This adds a driver for reading the battery status of the
battery connected to the Atmel microcontroller on the
iPAQ h3xxx series.
Based on a driver from handhelds.org 2.6.21 kernel, written
by Alessandro GARDICH.
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
TWL4030's Battery Charger seems to be designed for non-hotpluggable
batteries.
If battery is not present in the system, BATSTS is always set with the
expectation that software will take actions to move to a required safe
state (could be power down or disable various charger paths).
It does not seem possible even by manipulating the edge detection
of the event (using BCIEDR2 register) to have a consistent hotplug
handling. This seems to be the result of BATSTS interrupt generated
when the thermistor of the battery pack is disconnected from the
dedicated ADIN1 pin. Clearing the status just results in the status
being regenerated by the monitoring ADC(MADC) and disabling the
edges of event just makes hotplug no longer function. The only
other option is to disable the detection of the MADC by disabling
BCIMFEN4::BATSTSMCHGEN (battery presence detector) - but then, we can
never again detect battery reconnection.
So, detect battery presence based on precharge(which is hardware
automatic state) or default main charger configuration at the time of
probe and enable charger logic only if battery was present.
Reported-by: Russell King <linux@arm.linux.org.uk>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Add support for reboot functionality on boards with ARM-based
Broadcom STB chipsets. Make it built-in by default for ARCH_BRCMSTB,
but allow it to be configurable under COMPILE_TEST.
Signed-off-by: Marc Carino <marc.ceeeee@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Fixes the following sparse warnings:
drivers/power/power_supply_core.c:540:5: warning:
symbol '__power_supply_register' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Add new power supply properties for input current, charge termination
current, min and max temperature
POWER_SUPPLY_PROP_TEMP_MIN - minimum operatable temperature
POWER_SUPPLY_PROP_TEMP_MAX - maximum operatable temperature
POWER_SUPPLY_PROP_INPUT_CURRENT_LIMIT - input current limit programmed
by charger. Indicates the input current for a charging source.
POWER_SUPPLY_PROP_CHARGE_TERM_CURRENT - Charge termination current used
to detect the end of charge condition
Signed-off-by: Jenny TC <jenny.tc@intel.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
On the ARM Chromebook tps65090 has two masters: the AP (the main
processor running linux) and the EC (the embedded controller). The AP
is allowed to mess with FETs but the EC is in charge of charge control.
The tps65090 interupt line is routed to both the AP and the EC, which
can cause quite a headache. Having two people adjusting masks and
acking interrupts is a recipe for disaster.
In the shipping kernel we had a hack to have the AP pay attention to
the IRQ but not to ack it. It also wasn't supposed to configure the
IRQ in any way. That hack allowed us to detect when the device was
charging without messing with the EC's state.
The current tps65090 infrastructure makes the above difficult, and it
was a bit of a hack to begin with. Rather than uglify the driver to
support it, just extend the driver's existing notion of "no irq" to
the charger. This makes the charger code poll every 2 seconds for AC
detect, which is sufficient.
For proper functioning, requires (mfd: tps65090: Don't tell child
devices we have an IRQ if we don't). If we don't have that patch
we'll simply fail to probe on devices without an interrupt (just like
we did before this patch).
Signed-off-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
[sre@kernel.org: Use -ENXIO instead of NO_IRQ for missing interrupt,
since NO_IRQ is not available on all architectures.]
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Per license_is_gpl_compatible(), the MODULE_LICENSE() string for GPL v2 is
"GPL v2", not "GPLv2". Use "GPL v2" so this module doesn't taint the
kernel.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
This switches the GPIO poweroff driver to use GPIO descriptors
rather than numeral GPIOs. We get rid of the specific inversion
handling as GPIO descriptors know if they are active low or
high and can assert the line properly, so we do not need to
check the flag OF_GPIO_ACTIVE_LOW returned from the old call
of_get_gpio_flags() anymore.
Also convert to use managed resources and use dev_* message
printing while we're at it.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
One an hdq buss, a missing device reads as 0xff, not -1.
So do a translation to allow detecting of a missing bus.
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
This patch moves data allocated using kzalloc to managed data allocated
using devm_kzalloc and cleans now unnecessary kfrees in probe and remove
functions for both platform and i2c drivers. Also, the unecessary
variable ret and labels batt_failed3, err_free were removed.
