Pull ARM SoC/OMAP GPMC driver cleanup and move from Arnd Bergmann:
"The GPMC driver has traditionally been considered a part of the OMAP
platform code and tightly interweaved with some of the boards.
With this cleanup, it has finally come to the point where it makes
sense to move it out of arch/arm into drivers/memory, where we already
have other drivers for similar hardware. The cleanups are still
ongoing, with the goal of eventually having a standalone driver that
does not require an interface to architecture code.
This is a separate branch because of dependencies on multiple other
branches, and to keep the drivers changes separate from the normal
cleanups"
* tag 'omap-gpmc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
memory: gpmc: Move omap gpmc code to live under drivers
ARM: OMAP2+: Move GPMC initcall to devices.c
ARM: OMAP2+: Prepare to move GPMC to drivers by platform data header
ARM: OMAP2+: Remove unnecesary include in GPMC driver
ARM: OMAP2+: Drop board file for 3430sdp
ARM: OMAP2+: Drop board file for ti8168evm
ARM: OMAP2+: Drop legacy code for gpmc-smc91x.c
ARM: OMAP2+: Require proper GPMC timings for devices
ARM: OMAP2+: Show bootloader GPMC timings to allow configuring the .dts file
ARM: OMAP2+: Fix support for multiple devices on a GPMC chip select
ARM: OMAP2+: gpmc: Sanity check GPMC fck on probe
ARM: OMAP2+: gpmc: Keep Chip Select disabled while configuring it
ARM: OMAP2+: gpmc: Always enable A26-A11 for non NAND devices
ARM: OMAP2+: gpmc: Error out if timings fail in gpmc_probe_generic_child()
ARM: OMAP2+: gpmc: Print error message in set_gpmc_timing_reg()
Pull ARM SoC driver updates from Arnd Bergmann:
"These are changes for drivers that are intimately tied to some SoC and
for some reason could not get merged through the respective subsystem
maintainer tree.
The largest single change here this time around is the Tegra
iommu/memory controller driver, which gets updated to the new iommu DT
binding. More drivers like this are likely to follow for the
following merge window, but we should be able to do those through the
iommu maintainer.
Other notable changes are:
- reset controller drivers from the reset maintainer (socfpga, sti,
berlin)
- fixes for the keystone navigator driver merged last time
- at91 rtc driver changes related to the at91 cleanups
- ARM perf driver changes from Will Deacon
- updates for the brcmstb_gisb driver"
* tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (53 commits)
clocksource: arch_timer: Allow the device tree to specify uninitialized timer registers
clocksource: arch_timer: Fix code to use physical timers when requested
memory: Add NVIDIA Tegra memory controller support
bus: brcmstb_gisb: Add register offset tables for older chips
bus: brcmstb_gisb: Look up register offsets in a table
bus: brcmstb_gisb: Introduce wrapper functions for MMIO accesses
bus: brcmstb_gisb: Make the driver buildable on MIPS
of: Add NVIDIA Tegra memory controller binding
ARM: tegra: Move AHB Kconfig to drivers/amba
amba: Add Kconfig file
clk: tegra: Implement memory-controller clock
serial: samsung: Fix serial config dependencies for exynos7
bus: brcmstb_gisb: resolve section mismatch
ARM: common: edma: edma_pm_resume may be unused
ARM: common: edma: add suspend resume hook
powerpc/iommu: Rename iommu_[un]map_sg functions
rtc: at91sam9: add DT bindings documentation
rtc: at91sam9: use clk API instead of relying on AT91_SLOW_CLOCK
ARM: at91: add clk_lookup entry for RTT devices
rtc: at91sam9: rework the Kconfig description
...
Pull ARM SoC platform changes from Arnd Bergmann:
"New and updated SoC support, notable changes include:
- bcm:
brcmstb SMP support
initial iproc/cygnus support
- exynos:
Exynos4415 SoC support
PMU and suspend support for Exynos5420
PMU support for Exynos3250
pm related maintenance
- imx:
new LS1021A SoC support
vybrid 610 global timer support
- integrator:
convert to using multiplatform configuration
- mediatek:
earlyprintk support for mt8127/mt8135
- meson:
meson8 soc and l2 cache controller support
- mvebu:
Armada 38x CPU hotplug support
drop support for prerelease Armada 375 Z1 stepping
extended suspend support, now works on Armada 370/XP
- omap:
hwmod related maintenance
prcm cleanup
- pxa:
initial pxa27x DT handling
- rockchip:
SMP support for rk3288
add cpu frequency scaling support
- shmobile:
r8a7740 power domain support
various small restart, timer, pci apmu changes
- sunxi:
Allwinner A80 (sun9i) earlyprintk support
- ux500:
power domain support
Overall, a significant chunk of changes, coming mostly from the usual
suspects: omap, shmobile, samsung and mvebu, all of which already
contain a lot of platform specific code in arch/arm"
* tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (187 commits)
ARM: mvebu: use the cpufreq-dt platform_data for independent clocks
soc: integrator: Add terminating entry for integrator_cm_match
ARM: mvebu: add SDRAM controller description for Armada XP
ARM: mvebu: adjust mbus controller description on Armada 370/XP
ARM: mvebu: add suspend/resume DT information for Armada XP GP
ARM: mvebu: synchronize secondary CPU clocks on resume
ARM: mvebu: make sure MMU is disabled in armada_370_xp_cpu_resume
ARM: mvebu: Armada XP GP specific suspend/resume code
ARM: mvebu: reserve the first 10 KB of each memory bank for suspend/resume
ARM: mvebu: implement suspend/resume support for Armada XP
clk: mvebu: add suspend/resume for gatable clocks
bus: mvebu-mbus: provide a mechanism to save SDRAM window configuration
bus: mvebu-mbus: suspend/resume support
clocksource: time-armada-370-xp: add suspend/resume support
irqchip: armada-370-xp: Add suspend/resume support
ARM: add lolevel debug support for asm9260
ARM: add mach-asm9260
ARM: EXYNOS: use u8 for val[] in struct exynos_pmu_conf
power: reset: imx-snvs-poweroff: add power off driver for i.mx6
ARM: imx: temporarily remove CONFIG_SOC_FSL from LS1021A
...
