[ Upstream commit 3cc2ffe5c1 ]
The underlying device and driver of a SCSI disk may have different
system and runtime power mode control requirements. This is because
runtime power management affects only the SCSI disk, while system level
power management affects all devices, including the controller for the
SCSI disk.
For instance, issuing a START STOP UNIT command when a SCSI disk is
runtime suspended and resumed is fine: the command is translated to a
STANDBY IMMEDIATE command to spin down the ATA disk and to a VERIFY
command to wake it up. The SCSI disk runtime operations have no effect
on the ata port device used to connect the ATA disk. However, for
system suspend/resume operations, the ATA port used to connect the
device will also be suspended and resumed, with the resume operation
requiring re-validating the device link and the device itself. In this
case, issuing a VERIFY command to spinup the disk must be done before
starting to revalidate the device, when the ata port is being resumed.
In such case, we must not allow the SCSI disk driver to issue START STOP
UNIT commands.
Allow a low level driver to refine the SCSI disk start/stop management
by differentiating system and runtime cases with two new SCSI device
flags: manage_system_start_stop and manage_runtime_start_stop. These new
flags replace the current manage_start_stop flag. Drivers setting the
manage_start_stop are modifed to set both new flags, thus preserving the
existing start/stop management behavior. For backward compatibility, the
old manage_start_stop sysfs device attribute is kept as a read-only
attribute showing a value of 1 for devices enabling both new flags and 0
otherwise.
Fixes: 0a85890559 ("ata,scsi: do not issue START STOP UNIT on resume")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Stable-dep-of: 99398d2070 ("scsi: sd: Do not issue commands to suspended disks on shutdown")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0a85890559 ]
During system resume, ata_port_pm_resume() triggers ata EH to
1) Resume the controller
2) Reset and rescan the ports
3) Revalidate devices
This EH execution is started asynchronously from ata_port_pm_resume(),
which means that when sd_resume() is executed, none or only part of the
above processing may have been executed. However, sd_resume() issues a
START STOP UNIT to wake up the drive from sleep mode. This command is
translated to ATA with ata_scsi_start_stop_xlat() and issued to the
device. However, depending on the state of execution of the EH process
and revalidation triggerred by ata_port_pm_resume(), two things may
happen:
1) The START STOP UNIT fails if it is received before the controller has
been reenabled at the beginning of the EH execution. This is visible
with error messages like:
ata10.00: device reported invalid CHS sector 0
sd 9:0:0:0: [sdc] Start/Stop Unit failed: Result: hostbyte=DID_OK driverbyte=DRIVER_OK
sd 9:0:0:0: [sdc] Sense Key : Illegal Request [current]
sd 9:0:0:0: [sdc] Add. Sense: Unaligned write command
sd 9:0:0:0: PM: dpm_run_callback(): scsi_bus_resume+0x0/0x90 returns -5
sd 9:0:0:0: PM: failed to resume async: error -5
2) The START STOP UNIT command is received while the EH process is
on-going, which mean that it is stopped and must wait for its
completion, at which point the command is rather useless as the drive
is already fully spun up already. This case results also in a
significant delay in sd_resume() which is observable by users as
the entire system resume completion is delayed.
Given that ATA devices will be woken up by libata activity on resume,
sd_resume() has no need to issue a START STOP UNIT command, which solves
the above mentioned problems. Do not issue this command by introducing
the new scsi_device flag no_start_on_resume and setting this flag to 1
in ata_scsi_dev_config(). sd_resume() is modified to issue a START STOP
UNIT command only if this flag is not set.
Reported-by: Paul Ausbeck <paula@soe.ucsc.edu>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=215880
Fixes: a19a93e4c6 ("scsi: core: pm: Rely on the device driver core for async power management")
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Tested-by: Tanner Watkins <dalzot@gmail.com>
Tested-by: Paul Ausbeck <paula@soe.ucsc.edu>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Stable-dep-of: 99398d2070 ("scsi: sd: Do not issue commands to suspended disks on shutdown")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 753a4d531b upstream.
On certain SATA controllers, softreset fails after wakeup from S2RAM with
the message "softreset failed (1st FIS failed)", sometimes resulting in
drives not being detected again. With the increased timeout, this issue
is avoided. Instead, "softreset failed (device not ready)" is now
logged 1-2 times; this later failure seems to cause fewer problems
however, and the drives are detected reliably once they've spun up and
the probe is retried.