The following Coccinele script was used for making the change:
@platform@
identifier p, probefn, removefn;
@@
struct platform_driver p = {
.probe = probefn,
.remove = removefn,
};
@prb@
identifier platform.probefn, pdev;
expression e, e1, e2;
@@
probefn(struct platform_device *pdev, ...) {
<+...
- e = kzalloc(e1, e2)
+ e = devm_kzalloc(&pdev->dev, e1, e2)
...
?-kfree(e);
...+>
}
@rem depends on prb@
identifier platform.removefn;
expression e;
@@
removefn(...) {
<...
- kfree(e);
...>
}
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Pull device mapper fixes from Mike Snitzer:
"Fix the dm-thinp and dm-cache targets to disallow changing the data
device's block size"
* tag 'dm-3.16-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm cache metadata: do not allow the data block size to change
dm thin metadata: do not allow the data block size to change
Pull UBI fixes from Artem Bityutskiy:
"Two UBI fastmap-related fixes for v3.16:
- fix UBI fastmap support which we broke in 3.16-rc1 by reversing the
volumes RB-tree sorting criteria.
- make sure that we scrub all PEBs where we see bit-flips - we were
missing some of them when the fastmap feature was enabled"
* tag 'upstream-3.16-rc6' of git://git.infradead.org/linux-ubifs:
UBI: fastmap: do not miss bit-flips
UBI: fix the volumes tree sorting criteria
Pull Xen fixes from Konrad Rzeszutek Wilk:
"Two fixes found during migration of PV guests. David would be the one
doing this pull but he is on vacation.
Fixes:
- fix console deadlock when resuming PV guests
- fix regression hit when ballooning and resuming PV guests"
* tag 'stable/for-linus-3.16-rc5-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/balloon: set ballooned out pages as invalid in p2m
xen/manage: fix potential deadlock when resuming the console
Pull MTD fixes from Brian Norris:
- Fix ELM suspend/resume
- Reduce warnings if NAND ECC is too weak
- Add CFI support for Sharp LH28F640BF NOR
The last fix is coming in because other commits in the 3.16 cycle
depended on this support.
* tag 'for-linus-20140716' of git://git.infradead.org/linux-mtd:
mtd: cfi_cmdset_0001.c: add support for Sharp LH28F640BF NOR
mtd: nand: reduce the warning noise when the ECC is too weak
mtd: devices: elm: fix elm_context_save() and elm_context_restore() functions
The return value from 'ubi_io_read_ec_hdr()' was stored in 'err', not in 'ret'.
This fix makes sure Fastmap-enabled UBI does not miss bit-flip while reading EC
headers, events and scrubs the affected PEBs.
This issue was reported by Coverity Scan.
Artem: improved the commit message.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Pull GPIO fix from Linus Walleij:
"Fix up some merge confusion from the merge window"
* tag 'gpio-v3.16-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: mcp23s08: Eliminates redundant checking.
The block size for the dm-cache's data device must remained fixed for
the life of the cache. Disallow any attempt to change the cache's data
block size.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Acked-by: Joe Thornber <ejt@redhat.com>
Cc: stable@vger.kernel.org
The block size for the thin-pool's data device must remained fixed for
the life of the thin-pool. Disallow any attempt to change the
thin-pool's data block size.
It should be noted that attempting to change the data block size via
thin-pool table reload will be ignored as a side-effect of the thin-pool
handover that the thin-pool target does during thin-pool table reload.
Here is an example outcome of attempting to load a thin-pool table that
reduced the thin-pool's data block size from 1024K to 512K.
Before:
kernel: device-mapper: thin: 253:4: growing the data device from 204800 to 409600 blocks
After:
kernel: device-mapper: thin metadata: changing the data block size (from 2048 to 1024) is not supported
kernel: device-mapper: table: 253:4: thin-pool: Error creating metadata object
kernel: device-mapper: ioctl: error adding target to table
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Acked-by: Joe Thornber <ejt@redhat.com>
Cc: stable@vger.kernel.org
Pull networking fixes from David Miller:
1) Bluetooth pairing fixes from Johan Hedberg.
2) ieee80211_send_auth() doesn't allocate enough tail room for the SKB,
from Max Stepanov.
3) New iwlwifi chip IDs, from Oren Givon.
4) bnx2x driver reads wrong PCI config space MSI register, from Yijing
Wang.
5) IPV6 MLD Query validation isn't strong enough, from Hangbin Liu.