Pull ARM SoC cleanups from Arnd Bergmann:
"The remaining cleanups for 3.19 are to a large part result of
devicetree conversion nearing completion on two other platforms
besides AT91:
- Like AT91, Renesas shmobile is in the process to migrate to DT and
multiplatform, but using a different approach of doing it one SoC
at a time. For 3.19, the r8a7791 platform and associated "Koelsch"
board are considered complete and we remove the non-DT
non-multiplatform support for this.
- The ARM Versatile Express has supported DT and multiplatform for a
long time, but we have still kept the legacy board files around,
because not all drivers were fully working before. We have finally
taken the last step to remove the board files.
Other changes in this branch are preparation for the later branches or
just unrelated to the more interesting changes:
- The dts files for arm64 get moved into per-vendor directories for a
clearer structure.
- Some dead code removal (zynq, exynos, davinci, imx)
- Using pr_*() macros more consistently instead of printk(KERN_*) in
some platform code"
* tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (71 commits)
ARM: zynq: Remove secondary_startup() declaration from header
ARM: vexpress: Enable regulator framework when MMCI is in use
ARM: vexpress: Remove non-DT code
ARM: imx: Remove unneeded .map_io initialization
ARM: dts: imx6qdl-sabresd: Fix the microphone route
ARM: imx: refactor mxc_iomux_mode()
ARM: imx: simplify clk_pllv3_prepare()
ARM: imx6q: drop unnecessary semicolon
ARM: imx: clean up machine mxc_arch_reset_init_dt reset init
ARM: dts: imx6qdl-rex: Remove unneeded 'fsl,mode' property
ARM: dts: imx6qdl-gw5x: Remove unneeded 'fsl,mode' property
ARM: dts: imx6qdl-sabresd: Use IMX6QDL_CLK_CKO define
ARM: at91: remove useless init_time for DT-only SoCs
ARM: davinci: Remove redundant casts
ARM: davinci: Use standard logging styles
ARM: shmobile: r8a7779: Spelling/grammar s/entity/identity/, s/map/mapping/
ARM: shmobile: sh7372: Spelling/grammar s/entity map/identity mapping/
ARM: shmobile: sh73a0: Spelling/grammar s/entity map/identity mapping/
ARM: EXYNOS: Remove unused static iomapping
ARM: at91: fix build breakage due to legacy board removals
...
Pull ARM SoC non-critical bug fixes from Arnd Bergmann:
"These are bug fixes for harmless problems that were not important
enough to get fixed in 3.19. This contains updates to the MAINTAINERS
file, in particular:
- Ben Dooks stepped down as Samsung co-maintainer (thanks Ben for
long years of maintaining this). Kukjin Kim, who has been doing
the work de-facto by himself recently is now the only maintainer.
- Liviu, Sudeep and Lorenzo from ARM now officially maintain the
Versatile Express platform, which was orphaned (thanks for
- Gregory Fong and Florian Fainelli help out on the Broadcom BCM7XXX
platform
- Ray Jui and Scott Branden are the future maintainers for the newly
merged Broadcom Cygnus platform. Welcome!
In terms of actual fixes, we have the usual set of OMAP bug fixes,
which Tony Lindgren separates out well from the other OMAP changes,
one really ep93xx regression fix against 3.11 that didn't make it for
3.18, a few GIC changes from Marc Zyngier as a preparation for later
rework (the current code is wrong in a harmless way), on Tegra
regression and one samsung spelling fix"
* tag 'fixes-nc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: imx6: fix bogus use of irq_get_irq_data
ARM: imx: irq: fix buggy usage of irq_data irq field
MAINTAINERS: ARM Versatile Express platform, add missing pattern
MAINTAINERS: ARM Versatile Express platform
arm: ep93xx: add dma_masks for the M2P and M2M DMA controllers
MAINTAINERS: Add ahci_st.c to ARCH/STI architecture
MAINTAINERS: add entry for the GISB arbiter driver
MAINTAINERS: update brcmstb entries
MAINTAINERS: update email address and cleanup for exynos entry
ARM: tegra: Re-add removed SoC id macro to tegra_resume()
MAINTAINERS: Entry for Cygnus/iproc arm architecture
ARM: OMAP: serial: remove last vestige of DTR_gpio support.