The issue was observed with the primary SATA controller of the QNAP
TS-453B, which is an "Intel Corporation Celeron/Pentium Silver Processor
SATA Controller [8086:31e3] (rev 06)" integrated in the Celeron J4125 CPU,
and the following drives:
- Seagate IronWolf ST12000VN0008
- Seagate IronWolf ST8000NE0004
The SATA controller seems to be more relevant to this issue than the
drives, as the same drives are always detected reliably on the secondary
SATA controller on the same board (an ASMedia 106x) without any "softreset
failed" errors even without the increased timeout.
Fixes: e7d3ef13d5 ("libata: change drive ready wait after hard reset to 5s")
Cc: stable@vger.kernel.org
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1a6a464774 upstream.
Specific stress involving frequent CPU-hotplug operations, such as
running rcutorture for example, may trigger the following message:
NOHZ tick-stop error: local softirq work is pending, handler #02!!!"
This happens in the CPU-down hotplug process, after
CPUHP_AP_SMPBOOT_THREADS whose teardown callback parks ksoftirqd, and
before the target CPU shuts down through CPUHP_AP_IDLE_DEAD. In this
fragile intermediate state, softirqs waiting for threaded handling may be
forever ignored and eventually reported by the idle task as in the above
example.
However some vectors are known to be safe as long as the corresponding
subsystems have teardown callbacks handling the migration of their
events. The above error message reports pending timers softirq although
this vector can be considered as hotplug safe because the
CPUHP_TIMERS_PREPARE teardown callback performs the necessary migration
of timers after the death of the CPU. Hrtimers also have a similar
hotplug handling.
Therefore this error message, as far as (hr-)timers are concerned, can
be considered spurious and the relevant softirq vectors can be marked as
hotplug safe.
Fixes: 0345691b24 ("tick/rcu: Stop allowing RCU_SOFTIRQ in idle")
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Joel Fernandes (Google) <joel@joelfernandes.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20230912104406.312185-6-frederic@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 08713cb006 upstream.
Jakub Kicinski says:
We've got some new kdoc warnings here:
net/netfilter/nft_set_pipapo.c:1557: warning: Function parameter or member '_set' not described in 'pipapo_gc'
net/netfilter/nft_set_pipapo.c:1557: warning: Excess function parameter 'set' description in 'pipapo_gc'
include/net/netfilter/nf_tables.h:577: warning: Function parameter or member 'dead' not described in 'nft_set'
Fixes: 5f68718b34 ("netfilter: nf_tables: GC transaction API to avoid race with control plane")
Fixes: f6c383b8c3 ("netfilter: nf_tables: adapt set backend to use GC transaction API")
Reported-by: Jakub Kicinski <kuba@kernel.org>
Closes: https://lore.kernel.org/netdev/20230810104638.746e46f1@kernel.org/
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fb99ef1786 upstream.
There is no direct device ancestry defined between an ata_device and
its scsi device which prevents the power management code from correctly
ordering suspend and resume operations. Create such ancestry with the
ata device as the parent to ensure that the scsi device (child) is
suspended before the ata device and that resume handles the ata device
before the scsi device.
The parent-child (supplier-consumer) relationship is established between
the ata_port (parent) and the scsi device (child) with the function
device_add_link(). The parent used is not the ata_device as the PM
operations are defined per port and the status of all devices connected
through that port is controlled from the port operations.
The device link is established with the new function
ata_scsi_slave_alloc(), and this function is used to define the
->slave_alloc callback of the scsi host template of all ata drivers.
Fixes: a19a93e4c6 ("scsi: core: pm: Rely on the device driver core for async power management")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Niklas Cassel <niklas.cassel@wdc.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: John Garry <john.g.garry@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7cb779a686 ]
Commit 151e887d8f ("veth: Fixing transmit return status for dropped
packets") exposed the fact that bpf_clone_redirect is capable of
returning raw NET_XMIT_XXX return codes.
This is in the conflict with its UAPI doc which says the following:
"0 on success, or a negative error in case of failure."
Update the UAPI to reflect the fact that bpf_clone_redirect can
return positive error numbers, but don't explicitly define
their meaning.