6) Fix double SKB free in openvswitch, from Andy Zhou.
7) Fix sk_dst_set() being racey with UDP sockets, leading to strange
crashes, from Eric Dumazet.
8) Interpret the NAPI budget correctly in the new systemport driver,
from Florian Fainelli.
9) VLAN code frees percpu stats in the wrong place, leading to crashes
in the get stats handler. From Eric Dumazet.
10) TCP sockets doing a repair can crash with a divide by zero, because
we invoke tcp_push() with an MSS value of zero. Just skip that part
of the sendmsg paths in repair mode. From Christoph Paasch.
11) IRQ affinity bug fixes in mlx4 driver from Amir Vadai.
12) Don't ignore path MTU icmp messages with a zero mtu, machines out
there still spit them out, and all of our per-protocol handlers for
PMTU can cope with it just fine. From Edward Allcutt.
13) Some NETDEV_CHANGE notifier invocations were not passing in the
correct kind of cookie as the argument, from Loic Prylli.
14) Fix crashes in long multicast/broadcast reassembly, from Jon Paul
Maloy.
15) ip_tunnel_lookup() doesn't interpret wildcard keys correctly, fix
from Dmitry Popov.
16) Fix skb->sk assigned without taking a reference to 'sk' in
appletalk, from Andrey Utkin.
17) Fix some info leaks in ULP event signalling to userspace in SCTP,
from Daniel Borkmann.
18) Fix deadlocks in HSO driver, from Olivier Sobrie.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (93 commits)
hso: fix deadlock when receiving bursts of data
hso: remove unused workqueue
net: ppp: don't call sk_chk_filter twice
mlx4: mark napi id for gro_skb
bonding: fix ad_select module param check
net: pppoe: use correct channel MTU when using Multilink PPP
neigh: sysctl - simplify address calculation of gc_* variables
net: sctp: fix information leaks in ulpevent layer
MAINTAINERS: update r8169 maintainer
net: bcmgenet: fix RGMII_MODE_EN bit
tipc: clear 'next'-pointer of message fragments before reassembly
r8152: fix r8152_csum_workaround function
be2net: set EQ DB clear-intr bit in be_open()
GRE: enable offloads for GRE
farsync: fix invalid memory accesses in fst_add_one() and fst_init_card()
igb: do a reset on SR-IOV re-init if device is down
igb: Workaround for i210 Errata 25: Slow System Clock
usbnet: smsc95xx: add reset_resume function with reset operation
dp83640: Always decode received status frames
r8169: disable L23
...
When the module sends bursts of data, sometimes a deadlock happens in
the hso driver when the tty buffer doesn't get the chance to be flushed
quickly enough.
Remove the endless while loop in function put_rxbuf_data() which is
called by the urb completion handler.
If there isn't enough room in the tty buffer, discards all the data
received in the URB.
Cc: David Miller <davem@davemloft.net>
Cc: David Laight <David.Laight@ACULAB.COM>
Cc: One Thousand Gnomes <gnomes@lxorguk.ukuu.org.uk>
Cc: Dan Williams <dcbw@redhat.com>
Cc: Jan Dumon <j.dumon@option.com>
Signed-off-by: Olivier Sobrie <olivier@sobrie.be>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The workqueue "retry_unthrottle_workqueue" is not scheduled anywhere
in the code. So, remove it.
Signed-off-by: Olivier Sobrie <olivier@sobrie.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull firewire fix from Stefan Richter:
"The 1394 drivers cannot and are not supposed to be built on platforms
which don't provide the DMA mapping API (regression since v3.16-rc1
with CONFIG_COMPILE_TEST=y on some architectures)"
* tag 'firewire-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394:
firewire: IEEE 1394 (FireWire) support should depend on HAS_DMA
Commit 568f194e8b ("net: ppp: use
sk_unattached_filter api") causes sk_chk_filter() to be called twice when
setting a PPP pass or active filter. This applies to both the generic PPP
subsystem implemented by drivers/net/ppp/ppp_generic.c and the ISDN PPP
subsystem implemented by drivers/isdn/i4l/isdn_ppp.c. The first call is from
within get_filter(). The second one is through the call chain
ppp_ioctl() or isdn_ppp_ioctl()
--> sk_unattached_filter_create()
--> __sk_prepare_filter()
--> sk_chk_filter()
The first call from within get_filter() should be deleted as get_filter() is
called just before calling sk_unattached_filter_create() later on, which
eventually calls sk_chk_filter() anyway.