ARM: OMAP2+: gpmc: Get rid of "ti,elm-id not found" warning
ARM: EXYNOS: fix typo in static struct name "exynos5_list_diable_wfi_wfe"
ARM: OMAP2: Remove unnecessary KERN_* in omap_phy_internal.c
ARM: OMAP4+: Remove unused omap_l3_noc platform init
ARM: dts: Add twl keypad map for omap3 EVM
ARM: dts: Add twl keypad map for LDP
ARM: dts: Fix NAND last partition size on LDP
ARM: OMAP3: Fix errors for omap_l3_smx when booted with device tree
Pull arm64 updates from Will Deacon:
"Here's the usual mixed bag of arm64 updates, also including some
related EFI changes (Acked by Matt) and the MMU gather range cleanup
(Acked by you).
Changes include:
- support for alternative instruction patching from Andre
- seccomp from Akashi
- some AArch32 instruction emulation, required by the Android folks
- optimisations for exception entry/exit code, cmpxchg, pcpu atomics
- mmu_gather range calculations moved into core code
- EFI updates from Ard, including long-awaited SMBIOS support
- /proc/cpuinfo fixes to align with the format used by arch/arm/
- a few non-critical fixes across the architecture"
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (70 commits)
arm64: remove the unnecessary arm64_swiotlb_init()
arm64: add module support for alternatives fixups
arm64: perf: Prevent wraparound during overflow
arm64/include/asm: Fixed a warning about 'struct pt_regs'
arm64: Provide a namespace to NCAPS
arm64: bpf: lift restriction on last instruction
arm64: Implement support for read-mostly sections
arm64: compat: align cacheflush syscall with arch/arm
arm64: add seccomp support
arm64: add SIGSYS siginfo for compat task
arm64: add seccomp syscall for compat task
asm-generic: add generic seccomp.h for secure computing mode 1
arm64: ptrace: allow tracer to skip a system call
arm64: ptrace: add NT_ARM_SYSTEM_CALL regset
arm64: Move some head.text functions to executable section
arm64: jump labels: NOP out NOP -> NOP replacement
arm64: add support to dump the kernel page tables
arm64: Add FIX_HOLE to permanent fixed addresses
arm64: alternatives: fix pr_fmt string for consistency
arm64: vmlinux.lds.S: don't discard .exit.* sections at link-time
...
Pull SCSI updates from James Bottomley:
"This patch is the usual mix of driver updates (srp, ipr, scsi_debug,
NCR5380, fnic, 53c974, ses, wd719x, hpsa, megaraid_sas).
Of those, wd7a9x is new and 53c974 is a rewrite of the old tmscsim
driver and the extensive work by Finn Thain rewrites all the NCR5380
based drivers.
There's also extensive infrastructure updates: a new logging
infrastructure for sense information and a rewrite of the tagged
command queue API and an assortment of minor updates"
* tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (183 commits)
scsi: set fmt to NULL scsi_extd_sense_format() by default
libsas: remove task_collector mode
wd719x: remove dma_cache_sync call
scsi_debug: add Report supported opcodes+tmfs; Compare and write
scsi_debug: change SCSI command parser to table driven
scsi_debug: add Capacity Changed Unit Attention
scsi_debug: append inject error flags onto scsi_cmnd object
scsi_debug: pinpoint invalid field in sense data
wd719x: Add firmware documentation
wd719x: Introduce Western Digital WD7193/7197/7296 PCI SCSI card driver
eeprom-93cx6: Add (read-only) support for 8-bit mode
esas2r: fix an oversight in setting return value
esas2r: fix an error path in esas2r_ioctl_handler
esas2r: fir error handling in do_fm_api
scsi: add SPC-3 command definitions
scsi: rename SERVICE_ACTION_IN to SERVICE_ACTION_IN_16
scsi: remove scsi_driver owner field
scsi: move scsi_dispatch_cmd to scsi_lib.c
scsi: stop passing a gfp_mask argument down the command setup path
scsi: remove scsi_next_command
...
Pull device mapper updates from Mike Snitzer:
- Significant DM thin-provisioning performance improvements to meet
performance requirements that were requested by the Gluster
distributed filesystem.
Specifically, dm-thinp now takes care to aggregate IO that will be
issued to the same thinp block before issuing IO to the underlying
devices. This really helps improve performance on HW RAID6 devices
that have a writeback cache because it avoids RMW in the HW RAID
controller.
- Some stable fixes: fix leak in DM bufio if integrity profiles were
enabled, use memzero_explicit in DM crypt to avoid any potential for
information leak, and a DM cache fix to properly mark a cache block
dirty if it was promoted to the cache via the overwrite optimization.
- A few simple DM persistent data library fixes
- DM cache multiqueue policy block promotion improvements.
- DM cache discard improvements that take advantage of range
(multiblock) discard support in the DM bio-prison. This allows for
much more efficient bulk discard processing (e.g. when mkfs.xfs
discards the entire device).
