commit b8cb6b4c12 upstream.
If a devices is being recovered it is not InSync and is not Faulty.
If a read error is experienced on that device, fix_read_error()
will be called, but it ignores non-InSync devices. So it will
neither fix the error nor fail the device.
It is incorrect that fix_read_error() ignores non-InSync devices.
It should only ignore Faulty devices. So fix it.
This became a bug when we allowed reading from a device that was being
recovered. It is suitable for any subsequent -stable kernel.
Fixes: da8840a747
Reported-by: Alexander Lyakas <alex.bolshoy@gmail.com>
Tested-by: Alexander Lyakas <alex.bolshoy@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dc99f16f07 upstream.
We can't suspend the PHYs before dwc3_core_exit_mode()
has been called, that's because the host and/or device
sides might still need to communicate with the far end
link partner.
Fixes: 8ba007a (usb: dwc3: core: enable the USB2 and USB3 phy in probe)
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fed33afce0 upstream.
Currently, we disable pm_runtime before all register
accesses are done, this is dangerous and might lead
to abort exceptions due to the driver trying to access
a register which is clocked by a clock which was long
gated.
Fix that by moving pm_runtime_put_sync() and pm_runtime_disable()
as the last thing we do before returning from our ->remove()
method.
Fixes: 72246da (usb: Introduce DesignWare USB3 DRD Driver)
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 96908589a8 upstream.
Commit 71c731a (usb: host: xhci: Fix Compliance Mode
on SN65LVP3502CP Hardware) implemented a workaround
for a known issue with Texas Instruments' USB 3.0
redriver IC but it left a condition where any xHCI
host would be taken out of reset if port was placed
in compliance mode and there was no device connected
to the port.
That condition would trigger a fake connection to a
non-existent device so that usbcore would trigger a
warm reset of the port, thus taking the link out of
reset.
This has the side-effect of preventing any xHCI host
connected to a Linux machine from starting and running
the USB 3.0 Electrical Compliance Suite because the
port will mysteriously taken out of compliance mode
and, thus, xHCI won't step through the necessary
compliance patterns for link validation.
This patch fixes the issue by just adding a missing
check for XHCI_COMP_MODE_QUIRK inside
xhci_hub_report_usb3_link_state() when PORT_CAS isn't
set.
This patch should be backported to all kernels containing
commit 71c731a.
Fixes: 71c731a (usb: host: xhci: Fix Compliance Mode on SN65LVP3502CP Hardware)
Cc: Alexis R. Cortes <alexis.cortes@ti.com>
Cc: <stable@vger.kernel.org> # v3.2+
Signed-off-by: Felipe Balbi <balbi@ti.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c012067961 upstream.
We are getting more and more reports about LG laptops not having
functioning keyboard if we try to deactivate keyboard during probe.
Given that having keyboard deactivated is merely "nice to have"
instead of a hard requirement for probing, let's disable it on all
LG boxes instead of trying to hunt down particular models.
This change is prompted by patches trying to add "LG Electronics"/"ROCKY"
and "LG Electronics"/"LW60-F27B" to the DMI list.
https://bugzilla.kernel.org/show_bug.cgi?id=77051
Reported-by: Jaime Velasco Juan <jsagarribay@gmail.com>
Reported-by: Georgios Tsalikis <georgios@tsalikis.net>
Tested-by: Jaime Velasco Juan <jsagarribay@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5715fc764f upstream.
ForcePads are found on HP EliteBook 1040 laptops. They lack any kind of
physical buttons, instead they generate primary button click when user
presses somewhat hard on the surface of the touchpad. Unfortunately they
also report primary button click whenever there are 2 or more contacts
on the pad, messing up all multi-finger gestures (2-finger scrolling,
multi-finger tapping, etc). To cope with this behavior we introduce a
delay (currently 50 msecs) in reporting primary press in case more
contacts appear.
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a80d8b0275 upstream.
When running a 32-bit inputattach utility in a 64-bit system, there will be
error code "inputattach: can't set device type". This is caused by the
serport device driver not supporting compat_ioctl, so that SPIOCSTYPE ioctl
fails.
Signed-off-by: John Sung <penmount.touch@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d49ec52ff6 upstream.
The DM crypt target accesses memory beyond allocated space resulting in
a crash on 32 bit x86 systems.
This bug is very old (it dates back to 2.6.25 commit 3a7f6c990a "dm
crypt: use async crypto"). However, this bug was masked by the fact
that kmalloc rounds the size up to the next power of two. This bug
wasn't exposed until 3.17-rc1 commit 298a9fa08a ("dm crypt: use per-bio
data"). By switching to using per-bio data there was no longer any
padding beyond the end of a dm-crypt allocated memory block.
