commit c319d50bfc upstream.
This is similar to the race Linus had reported, but in this case
it's an older bug: nl80211_prepare_wdev_dump() uses the wiphy
index in cb->args[0] as it is and thus parses the message over
and over again instead of just once because 0 is the first valid
wiphy index. Similar code in nl80211_testmode_dump() correctly
offsets the wiphy_index by 1, do that here as well.
Reported-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 74418edec9 upstream.
When a P2P GO interface goes down, cfg80211 doesn't properly
tear it down, leading to warnings later. Add the GO interface
type to the enumeration to tear it down like AP interfaces.
Otherwise, we leave it pending and mac80211's state can get
very confused, leading to warnings later.
Reported-by: Ilan Peer <ilan.peer@intel.com>
Tested-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 58ad436fcf upstream.
When dumping generic netlink families, only the first dump call
is locked with genl_lock(), which protects the list of families,
and thus subsequent calls can access the data without locking,
racing against family addition/removal. This can cause a crash.
Fix it - the locking needs to be conditional because the first
time around it's already locked.
A similar bug was reported to me on an old kernel (3.4.47) but
the exact scenario that happened there is no longer possible,
on those kernels the first round wasn't locked either. Looking
at the current code I found the race described above, which had
also existed on the old kernel.
Reported-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ddfe49b42d upstream.
In case the AP has different regulatory information than we do,
it can happen that we connect to an AP based on e.g. the world
roaming regulatory data, and then update our database with the
AP's country information disables the channel the AP is using.
If this happens on an HT AP, the bandwidth tracking code will
hit the WARN_ON() and disconnect. Since that's not very useful,
ignore the channel-disable flag in bandwidth tracking.
Reported-by: Chris Wright <chrisw@sous-sol.org>
Tested-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b56e4b857c upstream.
Commit "3d9646d mac80211: fix channel selection bug" introduced a possible
infinite loop by moving the out target above the chandef_downgrade
while loop. When we downgrade to NL80211_CHAN_WIDTH_20_NOHT, we jump
back up to re-run the while loop...indefinitely. Replace goto with
break and carry on. This may not be sufficient to connect to the AP,
but will at least keep the cpu from livelocking. Thanks to Derek Atkins
as an extra pair of debugging eyes.
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5cdaed1e87 upstream.
While we're connected, the AP shouldn't change the primary channel
in the HT information. We checked this, and dropped the connection
if it did change it.
Unfortunately, this is causing problems on some APs, e.g. on the
Netgear WRT610NL: the beacons seem to always contain a bad channel
and if we made a connection using a probe response (correct data)
we drop the connection immediately and can basically not connect
properly at all.
Work around this by ignoring the HT primary channel information in
beacons if we're already connected.
Also print out more verbose messages in the other situations to
help diagnose similar bugs quicker in the future.
Acked-by: Andy Isaacson <adi@hexapodia.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 786615bc1c upstream.
If rpcbind causes our connection to the AF_LOCAL socket to close after
we've registered a service, then we want to be careful about reconnecting
since the mount namespace may have changed.
By simply refusing to reconnect the AF_LOCAL socket in the case of
unregister, we avoid the need to somehow save the mount namespace. While
this may lead to some services not unregistering properly, it should
be safe.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Cc: Nix <nix@esperi.org.uk>
Cc: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 00326ed644 upstream.
There is no need for the kernel to time out the AF_LOCAL connection to
the rpcbind socket, and doing so is problematic because when it is
time to reconnect, our process may no longer be using the same mount
namespace.
Reported-by: Nix <nix@esperi.org.uk>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Cc: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a0db856a95 ]
Make sure the reserved fields, and padding (if any), are
fully initialized.
Based upon a patch by Dan Carpenter and feedback from
Joe Perches.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dc43376c26 upstream.
Uninitialized stack data was being used as the destination for memcpy's.
Longer term we'll just delete some of this code; all we're doing is
skipping over xdr that we don't care about.
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e13bae4f80 upstream.
As reported in https://bugzilla.kernel.org/show_bug.cgi?id=60514,
the station loop never initialises 'sinfo' and therefore adds up
a stack values, leaking stack information (the number of times it
adds values is easily obtained another way.)
Fix this by initialising the sinfo for each station to add.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6b0f32745d upstream.