- Some small optimizations in DM core and RCU deference cleanups
- DM core changes to suspend/resume code to introduce the new internal
suspend/resume interface that the DM thin-pool target now uses to
suspend/resume active thin devices when the thin-pool must
suspend/resume.
This avoids forcing userspace to track all active thin volumes in a
thin-pool when the thin-pool is suspended for the purposes of
metadata or data space resize.
* tag 'dm-3.19-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm: (49 commits)
dm crypt: use memzero_explicit for on-stack buffer
dm space map metadata: fix sm_bootstrap_get_count()
dm space map metadata: fix sm_bootstrap_get_nr_blocks()
dm bufio: fix memleak when using a dm_buffer's inline bio
dm cache: fix spurious cell_defer when dealing with partial block at end of device
dm cache: dirty flag was mistakenly being cleared when promoting via overwrite
dm cache: only use overwrite optimisation for promotion when in writeback mode
dm cache: discard block size must be a multiple of cache block size
dm cache: fix a harmless race when working out if a block is discarded
dm cache: when reloading a discard bitset allow for a different discard block size
dm cache: fix some issues with the new discard range support
dm array: if resizing the array is a noop set the new root to the old one
dm: use rcu_dereference_protected instead of rcu_dereference
dm thin: fix pool_io_hints to avoid looking at max_hw_sectors
dm thin: suspend/resume active thin devices when reloading thin-pool
dm: enhance internal suspend and resume interface
dm thin: do not allow thin device activation while pool is suspended
dm: add presuspend_undo hook to target_type
dm: return earlier from dm_blk_ioctl if target doesn't implement .ioctl
dm thin: remove stale 'trim' message in block comment above pool_message
...
Pull regulator updates from Mark Brown:
"The main thing this time around is support for suspend mode
configuration from DT which will enable some very useful power savings
on systems where we can't rely on the bootloader configuration. We
still don't really support dynamic configuration of this at runtime,
that may come later if there is any demand.
Summary:
- Support for specifying the target regulation mode and voltage
during system suspend via DT, enabling power savings in that mode.
- Reduce the default verbosity of the logging on boot, improving boot
times especially for systems with very large numbers of regulators.
- Lots of cleanups and fixes for Maxim PMIC drivers.
- New driver for Richtek RT5033"
* tag 'regulator-v3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (62 commits)
regulator: core: Fix regualtor_ena_gpio_free not to access pin after freeing
regulator: sky81452: Modify Device Tree structure
regulator: sky81452: Modify Device Tree structure
dt-bindings: Update documentation for "system-power-controller" and fix misspellings
of: Rename "poweroff-source" property to "system-power-controller"
regulator: max77686: Remove support for board files
regulator: max77802: Remove support for board files
regulator: max77802: Fill regulator modes translation callback
regulator: max77802: Document binding for regulator operating modes
regulator: of: Add support for parsing initial and suspend modes
regulator: of: Pass the regulator description in the match table
regulator: of: Add regulator desc param to of_get_regulator_init_data()
regulator: Add mode mapping function to struct regulator_desc
regulator: Document binding for initial and suspend modes
regulator: core: Add PRE_DISABLE notification
regulator: gpio: fix parsing of gpio list
regulator: rpm: add support for RPM-controller SMB208
regulator: da9063: Do not transform local IRQ to virtual
regulator: sky81452: Modify dependent Kconfig symbol
regulator: rt5033: Add RT5033 Regulator device driver
...
Pull regmap updates from Mark Brown:
"A couple of new features this time around, nothing that should have
any impact on most users:
- Cleanups and optimization of the path for reading back the register
defaults from the hardware at startup, reducing boot times for
devices that use this (most don't, either populating on demand or
providing defaults).
- A bus implementation for AC'97 devices"
* tag 'regmap-v3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: ac97: Add generic AC'97 callbacks
regmap: cache: Sort include headers alphabetically
regmap: cache: Fix possible ZERO_SIZE_PTR pointer dereferencing error.
regmap: cache: use kmalloc_array instead of kmalloc
regmap: cache: speed regcache_hw_init() up.
regmap: cache: fix errno in regcache_hw_init()
regmap: cache: cleanup regcache_hw_init()
regmap: cache: fix errno in regcache_hw_init()
Pull hwmon updates from Guenter Roeck:
"Notable changes:
- new driver for NCT7802Y
- support for TMP435, LM95233, LM95235, NCT6792D, and NXP LM75B
- regulator support for PMBus chips, specifically LTX2978
- support for humidity sensors to iio-hwmon bridge driver
* tag 'hwmon-for-linus-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (21 commits)
hwmon: (tmp401) Detect TMP435 on all addresses it supports
hwmon: (lm75) Strengthen detect function
hwmon: (gpio-fan) Add a shutdown handler to poweroff the fans
hwmon: (gpio-fan) Allow usage of gpio operations that may sleep
hwmon: (tmp401) Bail out from tmp401_probe() in case of write errors
hwmon: (tmp401) Add support for TI TMP435
hwmon: (lm95234) Add support for LM95233
hwmon: (lm95245) Add support for LM95235
hwmon: (ina2xx) bail-out from ina2xx_probe() in case of configuration errors
hwmon: (nct6775) Add blank lines after declarations
hwmon: (nct6775) Add support for NCT6792D
hwmon: (nct6775) Documentation updates
hwmon: (lm75) Add support for the NXP LM75B
hwmon: Driver for Nuvoton NCT7802Y
hwmon: (ibmpowernv) Convert to module_platform_driver
hwmon: (ibmpowernv) Use platform 'id_table' to probe the device
hwmon: (iio_hwmon) Add support for humidity sensors
hwmon: (ltc2978) Add regulator support
hwmon: (pmbus) Add regulator support
hwmon: (pmbus) add helpers for byte write and read modify write
...