To minimize allocation overhead dm-crypt puts several structures into one
block allocated with kmalloc. The block holds struct ablkcipher_request,
cipher-specific scratch pad (crypto_ablkcipher_reqsize(any_tfm(cc))),
struct dm_crypt_request and an initialization vector.
The variable dmreq_start is set to offset of struct dm_crypt_request
within this memory block. dm-crypt allocates the block with this size:
cc->dmreq_start + sizeof(struct dm_crypt_request) + cc->iv_size.
When accessing the initialization vector, dm-crypt uses the function
iv_of_dmreq, which performs this calculation: ALIGN((unsigned long)(dmreq
+ 1), crypto_ablkcipher_alignmask(any_tfm(cc)) + 1).
dm-crypt allocated "cc->iv_size" bytes beyond the end of dm_crypt_request
structure. However, when dm-crypt accesses the initialization vector, it
takes a pointer to the end of dm_crypt_request, aligns it, and then uses
it as the initialization vector. If the end of dm_crypt_request is not
aligned on a crypto_ablkcipher_alignmask(any_tfm(cc)) boundary the
alignment causes the initialization vector to point beyond the allocated
space.
Fix this bug by calculating the variable iv_size_padding and adding it
to the allocated size.
Also correct the alignment of dm_crypt_request. struct dm_crypt_request
is specific to dm-crypt (it isn't used by the crypto subsystem at all),
so it is aligned on __alignof__(struct dm_crypt_request).
Also align per_bio_data_size on ARCH_KMALLOC_MINALIGN, so that it is
aligned as if the block was allocated with kmalloc.
Reported-by: Krzysztof Kolasa <kkolasa@winsoft.pl>
Tested-by: Milan Broz <gmazyland@gmail.com>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d07f1e8600 upstream.
Smatch says that skb->data is untrusted so we need to check to make sure
that the memcpy() doesn't overflow.
Fixes: cfad1ba871 ('NFC: Initial support for Inside Secure microread')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b53b0d99d6 upstream.
This patch fixes a bug in iscsit_logout_post_handler_diffcid() where
a pointer used as storage for list_for_each_entry() was incorrectly
being used to determine if no matching entry had been found.
This patch changes iscsit_logout_post_handler_diffcid() to key off
bool conn_found to determine if the function needs to exit early.
Reported-by: Joern Engel <joern@logfs.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8ae757d09c upstream.
In iscsi_copy_param_list() a failed iscsi_param_list memory allocation
currently invokes iscsi_release_param_list() to cleanup, and will promptly
trigger a NULL pointer dereference.
Instead, go ahead and return for the first iscsi_copy_param_list()
failure case.
Found by coverity.
Signed-off-by: Joern Engel <joern@logfs.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0fc4ea701f upstream.
disconnected_handler is invoked on several CM events (such
as DISCONNECTED, DEVICE_REMOVAL, TIMEWAIT_EXIT...). Since
multiple events can occur while before isert_free_conn is
invoked, we might put all isert_conn references and free
the connection too early.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c2f88b17a1 upstream.
In case the connection didn't reach connected state, disconnected
handler will never be invoked thus the second kref_put on
isert_conn will be missing.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a31d092899 upstream.
This patch fix gains values. The first driver was designed using
engineering samples, in mass production the values are changed.
Signed-off-by: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5844a8b9d9 upstream.
A previous over-zealous factorisation of code means that we only treat
registers as volatile if they are readable. For most devices this is fine
since normally most registers can be read and volatility implies
readability but for format_write() devices where there is no readback from
the hardware and we use volatility to mean simply uncacheability this means
that we end up treating all registers as cacheble.
A bigger refactoring of the code to clarify this is in order but as a fix
make a minimal change and only check readability when checking volatility
if there is no format_write() operation defined for the device.
Signed-off-by: Mark Brown <broonie@linaro.org>
Tested-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 75ec6e55f1 upstream.
Changes to correct several GPIO issues:
1) The update_rule in a GPIO field definition is now ignored;
a read-modify-write operation is never performed for GPIO fields.
(Internally, this means that the field assembly/disassembly
code is completely bypassed for GPIO.)
2) The Address parameter passed to a GPIO region handler is
now the bit offset of the field from a previous Connection()
operator. Thus, it becomes a "Pin Number Index" into the
Connection() resource descriptor.
3) The bit_width parameter passed to a GPIO region handler is
now the exact bit width of the GPIO field. Thus, it can be
interpreted as "number of pins".
Overall, we can now say that the region handler interface
to GPIO handlers is a raw "bit/pin" addressed interface, not
a byte-addressed interface like the system_memory handler interface.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 08d1dec6f4 upstream.
When we are doing compliance test with xHCI, we found that if we
enable CONFIG_USB_SUSPEND and plug in a bad device which causes
over-current condition to the root port, software will not be noticed.