The duplicate retransmission detection code in mac80211
erroneously attempts to do the check for every frame,
even frames that don't have a sequence control field or
that don't use it (QoS-Null frames.)
This is problematic because it causes the code to access
data beyond the end of the SKB and depending on the data
there will drop packets erroneously.
Correct the code to not do duplicate detection for such
frames.
I found this error while testing AP powersave, it lead
to retransmitted PS-Poll frames being dropped entirely
as the data beyond the end of the SKB was always zero.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1cd1585739 upstream.
The CCK group needs special treatment to set the right flags and rate
index. Add this missing check to prevent setting broken rates for tx
packets.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5c9fc93bc9 upstream.
When priv_sta == NULL, mi->prev_sample is dereferenced too early. Move
the assignment further down, after the rate_control_send_low call.
Reported-by: Krzysztof Mazur <krzysiek@podlesie.net>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a0ec570f4f upstream.
These two events were sent to the default network
namespace.
This caused AP mode in a non-default netns to not
work correctly. Mgmt tx status was multicasted to
a different (default) netns instead of the one the
AP was in.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b2781e1021 upstream.
My static checker marks everything from ntohl() as untrusted and it
complains we could have an underflow problem doing:
return (u32 *)&ary->wc_array[nchunks];
Also on 32 bit systems the upper bound check could overflow.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3e3aac4975 ]
egress_priority_map[] hash table updates are protected by rtnl,
and we never remove elements until device is dismantled.
We have to make sure that before inserting an new element in hash table,
all its fields are committed to memory or else another cpu could
find corrupt values and crash.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d4b812dea4 ]
In commit 48cc32d38a
("vlan: don't deliver frames for unknown vlans to protocols")
Florian made sure we set pkt_type to PACKET_OTHERHOST
if the vlan id is set and we could find a vlan device for this
particular id.
But we also have a problem if prio bits are set.
Steinar reported an issue on a router receiving IPv6 frames with a
vlan tag of 4000 (id 0, prio 2), and tunneled into a sit device,
because skb->vlan_tci is set.
Forwarded frame is completely corrupted : We can see (8100:4000)
being inserted in the middle of IPv6 source address :
16:48:00.780413 IP6 2001:16d8:8100:4000:ee1c:0:9d9:bc87 >
9f94:4d95:2001:67c:29f4::: ICMP6, unknown icmp6 type (0), length 64
0x0000: 0000 0029 8000 c7c3 7103 0001 a0ae e651
0x0010: 0000 0000 ccce 0b00 0000 0000 1011 1213
0x0020: 1415 1617 1819 1a1b 1c1d 1e1f 2021 2223
0x0030: 2425 2627 2829 2a2b 2c2d 2e2f 3031 3233
It seems we are not really ready to properly cope with this right now.
We can probably do better in future kernels :
vlan_get_ingress_priority() should be a netdev property instead of
a per vlan_dev one.
For stable kernels, lets clear vlan_tci to fix the bugs.
Reported-by: Steinar H. Gunderson <sesse@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 87f40dd6ce ]
QFQ+ inherits from QFQ a design choice that may cause a high packet
delay/jitter and a severe short-term unfairness. As QFQ, QFQ+ uses a
special quantity, the system virtual time, to track the service
provided by the ideal system it approximates. When a packet is
dequeued, this quantity must be incremented by the size of the packet,
divided by the sum of the weights of the aggregates waiting to be
served. Tracking this sum correctly is a non-trivial task, because, to
preserve tight service guarantees, the decrement of this sum must be
delayed in a special way [1]: this sum can be decremented only after
that its value would decrease also in the ideal system approximated by
QFQ+. For efficiency, QFQ+ keeps track only of the 'instantaneous'
weight sum, increased and decreased immediately as the weight of an
aggregate changes, and as an aggregate is created or destroyed (which,
in its turn, happens as a consequence of some class being
created/destroyed/changed). However, to avoid the problems caused to
service guarantees by these immediate decreases, QFQ+ increments the
system virtual time using the maximum value allowed for the weight
sum, 2^10, in place of the dynamic, instantaneous value. The
instantaneous value of the weight sum is used only to check whether a
request of weight increase or a class creation can be satisfied.