Reported-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20230911194731.286342-1-sdf@google.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6a86b5b5cd ]
syzbot reported a data race splat between two processes trying to
update the same BPF map value via syscall on different CPUs:
BUG: KCSAN: data-race in bpf_percpu_array_update / bpf_percpu_array_update
write to 0xffffe8fffe7425d8 of 8 bytes by task 8257 on cpu 1:
bpf_long_memcpy include/linux/bpf.h:428 [inline]
bpf_obj_memcpy include/linux/bpf.h:441 [inline]
copy_map_value_long include/linux/bpf.h:464 [inline]
bpf_percpu_array_update+0x3bb/0x500 kernel/bpf/arraymap.c:380
bpf_map_update_value+0x190/0x370 kernel/bpf/syscall.c:175
generic_map_update_batch+0x3ae/0x4f0 kernel/bpf/syscall.c:1749
bpf_map_do_batch+0x2df/0x3d0 kernel/bpf/syscall.c:4648
__sys_bpf+0x28a/0x780
__do_sys_bpf kernel/bpf/syscall.c:5241 [inline]
__se_sys_bpf kernel/bpf/syscall.c:5239 [inline]
__x64_sys_bpf+0x43/0x50 kernel/bpf/syscall.c:5239
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x41/0xc0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
write to 0xffffe8fffe7425d8 of 8 bytes by task 8268 on cpu 0:
bpf_long_memcpy include/linux/bpf.h:428 [inline]
bpf_obj_memcpy include/linux/bpf.h:441 [inline]
copy_map_value_long include/linux/bpf.h:464 [inline]
bpf_percpu_array_update+0x3bb/0x500 kernel/bpf/arraymap.c:380
bpf_map_update_value+0x190/0x370 kernel/bpf/syscall.c:175
generic_map_update_batch+0x3ae/0x4f0 kernel/bpf/syscall.c:1749
bpf_map_do_batch+0x2df/0x3d0 kernel/bpf/syscall.c:4648
__sys_bpf+0x28a/0x780
__do_sys_bpf kernel/bpf/syscall.c:5241 [inline]
__se_sys_bpf kernel/bpf/syscall.c:5239 [inline]
__x64_sys_bpf+0x43/0x50 kernel/bpf/syscall.c:5239
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x41/0xc0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
value changed: 0x0000000000000000 -> 0xfffffff000002788
The bpf_long_memcpy is used with 8-byte aligned pointers, power-of-8 size
and forced to use long read/writes to try to atomically copy long counters.
It is best-effort only and no barriers are here since it _will_ race with
concurrent updates from BPF programs. The bpf_long_memcpy() is called from
bpf(2) syscall. Marco suggested that the best way to make this known to
KCSAN would be to use data_race() annotation.
Reported-by: syzbot+97522333291430dd277f@syzkaller.appspotmail.com
Suggested-by: Marco Elver <elver@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Marco Elver <elver@google.com>
Link: https://lore.kernel.org/bpf/000000000000d87a7f06040c970c@google.com
Link: https://lore.kernel.org/bpf/57628f7a15e20d502247c3b55fceb1cb2b31f266.1693342186.git.daniel@iogearbox.net
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 41b43b6c6e ]
It was brought up by Tetsuo that the following sequence:
write_seqlock_irqsave()
printk_deferred_enter()
could lead to a deadlock if the lockdep annotation within
write_seqlock_irqsave() triggers.
The problem is that the sequence counter is incremented before the lockdep
annotation is performed. The lockdep splat would then attempt to invoke
printk() but the reader side, of the same seqcount, could have a
tty_port::lock acquired waiting for the sequence number to become even again.
The other lockdep annotations come before the actual locking because "we
want to see the locking error before it happens". There is no reason why
seqcount should be different here.
Do the lockdep annotation first then perform the locking operation (the
sequence increment).
Fixes: 1ca7d67cf5 ("seqcount: Add lockdep functionality to seqcount/seqlock structures")
Reported-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20230920104627._DTHgPyA@linutronix.de
Closes: https://lore.kernel.org/20230621130641.-5iueY1I@linutronix.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4920327601 ]
Get a null-ptr-deref bug as follows with reproducer [1].
BUG: kernel NULL pointer dereference, address: 0000000000000228
...
RIP: 0010:vlan_dev_hard_header+0x35/0x140 [8021q]
...
Call Trace:
<TASK>
? __die+0x24/0x70
? page_fault_oops+0x82/0x150
? exc_page_fault+0x69/0x150
? asm_exc_page_fault+0x26/0x30
? vlan_dev_hard_header+0x35/0x140 [8021q]
? vlan_dev_hard_header+0x8e/0x140 [8021q]
neigh_connected_output+0xb2/0x100
ip6_finish_output2+0x1cb/0x520
? nf_hook_slow+0x43/0xc0
? ip6_mtu+0x46/0x80
ip6_finish_output+0x2a/0xb0
mld_sendpack+0x18f/0x250
mld_ifc_work+0x39/0x160
process_one_work+0x1e6/0x3f0
worker_thread+0x4d/0x2f0
? __pfx_worker_thread+0x10/0x10
kthread+0xe5/0x120
? __pfx_kthread+0x10/0x10
ret_from_fork+0x34/0x50
? __pfx_kthread+0x10/0x10
ret_from_fork_asm+0x1b/0x30
[1]
$ teamd -t team0 -d -c '{"runner": {"name": "loadbalance"}}'
$ ip link add name t-dummy type dummy
$ ip link add link t-dummy name t-dummy.100 type vlan id 100
$ ip link add name t-nlmon type nlmon
$ ip link set t-nlmon master team0
$ ip link set t-nlmon nomaster
$ ip link set t-dummy up
$ ip link set team0 up
$ ip link set t-dummy.100 down
$ ip link set t-dummy.100 master team0
When enslave a vlan device to team device and team device type is changed
from non-ether to ether, header_ops of team device is changed to
vlan_header_ops. That is incorrect and will trigger null-ptr-deref
for vlan->real_dev in vlan_dev_hard_header() because team device is not
a vlan device.