For 3.15.x, this proposed change is a bugfix rather than a pure optimization as
in that branch, sk_chk_filter() may replace filter codes by other codes which
are not recognized when executing sk_chk_filter() a second time. So with
3.15.x, if sk_chk_filter() is called twice, the second invocation may yield
EINVAL (this depends on the filter codes found in the filter to be set, but
because the replacement is done for frequently used codes, this is almost
always the case). The net effect is that setting pass and/or active PPP filters
does not work anymore, since sk_unattached_filter_create() always returns
EINVAL due to the second call to sk_chk_filter(), regardless whether the filter
was originally sane or not.
Signed-off-by: Christoph Schulz <develop@kristov.de>
Acked-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Napi id was not marked for gro_skb, this will lead rx busy loop won't
work correctly since they stack never try to call low latency receive
method because of a zero socket napi id. Fix this by marking napi id
for gro_skb.
The transaction rate of 1 byte netperf tcp_rr gets about 50% increased
(from 20531.68 to 30610.88).
Cc: Amir Vadai <amirv@mellanox.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PPP channel MTU is used with Multilink PPP when ppp_mp_explode() (see
ppp_generic module) tries to determine how big a fragment might be. According
to RFC 1661, the MTU excludes the 2-byte PPP protocol field, see the
corresponding comment and code in ppp_mp_explode():
/*
* hdrlen includes the 2-byte PPP protocol field, but the
* MTU counts only the payload excluding the protocol field.
* (RFC1661 Section 2)
*/
mtu = pch->chan->mtu - (hdrlen - 2);
However, the pppoe module *does* include the PPP protocol field in the channel
MTU, which is wrong as it causes the PPP payload to be 1-2 bytes too big under
certain circumstances (one byte if PPP protocol compression is used, two
otherwise), causing the generated Ethernet packets to be dropped. So the pppoe
module has to subtract two bytes from the channel MTU. This error only
manifests itself when using Multilink PPP, as otherwise the channel MTU is not
used anywhere.
In the following, I will describe how to reproduce this bug. We configure two
pppd instances for multilink PPP over two PPPoE links, say eth2 and eth3, with
a MTU of 1492 bytes for each link and a MRRU of 2976 bytes. (This MRRU is
computed by adding the two link MTUs and subtracting the MP header twice, which
is 4 bytes long.) The necessary pppd statements on both sides are "multilink
mtu 1492 mru 1492 mrru 2976". On the client side, we additionally need "plugin
rp-pppoe.so eth2" and "plugin rp-pppoe.so eth3", respectively; on the server
side, we additionally need to start two pppoe-server instances to be able to
establish two PPPoE sessions, one over eth2 and one over eth3. We set the MTU
of the PPP network interface to the MRRU (2976) on both sides of the connection
in order to make use of the higher bandwidth. (If we didn't do that, IP
fragmentation would kick in, which we want to avoid.)
Now we send a ICMPv4 echo request with a payload of 2948 bytes from client to
server over the PPP link. This results in the following network packet:
2948 (echo payload)
+ 8 (ICMPv4 header)
+ 20 (IPv4 header)
---------------------
2976 (PPP payload)
These 2976 bytes do not exceed the MTU of the PPP network interface, so the
IP packet is not fragmented. Now the multilink PPP code in ppp_mp_explode()
prepends one protocol byte (0x21 for IPv4), making the packet one byte bigger
than the negotiated MRRU. So this packet would have to be divided in three
fragments. But this does not happen as each link MTU is assumed to be two bytes
larger. So this packet is diveded into two fragments only, one of size 1489 and
one of size 1488. Now we have for that bigger fragment:
1489 (PPP payload)
+ 4 (MP header)
+ 2 (PPP protocol field for the MP payload (0x3d))
+ 6 (PPPoE header)
--------------------------
1501 (Ethernet payload)
This packet exceeds the link MTU and is discarded.