Unfortunately, the problems caused by this choice are worse than the
temporary degradation of the service guarantees that may occur, when a
class is changed or destroyed, if the instantaneous value of the
weight sum was used to update the system virtual time. In fact, the
fraction of the link bandwidth guaranteed by QFQ+ to each aggregate is
equal to the ratio between the weight of the aggregate and the sum of
the weights of the competing aggregates. The packet delay guaranteed
to the aggregate is instead inversely proportional to the guaranteed
bandwidth. By using the maximum possible value, and not the actual
value of the weight sum, QFQ+ provides each aggregate with the worst
possible service guarantees, and not with service guarantees related
to the actual set of competing aggregates. To see the consequences of
this fact, consider the following simple example.
Suppose that only the following aggregates are backlogged, i.e., that
only the classes in the following aggregates have packets to transmit:
one aggregate with weight 10, say A, and ten aggregates with weight 1,
say B1, B2, ..., B10. In particular, suppose that these aggregates are
always backlogged. Given the weight distribution, the smoothest and
fairest service order would be:
A B1 A B2 A B3 A B4 A B5 A B6 A B7 A B8 A B9 A B10 A B1 A B2 ...
QFQ+ would provide exactly this optimal service if it used the actual
value for the weight sum instead of the maximum possible value, i.e.,
11 instead of 2^10. In contrast, since QFQ+ uses the latter value, it
serves aggregates as follows (easy to prove and to reproduce
experimentally):
A B1 B2 B3 B4 B5 B6 B7 B8 B9 B10 A A A A A A A A A A B1 B2 ... B10 A A ...
By replacing 10 with N in the above example, and by increasing N, one
can increase at will the maximum packet delay and the jitter
experienced by the classes in aggregate A.
This patch addresses this issue by just using the above
'instantaneous' value of the weight sum, instead of the maximum
possible value, when updating the system virtual time. After the
instantaneous weight sum is decreased, QFQ+ may deviate from the ideal
service for a time interval in the order of the time to serve one
maximum-size packet for each backlogged class. The worst-case extent
of the deviation exhibited by QFQ+ during this time interval [1] is
basically the same as of the deviation described above (but, without
this patch, QFQ+ suffers from such a deviation all the time). Finally,
this patch modifies the comment to the function qfq_slot_insert, to
make it coherent with the fact that the weight sum used by QFQ+ can
now be lower than the maximum possible value.
[1] P. Valente, "Extending WF2Q+ to support a dynamic traffic mix",
Proceedings of AAA-IDEA'05, June 2005.
Signed-off-by: Paolo Valente <paolo.valente@unimore.it>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 21d1196a35 ]
commit 45f00f99d6 ("ipv4: tcp: clean up tcp_v4_early_demux()") added a
performance regression for non GRO traffic, basically disabling
IP early demux.
IPv6 stack resets transport header in ip6_rcv() before calling
IP early demux in ip6_rcv_finish(), while IPv4 does this only in
ip_local_deliver_finish(), _after_ IP early demux.
GRO traffic happened to enable IP early demux because transport header
is also set in inet_gro_receive()
Instead of reverting the faulty commit, we can make IPv4/IPv6 behave the
same : transport_header should be set in ip_rcv() instead of
ip_local_deliver_finish()
ip_local_deliver_finish() can also use skb_network_header_len() which is
faster than ip_hdrlen()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 307f2fb95e ]
Static routes in this case are non-expiring routes which did not get
configured by autoconf or by icmpv6 redirects.
To make sure we actually get an ecmp route while searching for the first
one in this fib6_node's leafs, also make sure it matches the ecmp route
assumptions.
v2:
a) Removed RTF_EXPIRE check in dst.from chain. The check of RTF_ADDRCONF
already ensures that this route, even if added again without
RTF_EXPIRES (in case of a RA announcement with infinite timeout),
does not cause the rt6i_nsiblings logic to go wrong if a later RA
updates the expiration time later.
v3:
a) Allow RTF_EXPIRES routes to enter the ecmp route set. We have to do so,
because an pmtu event could update the RTF_EXPIRES flag and we would
not count this route, if another route joins this set. We now filter
only for RTF_GATEWAY|RTF_ADDRCONF|RTF_DYNAMIC, which are flags that
don't get changed after rt6_info construction.
Cc: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8c91e162e0 ]
This change fixes an MTU sizing issue seen with gretap tunnels when non-gso
packets are sent from the interface.