Cache eth_header_ops in team_setup(), then assign cached header_ops to
header_ops of team net device when its type is changed from non-ether
to ether to fix the bug.
Fixes: 1d76efe157 ("team: add support for non-ethernet devices")
Suggested-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20230918123011.1884401-1-william.xuanziyang@huawei.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit cf5000a778 upstream.
When more than 255 elements expired we're supposed to switch to a new gc
container structure.
This never happens: u8 type will wrap before reaching the boundary
and nft_trans_gc_space() always returns true.
This means we recycle the initial gc container structure and
lose track of the elements that came before.
While at it, don't deref 'gc' after we've passed it to call_rcu.
Fixes: 5f68718b34 ("netfilter: nf_tables: GC transaction API to avoid race with control plane")
Reported-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 4a9e12ea7e upstream.
pipapo needs to enqueue GC transactions for catchall elements through
nft_trans_gc_queue_sync(). Add nft_trans_gc_catchall_sync() and
nft_trans_gc_catchall_async() to handle GC transaction queueing
accordingly.
Fixes: 5f68718b34 ("netfilter: nf_tables: GC transaction API to avoid race with control plane")
Fixes: f6c383b8c3 ("netfilter: nf_tables: adapt set backend to use GC transaction API")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 8e51830e29 upstream.
Don't queue more gc work, else we may queue the same elements multiple
times.
If an element is flagged as dead, this can mean that either the previous
gc request was invalidated/discarded by a transaction or that the previous
request is still pending in the system work queue.
The latter will happen if the gc interval is set to a very low value,
e.g. 1ms, and system work queue is backlogged.
The sets refcount is 1 if no previous gc requeusts are queued, so add
a helper for this and skip gc run if old requests are pending.
Add a helper for this and skip the gc run in this case.
Fixes: f6c383b8c3 ("netfilter: nf_tables: adapt set backend to use GC transaction API")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit a2dd0233cb upstream.
Ditch it, it has been replace it by the GC transaction API and it has no
clients anymore.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 5f68718b34 upstream.
The set types rhashtable and rbtree use a GC worker to reclaim memory.
From system work queue, in periodic intervals, a scan of the table is
done.
The major caveat here is that the nft transaction mutex is not held.
This causes a race between control plane and GC when they attempt to
delete the same element.
We cannot grab the netlink mutex from the work queue, because the
control plane has to wait for the GC work queue in case the set is to be
removed, so we get following deadlock:
cpu 1 cpu2
GC work transaction comes in , lock nft mutex
`acquire nft mutex // BLOCKS
transaction asks to remove the set
set destruction calls cancel_work_sync()
cancel_work_sync will now block forever, because it is waiting for the
mutex the caller already owns.
This patch adds a new API that deals with garbage collection in two
steps:
1) Lockless GC of expired elements sets on the NFT_SET_ELEM_DEAD_BIT
so they are not visible via lookup. Annotate current GC sequence in
the GC transaction. Enqueue GC transaction work as soon as it is
full. If ruleset is updated, then GC transaction is aborted and
retried later.
2) GC work grabs the mutex. If GC sequence has changed then this GC
transaction lost race with control plane, abort it as it contains
stale references to objects and let GC try again later. If the
ruleset is intact, then this GC transaction deactivates and removes
the elements and it uses call_rcu() to destroy elements.
Note that no elements are removed from GC lockless path, the _DEAD bit
is set and pointers are collected. GC catchall does not remove the
elements anymore too. There is a new set->dead flag that is set on to
abort the GC transaction to deal with set->ops->destroy() path which
removes the remaining elements in the set from commit_release, where no
mutex is held.
To deal with GC when mutex is held, which allows safe deactivate and
removal, add sync GC API which releases the set element object via
call_rcu(). This is used by rbtree and pipapo backends which also
perform garbage collection from control plane path.
Since element removal from sets can happen from control plane and
element garbage collection/timeout, it is necessary to keep the set
structure alive until all elements have been deactivated and destroyed.
