arm64: dts: rockchip: rk3566-rk817-tablet bringup

Change-Id: Icd5ba7ff260e3256eaa5bb22aaf5aa93a1e4f62d
Signed-off-by: Wu Liangqing <wlq@rock-chips.com>
This commit is contained in:
Wu Liangqing
2020-11-10 17:34:12 +08:00
committed by Tao Huang
parent 0b8aec3f03
commit f15b4fc547

View File

@@ -78,6 +78,21 @@
default-brightness-level = <200>;
};
hdmi_sound: hdmi-sound {
compatible = "simple-audio-card";
simple-audio-card,format = "i2s";
simple-audio-card,mclk-fs = <256>;
simple-audio-card,name = "rockchip,hdmi";
status = "okay";
simple-audio-card,cpu {
sound-dai = <&i2s0_8ch>;
};
simple-audio-card,codec {
sound-dai = <&hdmi>;
};
};
vccsys: vccsys {
compatible = "regulator-fixed";
regulator-name = "vcc3v8_sys";
@@ -125,12 +140,25 @@
reset-gpios = <&gpio2 RK_PB1 GPIO_ACTIVE_LOW>;
};
vcc_sd: vcc-sd {
compatible = "regulator-gpio";
enable-active-low;
enable-gpio = <&gpio0 RK_PA5 GPIO_ACTIVE_LOW>;
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
pinctrl-names = "default";
pinctrl-0 = <&vcc_sd_h>;
regulator-name = "vcc_sd";
states = <3300000 0x0
3300000 0x1>;
};
wireless-wlan {
compatible = "wlan-platdata";
rockchip,grf = <&grf>;
wifi_chip_type = "ap6255";
pinctrl-names = "default";
pinctrl-0 = <&wifi_wake_h>;
pinctrl-0 = <&wifi_host_wake_irq>;
WIFI,host_wake_irq = <&gpio2 RK_PB2 GPIO_ACTIVE_HIGH>;
status = "okay";
};
@@ -164,16 +192,20 @@
backlight = <&backlight>;
power-supply=<&vcc_3v3>;
enable-gpios = <&gpio0 RK_PC7 GPIO_ACTIVE_LOW>;
enable-gpios = <&gpio0 RK_PC7 GPIO_ACTIVE_HIGH>;
stbyb-gpios = <&gpio0 RK_PC0 GPIO_ACTIVE_HIGH>;
reset-gpios = <&gpio0 RK_PC2 GPIO_ACTIVE_LOW>;
pinctrl-names = "default";
pinctrl-0 = <&lcd_enable_gpio>, <&lcd_rst_gpio>, <&lcd_stanby_gpio>;
prepare-delay-ms = <120>;
reset-delay-ms = <20>;
init-delay-ms = <20>;
stbyb-delay-ms = <10>;
enable-delay-ms = <10>;
disable-delay-ms = <20>;
unprepare-delay-ms = <20>;
reset-delay-ms = <120>;
init-delay-ms = <120>;
stbyb-delay-ms = <120>;
enable-delay-ms = <120>;
disable-delay-ms = <120>;
unprepare-delay-ms = <120>;
width-mm = <229>;
height-mm = <143>;
@@ -184,7 +216,6 @@
dsi,lanes = <4>;
panel-init-sequence = [
23 00 02 B0 01
23 00 02 C3 0F
23 00 02 C4 00
@@ -289,7 +320,7 @@
native-mode = <&timing0>;
timing0: timing0 {
clock-frequency = <152000000>;
clock-frequency = <160000000>;
hactive = <1200>;
vactive = <1920>;
@@ -307,7 +338,32 @@
pixelclk-active = <0>;
};
};
ports {
#address-cells = <1>;
#size-cells = <0>;
port@0 {
reg = <0>;
panel_in_dsi: endpoint {
remote-endpoint = <&dsi_out_panel>;
};
};
};
};
ports {
#address-cells = <1>;
#size-cells = <0>;
port@1 {
reg = <1>;
dsi_out_panel: endpoint {
remote-endpoint = <&panel_in_dsi>;
};
};
};
};
&dsi0_in_vp0 {
@@ -323,15 +379,18 @@
status = "okay";
};
&hdmi {
status = "okay";
};
&i2c0 {
status = "okay";
vdd_cpu: tcs4525@10 {
vdd_cpu: tcs4525@1c {