In my case I was able to reproduce the issue by simply sending a ping of
1421 bytes with the gretap interface created on a device with a standard
1500 mtu.
This fix is based on the fact that the tunnel mtu is already adjusted by
dev->hard_header_len so it would make sense that any packets being compared
against that mtu should also be adjusted by hard_header_len and the tunnel
header instead of just the tunnel header.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Reported-by: Cong Wang <amwang@redhat.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit afc154e978 ]
This is a follow-up patch to 3630d40067
("ipv6: rt6_check_neigh should successfully verify neigh if no NUD
information are available").
Since the removal of rt->n in rt6_info we can end up with a dst ==
NULL in rt6_check_neigh. In case the kernel is not compiled with
CONFIG_IPV6_ROUTER_PREF we should also select a route with unkown
NUD state but we must not avoid doing round robin selection on routes
with the same target. So introduce and pass down a boolean ``do_rr'' to
indicate when we should update rt->rr_ptr. As soon as no route is valid
we do backtracking and do a lookup on a higher level in the fib trie.
v2:
a) Improved rt6_check_neigh logic (no need to create neighbour there)
and documented return values.
v3:
a) Introduce enum rt6_nud_state to get rid of the magic numbers
(thanks to David Miller).
b) Update and shorten commit message a bit to actualy reflect
the source.
Reported-by: Pierre Emeriaud <petrus.lt@gmail.com>
Cc: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3630d40067 ]
After the removal of rt->n we do not create a neighbour entry at route
insertion time (rt6_bind_neighbour is gone). As long as no neighbour is
created because of "useful traffic" we skip this routing entry because
rt6_check_neigh cannot pick up a valid neighbour (neigh == NULL) and
thus returns false.
This change was introduced by commit
887c95cc1d ("ipv6: Complete neighbour
entry removal from dst_entry.")
To quote RFC4191:
"If the host has no information about the router's reachability, then
the host assumes the router is reachable."
and also:
"A host MUST NOT probe a router's reachability in the absence of useful
traffic that the host would have sent to the router if it were reachable."
So, just assume the router is reachable and let's rt6_probe do the
rest. We don't need to create a neighbour on route insertion time.
If we don't compile with CONFIG_IPV6_ROUTER_PREF (RFC4191 support)
a neighbour is only valid if its nud_state is NUD_VALID. I did not find
any references that we should probe the router on route insertion time
via the other RFCs. So skip this route in that case.
v2:
a) use IS_ENABLED instead of #ifdefs (thanks to Sergei Shtylyov)
Reported-by: Pierre Emeriaud <petrus.lt@gmail.com>
Cc: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3b7b514f44 ]
This is a regression introduced by
commit fd58156e45 (IPIP: Use ip-tunneling code.)
Similar to GRE tunnel, previously we only check the parameters
for SIOCADDTUNNEL and SIOCCHGTUNNEL, after that commit, the
check is moved for all commands.
So, just check for SIOCADDTUNNEL and SIOCCHGTUNNEL.
Also, the check for i_key, o_key etc. is suspicious too,
which did not exist before, reset them before passing
to ip_tunnel_ioctl().
Signed-off-by: Cong Wang <amwang@redhat.com>
Cc: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 23a3647bc4 ]
In path mtu check, ip header total length works for gre device
but not for gre-tap device. Use skb len which is consistent
for all tunneling types. This is old bug in gre.
This also fixes mtu calculation bug introduced by
commit c544193214 (GRE: Refactor GRE tunneling code).
Reported-by: Timo Teras <timo.teras@iki.fi>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6c734fb859 ]
When testing GRE tunnel, I got:
# ip tunnel show
get tunnel gre0 failed: Invalid argument
get tunnel gre1 failed: Invalid argument
This is a regression introduced by commit c544193214
("GRE: Refactor GRE tunneling code.") because previously we
only check the parameters for SIOCADDTUNNEL and SIOCCHGTUNNEL,
after that commit, the check is moved for all commands.
So, just check for SIOCADDTUNNEL and SIOCCHGTUNNEL.
After this patch I got:
# ip tunnel show
gre0: gre/ip remote any local any ttl inherit nopmtudisc
gre1: gre/ip remote 192.168.122.101 local 192.168.122.45 ttl inherit
Signed-off-by: Cong Wang <amwang@redhat.com>
Cc: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4ccb93ce74 ]
Two of the x25 ioctl cases have error paths that break out of the function without
unlocking the socket, leading to this warning:
================================================
[ BUG: lock held when returning to user space! ]
3.10.0-rc7+ #36 Not tainted
------------------------------------------------
trinity-child2/31407 is leaving the kernel with locks still held!