We cannot do a cancel_work_sync or flush_work in nft_set_destroy because
its called with the transaction mutex held, but the aforementioned async
work queue might be blocked on the very mutex that nft_set_destroy()
callchain is sitting on.
This gives us the choice of ABBA deadlock or UaF.
To avoid both, add set->refs refcount_t member. The GC API can then
increment the set refcount and release it once the elements have been
free'd.
Set backends are adapted to use the GC transaction API in a follow up
patch entitled:
("netfilter: nf_tables: use gc transaction API in set backends")
This is joint work with Florian Westphal.
Fixes: cfed7e1b1f ("netfilter: nf_tables: add set garbage collection helpers")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 806a3bc421 ]
Currently, when GETDEVICEINFO returns multiple locations where each
is a different IP but the server's identity is same as MDS, then
nfs4_set_ds_client() finds the existing nfs_client structure which
has the MDS's max_connect value (and if it's 1), then the 1st IP
on the DS's list will get dropped due to MDS trunking rules. Other
IPs would be added as they fall under the pnfs trunking rules.
For the list of IPs the 1st goes thru calling nfs4_set_ds_client()
which will eventually call nfs4_add_trunk() and call into
rpc_clnt_test_and_add_xprt() which has the check for MDS trunking.
The other IPs (after the 1st one), would call rpc_clnt_add_xprt()
which doesn't go thru that check.
nfs4_add_trunk() is called when MDS trunking is happening and it
needs to enforce the usage of max_connect mount option of the
1st mount. However, this shouldn't be applied to pnfs flow.
Instead, this patch proposed to treat MDS=DS as DS trunking and
make sure that MDS's max_connect limit does not apply to the
1st IP returned in the GETDEVICEINFO list. It does so by
marking the newly created client with a new flag NFS_CS_PNFS
which then used to pass max_connect value to use into the
rpc_clnt_test_and_add_xprt() instead of the existing rpc
client's max_connect value set by the MDS connection.
For example, mount was done without max_connect value set
so MDS's rpc client has cl_max_connect=1. Upon calling into
rpc_clnt_test_and_add_xprt() and using rpc client's value,
the caller passes in max_connect value which is previously
been set in the pnfs path (as a part of handling
GETDEVICEINFO list of IPs) in nfs4_set_ds_client().
However, when NFS_CS_PNFS flag is not set and we know we
are doing MDS trunking, comparing a new IP of the same
server, we then set the max_connect value to the
existing MDS's value and pass that into
rpc_clnt_test_and_add_xprt().
Fixes: dc48e0abee ("SUNRPC enforce creation of no more than max_connect xprts")
Signed-off-by: Olga Kornievskaia <kolga@netapp.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b193a78ddb ]
Ensure that nfs_clear_request_commit() updates the correct counters when
it removes them from the commit list.
Fixes: ed5d588fe4 ("NFS: Try to join page groups before an O_DIRECT retransmission")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 24e0e61db3 upstream.
In AHCI 1.3.1, the register description for CAP.SSC:
"When cleared to ‘0’, software must not allow the HBA to initiate
transitions to the Slumber state via agressive link power management nor
the PxCMD.ICC field in each port, and the PxSCTL.IPM field in each port
must be programmed to disallow device initiated Slumber requests."
In AHCI 1.3.1, the register description for CAP.PSC:
"When cleared to ‘0’, software must not allow the HBA to initiate
transitions to the Partial state via agressive link power management nor
the PxCMD.ICC field in each port, and the PxSCTL.IPM field in each port
must be programmed to disallow device initiated Partial requests."
Ensure that we always set the corresponding bits in PxSCTL.IPM, such that
a device is not allowed to initiate transitions to power states which are
unsupported by the HBA.
DevSleep is always initiated by the HBA, however, for completeness, set the
corresponding bit in PxSCTL.IPM such that agressive link power management
cannot transition to DevSleep if DevSleep is not supported.
sata_link_scr_lpm() is used by libahci, ata_piix and libata-pmp.
However, only libahci has the ability to read the CAP/CAP2 register to see
if these features are supported. Therefore, in order to not introduce any
regressions on ata_piix or libata-pmp, create flags that indicate that the
respective feature is NOT supported. This way, the behavior for ata_piix
and libata-pmp should remain unchanged.
This change is based on a patch originally submitted by Runa Guo-oc.
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Fixes: 1152b2617a ("libata: implement sata_link_scr_lpm() and make ata_dev_set_feature() global")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 25e73b7e3f ]
It was reported that under certain circumstances GCC emits ENDBR
instructions for _THIS_IP_ usage. Specifically, when it appears at the
start of a basic block -- but not elsewhere.