Pull EDAC updates from Borislav Petkov:
"EDAC updates all over the place:
- Enablement for AMD F15h models 0x60 CPUs. Most notably DDR4 RAM
support. Out of tree stuff is adding the required PCI IDs. From
Aravind Gopalakrishnan.
- Enable amd64_edac for 32-bit due to popular demand. From Tomasz
Pala.
- Convert the AMD MCE injection module to debugfs, where it belongs.
- Misc EDAC cleanups"
* tag 'edac_for_3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp:
EDAC, MCE, AMD: Correct formatting of decoded text
EDAC, mce_amd_inj: Add an injector function
EDAC, mce_amd_inj: Add hw-injection attributes
EDAC, mce_amd_inj: Enable direct writes to MCE MSRs
EDAC, mce_amd_inj: Convert mce_amd_inj module to debugfs
EDAC: Delete unnecessary check before calling pci_dev_put()
EDAC, pci_sysfs: remove unneccessary ifdef around entire file
ghes_edac: Use snprintf() to silence a static checker warning
amd64_edac: Build module on x86-32
EDAC, MCE, AMD: Add decoding table for MC6 xec
amd64_edac: Add F15h M60h support
{mv64x60,ppc4xx}_edac,: Remove deprecated IRQF_DISABLED
EDAC: Sync memory types and names
EDAC: Add DDR3 LRDIMM entries to edac_mem_types
x86, amd_nb: Add device IDs to NB tables for F15h M60h
pci_ids: Add PCI device IDs for F15h M60h
Pull MMC updates from Ulf Hansson:
"MMC core:
- Consolidation and cleanups.
- Some improvements regarding error handling.
- Increase maximum amount of block devices.
- Use correct OCR mask for SDIO when restoring power.
- Fix prepared requests while doing BKOPS.
- Convert to modern PM ops.
- Add mmc_send_tuning() API and convert some hosts to use it.
MMC host:
- toshsd: New Toshiba PCI SD controller driver.
- sdhci: 64-bit ADMA support.
- sdhci: Some regulator fixes.
- sdhci: HS400 support.
- sdhci: Various fixes cleanups.
- atmel-mci: Modernization and cleanups.
- atmel-mci: Runtime PM support.
- omap_hsmmc: Modernization and cleanups.
- omap_hsmmc: Fix UHS card with DDR50 support.
- dw_mmc: Support for ARM64 and Exynos 7 variant.
- dw_mmc: Add support for IMG Pistachio variant.
- dw_mmc: Various fixes and cleanups.
- mvsdio: DMA fixes.
- mxs-mmc: Modernization and cleanups.
- mxcmmc: Various fixes"
* tag 'mmc-v3.19-1' of git://git.linaro.org/people/ulf.hansson/mmc: (126 commits)
mmc: sdhci-msm: Convert to mmc_send_tuning()
mmc: sdhci-esdhc-imx: Convert to mmc_send_tuning()
mmc: core: Let mmc_send_tuning() to take struct mmc_host* as parameter
mmc: queue: Improve error handling during allocation of bounce buffers
mmc: sdhci-acpi: Add two host capabilities for Intel
mmc: sdhci-pci: Add two host capabilities for BYT
mmc: sdhci-acpi: Add SDHCI_QUIRK_NO_ENDATTR_IN_NOPDESC
mmc: sdhci-pci: Add SDHCI_QUIRK_NO_ENDATTR_IN_NOPDESC to BYT
mmc: atmel-mci: use probe deferring if dma controller is not ready yet
mmc: atmel-mci: stop using specific initcall
mmc: atmel-mci: remove __init/__exit attributes
mmc: atmel-mci: remove useless DMA stuff for non-dt devices
mmc: omap_hsmmc: Fix UHS card with DDR50 support
mmc: core: add core-level function for sending tuning commands
mmc: core: hold SD Clock before CMD11 during Signal
mmc: mxs-mmc: Check for clk_prepare_enable() error
mmc: mxs-mmc: Propagate the real error
mmc: mxs-mmc: No need to do NULL check on 'iores'
mmc: dw_mmc: Add support for IMG Pistachio
mmc: mxs-mmc: Simplify PM hooks
...
Conflicts:
drivers/scsi/scsi_debug.c
Agreed and tested resolution to a merge problem between a fix in scsi_debug
and a driver update
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Add helper function to write u32 to registers, if we want to put u32
value to 4 continuous register, this can help us reduce tedious work.
Signed-off-by: Micky Ching <micky_ching@realsil.com.cn>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
To be able to use mmc_send_tuning() prior the struct mmc_card has been
allocated, let's convert it to take the struct mmc_host* as parameter
instead.