compatible = "tcs,tcs452x";
reg = <0x10>;
reg = <0x1c>;
vin-supply = <&vccsys>;
regulator-compatible = "fan53555-reg";
pinctrl-0 = <&soc_slppin_gpio>;
vsel-gpios = <&gpio0 2 GPIO_ACTIVE_LOW>;
regulator-name = "vdd_cpu";
regulator-min-microvolt = <712500>;
regulator-max-microvolt = <1390000>;
@@ -407,8 +466,9 @@
vdd_logic: DCDC_REG1 {
regulator-always-on;
regulator-boot-on;
regulator-min-microvolt = <900000>;
regulator-min-microvolt = <500000>;
regulator-max-microvolt = <1350000>;
regulator-init-microvolt = <900000>;
regulator-ramp-delay = <6001>;
regulator-initial-mode = <0x2>;
regulator-name = "vdd_logic";
@@ -421,8 +481,9 @@
vdd_gpu: DCDC_REG2 {
regulator-always-on;
regulator-boot-on;
regulator-min-microvolt = <900000>;
regulator-max-microvolt = <900000>;
regulator-min-microvolt = <500000>;
regulator-max-microvolt = <1350000>;
regulator-init-microvolt = <900000>;
regulator-ramp-delay = <6001>;
regulator-initial-mode = <0x2>;
regulator-name = "vdd_gpu";
@@ -442,6 +503,8 @@
};
vcc_3v3: DCDC_REG4 {
regulator-always-on;
regulator-boot-on;
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-initial-mode = <0x2>;
@@ -487,6 +550,8 @@
};
vccio_acodec: LDO_REG4 {
regulator-always-on;
regulator-boot-on;
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-name = "vccio_acodec";
@@ -498,7 +563,7 @@
vccio_sd: LDO_REG5 {
regulator-always-on;
regulator-boot-on;
regulator-min-microvolt = <3300000>;
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <3300000>;
regulator-name = "vccio_sd";
regulator-state-mem {
@@ -552,14 +617,6 @@
};
};
vcc3v3_sd: SWITCH_REG1 {
regulator-boot-on;
regulator-name = "vcc3v3_sd";
regulator-state-mem {
regulator-off-in-suspend;
};
};
dcdc_boost: BOOST {
regulator-always-on;
regulator-boot-on;
@@ -575,11 +632,11 @@
battery {
compatible = "rk817,battery";
ocv_table = <3500 3548 3592 3636 3687 3740 3780
3806 3827 3846 3864 3889 3929 3964
3993 4015 4030 4041 4056 4076 4148>;
design_capacity = <4000>;
design_qmax = <4200>;
ocv_table = <3400 3513 3578 3687 3734 3752 3763
3766 3771 3784 3804 3836 3885 3925
3962 4005 4063 4114 4169 4227 4303>;
design_capacity = <5000>;
design_qmax = <5500>;
bat_res = <100>;
sleep_enter_current = <150>;
sleep_exit_current = <180>;
@@ -597,7 +654,7 @@
min_input_voltage = <4500>;
max_input_current = <1500>;
max_chrg_current = <2000>;
max_chrg_voltage = <4200>;
max_chrg_voltage = <4300>;
chrg_term_mode = <0>;
chrg_finish_cur = <300>;
virtual_power = <0>;
@@ -610,6 +667,8 @@
compatible = "rockchip,rk817-codec";
clocks = <&cru I2S1_MCLKOUT_TX>;
clock-names = "mclk";
assigned-clocks = <&cru I2S1_MCLKOUT_TX>;
assigned-clock-parents = <&cru CLK_I2S1_8CH_TX>;
pinctrl-names = "default";
pinctrl-0 = <&i2s1mclkm0>;
hp-volume = <20>;
@@ -623,15 +682,23 @@
&i2c3 {
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&i2c3m1_xfer>;