Since _THIS_IP_ is never used for control flow, these ENDBR
instructions are completely superfluous. Override the _THIS_IP_
definition for x86_64 to avoid this.
Less ENDBR instructions is better.
Fixes: 156ff4a544 ("x86/ibt: Base IBT bits")
Reported-by: David Kaplan <David.Kaplan@amd.com>
Reviewed-by: Andrew Cooper <andrew.cooper3@citrix.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20230802110323.016197440@infradead.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 12e6ac69cc ]
Some NXP processors using ChipIdea USB IP have a bug when frame babble is
detected.
Issue description:
In USB camera test, our controller is host in HS mode. In ISOC IN, when
device sends data across the micro frame, it causes the babble in host
controller. This will clear the PE bit. In spec, it also requires to set
the PEC bit and then set the PCI bit. Without the PCI interrupt, the
software does not know the PE is cleared.
This will add a flag CI_HDRC_HAS_PORTSC_PEC_MISSED to some impacted
platform datas. And the ehci host driver will assert PEC by SW when
specific conditions are satisfied.
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Link: https://lore.kernel.org/r/20230809024432.535160-2-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a7ed3465da ]
When compiling with gcc 13 and CONFIG_FORTIFY_SOURCE=y, the following
warning appears:
In function ‘fortify_memcpy_chk’,
inlined from ‘size_entry_mwt’ at net/bridge/netfilter/ebtables.c:2118:2:
./include/linux/fortify-string.h:592:25: error: call to ‘__read_overflow2_field’
declared with attribute warning: detected read beyond size of field (2nd parameter);
maybe use struct_group()? [-Werror=attribute-warning]
592 | __read_overflow2_field(q_size_field, size);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
The compiler is complaining:
memcpy(&offsets[1], &entry->watchers_offset,
sizeof(offsets) - sizeof(offsets[0]));
where memcpy reads beyong &entry->watchers_offset to copy
{watchers,target,next}_offset altogether into offsets[]. Silence the
warning by wrapping these three up via struct_group().
Signed-off-by: GONG, Ruiqi <gongruiqi1@huawei.com>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d11a69873d ]
Arm platforms use is_default_overflow_handler() to determine if the
hw_breakpoint code should single-step over the breakpoint trigger or
let the custom handler deal with it.
Since bpf_overflow_handler() currently isn't recognized as a default
handler, attaching a BPF program to a PERF_TYPE_BREAKPOINT event causes
it to keep firing (the instruction triggering the data abort exception
is never skipped). For example:
# bpftrace -e 'watchpoint:0x10000:4:w { print("hit") }' -c ./test
Attaching 1 probe...
hit
hit
[...]
^C
(./test performs a single 4-byte store to 0x10000)
This patch replaces the check with uses_default_overflow_handler(),
which accounts for the bpf_overflow_handler() case by also testing
if one of the perf_event_output functions gets invoked indirectly,
via orig_default_handler.
Signed-off-by: Tomislav Novak <tnovak@meta.com>
Tested-by: Samuel Gosselin <sgosselin@google.com> # arm64
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/linux-arm-kernel/20220923203644.2731604-1-tnovak@fb.com/
Link: https://lore.kernel.org/r/20230605191923.1219974-1-tnovak@meta.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0242737dc4 ]
Some HiSilicon SMMU PMCG suffers the erratum 162001900 that the PMU
disable control sometimes fail to disable the counters. This will lead
to error or inaccurate data since before we enable the counters the
counter's still counting for the event used in last perf session.
This patch tries to fix this by hardening the global disable process.
Before disable the PMU, writing an invalid event type (0xffff) to
focibly stop the counters. Correspondingly restore each events on
pmu::pmu_enable().
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Link: https://lore.kernel.org/r/20230814124012.58013-1-yangyicong@huawei.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d243b34459 ]
Under PREEMPT_RT, __put_task_struct() indirectly acquires sleeping
locks. Therefore, it can't be called from an non-preemptible context.