The reason is that current code don't set hub->change_bits in
hub_activate() when over-current happens, and then hub_events() will
not check the port status because it thinks nothing changed.
If CONFIG_USB_SUSPEND is disabled, the interrupt pipe of the hub will
report the change and set hub->event_bits, and then hub_events() will
check what events happened.In this case over-current can be detected.
Signed-off-by: Shen Guang <shenguang10@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 81a60b7f5c upstream.
we don't to gate clocks until our children are
done with their remove path.
Fixes: af310e9 (usb: dwc3: omap: use runtime API's to enable clocks)
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7312b5ddd4 upstream.
Old code in ehci-hcd tries to expedite disabling endpoints after the
controller has stopped, by destroying the endpoint's associated QH
without first unlinking the QH. This was necessary back when the
driver wasn't so careful about keeping track of the controller's
state.
But now we are careful about it, and the driver knows that when the
controller isn't running, no unlinking delay is needed. Furthermore,
skipping the unlink step will trigger a BUG() in qh_destroy() when the
preceding QH is released, because the link pointer will be non-NULL.
Removing the lines that skip the unlinking step and go directly to
QH_STATE_IDLE fixes the problem.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Joe Lawrence <joe.lawrence@stratus.com>
Tested-by: Joe Lawrence <joe.lawrence@stratus.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c80b4495c6 upstream.
This patch adds quirks for Entrega Technologies (later Xircom PortGear) USB-
SCSI converters. They use Shuttle Technology EUSB-01/EUSB-S1 chips. The
US_FL_SCM_MULT_TARG quirk is needed to allow multiple devices on the SCSI
chain to be accessed. Without it only the (single) device with SCSI ID 0
can be used.
The standalone converter sold by Entrega had model number U1-SC25. Xircom
acquired Entrega and re-branded the product line PortGear. The PortGear USB
to SCSI Converter (model PGSCSI) is internally identical to the Entrega
product, but later models may use a different USB ID. The Entrega-branded
units have USB ID 1645:0007, as does my Xircom PGSCSI, but the Windows and
Macintosh drivers also support 085A:0028.
Entrega also sold the "Mac USB Dock", which provides two USB ports, a Mac
(8-pin mini-DIN) serial port and a SCSI port. It appears to the computer as
a four-port hub, USB-serial, and USB-SCSI converters. The USB-SCSI part may
have initially used the same ID as the standalone U1-SC25 (1645:0007), but
later production used 085A:0026.
My Xircom PortGear PGSCSI has bcdDevice=0x0100. Units with bcdDevice=0x0133
probably also exist.
This patch adds quirks for 1645:0007, 085A:0026 and 085A:0028. The Windows
driver INF file also mentions 085A:0032 "PortStation SCSI Module", but I
couldn't find any mention of that actually existing in the wild; perhaps it
was cancelled before release?
Signed-off-by: Mark Knibbs <markk@clara.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b6a3ed6779 upstream.
Hi,
The Ariston Technologies iConnect 025 and iConnect 050 (also known as e.g.
iSCSI-50) are SCSI-USB converters which use Shuttle Technology/SCM
Microsystems chips. Only the connectors differ; both have the same USB ID.
The US_FL_SCM_MULT_TARG quirk is required to use SCSI devices with ID other
than 0.
I don't have one of these, but based on the other entries for Shuttle/
SCM-based converters this patch is very likely correct. I used 0x0000 and
0x9999 for bcdDeviceMin and bcdDeviceMax because I'm not sure which
bcdDevice value the products use.
Signed-off-by: Mark Knibbs <markk@clara.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 67d365a57a upstream.
The Adaptec USBConnect 2000 is another SCSI-USB converter which uses
Shuttle Technology/SCM Microsystems chips. The US_FL_SCM_MULT_TARG quirk is
required to use SCSI devices with ID other than 0.
I don't have a USBConnect 2000, but based on the other entries for Shuttle/
SCM-based converters this patch is very likely correct. I used 0x0000 and
0x9999 for bcdDeviceMin and bcdDeviceMax because I'm not sure which
bcdDevice value the product uses.
Signed-off-by: Mark Knibbs <markk@clara.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c66f1c62e8 upstream.
The Iomega Jaz USB Adapter is a SCSI-USB converter cable. The hardware
seems to be identical to e.g. the Microtech XpressSCSI, using a Shuttle/
SCM chip set. However its firmware restricts it to only work with Jaz
drives.
On connecting the cable a message like this appears four times in the log:
reset full speed USB device number 4 using uhci_hcd
That's non-fatal but the US_FL_SINGLE_LUN quirk fixes it.
Signed-off-by: Mark Knibbs <markk@clara.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c605f3cdff upstream.