1 lock held by trinity-child2/31407:
#0: (sk_lock-AF_X25){+.+.+.}, at: [<ffffffffa024b6da>] x25_ioctl+0x8a/0x740 [x25]
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c9ab4d85de ]
There is a race in neighbour code, because neigh_destroy() uses
skb_queue_purge(&neigh->arp_queue) without holding neighbour lock,
while other parts of the code assume neighbour rwlock is what
protects arp_queue
Convert all skb_queue_purge() calls to the __skb_queue_purge() variant
Use __skb_queue_head_init() instead of skb_queue_head_init()
to make clear we do not use arp_queue.lock
And hold neigh->lock in neigh_destroy() to close the race.
Reported-by: Joe Jin <joe.jin@oracle.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5c29fb12e8 ]
Because of commit 218774dc34 ("ipv6: add
anti-spoofing checks for 6to4 and 6rd") the sit driver dropped packets
for 2002::/16 destinations and sources even when configured to work as a
tunnel with fixed endpoint. We may only apply the 6rd/6to4 anti-spoofing
checks if the device is not in pointopoint mode.
This was an oversight from me in the above commit, sorry. Thanks to
Roman Mamedov for reporting this!
Reported-by: Roman Mamedov <rm@romanrm.ru>
Cc: David Miller <davem@davemloft.net>
Cc: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1f691b07c5 upstream.
Though clients we care about mostly don't do this, it is possible for
rpc requests to be sent in multiple fragments. Here we have a sanity
check to ensure that the final received rpc isn't too small--except that
the number we're actually checking is the length of just the final
fragment, not of the whole rpc. So a perfectly legal rpc that's
unluckily fragmented could cause the server to close the connection
here.
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cf3aa02cb4 upstream.
If we detect that an rpc is too short, we abort and close the
connection. Except, there's a bug here: we're leaving sk_datalen
nonzero without leaving any pages in the sk_pages array. The most
likely result of the inconsistency is a subsequent crash in
svc_tcp_clear_pages.
Also demote the BUG_ON in svc_tcp_clear_pages to a WARN.
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0979292bfa upstream.
As of f025adf191 "sunrpc: Properly decode
kuids and kgids in RPC_AUTH_UNIX credentials" any rpc containing a -1
(0xffff) uid or gid would fail with a badcred error.
Commit afe3c3fd53 "svcrpc: fix failures to
handle -1 uid's and gid's" fixed part of the problem, but overlooked the
gid upcall--the kernel can request supplementary gid's for the -1 uid,
but mountd's attempt write a response will get -EINVAL.
Symptoms were nfsd failing to reply to the first attempt to use a newly
negotiated krb5 context.
Reported-by: Sven Geggus <lists@fuchsschwanzdomain.de>
Tested-by: Sven Geggus <lists@fuchsschwanzdomain.de>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4c8a9d4bfa upstream.
Since Eric's commit efe117ab8 ("Speedup ieee80211_remove_interfaces")
there's a bug in mac80211 when it unregisters with AP_VLAN interfaces
up. If the AP_VLAN interface was registered after the AP it belongs
to (which is the typical case) and then we get into this code path,
unregister_netdevice_many() will crash because it isn't prepared to
deal with interfaces being closed in the middle of it. Exactly this
happens though, because we iterate the list, find the AP master this
AP_VLAN belongs to and dev_close() the dependent VLANs. After this,
unregister_netdevice_many() won't pick up the fact that the AP_VLAN
is already down and will do it again, causing a crash.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2cb33cac62 upstream.
A malicious monitor can craft an auth reply message that could cause a
NULL function pointer dereference in the client's kernel.
To prevent this, the auth_none protocol handler needs an empty
ceph_auth_client_ops->build_request() function.
CVE-2013-1059
Signed-off-by: Tyler Hicks <tyhicks@canonical.com>
Reported-by: Chanam Park <chanam.park@hkpco.kr>
Reviewed-by: Seth Arnold <seth.arnold@canonical.com>
Reviewed-by: Sage Weil <sage@inktank.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