One practical example is splat inside inactive_task_timer(), which is
called in a interrupt context:
CPU: 1 PID: 2848 Comm: life Kdump: loaded Tainted: G W ---------
Hardware name: HP ProLiant DL388p Gen8, BIOS P70 07/15/2012
Call Trace:
dump_stack_lvl+0x57/0x7d
mark_lock_irq.cold+0x33/0xba
mark_lock+0x1e7/0x400
mark_usage+0x11d/0x140
__lock_acquire+0x30d/0x930
lock_acquire.part.0+0x9c/0x210
rt_spin_lock+0x27/0xe0
refill_obj_stock+0x3d/0x3a0
kmem_cache_free+0x357/0x560
inactive_task_timer+0x1ad/0x340
__run_hrtimer+0x8a/0x1a0
__hrtimer_run_queues+0x91/0x130
hrtimer_interrupt+0x10f/0x220
__sysvec_apic_timer_interrupt+0x7b/0xd0
sysvec_apic_timer_interrupt+0x4f/0xd0
asm_sysvec_apic_timer_interrupt+0x12/0x20
RIP: 0033:0x7fff196bf6f5
Instead of calling __put_task_struct() directly, we defer it using
call_rcu(). A more natural approach would use a workqueue, but since
in PREEMPT_RT, we can't allocate dynamic memory from atomic context,
the code would become more complex because we would need to put the
work_struct instance in the task_struct and initialize it when we
allocate a new task_struct.
The issue is reproducible with stress-ng:
while true; do
stress-ng --sched deadline --sched-period 1000000000 \
--sched-runtime 800000000 --sched-deadline \
1000000000 --mmapfork 23 -t 20
done
Reported-by: Hu Chunyu <chuhu@redhat.com>
Suggested-by: Oleg Nesterov <oleg@redhat.com>
Suggested-by: Valentin Schneider <vschneid@redhat.com>
Suggested-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Wander Lairson Costa <wander@redhat.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/r/20230614122323.37957-2-wander@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aa99e5f87b ]
Andrei Vagin reported bind() regression with strace logs.
If we bind() a TCPv6 socket to ::FFFF:0.0.0.0 and then bind() a TCPv4
socket to 127.0.0.1, the 2nd bind() should fail but now succeeds.
from socket import *
s1 = socket(AF_INET6, SOCK_STREAM)
s1.bind(('::ffff:0.0.0.0', 0))
s2 = socket(AF_INET, SOCK_STREAM)
s2.bind(('127.0.0.1', s1.getsockname()[1]))
During the 2nd bind(), if tb->family is AF_INET6 and sk->sk_family is
AF_INET in inet_bind2_bucket_match_addr_any(), we still need to check
if tb has the v4-mapped-v6 wildcard address.
The example above does not work after commit 5456262d2b ("net: Fix
incorrect address comparison when searching for a bind2 bucket"), but
the blamed change is not the commit.
Before the commit, the leading zeros of ::FFFF:0.0.0.0 were treated
as 0.0.0.0, and the sequence above worked by chance. Technically, this
case has been broken since bhash2 was introduced.
Note that if we bind() two sockets to 127.0.0.1 and then ::FFFF:0.0.0.0,
the 2nd bind() fails properly because we fall back to using bhash to
detect conflicts for the v4-mapped-v6 address.
Fixes: 28044fc1d4 ("net: Add a bhash2 table hashed by port and address")
Reported-by: Andrei Vagin <avagin@google.com>
Closes: https://lore.kernel.org/netdev/ZPuYBOFC8zsK6r9T@google.com/
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8cdc3223e7 ]
Some code defines the IPv6 wildcard address as a local variable and
use it with memcmp() or ipv6_addr_equal().
Let's use in6addr_any and ipv6_addr_any() instead.
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: aa99e5f87b ("tcp: Fix bind() regression for v4-mapped-v6 wildcard address.")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 271de525e1 ]
The commit 64696c40d0 ("bpf: Add __bpf_prog_{enter,exit}_struct_ops for struct_ops trampoline")
removed prog->active check for struct_ops prog. The bpf_lsm
and bpf_iter is also using trampoline. Like struct_ops, the bpf_lsm
and bpf_iter have fixed hooks for the prog to attach. The
kernel does not call the same hook in a recursive way.
This patch also removes the prog->active check for
bpf_lsm and bpf_iter.
A later patch has a test to reproduce the recursion issue
for a sleepable bpf_lsm program.
This patch appends the '_recur' naming to the existing
enter and exit functions that track the prog->active counter.
New __bpf_prog_{enter,exit}[_sleepable] function are
added to skip the prog->active tracking. The '_struct_ops'
version is also removed.
It also moves the decision on picking the enter and exit function to
the new bpf_trampoline_{enter,exit}(). It returns the '_recur' ones
for all tracing progs to use. For bpf_lsm, bpf_iter,
struct_ops (no prog->active tracking after 64696c40d0), and
bpf_lsm_cgroup (no prog->active tracking after 69fd337a97),
it will return the functions that don't track the prog->active.
