mirror of
https://github.com/hardkernel/linux.git
synced 2026-06-07 11:26:02 +09:00
ARM: dts: rockchip: add rk3506g-demo-display-control.dts
Change-Id: I2b0b5d31694168c37ba122a49ded99da64dbe3dc Signed-off-by: Zain Wang <wzz@rock-chips.com>
This commit is contained in:
Zain Wang
@@ -1223,6 +1223,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += \
|
||||
rk3308hs-voice-module-board-v10-aarch32.dtb \
|
||||
rk3503g-evb1-v10.dtb \
|
||||
rk3506b-evb1-v10.dtb \
|
||||
rk3506g-demo-display-control.dtb \
|
||||
rk3506g-evb1-v10.dtb \
|
||||
rk3506g-evb1-v10-amp.dtb \
|
||||
rk3506g-evb1-v10-flexbus-adc-dac.dtb \
|
||||
|
||||
117
arch/arm/boot/dts/rk3506-rk801.dtsi
Normal file
117
arch/arm/boot/dts/rk3506-rk801.dtsi
Normal file
@@ -0,0 +1,117 @@
|
||||
// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
|
||||
/*
|
||||
* Copyright (c) 2024 Rockchip Electronics Co., Ltd.
|
||||
*
|
||||
*/
|
||||
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/pinctrl/rockchip.h>
|
||||
|
||||
&i2c0 {
|
||||
status = "okay";
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&rm_io0_i2c0_scl &rm_io2_i2c0_sda>;
|
||||
|
||||
rk801: rk801@27 {
|
||||
compatible = "rockchip,rk801";
|
||||
status = "okay";
|
||||
reg = <0x27>;
|
||||
interrupt-parent = <&gpio0>;
|
||||
interrupts = <RK_PC2 IRQ_TYPE_LEVEL_LOW>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pmic_int>;
|
||||
rockchip,system-power-controller;
|
||||
wakeup-source;
|
||||
|
||||
vcc1-supply = <&vcc12v_dc>;
|
||||
vcc2-supply = <&vcc12v_dc>;
|
||||
vcc3-supply = <&vcc5v0_sys>;
|
||||
vcc4-supply = <&vcc5v0_sys>;
|
||||
vcc5-supply = <&vcc3v3_sys>;
|
||||
vcc6-supply = <&vcc3v3_sys>;
|
||||
vcc7-supply = <&vcc3v3_sys>;
|
||||
|
||||
regulators {
|
||||
vcc3v3_sys: DCDC_REG1 {
|
||||
regulator-name = "vcc3v3_sys";
|
||||
regulator-min-microvolt = <3300000>;
|
||||
regulator-max-microvolt = <3300000>;
|
||||
regulator-initial-mode = <0x1>;
|
||||
regulator-boot-on;
|
||||
regulator-always-on;
|
||||
regulator-state-mem {
|
||||
regulator-mode = <0x2>;
|
||||
regulator-on-in-suspend;
|
||||
regulator-suspend-microvolt = <3300000>;
|
||||
};
|
||||
};
|
||||
|
||||
vcc5v0_sys: DCDC_REG2 {
|
||||
regulator-name = "vcc5v0_sys";
|
||||
regulator-min-microvolt = <5000000>;
|
||||
regulator-max-microvolt = <5000000>;
|
||||
regulator-initial-mode = <0x1>;
|
||||
regulator-boot-on;
|
||||
regulator-always-on;
|
||||
regulator-state-mem {
|
||||
regulator-mode = <0x2>;
|
||||
regulator-on-in-suspend;
|
||||
regulator-suspend-microvolt = <5000000>;
|
||||
};
|
||||
};
|
||||
|
||||
vcc_ddr: DCDC_REG3 {
|
||||
regulator-name = "vcc_ddr";
|
||||
regulator-boot-on;
|
||||
regulator-always-on;
|
||||
regulator-state-mem {
|
||||
regulator-mode = <0x2>;
|
||||
regulator-on-in-suspend;
|
||||
};
|
||||
};
|
||||
|
||||
vdd_cpu: DCDC_REG4 {
|
||||
regulator-name = "vdd_cpu";
|
||||
regulator-min-microvolt = <500000>;
|
||||
regulator-max-microvolt = <1500000>;
|