If one configures the link MTU on the client side to 1501, one can see the
discarded Ethernet frames with tcpdump running on the client. A
ping -s 2948 -c 1 192.168.15.254
leads to the smaller fragment that is correctly received on the server side:
(tcpdump -vvvne -i eth3 pppoes and ppp proto 0x3d)
52:54:00:ad:87:fd > 52:54:00:79:5c:d0, ethertype PPPoE S (0x8864),
length 1514: PPPoE [ses 0x3] MLPPP (0x003d), length 1494: seq 0x000,
Flags [end], length 1492
and to the bigger fragment that is not received on the server side:
(tcpdump -vvvne -i eth2 pppoes and ppp proto 0x3d)
52:54:00:70:9e:89 > 52:54:00:5d:6f:b0, ethertype PPPoE S (0x8864),
length 1515: PPPoE [ses 0x5] MLPPP (0x003d), length 1495: seq 0x000,
Flags [begin], length 1493
With the patch below, we correctly obtain three fragments:
52:54:00:ad:87:fd > 52:54:00:79:5c:d0, ethertype PPPoE S (0x8864),
length 1514: PPPoE [ses 0x1] MLPPP (0x003d), length 1494: seq 0x000,
Flags [begin], length 1492
52:54:00:70:9e:89 > 52:54:00:5d:6f:b0, ethertype PPPoE S (0x8864),
length 1514: PPPoE [ses 0x1] MLPPP (0x003d), length 1494: seq 0x000,
Flags [none], length 1492
52:54:00:ad:87:fd > 52:54:00:79:5c:d0, ethertype PPPoE S (0x8864),
length 27: PPPoE [ses 0x1] MLPPP (0x003d), length 7: seq 0x000,
Flags [end], length 5
And the ICMPv4 echo request is successfully received at the server side:
IP (tos 0x0, ttl 64, id 21925, offset 0, flags [DF], proto ICMP (1),
length 2976)
192.168.222.2 > 192.168.15.254: ICMP echo request, id 30530, seq 0,
length 2956
The bug was introduced in commit c9aa689537
("[PPPOE]: Advertise PPPoE MTU") from the very beginning. This patch applies
to 3.10 upwards but the fix can be applied (with minor modifications) to
kernels as old as 2.6.32.
Signed-off-by: Christoph Schulz <develop@kristov.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
RGMII_MODE_EN bit was defined to 0, while it is actually 6. It was not
much of a problem on older designs where this was a no-op, and the RGMII
data-path would always be enabled, but newer GENET controllers need to
explicitely enable their RGMII data-pad using this bit.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This family of chips was long ago supported by the pre-cfi driver.
CFI code tested on several Zaurus SL-5500 (Collie) 2x16 on 32 bit bus.
Function is_LH28F640BF() mimics is_m29ew() from cmdset_0002.c
Buffer write fixes as seen in 2007 patch c/o
Anti Sullin <anti.sullin <at> artecdesign.ee>
http://comments.gmane.org/gmane.linux.ports.arm.kernel/36733
[Brian: this patch is semi-urgent, because the following patch switches
to using CFI detection for a chip which (until now) is unsupported by
the CFI driver
9218310 ARM: 8084/1: sa1100: collie: revert back to cfi_probe
]
Signed-off-by: Andrea Adami <andrea.adami@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
In commit 67a9ad9b8a ("mtd: nand: Warn the user if the selected ECC
strength is too weak"), a check was added to inform the user when the
ECC used for a NAND device is weaker than the recommended ECC
advertised by the NAND chip. However, the warning uses WARN_ON(),
which has two undesirable side-effects:
- It just prints to the kernel log the fact that there is a warning
in this file, at this line, but it doesn't explain anything about
the warning itself.
- It dumps a stack trace which is very noisy, for something that the
user is most likely not able to fix. If a certain ECC used by the
kernel is weaker than the advertised one, it's most likely to make
sure the kernel uses an ECC that is compatible with the one used by
the bootloader, and changing the bootloader may not necessarily be
easy. Therefore, normal users would not be able to do anything to
fix this very noisy warning, and will have to suffer from it at
every kernel boot. At least every time I see this stack trace in my
kernel boot log, I wonder what new thing is broken, just to realize
that it's once again this NAND ECC warning.