Suggested-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Dong Aisheng <b29396@freescale.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Pull "ARM: tegra: IOMMU support for v3.19" from Thierry Reding:
This adds the driver pieces required for IOMMU support on Tegra30,
Tegra114 and Tegra124.
* tag 'tegra-for-3.19-iommu' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
memory: Add NVIDIA Tegra memory controller support
of: Add NVIDIA Tegra memory controller binding
ARM: tegra: Move AHB Kconfig to drivers/amba
amba: Add Kconfig file
clk: tegra: Implement memory-controller clock
powerpc/iommu: Rename iommu_[un]map_sg functions
iommu: Improve error handling when setting bus iommu
iommu: Do more input validation in iommu_map_sg()
iommu: Add iommu_map_sg() function
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Pull "Reset controller changes for v3.19" from Philipp Zabel:
This adds a new driver for the sti soc family, and creates
a reset_control_status interface, which is added to the existing
drivers.
* tag 'reset-for-3.19-2' of git://git.pengutronix.de/git/pza/linux:
reset: add socfpga_reset_status
reset: sti: Document sti-picophyreset controllers bindings.
reset: stih407: Add softreset, powerdown and picophy controllers
reset: stih407: Add reset controllers DT bindings
reset: add reset_control_status helper function
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Pull "mvebu SoC suspend changes for v3.19" from Jason Cooper:
- Armada 370/XP suspend/resume support
- mvebu SoC driver suspend/resume support
- irqchip
- clocksource
- mbus
- clk
* tag 'mvebu-soc-suspend-3.19' of git://git.infradead.org/linux-mvebu:
ARM: mvebu: add SDRAM controller description for Armada XP
ARM: mvebu: adjust mbus controller description on Armada 370/XP
ARM: mvebu: add suspend/resume DT information for Armada XP GP
ARM: mvebu: synchronize secondary CPU clocks on resume
ARM: mvebu: make sure MMU is disabled in armada_370_xp_cpu_resume
ARM: mvebu: Armada XP GP specific suspend/resume code
ARM: mvebu: reserve the first 10 KB of each memory bank for suspend/resume
ARM: mvebu: implement suspend/resume support for Armada XP
clk: mvebu: add suspend/resume for gatable clocks
bus: mvebu-mbus: provide a mechanism to save SDRAM window configuration
bus: mvebu-mbus: suspend/resume support
clocksource: time-armada-370-xp: add suspend/resume support
irqchip: armada-370-xp: Add suspend/resume support
Documentation: dt-bindings: minimal documentation for MVEBU SDRAM controller
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
It reverts commit a4b4e0461e ("of: Add standard property for poweroff capability").
As discussed on the mailing list, it makes more sense to rename back to the
old established property name, without the vendor prefix. Problem being that
the word "source" usually tends to be used for inputs and that is out of control
of the OS. The poweroff capability is an output which simply turns the
system-power off. Also, this property might be used by drivers which power-off
the system and power back on subsequent RTC alarms. This seems to suggest to
remove "poweroff" from the property name and to choose "system-power-controller"
as the more generic name. This patchs adds the required renaming changes and
defines an helper function which checks if this property is set.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Acked-by: Grant Likely <grant.likely@linaro.org>
Acked-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for simple on/off control of each channel.
To add regulator support, the pmbus part driver needs to add
regulator_desc information and number of regulators to its
pmbus_driver_info struct.
regulator_desc can be declared using default macro for a
regulator (PMBUS_REGULATOR) that is in pmbus.h
The regulator_init_data can be initialized from either
platform data or the device tree.
Signed-off-by: Alan Tull <atull@opensource.altera.com>
Reviewed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
On Marvell EBU platforms, when doing suspend/resume, the SDRAM window
configuration must be saved on suspend, and restored on
resume. However, it needs to be restored on resume *before*
re-entering the kernel, because the SDRAM window configuration defines
the layout of the memory. For this reason, it cannot simply be done in
the ->suspend() and ->resume() hooks of the mvebu-mbus driver.
Instead, it needs to be restored by the bootloader "boot info"
mechanism used when resuming. This mechanism allows the kernel to
define a list of (address, value) pairs when suspending, that the
bootloader will restore on resume before jumping back into the kernel.
This commit therefore adds a new function to the mvebu-mbus driver,
called mvebu_mbus_save_cpu_target(), which will be called by the
platform code to make the mvebu-mbus driver save the SDRAM window
configuration in a way that can be understood by the bootloader "boot
info" mechanism.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Link: https://lkml.kernel.org/r/1416585613-2113-8-git-send-email-thomas.petazzoni@free-electrons.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Pull staging/IIO driver fixes from Greg KH:
"Here are some staging and IIO driver fixes for 3.18-rc7 that resolve a
number of reported issues, and a new device id for a staging wireless
driver.