||||
regulator-initial-mode = <0x1>;
|
||||
regulator-boot-on;
|
||||
regulator-always-on;
|
||||
regulator-state-mem {
|
||||
regulator-mode = <0x2>;
|
||||
regulator-off-in-suspend;
|
||||
};
|
||||
};
|
||||
|
||||
vdd0v9_sys: LDO_REG1 {
|
||||
regulator-name = "vdd0v9_sys";
|
||||
regulator-min-microvolt = <900000>;
|
||||
regulator-max-microvolt = <900000>;
|
||||
regulator-boot-on;
|
||||
regulator-always-on;
|
||||
regulator-state-mem {
|
||||
regulator-on-in-suspend;
|
||||
regulator-suspend-microvolt = <900000>;
|
||||
};
|
||||
};
|
||||
|
||||
vcc_1v8: LDO_REG2 {
|
||||
regulator-name = "vcc_1v8";
|
||||
regulator-min-microvolt = <1800000>;
|
||||
regulator-max-microvolt = <1800000>;
|
||||
regulator-boot-on;
|
||||
regulator-always-on;
|
||||
regulator-state-mem {
|
||||
regulator-on-in-suspend;
|
||||
regulator-suspend-microvolt = <1800000>;
|
||||
};
|
||||
};
|
||||
|
||||
vcc_3v3: SWITCH_REG {
|
||||
regulator-name = "vcc_3v3";
|
||||
regulator-boot-on;
|
||||
regulator-always-on;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
509
arch/arm/boot/dts/rk3506g-demo-display-control.dts
Normal file
509
arch/arm/boot/dts/rk3506g-demo-display-control.dts
Normal file
@@ -0,0 +1,509 @@
|
||||
// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
|
||||
/*
|
||||
* Copyright (c) 2024 Rockchip Electronics Co., Ltd.
|
||||
*/
|
||||
|
||||
/dts-v1/;
|
||||
|
||||
#include <dt-bindings/display/drm_mipi_dsi.h>
|
||||
#include <dt-bindings/input/rk-input.h>
|
||||
#include <dt-bindings/sensor-dev.h>
|
||||
#include "rk3506.dtsi"
|
||||
#include "rk3506-rk801.dtsi"
|
||||
|
||||
/* TODO:
|
||||
1. RK801
|
||||
2. DISPLAY
|
||||
3. AUDIO
|
||||
4. ZIGBEE
|
||||
5. Light/Proximity Sensor
|
||||
6. GMAC (bottom board)
|
||||
---------------
|
||||
usb ? otg vbus
|
||||
rtc ? clk out
|
||||
--------------
|
||||
led require config: CONFIG_LEDS_TRIGGER_HEARTBEAT / CONFIG_LEDS_GPIO
|
||||
rtc require config: CONFIG_RTC_DRV_HYM8563
|
||||
*/
|
||||
|
||||
/ {
|
||||
model = "Rockchip RK3506G(QFN128) DEMO1 V10 Board";
|
||||
compatible = "rockchip,rk3506g-demo-display-control", "rockchip,rk3506";
|
||||
|
||||
chosen {
|
||||
bootargs = "earlycon=uart8250,mmio32,0xff0a0000 console=ttyFIQ0 ubi.mtd=4 ubi.block=0,rootfs root=/dev/ubiblock0_0 rootfstype=squashfs rootwait snd_aloop.index=7 snd_aloop.use_raw_jiffies=1";
|
||||
};
|
||||
|
||||
adc_keys: adc-keys {
|
||||
compatible = "adc-keys";
|
||||
io-channels = <&saradc 1>;
|
||||
io-channel-names = "buttons";
|
||||
keyup-threshold-microvolt = <1800000>;
|
||||
poll-interval = <100>;
|
||||
|
||||
vol-up-key {
|
||||
label = "volume up";
|
||||
linux,code = <KEY_VOLUMEUP>;
|
||||
press-threshold-microvolt = <20000>;
|
||||
};
|
||||
};
|
||||
|
||||
backlight: backlight {
|
||||
compatible = "pwm-backlight";
|
||||
pwms = <&pwm0_4ch_2 0 25000 0>;
|
||||
brightness-levels = <
|
||||
0 20 20 21 21 22 22 23
|
||||
23 24 24 25 25 26 26 27
|
||||