Therefore, this commit turns:
------------[ cut here ]------------
WARNING: CPU: 0 PID: 1 at /home/thomas/projets/linux-2.6/drivers/mtd/nand/nand_base.c:4051 nand_scan_tail+0x538/0x780()
Modules linked in:
CPU: 0 PID: 1 Comm: swapper Not tainted 3.16.0-rc3-dirty #4
[<c000e3dc>] (unwind_backtrace) from [<c000bee4>] (show_stack+0x10/0x14)
[<c000bee4>] (show_stack) from [<c0018180>] (warn_slowpath_common+0x6c/0x8c)
[<c0018180>] (warn_slowpath_common) from [<c001823c>] (warn_slowpath_null+0x1c/0x24)
[<c001823c>] (warn_slowpath_null) from [<c02c50cc>] (nand_scan_tail+0x538/0x780)
[<c02c50cc>] (nand_scan_tail) from [<c0639f78>] (orion_nand_probe+0x224/0x2e4)
[<c0639f78>] (orion_nand_probe) from [<c026da00>] (platform_drv_probe+0x18/0x4c)
[<c026da00>] (platform_drv_probe) from [<c026c1f4>] (really_probe+0x80/0x218)
[<c026c1f4>] (really_probe) from [<c026c47c>] (__driver_attach+0x98/0x9c)
[<c026c47c>] (__driver_attach) from [<c026a8f0>] (bus_for_each_dev+0x64/0x94)
[<c026a8f0>] (bus_for_each_dev) from [<c026bae4>] (bus_add_driver+0x144/0x1ec)
[<c026bae4>] (bus_add_driver) from [<c026cb00>] (driver_register+0x78/0xf8)
[<c026cb00>] (driver_register) from [<c026da5c>] (platform_driver_probe+0x20/0xb8)
[<c026da5c>] (platform_driver_probe) from [<c00088b8>] (do_one_initcall+0x80/0x1d8)
[<c00088b8>] (do_one_initcall) from [<c0620c9c>] (kernel_init_freeable+0xf4/0x1b4)
[<c0620c9c>] (kernel_init_freeable) from [<c049a098>] (kernel_init+0x8/0xec)
[<c049a098>] (kernel_init) from [<c00095f0>] (ret_from_fork+0x14/0x24)
---[ end trace 62f87d875aceccb4 ]---
Into the much shorter, and much more useful:
nand: WARNING: MT29F2G08ABAEAWP: the ECC used on your system is too weak compared to the one required by the NAND chip
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Pull clock driver fixes from Mike Turquette:
"This batch of fixes is for a handful of clock drivers from Allwinner,
Samsung, ST & TI. Most of them are of the "this hardware won't work
without this fix" variety, including patches that fix platforms that
did not boot under certain configurations. Other fixes are the result
of changes to the clock core introduced in 3.15 that had subtle
impacts on the clock drivers.
There are no fixes to the clock framework core in this pull request"
* tag 'clk-fixes-for-linus' of git://git.linaro.org/people/mike.turquette/linux:
clk: spear3xx: Set proper clock parent of uart1/2
clk: spear3xx: Use proper control register offset
clk: qcom: HDMI source sel is 3 not 2
clk: sunxi: fix devm_ioremap_resource error detection code
clk: s2mps11: Fix double free corruption during driver unbind
clk: ti: am43x: Fix boot with CONFIG_SOC_AM33XX disabled
clk: exynos5420: Remove aclk66_peric from the clock tree description
clk/exynos5250: fix bit number for tv sysmmu clock
clk: s3c64xx: Hookup SPI clocks correctly
clk: samsung: exynos4: Remove SRC_MASK_ISP gates
clk: samsung: add more aliases for s3c24xx
clk: samsung: fix several typos to fix boot on s3c2410
clk: ti: set CLK_SET_RATE_NO_REPARENT for ti,mux-clock
clk: ti: am43x: Fix boot with CONFIG_SOC_AM33XX disabled
clk: ti: dra7: return error code in failure case
clk: ti: apll: not allocating enough data
Pull ARM SoC fixes from Olof Johansson:
"This week's arm-soc fixes:
- Another set of OMAP fixes
* Clock fixes
* Restart handling
* PHY regulators
* SATA hwmod data for DRA7
+ Some trivial fixes and removal of a bit of dead code
- Exynos fixes
* A bunch of clock fixes
* Some SMP fixes
* Exynos multi-core timer: register as clocksource and fix ftrace.
+ a few other minor fixes
There's also a couple more patches, and at91 fix for USB caused by
common clock conversion, and more MAINTAINERS entries for shmobile.