During surprise device hotplug removal tests, it was observed that
hub_events may try to call usb_lock_device on a device that has already
been freed. Protect the usb_device by taking out a reference (under the
hub_event_lock) when hub_events pulls it off the list, returning the
reference after hub_events is finished using it.
Signed-off-by: Joe Lawrence <joe.lawrence@stratus.com>
Suggested-by: David Bulkow <david.bulkow@stratus.com> for using kref
Suggested-by: Alan Stern <stern@rowland.harvard.edu> for placement
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 96044694b8 upstream.
Resuming from hibernate (S4) will restart and re-initialize xHC.
The device contexts are freed and will be re-allocated later during device reset.
Usb core will disable link pm in device resume before device reset, which will
try to change the max exit latency, accessing the device contexts before they are re-allocated.
There is no need to zero (disable) the max exit latency when disabling hw lpm
for a freshly re-initialized xHC. So check that device context exists before
doing anything. The max exit latency will be set again after device reset when usb core
enables the link pm.
Reported-by: Imre Deak <imre.deak@intel.com>
Tested-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c207e7c50f upstream.
If xhci initialization fails before the roothub bandwidth
domains (xhci->rh_bw[i]) are allocated it will oops when
trying to access rh_bw members in xhci_mem_cleanup().
Reported-by: Manuel Reimer <manuel.reimer@gmx.de>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3096691011 upstream.
Add back some PIDs that were mistakingly remove when reverting commit
73228a0538 ("USB: option,zte_ev: move most ZTE CDMA devices to
zte_ev"), which apparently did more than its commit message claimed in
that it not only moved some PIDs from option to zte_ev but also added
some new ones.
Fixes: 63a901c06e ("Revert "USB: option,zte_ev: move most ZTE CDMA
devices to zte_ev"")
Reported-by: Lei Liu <lei35151@163.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5b3da69285 upstream.
This VID:PID is used for some Direct IP devices behaving
identical to the already supported 0F3D:68AA devices.
Reported-by: Lars Melin <larsm17@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 049255f516 upstream.
Sierra Wireless Direct IP devices using the 68A3 product ID
can be configured for modes including a CDC ECM class function.
The known example uses interface numbers 12 and 13 for the ECM
control and data interfaces respectively, consistent with CDC
MBIM function interface numbering on other Sierra devices.
It seems cleaner to restrict this driver to the ff/ff/ff
vendor specific interfaces rather than increasing the already
long interface number blacklist. This should be more future
proof if Sierra adds more class functions using interface
numbers not yet in the blacklist.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 754eb21c0b upstream.
Remove dublicate Qualcom PID 0x3197 which is already handled by the
moto-modem driver since commit 6986a978ee ("USB: add new moto_modem
driver for some Morotola phones").
Fixes: 799ee9243d ("USB: serial: add zte_ev.c driver")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 63a901c06e upstream.
This reverts commit 73228a0538 ("USB: option,zte_ev: move most ZTE
CDMA devices to zte_ev").
Move the IDs of the devices that were previously driven by the option
driver back to that driver.
As several users have reported, the zte_ev driver is causing random
disconnects as well as reconnect failures.
A closer analysis of the zte_ev setup code reveals that it consists of
standard CDC requests (SET/GET_LINE_CODING and SET_CONTROL_LINE_STATE)
but unfortunately fails to get some of those right. In particular, as
reported by Liu Lei, it fails to lower DTR/RTS on close. It also appears
that the control requests lack the interface argument.
Note that the zte_ev driver is based on code (once) distributed by ZTE
that still appears to originally have been reverse-engineered and bolted
onto the generic driver.
Since line control is already handled properly by the option driver, and
the SET/GET_LINE_CODING requests appears to be redundant (amounts to a
SET 9600 8N1), this is a first step in ultimately removing the redundant
zte_ev driver.
Note that AC2726 had already been moved back to option, and that some
IDs were in the device table of both drivers prior to the commit being
reverted.
Reported-by: Lei Liu <liu.lei78@zte.com.cn>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d77302739d upstream.
This VIA Telecom baseband processor is used is used by by u-blox in both the
FW2770 and FW2760 products and may be used in others as well.
This patch has been tested on both of these modem versions.
Signed-off-by: Brennan Ashton <bashton@brennanashton.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f0e4cba253 upstream.
Do not log normal interrupt-urb shutdowns as errors.
The option driver has always been logging any nonzero interrupt-urb
status as an error, including when the urb is killed during normal
operation.
Commit 9096f1fbba ("USB: usb_wwan: fix potential NULL-deref at
resume") moved the interrupt urb submission from port probe and release
to open and close, thus potentially increasing the number of these
false-positive error messages dramatically.
Reported-by: Ed Butler <ressy66@ausics.net>
Tested-by: Ed Butler <ressy66@ausics.net>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