27 28 28 29 29 30 30 31
|
||||
31 32 32 33 33 34 34 35
|
||||
35 36 36 37 37 38 38 39
|
||||
40 41 42 43 44 45 46 47
|
||||
48 49 50 51 52 53 54 55
|
||||
56 57 58 59 60 61 62 63
|
||||
64 65 66 67 68 69 70 71
|
||||
72 73 74 75 76 77 78 79
|
||||
80 81 82 83 84 85 86 87
|
||||
88 89 90 91 92 93 94 95
|
||||
96 97 98 99 100 101 102 103
|
||||
104 105 106 107 108 109 110 111
|
||||
112 113 114 115 116 117 118 119
|
||||
120 121 122 123 124 125 126 127
|
||||
128 129 130 131 132 133 134 135
|
||||
136 137 138 139 140 141 142 143
|
||||
144 145 146 147 148 149 150 151
|
||||
152 153 154 155 156 157 158 159
|
||||
160 161 162 163 164 165 166 167
|
||||
168 169 170 171 172 173 174 175
|
||||
176 177 178 179 180 181 182 183
|
||||
184 185 186 187 188 189 190 191
|
||||
192 193 194 195 196 197 198 199
|
||||
200 201 202 203 204 205 206 207
|
||||
208 209 210 211 212 213 214 215
|
||||
216 217 218 219 220 221 222 223
|
||||
224 225 226 227 228 229 230 231
|
||||
232 233 234 235 236 237 238 239
|
||||
240 241 242 243 244 245 246 247
|
||||
248 249 250 251 252 253 254 255
|
||||
>;
|
||||
default-brightness-level = <200>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
/* extcon_usb: extcon-usb {
|
||||
compatible = "linux,extcon-usb-gpio";
|
||||
vbus-gpio = <&gpio1 RK_PC5 GPIO_ACTIVE_LOW>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&usb_extcon_vbus>;
|
||||
status = "okay";
|
||||
};*/
|
||||
|
||||
fiq_debugger: fiq-debugger {
|
||||
compatible = "rockchip,fiq-debugger";
|
||||
rockchip,serial-id = <0>;
|
||||
rockchip,wake-irq = <0>;
|
||||
rockchip,irq-mode-enable = <1>;
|
||||
rockchip,baudrate = <1500000>; /* Only 115200 and 1500000 */
|
||||
interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>;
|
||||
};
|
||||
|
||||
leds: leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
work_led: work-led {
|
||||
gpios = <&gpio0 RK_PD0 GPIO_ACTIVE_HIGH>;
|
||||
linux,default-trigger = "heartbeat";
|
||||
};
|
||||
};
|
||||
|
||||
reserved-memory {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
ranges;
|
||||
|
||||
cma: linux,cma {
|
||||
compatible = "shared-dma-pool";
|
||||
reusable;
|
||||
size = <0x2000000>;
|
||||
linux,cma-default;
|
||||
};
|
||||
|
||||
drm_logo: drm-logo@0 {
|
||||
compatible = "rockchip,drm-logo";
|
||||
reg = <0x0 0x0>;
|
||||
};
|
||||
};
|
||||
|
||||
vcc3v3_lcd_n: vcc3v3-lcd0-n {
|
||||
compatible = "regulator-fixed";
|
||||
enable-active-high;
|
||||
gpio = <&gpio0 RK_PA1 GPIO_ACTIVE_HIGH>;
|
||||
regulator-name = "vcc3v3_lcd_n";
|
||||
regulator-boot-on;
|
||||
regulator-state-mem {
|
||||
regulator-off-in-suspend;
|
||||
};
|
||||
};
|
||||
|
||||
vcc12v_dc: vcc12v-dc {
|
||||
compatible = "regulator-fixed";
|
||||
regulator-name = "vcc12v_dc";
|
||||
regulator-always-on;
|
||||
regulator-boot-on;
|
||||
regulator-min-microvolt = <12000000>;
|
||||
regulator-max-microvolt = <12000000>;
|
||||
};
|
||||
|
||||
vdd_0v9: vdd-0v9 {
|
||||
compatible = "regulator-fixed";