We're definitely switching to only regression fixes from here on out,
we've been a little less strict than usual up until now"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (26 commits)
ARM: at91: at91sam9x5: add clocks for usb device
ARM: EXYNOS: Register cpuidle device only on exynos4210 and 5250
ARM: dts: Add clock property for mfc_pd in exynos5420
clk: exynos5420: Add IDs for clocks used in PD mfc
ARM: EXYNOS: Add support for clock handling in power domain
ARM: OMAP2+: Remove non working OMAP HDMI audio initialization
ARM: imx: fix shared gate clock
ARM: dts: Update the parent for Audss clocks in Exynos5420
ARM: EXYNOS: Update secondary boot addr for secure mode
ARM: dts: Fix TI CPSW Phy mode selection on IGEP COM AQUILA.
ARM: dts: am335x-evmsk: Enable the McASP FIFO for audio
ARM: dts: am335x-evm: Enable the McASP FIFO for audio
ARM: OMAP2+: Make GPMC skip disabled devices
ARM: OMAP2+: create dsp device only on OMAP3 SoCs
ARM: dts: dra7-evm: Make VDDA_1V8_PHY supply always on
ARM: DRA7/AM43XX: fix header definition for omap44xx_restart
ARM: OMAP2+: clock/dpll: fix _dpll_test_fint arithmetics overflow
ARM: DRA7: hwmod: Add SYSCONFIG for usb_otg_ss
ARM: DRA7: hwmod: Fixup SATA hwmod
ARM: OMAP3: PRM/CM: Add back macros used by TI DSP/Bridge driver
...
Commit b3d681a4fc ("firewire: Use
COMPILE_TEST for build testing") added COMPILE_TEST as an alternative
dependency for the purpose of build testing the firewire core.
However, this bypasses all other implicit dependencies assumed by PCI,
like HAS_DMA.
If NO_DMA=y:
drivers/built-in.o: In function `fw_iso_buffer_destroy':
(.text+0x36a096): undefined reference to `dma_unmap_page'
drivers/built-in.o: In function `fw_iso_buffer_map_dma':
(.text+0x36a164): undefined reference to `dma_map_page'
drivers/built-in.o: In function `fw_iso_buffer_map_dma':
(.text+0x36a172): undefined reference to `dma_mapping_error'
drivers/built-in.o: In function `sbp2_send_management_orb':
sbp2.c:(.text+0x36c6b4): undefined reference to `dma_map_single'
sbp2.c:(.text+0x36c6c8): undefined reference to `dma_mapping_error'
sbp2.c:(.text+0x36c772): undefined reference to `dma_map_single'
sbp2.c:(.text+0x36c786): undefined reference to `dma_mapping_error'
sbp2.c:(.text+0x36c854): undefined reference to `dma_unmap_single'
sbp2.c:(.text+0x36c872): undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `sbp2_map_scatterlist':
sbp2.c:(.text+0x36ccbc): undefined reference to `scsi_dma_map'
sbp2.c:(.text+0x36cd36): undefined reference to `dma_map_single'
sbp2.c:(.text+0x36cd4e): undefined reference to `dma_mapping_error'
sbp2.c:(.text+0x36cd84): undefined reference to `scsi_dma_unmap'
drivers/built-in.o: In function `sbp2_unmap_scatterlist':
sbp2.c:(.text+0x36cda6): undefined reference to `scsi_dma_unmap'
sbp2.c:(.text+0x36cdc6): undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `complete_command_orb':
sbp2.c:(.text+0x36d6ac): undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `sbp2_scsi_queuecommand':
sbp2.c:(.text+0x36d8e0): undefined reference to `dma_map_single'
sbp2.c:(.text+0x36d8f6): undefined reference to `dma_mapping_error'
Add an explicit dependency on HAS_DMA to fix this.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
The uarts only work when the parent is ras_ahb_clk. The stale 3.5
based ST tree does this in the board file.
Add it to the clk init function. Not pretty, but the mess there is
amazing anyway.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Pull slave-dmaengine fixes from Vinod Koul:
"We have two small fixes. First one from Daniel to handle 0-length
packets for usb cppi dma. Second by Russell for imx-sdam cyclic
residue reporting"
* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
Update imx-sdma cyclic handling to report residue
dma: cppi41: handle 0-length packets
Merge "Samsung fixes-3 for 3.16" from Kukjin Kim:
Samsung fixes-3 for v3.16
- update the parent for Auudss clock because kernel will be hang
during late boot if the parent clock is disabled in bootloader.