All of these have been in linux-next"
* tag 'staging-3.18-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: r8188eu: Add new device ID for DLink GO-USB-N150
staging: r8188eu: Fix scheduling while atomic error introduced in commit fadbe0cd
iio: accel: bmc150: set low default thresholds
iio: accel: bmc150: Fix iio_event_spec direction
iio: accel: bmc150: Send x, y and z motion separately
iio: accel: bmc150: Error handling when mode set fails
iio: gyro: bmg160: Fix iio_event_spec direction
iio: gyro: bmg160: Send x, y and z motion separately
iio: gyro: bmg160: Don't let interrupt mode to be open drain
iio: gyro: bmg160: Error handling when mode set fails
iio: adc: men_z188_adc: Add terminating entry for men_z188_ids
iio: accel: kxcjk-1013: Fix kxcjk10013_set_range
iio: Fix IIO_EVENT_CODE_EXTRACT_DIR bit mask
Pull "move omap gpmc to drivers finally" from Tony Lindgren:
We can finally move the GPMC code to live in drivers/memory for
further clean up work.
Note that we still have dependencies to the legacy booting for
omap3 board-*.c files for setting up the board specific memory
timings. For that we need the timing related things still exposed
in include/linux/omap-gpmc.h. This will all become private data
to the GPMC driver once the legacy booting support can be dropped.
* tag 'omap-for-v3.19/gpmc-move-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
memory: gpmc: Move omap gpmc code to live under drivers
ARM: OMAP2+: Move GPMC initcall to devices.c
ARM: OMAP2+: Prepare to move GPMC to drivers by platform data header
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Now, with the CLCD DT support available, there is no
more reason to keep the non-DT support for V2P-CA9.
Removed, together with "some" supporting code. It was
necessary to make PLAT_VERSATILE_SCHED_CLOCK optional
and selected by the machines still interested in it.
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Pull "The i.MX SoC update for 3.19" from Shawn Guo
- Update i.MX6 suspend code to check DDR instead of CPU type, as the
difference we need to handle is between LPDDR2 and DDR3, not SoCs.
- Set anatop properly for LPDDR2 in DSM mode
- Add support for new SoC LS1021A which integrates dual Cortex-A7
- Add ENET initialization for i.MX6SX platform
- Add cpufreq support for i.MX53 platform
- Add a SNVS based poweroff driver for i.MX6 platforms
- Use ARM Global Timer as clocksource on VF610
Note: the change set is built on top of tag imx-fixes-3.18-2 to resolve
a conflict on file arch/arm/mach-imx/clk-vf610.c.
* tag 'imx-soc-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
power: reset: imx-snvs-poweroff: add power off driver for i.mx6
ARM: imx: temporarily remove CONFIG_SOC_FSL from LS1021A
ARM: imx: clk-vf610: get input clocks from assigned clocks
ARM: imx: Add Freescale LS1021A SMP support
ARM: imx: Add initial support for Freescale LS1021A
ARM: imx53: add cpufreq support
ARM: imx53: clk: add ARM clock
ARM: imx: add CPU clock type
ARM: imx5: add step clock, used when reprogramming PLL1
ARM: imx: add enet init for i.mx6sx
ARM: imx6sx: add imx6sx iomux-gpr field define
ARM: vf610: Add ARM Global Timer clocksource option
ARM: imx: add anatop settings for LPDDR2 when enter DSM mode
ARM: imx: replace cpu type check with ddr type check
ARM: imx: Fix the removal of CONFIG_SPI option
ARM: imx: clk-vf610: define PLL's clock tree
Signed-off-by; Arnd Bergmann <arnd@arndb.de>
Jonathan writes:
Third set of IIO fixes for the 3.18 cycle.
Most of these are fairly standard little fixes, a bmc150 and bmg160 patch
is to make an ABI change to indicated a specific axis in an event rather
than the generic option in the original drivers. As both of these drivers
are new in this cycle it would be ideal to push this minor change through
even though it isn't strictly a fix. A couple of other 'fixes' change
defaults for some settings on these new drivers to more intuitive calues.
Looks like some useful feedback has been coming in for this driver
since it was applied.
* IIO_EVENT_CODE_EXTRACT_DIR bit mask was wrong and has been for a while
0xCF clearly doesn't give a contiguous bitmask.
* kxcjk-1013 range setting was failing to mask out the previous value
in the register and hence was 'enable only'.
* men_z188 device id table wasn't null terminated.
* bmg160 and bmc150 both failed to correctly handling an error in mode
setting.
* bmg160 and bmc150 both had a bug in setting the event direction in the
event spec (leads to an attribute name being incorrect)
* bmg160 defaulted to an open drain output for the interrupt - as a default
this obviously only works with some interrupt chips - hence change the
default to push-pull (note this is a new driver so we aren't going to
cause any regressions with this change).
* bmc150 had an unintuitive default for the rate of change (motion detector)
so change it to 0 (new driver so change of default won't cause any
regressions).
Drivers can use the of_regulator_match() function to parse the regulator
init_data from DT. A match table is used to specify the name of the node
containing the regulators, the device node and to return the init_data
to the caller.
But also the static regulator descriptor is needed to correctly extract
some DT properties like the regulator initial and suspend modes. Use the
match table to pass that information.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
The of_get_regulator_init_data() function is used to extract the regulator
init_data but information on how to extract certain data is defined in the
static regulator descriptor (e.g: how to map the hardware operating modes).