|
||||
regulator-name = "vdd_0v9";
|
||||
regulator-always-on;
|
||||
regulator-boot-on;
|
||||
regulator-min-microvolt = <900000>;
|
||||
regulator-max-microvolt = <900000>;
|
||||
vin-supply = <&vcc3v3_sys>;
|
||||
};
|
||||
};
|
||||
|
||||
&can0 {
|
||||
assigned-clocks = <&cru CLK_CAN0>;
|
||||
assigned-clock-rates = <200000000>;
|
||||
pinctrl-0 = <&rm_io27_can0_tx &rm_io28_can0_rx>;
|
||||
pinctrl-names = "default";
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&cpu0 {
|
||||
cpu-supply = <&vdd_cpu>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&display_subsystem {
|
||||
logo-memory-region = <&drm_logo>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&dsi {
|
||||
status = "okay";
|
||||
rockchip,lane-rate = <450>;
|
||||
dsi_panel: panel@0 {
|
||||
status = "okay";
|
||||
compatible = "simple-panel-dsi";
|
||||
reg = <0>;
|
||||
backlight = <&backlight>;
|
||||
prepare-delay-ms = <5>;
|
||||
reset-delay-ms = <1>;
|
||||
init-delay-ms = <80>;
|
||||
disable-delay-ms = <10>;
|
||||
unprepare-delay-ms = <5>;
|
||||
|
||||
width-mm = <83>;
|
||||
height-mm = <83>;
|
||||
|
||||
dsi,flags = <(MIPI_DSI_MODE_VIDEO | MIPI_DSI_MODE_VIDEO_BURST |
|
||||
MIPI_DSI_MODE_LPM | MIPI_DSI_MODE_NO_EOT_PACKET)>;
|
||||
dsi,format = <MIPI_DSI_FMT_RGB888>;
|
||||
dsi,lanes = <2>;
|
||||
panel-init-sequence = [
|
||||
39 00 06 ff 77 01 00 00 10
|
||||
39 00 03 c0 3b 00
|
||||
39 00 03 c1 0d 02
|
||||
39 00 03 c2 21 08
|
||||
39 00 11 b0 00 11 18 0e 11 06 07 08 07 22 04 12 0f aa 31 18
|
||||
39 00 11 b1 00 11 19 0e 12 07 08 08 08 22 04 11 11 a9 32 18
|
||||
39 00 06 ff 77 01 00 00 11
|
||||
15 00 02 b0 60
|
||||
15 00 02 b1 30
|
||||
15 00 02 b2 87
|
||||
15 00 02 b3 80
|
||||
15 00 02 b5 49
|
||||
15 00 02 b7 85
|
||||
15 00 02 b8 21
|
||||
15 00 02 c1 78
|
||||
15 14 02 c2 78
|
||||
39 00 04 e0 00 1b 02
|
||||
39 00 0c e1 08 a0 00 00 07 a0 00 00 00 44 44
|
||||
39 00 0d e2 11 11 44 44 ed a0 00 00 ec a0 00 00
|
||||
39 00 05 e3 00 00 11 11
|
||||
39 00 03 e4 44 44
|
||||
39 00 11 e5 0a e9 d8 a0 0c eb d8 a0 0e ed d8 a0 10 ef d8 a0
|
||||
39 00 05 e6 00 00 11 11
|
||||
39 00 03 e7 44 44
|
||||
39 00 11 e8 09 e8 d8 a0 0b ea d8 a0 0d ec d8 a0 0f ee d8 a0
|
||||
39 00 08 eb 02 00 e4 e4 88 00 40
|
||||
39 00 03 ec 3c 00
|
||||
39 00 11 ed ab 89 76 54 02 ff ff ff ff ff ff 20 45 67 98 ba
|
||||
/*
|
||||
39 00 06 ff 77 01 00 00 12
|
||||
15 00 02 d1 81
|
||||
15 00 02 d2 08
|
||||
*/
|
||||
39 00 06 ff 77 01 00 00 00
|
||||
15 00 02 36 00
|
||||
05 c8 01 11
|
||||
05 32 01 29
|
||||
];
|
||||
|
||||
disp_timings0: display-timings {
|
||||
native-mode = <&dsi_timing0>;
|
||||
dsi_timing0: timing0 {
|
||||
clock-frequency = <20606400>;
|
||||
hactive = <480>;
|
||||
vactive = <480>;
|
||||
hfront-porch = <80>;
|
||||
hsync-len = <8>;
|
||||
hback-porch = <80>;
|
||||
vfront-porch = <18>;
|
||||
vsync-len = <2>;
|
||||
vback-porch = <30>;
|
||||
hsync-active = <0>;
|
||||
vsync-active = <0>;
|