- enable clk handing in power domain because while power domain
on/off, its regarding clock source will be reset and it causes
a problem so need to handle it.
- add mux clocks to be used by power domain for exynos5420-mfc
during power domain on/off and property in device tree also.
- register cpuidle only for exynos4210 and exynos5250 because a
system failure will be happened on other exynos SoCs.
* tag 'samsung-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: EXYNOS: Register cpuidle device only on exynos4210 and 5250
ARM: dts: Add clock property for mfc_pd in exynos5420
clk: exynos5420: Add IDs for clocks used in PD mfc
ARM: EXYNOS: Add support for clock handling in power domain
ARM: dts: Update the parent for Audss clocks in Exynos5420
Signed-off-by: Olof Johansson <olof@lixom.net>
Pull USB fixes from Greg KH:
"Here are some small USB fixes, PHY driver fixes (they ended up in this
tree for lack of somewhere else to put them), and some new USB device
ids"
* tag 'usb-3.16-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
phy: omap-usb2: Balance pm_runtime_enable() on probe failure and remove
phy: core: Fix error path in phy_create()
drivers: phy: phy-samsung-usb2.c: Add missing MODULE_DEVICE_TABLE
phy: omap-usb2: fix devm_ioremap_resource error detection code
phy: sun4i: depend on RESET_CONTROLLER
USB: serial: ftdi_sio: Add Infineon Triboard
USB: ftdi_sio: Add extra PID.
usb: option: Add ID for Telewell TW-LTE 4G v2
USB: cp210x: add support for Corsair usb dongle
Pull tty/serial fixes from Greg KH:
"Here are some small serial fixes that resolve some reported problems
that started in 3.15 with some serial drivers.
And there's a new dt binding for a serial driver, which was all that
was needed for the renesas serial driver"
* tag 'tty-3.16-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial: sh-sci: Add device tree support for r8a7{778,740,3a4} and sh73a0
serial: imx: Fix build breakage
serial: arc_uart: Use uart_circ_empty() for open-coded comparison
serial: Test for no tx data on tx restart
Pull char/misc driver fixes from Greg KH:
"Here are two hyperv driver fixes, and one i8k driver fix for 3.16"
* tag 'char-misc-3.16-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
i8k: Fix non-SMP operation
Drivers: hv: util: Fix a bug in the KVP code
Drivers: hv: vmbus: Fix a bug in the channel callback dispatch code
Pull IIO fixes from Greg KH:
"Here are some IIO driver fixes for 3.16-rc5. Nothing major, just
resolves some minor issues that have been reported"
* tag 'staging-3.16-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
iio: ti_am335x_adc: Fix: Use same step id at FIFOs both ends
iio:tcs3472: Check for buffer enabled and locking
iio: hid-sensor-prox: Fix return values
iio: hid-sensor-gyro-3d: Fix return values
iio: hid-sensor-als: Fix return values
iio: hid-sensor-magn-3d: Fix return values
iio: hid-sensor-accel-3d: Fix return values
iio: hid-sensor-press: Fix return values
If probe fails then we need to call pm_runtime_disable() to balance
out the previous pm_runtime_enable() call. Else it will cause
unbalanced pm_runtime_enable() call in the succeding probe call.
This anomaly was observed when the call to devm_phy_create() failed
with -EPROBE_DEFER.
Balance out the pm_runtime_enable() call in .remove() as well.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Prevent resources from being freed twice in case device_add() call
fails within phy_create(). Also use ida_simple_remove() instead of
ida_remove() as we had used ida_simple_get() to allocate the ida.
Cc: 3.13+ <stable@vger.kernel.org> # 3.13+
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Allow phy-exynos-usb2 to be autoloaded based on devicetree information.
Tested on Odroid X2 with its USB subsystem build as modules.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
devm_ioremap_resource returns an ERR_PTR value, not NULL, on failure.
A simplified version of the semantic match that finds this problem is as
follows:
// <smpl>
@@
expression e,e1;
statement S;
@@
*e = devm_ioremap_resource(...);
if (!e1) S
// </smpl>
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver depend on the reset framework in a mandatory way. Make sure
reset_control_get is defined by adding this dependency in Kconfig
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The transport offset of the IPv4 packet should be fixed and wouldn't
be out of the hw limitation, so the r8152_csum_workaround() should
be used for IPv6 packets.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dmitry Artamonow