Add a const struct regulator_desc * parameter to the function signature so
the parsing logic could use the information in the struct regulator_desc.
of_get_regulator_init_data() relies on of_get_regulation_constraints() to
actually extract the init_data so it has to pass the struct regulator_desc
but that is modified on a later patch.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
The "regulator-initial-mode" and "regulator-mode" DT properties allows
to configure the regulator operating modes at startup or when a system
enters into a susend state.
But these properties use as valid values the operating modes supported
by each device while the core deals with the standard operating modes.
So a mapping function is needed to translate from the hardware specific
modes to the standard ones.
This mapping is a non-varying configuration for each regulator, so add
a function pointer to struct regulator_desc that will allow drivers to
define their callback to do the modes translation.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
This reverts commit 85c8555ff0 ("KVM: check for !is_zero_pfn() in
kvm_is_mmio_pfn()") and renames the function to kvm_is_reserved_pfn.
The problem being addressed by the patch above was that some ARM code
based the memory mapping attributes of a pfn on the return value of
kvm_is_mmio_pfn(), whose name indeed suggests that such pfns should
be mapped as device memory.
However, kvm_is_mmio_pfn() doesn't do quite what it says on the tin,
and the existing non-ARM users were already using it in a way which
suggests that its name should probably have been 'kvm_is_reserved_pfn'
from the beginning, e.g., whether or not to call get_page/put_page on
it etc. This means that returning false for the zero page is a mistake
and the patch above should be reverted.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
According to the SD card spec, Add a manual tuning command function
for SDR104/HS200.
Sending command 19 or command 21 to read data and compare with the
tunning block pattern.
This patch will help to decrease some platform private codes in SDHCI
platform_execute_tuning() callbacks.
Signed-off-by: Minda Chen <Minda.Chen@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The bit of sdio interrupt is 16 in designware implementation,
but it is 24 on Rockchip SoCs.This patch add sdio_id0 for the
number of slot0 in the SDIO interrupt registers.
Signed-off-by: Addy Ke <addy.ke@rock-chips.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
omap_hsmmc only supports one slot. So slot id is always zero, and
slot id was never used in the callbacks anyway
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
These callbacks are set during driver probe and not from the platform
init, -- evtl. they had been for oamp 1/2 -- for omap3 they are local
functions of the driver. These indirection could be dropped
altogether in favor of regular function calls TODO
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
omap_hsmmc supports only one slot per controller, see OMAP_MMC_MAX_SLOTS.
This unnecessary indirection leads to confusion in the omap_hsmmc driver.
For example the card_detect callback is not installed by platform code
but from the driver probe function. So it should be a field of
omap_hsmmc_host. But since it is declared under the platform slot while
the drivers struct omap_hsmmc_host has no slot abstraction, this looks
like a bug, especially when not familiar that this driver only supports
1 slot anyway.
Either we should add a slot abstraction to omap_hsmmc_host or remove
it from the platform data struct. Removed since slot multiplexing is
an un-implemented feature
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
platform data is built from omap2_hsmmc_info, remove all fields that
are never set in omap_hsmmc_info, hence never copied to platform data.
Note that the omap_hsmmc driver is not affected by this patch those
fields were completely unused.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
- omap mmc driver supports multiplexing, omap_mmc_hs doesn't
this leads to one of the major confusions in the omap_hsmmc driver
- platform data should be read-only for the driver
most callbacks are not set by the omap3 platform init code while still
required. So they are set from the driver probe function, which is against
the paradigm that platform-data should not be modified by the driver
typical examples are card_detect, read_only callbacks
un-bundling by searching for driver name \"omap_hsmmc in the
arch/arm folder. omap_hsmmc_platform_data is not initialized directly,
but from omap2_hsmmc_info, which is defined in a separate header file
not touched by this patch
hwmod includes platform headers to declare features of the platform. All
the declared features are prefixed OMAP_HSMMC. There is no need to
include platform header from hwmod other except for feature defines
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
MMC core already has support for HS400. Add HS400
support to SDHCI driver. The SDHC Standard specification
does not define HS400 so consequently HS400 support is
non-standard. However HS400 is not selected without
the host controller setting the corresponding capability
flags so host controllers not yet supporting HS400
will not be affected. To support that, a quirk
SDHCI_QUIRK2_CAPS_BIT63_FOR_HS400 is introduced to
enable the use of capabilities register reserved bit-63
to indicate HS400 support.
Because HS400 is non-standard for SDHCI, it is possible
that different vendors will do things in different ways.
However HS200 support faced the same issue but currently
there is only one solution. As such, no attempt has
been made to provide for alternate HS400 solutions except
for SDHCI_QUIRK2_CAPS_BIT63_FOR_HS400.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
1.2V HS200 mode capability is cleared if there is not a voltage
regulator that supports 1.2V. Do the same for 1.2V HS400 mode.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Synopsys DW_MMC IP core supports Internal DMA Controller with 64-bit address mode from IP version 2.70a onwards.
Updated the driver to support IDMAC 64-bit addressing mode.
Signed-off-by: Prabu Thangamuthu <prabu.t@synopsys.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Linus Torvalds