||||
de-active = <0>;
|
||||
pixelclk-active = <0>;
|
||||
};
|
||||
};
|
||||
|
||||
ports {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
port@0 {
|
||||
reg = <0>;
|
||||
panel_in_dsi: endpoint {
|
||||
remote-endpoint = <&dsi_out_panel>;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
ports {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
port@1 {
|
||||
reg = <1>;
|
||||
dsi_out_panel: endpoint {
|
||||
remote-endpoint = <&panel_in_dsi>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
};
|
||||
|
||||
&dsi_dphy {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&dsi_in_vop {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&dsi_panel {
|
||||
power-supply = <&vcc3v3_lcd_n>;
|
||||
};
|
||||
|
||||
&fspi {
|
||||
status = "okay";
|
||||
|
||||
flash@0 {
|
||||
compatible = "spi-nand";
|
||||
reg = <0>;
|
||||
spi-max-frequency = <80000000>;
|
||||
spi-rx-bus-width = <4>;
|
||||
spi-tx-bus-width = <1>;
|
||||
};
|
||||
};
|
||||
|
||||
&gmac0 {
|
||||
phy-mode = "rmii";
|
||||
clock_in_out = "output";
|
||||
|
||||
snps,reset-gpio = <&gpio0 RK_PC3 GPIO_ACTIVE_LOW>;
|
||||
snps,reset-active-low;
|
||||
snps,reset-delays-us = <0 20000 100000>;
|
||||
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <ð_rmii0_miim_pins
|
||||
ð_rmii0_tx_bus2_pins
|
||||
ð_rmii0_rx_bus2_pins
|
||||
ð_rmii0_clk_pins>;
|
||||
|
||||
phy-handle = <&rmii_phy0>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&i2c1 {
|
||||
status = "okay";
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&rm_io25_i2c1_scl &rm_io26_i2c1_sda>;
|
||||
|
||||
ls_stk3332: light@47 {
|
||||
compatible = "ls_stk3332";
|
||||
reg = <0x47>;
|
||||
type = <SENSOR_TYPE_LIGHT>;
|
||||
irq_enable = <0>;
|
||||
als_threshold_high = <100>;
|
||||
als_threshold_low = <10>;
|
||||
als_ctrl_gain = <2>; /* 0:x1 1:x4 2:x16 3:x64 */
|
||||
poll_delay_ms = <100>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
ps_stk3332: proximity@47 {
|
||||
compatible = "ps_stk3332";
|
||||
reg = <0x47>;
|
||||
type = <SENSOR_TYPE_PROXIMITY>;
|
||||
//pinctrl-names = "default";
|
||||
//pinctrl-0 = <&stk_int_l>;
|
||||
//irq-gpio = <&gpio1 RK_PB6 IRQ_TYPE_LEVEL_LOW>;
|
||||
//irq_enable = <1>;
|
||||
ps_threshold_high = <0x64>;
|
||||
ps_threshold_low = <0x50>;
|
||||
ps_ctrl_gain = <3>; /* 0:x1 1:x2 2:x5 3:x8 */
|
||||
ps_led_current = <5>; /* 0:3.125mA 1:6.25mA 2:12.5mA 3:25mA 4:50mA 5:100mA*/
|
||||
poll_delay_ms = <100>;
|
||||
status = "okay";
|
||||
};
|
||||
};
|
||||
|
||||
&i2c2 {
|
||||
status = "okay";
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&rm_io4_i2c2_scl &rm_io5_i2c2_sda>;
|
||||
|
||||
hym8563: hym8563@51 {
|
||||
compatible = "haoyu,hym8563";
|
||||
reg = <0x51>;
|
||||
//#clock-cells = <0>;
|
||||
//clock-frequency = <32768>;
|
||||
//clock-output-names = "hym8563";
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&hym8563_int>;
|
||||
interrupt-parent = <&gpio0>;
|
||||
interrupts = <RK_PC0 IRQ_TYPE_LEVEL_LOW>;