gt1x: gt1x@14 {
compatible = "goodix,gt1x";
reg = <0x14>;
ts@40 {
compatible = "gslX680-pad";
reg = <0x40>;
touch-gpio = <&gpio3 RK_PB0 IRQ_TYPE_LEVEL_LOW>;
reset-gpio = <&gpio3 RK_PB1 IRQ_TYPE_LEVEL_HIGH>;
pinctrl-names = "default";
pinctrl-0 = <&gt1x_gpio>;
power-supply = <&vcc_3v3>;
goodix,rst-gpio = <&gpio3 RK_PB1 GPIO_ACTIVE_HIGH>;
goodix,irq-gpio = <&gpio3 RK_PB0 IRQ_TYPE_LEVEL_LOW>;
pinctrl-0 = <&tp_gpio>;
screen_max_x = <1200>;
screen_max_y = <1920>;
revert_x = <0>;
revert_y = <1>;
revert_xy = <0>;
chip_id = <1>;
status = "okay";
};
};
@@ -651,9 +718,20 @@
};
};
&i2s0_8ch {
status = "okay";
#sound-dai-cells = <0>;
};
&i2s1_8ch {
status = "okay";
#sound-dai-cells = <0>;
rockchip,clk-trcm = <1>;
pinctrl-names = "default";
pinctrl-0 = <&i2s1sclktxm0
&i2s1lrcktxm0
&i2s1sdi0m0
&i2s1sdo0m0>;
};
&jpegd {
@@ -678,10 +756,10 @@
&pinctrl {
gt1x {
gt1x_gpio: gt1x-gpio {
rockchip,pins = <3 RK_PB0 RK_FUNC_GPIO &pcfg_pull_down>,
<3 RK_PB1 RK_FUNC_GPIO &pcfg_pull_down>;
tp {
tp_gpio: tp-gpio {
rockchip,pins = <3 RK_PB0 RK_FUNC_GPIO &pcfg_pull_up>,
<3 RK_PB1 RK_FUNC_GPIO &pcfg_pull_none>;
};
};
@@ -691,6 +769,20 @@
};
};
lcd {
lcd_rst_gpio: lcd-rst-gpio {
rockchip,pins = <0 RK_PC2 RK_FUNC_GPIO &pcfg_pull_none>;
};
lcd_enable_gpio: lcd-enable-gpio {
rockchip,pins = <0 RK_PC7 RK_FUNC_GPIO &pcfg_pull_none>;
};
lcd_stanby_gpio: lcd-stanby-gpio {
rockchip,pins = <0 RK_PC0 RK_FUNC_GPIO &pcfg_pull_none>;
};
};
pmic {
pmic_int: pmic_int {
rockchip,pins =
@@ -725,9 +817,15 @@
};
};
wifi-wake {
wifi_wake_h: wifi-wake-h {
rockchip,pins = <2 RK_PB2 RK_FUNC_GPIO &pcfg_pull_none>;
vcc_sd {
vcc_sd_h: vcc-sd-h {
rockchip,pins = <0 RK_PA5 RK_FUNC_GPIO &pcfg_pull_none>;
};
};
wireless-wlan {
wifi_host_wake_irq: wifi-host-wake-irq {
rockchip,pins = <2 RK_PB2 RK_FUNC_GPIO &pcfg_pull_down>;
};
};
@@ -750,6 +848,14 @@
vccio7-supply = <&vcc_3v3>;
};
&pwm4 {
status = "okay";
};
&rk_rga {
status = "okay";
};
&rkvdec {
status = "okay";
};
@@ -773,14 +879,16 @@
&sdhci {
bus-width = <8>;
mmc-hs400-1_8v;
//mmc-hs400-1_8v;
supports-emmc;
non-removable;
keep-power-in-suspend;
max-frequency = <200000000>;
mmc-hs400-enhanced-strobe;
status = "okay";
};
&sdmmc0 {
max-frequency = <150000000>;
supports-sd;
@@ -789,9 +897,10 @@
cap-sd-highspeed;
disable-wp;
sd-uhs-sdr104;
vmmc-supply = <&vcc_sd>;
vqmmc-supply = <&vccio_sd>;
pinctrl-names = "default";
pinctrl-0 = <&sdmmc0_bus4 &sdmmc0_clk &sdmmc0_cmd &sdmmc0_pwren &sdmmc0_det>;
pinctrl-0 = <&sdmmc0_bus4 &sdmmc0_clk &sdmmc0_cmd &sdmmc0_det>;
status = "okay";
};
@@ -811,8 +920,14 @@
status = "okay";
};
&tsadc {
status = "okay";
};
&uart1 {
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&uart1m0_xfer &uart1ctsnm0>;
};
&usb2phy0 {
@@ -860,3 +975,11 @@
&vepu_mmu {
status = "okay";
};
&vop {
status = "okay";
};
&vop_mmu {
status = "okay";
};