morello <andrea.merello@gmail.com> [report of accidental reversion]
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ath_txq_schedule is called outside of the drv_tx call, so it needs RCU
protection.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
My change:
commit cee2c7315f
Author: Stanislaw Gruszka <sgruszka@redhat.com>
Date: Fri Oct 5 13:44:09 2012 +0200
rt2800: use BBP_R1 for setting tx power
unfortunately does not work well with RT5390 and RT3290 chips as they
require different temperature compensation TX power settings (TSSI
tuning). Since that commit make wireless connection very unstable on
those chips, restore previous behavior to fix regression. Once we
implement proper TSSI tuning on 5390/3290 we can restore back setting
TX power by BBP_R1 register for those chips.
Reported-and-tested-by: Mike Romberg <mike-romberg@comcast.net>
Cc: stable@vger.kernel.org
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a regression introduced by:
commit 6da3b6c48d
Author: Hauke Mehrtens <hauke@hauke-m.de>
Date: Sun Mar 24 01:45:52 2013 +0100
brcmsmac: remove brcms_bss_cfg->associated
The regression behaviour was described on mailing list.
http://mid.gmane.org/5197DC4F.7030503@broadcom.com:
"On laptop I installed kernel with brcmsmac compiled as
module. It comes up and associates during boot, but after
logging in there is no connectivity. Triggering reassoc
gives connectivity for some time, but after a while (1-2 min)
it stops."
Before the mentioned commit the return value of
the function brcms_c_ps_allowed() was always false,
which is desired behaviour as power-save is not
supported at the moment. Therefor, the function is
changed to just return false instead of simply
reverting the mentioned commit.
Bug: 58471 <https://bugzilla.kernel.org/show_bug.cgi?id=58471>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since driver does not use control.rates[0].count, we have never set that
variable. But currently, after rate control API rewrite, this is required
by mac80211. Otherwise legacy rates control does not work and we transmit
always at 1Mbit/s on pre 11n networks.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The module parameter "fwpostfix" is userspace controllable, unfiltered,
and is used to define the firmware filename. b43_do_request_fw() populates
ctx->errors[] on error, containing the firmware filename. b43err()
parses its arguments as a format string. For systems with b43 hardware,
this could lead to a uid-0 to ring-0 escalation.
CVE-2013-2852
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: stable@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Almost all the DMA issues which have plagued ath9k (in station mode)
for years are related to PS. Disabling PS usually "fixes" the user's
connection stablility. Reports of DMA problems are still trickling in
and are sitting in the kernel bugzilla. Until the PS code in ath9k is
given a thorough review, disbale it by default. The slight increase
in chip power consumption is a small price to pay for improved link
stability.
Cc: stable@vger.kernel.org
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This false leak indication is avoided with a no-leak annotation to kmemleak.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Due to a typo, the current code copies only sizeof(cmd->channels_2)
bytes, which is smaller than the correct sizeof(cmd->channels_5)
size, resulting in a partial scan (some channels are skipped).
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The minimum firmware version required for singlerole after recent
driver changes is 6/7.3.10.0.133.
Reported-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There was a typo in commit 8675f9 (wlcore/wl12xx/wl18xx: verify
multi-role and single-role fw versions), which was causing the
multirole firmware for wl127x (WiLink6) to be rejected. The actual
minimum version needed for wl127x multirole is 6.5.7.0.42.
Reported-by: Levi Pearson <levipearson@gmail.com>
Reported-by: Michael Scott <hashcode0f@gmail.com>
Cc: stable@kernel.org # 3.9+
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since driver does not use control.rates[0].count, we have never set that
variable. But currently, after rate control API rewrite, this is required
by mac80211. Otherwise legacy rates control does not work and we transmit
always at 1Mbit/s on pre 11n networks.
[same fix as for iwlegacy, thanks Stanislaw!]
Signed-off-by: Moshe Benji <Moshe.Benji@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
First step of chain noise calibration process had disable flag
check inverted. Chain noise calibration never started because
of this.
Tested on intel 5300 with two antennas attached. The driver
correctly disabled one chain.
Cc: stable@vger.kernel.org
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the opmode modules aren't modular, there's no point in
printing an error message that request_module() failed.
This will happen because the probe runs during iwlwifi's
init and the opmode is only added during its init.
Reported-by: Jörg Otte <jrg.otte@gmail.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For p2p client mode powersave mode should be kept disabled. It is
working but inefficient. In general p2p links do no benefit from this
mode, because these links are setup temporarily to transfer data.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Multi channel support was disabled. This patch will enable it and
configure the P2P GO on the correct frequency when multi channel
is used.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Upon deleting a P2P_CLIENT/GO interface the vif and consequently
the wdev is freed before the net_device is actually being unregistered
but cfg80211 still needs to access the wdev. Using destructor field
to free the net_device and vif.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When registration fails the net device is no longer needed. Free
the net device and remove reference to private data from the
driver.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pass the struct brcmf_cfg80211_info instance instead of obtaining
through vif itself using vif->wdev. This is needed as the netdev
associated with this vif is already unregistered.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The firmware requires that on p2p setup when net interfaces
are created or updated that they start initially with the same
channel as the channel in use for the current connection
(if any). If none exists take default channel 11.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ARP offloading should only be used in STA or P2P client mode. It
is currently configured once at init. When being configured for AP
ARP offloading should be turned off and when AP mode is left it can
be turned back on.
Cc: stable@vger.kernel.org
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR934x v1.3 no longer needs the DCU backoff reduction workaround for
preventing rx overruns, but in turn needs the number of usable Tx
buffers to be reduced slightly.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If a local bus timeout has been detected, the host interface needs to be
reset to clear the errors. AR934x uses a different synchronous interrupt
bit to indicate this, so the check needs to be fixed.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Do not subtract spur power from noise floor on this chip, as it can lead
to packet loss and other connectivity issues.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There was an extra ';' character added to the end of the if statement
which means that it always prints that the /proc entry wasn't created
even though it was.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Waiting for all subframes of an existing aggregation session to drain
before allowing mac80211 to start a new one is fragile and deadlocks
caused by this behavior have been observed.
Since mac80211 has proper synchronization for aggregation session
start/stop handling, a better approach to session handling is to simply
allow mac80211 to start a new session at any time. This requires
changing the code to discard any packets outside of the BlockAck window
in the A-MPDU software retry code.
This patch implements the above and also simplifies the code.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After a tx attempt, an A-MPDU subframe can still have fi->retries at 0
(if the retry count wasn't incremented due to powersave).
In that case it is still tracked as part of the block ack window, so
when draining the tid queue, its sequence number needs to be cleared
from the pending frame bitmap.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes some issues introduced in the rate control API rework.
When not running aggregation, copy bf->rates into info->control.rates
before applying the rate control status to it.
In ath_lookup_rate, the rates need to be pulled from bf->rates, not the
tx info.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When aggregation stop is requested, don't run the mac80211 aggregation
stop callback yet, while the session is still blocked.
Also, when aggregation flush is requested, don't run the callback at all.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Manual peak calibration is currently enabled only for
AR9462 and AR9565. This is also required for AR9485.
The initvals are also modified to disable HW peak calibration.
Cc: <stable@vger.kernel.org>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
P2P_DEVICE support was removed from brcmfmac for v3.9 kernel with
the commit below:
commit 1527c343c1
Author: Arend van Spriel <arend@broadcom.com>
Date: Thu Apr 4 12:10:11 2013 +0200
brcmfmac: remove advertising P2P device support
However, it got merged into wireless-next. But for 3.10 brcmfmac does
support P2P device. Putting it back with this commit.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