|
||||
|
||||
wakeup-source;
|
||||
};
|
||||
|
||||
ts: ts@40 {
|
||||
compatible = "gslX680-pad";
|
||||
reg = <0x40>;
|
||||
touch-gpio = <&gpio0 RK_PA6 IRQ_TYPE_LEVEL_HIGH>;
|
||||
reset-gpio = <&gpio0 RK_PA7 IRQ_TYPE_LEVEL_HIGH>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&tp_gpio>;
|
||||
screen_max_x = <480>;
|
||||
screen_max_y = <480>;
|
||||
revert_x = <0>;
|
||||
revert_y = <0>;
|
||||
revert_xy = <1>;
|
||||
chip_id = <2>;
|
||||
status = "okay";
|
||||
};
|
||||
};
|
||||
|
||||
&mdio0 {
|
||||
rmii_phy0: phy@1 {
|
||||
compatible = "ethernet-phy-ieee802.3-c22";
|
||||
reg = <0x1>;
|
||||
};
|
||||
};
|
||||
|
||||
&pinctrl {
|
||||
/* usb {
|
||||
usb_extcon_vbus: usb-extcon-vbus {
|
||||
rockchip,pins = <1 RK_PC5 RK_FUNC_GPIO &pcfg_pull_none>;
|
||||
};
|
||||
}; */
|
||||
|
||||
hym8563 {
|
||||
hym8563_int: hy8563-int {
|
||||
rockchip,pins = <0 RK_PC0 RK_FUNC_GPIO &pcfg_pull_up>;
|
||||
};
|
||||
};
|
||||
|
||||
pmic {
|
||||
pmic_int: pmic-int {
|
||||
rockchip,pins = <0 RK_PC2 RK_FUNC_GPIO &pcfg_pull_up>;
|
||||
};
|
||||
};
|
||||
|
||||
psensor {
|
||||
stk_int_l: stk-int-l {
|
||||
rockchip,pins = <1 RK_PB6 RK_FUNC_GPIO &pcfg_pull_up>;
|
||||
};
|
||||
};
|
||||
|
||||
tp {
|
||||
tp_gpio: tp-gpio {
|
||||
rockchip,pins = <0 RK_PA6 RK_FUNC_GPIO &pcfg_pull_none>,
|
||||
<0 RK_PA7 RK_FUNC_GPIO &pcfg_pull_down>;
|
||||
};
|
||||
};
|
||||
|
||||
tsadc {
|
||||
wdt_tsadc_gpio: wdt-tsadc-gpio {
|
||||
rockchip,pins = <0 RK_PC5 RK_FUNC_GPIO &pcfg_pull_none>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&pwm0_4ch_2 {
|
||||
pinctrl-names = "active";
|
||||
pinctrl-0 = <&rm_io3_pwm0_ch2>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&rga2 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&route_dsi{
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&saradc {
|
||||
vref-supply = <&vcc_1v8>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&tsadc {
|
||||
pinctrl-names = "gpio", "otpout";
|
||||
pinctrl-0 = <&wdt_tsadc_gpio>;
|
||||
pinctrl-1 = <&rm_io21_wdt_tsadc_shut>;
|
||||
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&uart3 {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&rm_io24_uart3_ctsn &rm_io29_uart3_rtsn &rm_io30_uart3_rx &rm_io31_uart3_tx>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&uart4 {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&rm_io13_uart4_rtsn &rm_io14_uart4_tx &rm_io15_uart4_rx>;
|
||||
linux,rs485-enabled-at-boot-time;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usb20_otg0 {
|
||||
dr_mode = "peripheral";
|
||||
/* vbus-supply = <&vcc5v0_otg0>;
|
||||
rockchip,gpio-vbus-det; */
|
||||
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usb2phy {
|
||||
/* extcon = <&extcon_usb>; */
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&u2phy_otg0 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&vop {
|
||||
status = "okay";
|
||||
};
|
||||
Reference in New Issue
Block a user