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
Link: https://lore.kernel.org/r/20221025184524.3526117-2-martin.lau@linux.dev
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Stable-dep-of: 7645629f7d ("bpf: Invoke __bpf_prog_exit_sleepable_recur() on recursion in kern_sys_bpf().")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 719c5e37e9 ]
Previously, the defines for phy_device flags in the Micrel driver were
ambiguous in their representation. They were intended to be bit masks
but were mistakenly defined as bit positions. This led to the following
issues:
- MICREL_KSZ8_P1_ERRATA, designated for KSZ88xx switches, overlapped
with MICREL_PHY_FXEN and MICREL_PHY_50MHZ_CLK.
- Due to this overlap, the code path for MICREL_PHY_FXEN, tailored for
the KSZ8041 PHY, was not executed for KSZ88xx PHYs.
- Similarly, the code associated with MICREL_PHY_50MHZ_CLK wasn't
triggered for KSZ88xx.
To rectify this, all three flags have now been explicitly converted to
use the `BIT()` macro, ensuring they are defined as bit masks and
preventing potential overlaps in the future.
Fixes: 49011e0c15 ("net: phy: micrel: ksz886x/ksz8081: add cabletest support")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8423be8926 ]
Route hints when the nexthop is part of a multipath group causes packets
in the same receive batch to be sent to the same nexthop irrespective of
the multipath hash of the packet. So, do not extract route hint for
packets whose destination is part of a multipath group.
A new SKB flag IP6SKB_MULTIPATH is introduced for this purpose, set the
flag when route is looked up in fib6_select_path() and use it in
ip6_can_use_hint() to check for the existence of the flag.
Fixes: 197dbf24e3 ("ipv6: introduce and uses route look hints for list input.")
Signed-off-by: Sriram Yagnaraman <sriram.yagnaraman@est.tech>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6ac66cb03a ]
Route hints when the nexthop is part of a multipath group causes packets
in the same receive batch to be sent to the same nexthop irrespective of
the multipath hash of the packet. So, do not extract route hint for
packets whose destination is part of a multipath group.
A new SKB flag IPSKB_MULTIPATH is introduced for this purpose, set the
flag when route is looked up in ip_mkroute_input() and use it in
ip_extract_route_hint() to check for the existence of the flag.
Fixes: 02b2494161 ("ipv4: use dst hint for ipv4 list receive")
Signed-off-by: Sriram Yagnaraman <sriram.yagnaraman@est.tech>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5e6300e7b3 ]
Every time sk->sk_forward_alloc is read locklessly,
add a READ_ONCE().
Add sk_forward_alloc_add() helper to centralize updates,
to reduce number of WRITE_ONCE().
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8aae7625ff ]
New skbs allocated via nf_send_reset() have skb->dev == NULL.
fib*_rules_early_flow_dissect helpers already have a 'struct net'
argument but its not passed down to the flow dissector core, which
will then WARN as it can't derive a net namespace to use:
WARNING: CPU: 0 PID: 0 at net/core/flow_dissector.c:1016 __skb_flow_dissect+0xa91/0x1cd0
[..]
ip_route_me_harder+0x143/0x330
nf_send_reset+0x17c/0x2d0 [nf_reject_ipv4]
nft_reject_inet_eval+0xa9/0xf2 [nft_reject_inet]
nft_do_chain+0x198/0x5d0 [nf_tables]
nft_do_chain_inet+0xa4/0x110 [nf_tables]
nf_hook_slow+0x41/0xc0
ip_local_deliver+0xce/0x110
..
Cc: Stanislav Fomichev <sdf@google.com>
Cc: David Ahern <dsahern@kernel.org>
Cc: Ido Schimmel <idosch@nvidia.com>
Fixes: 812fa71f0d ("netfilter: Dissect flow after packet mangling")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=217826
Signed-off-by: Florian Westphal <fw@strlen.de>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20230830110043.30497-1-fw@strlen.de
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 5cf9d015be upstream.
After commit c28cd1f343 ("clk: Mark a fwnode as initialized when using
CLK_OF_DECLARE() macro"), drivers/clk/mvebu/kirkwood.c fails to build:
drivers/clk/mvebu/kirkwood.c:358:1: error: expected identifier or '('
CLK_OF_DECLARE(98dx1135_clk, "marvell,mv98dx1135-core-clock",
^
include/linux/clk-provider.h:1367:21: note: expanded from macro 'CLK_OF_DECLARE'
static void __init name##_of_clk_init_declare(struct device_node *np) \
^
<scratch space>:124:1: note: expanded from here
98dx1135_clk_of_clk_init_declare
^
drivers/clk/mvebu/kirkwood.c:358:1: error: invalid digit 'd' in decimal constant
include/linux/clk-provider.h:1372:34: note: expanded from macro 'CLK_OF_DECLARE'
OF_DECLARE_1(clk, name, compat, name##_of_clk_init_declare)
^
<scratch space>:125:3: note: expanded from here
98dx1135_clk_of_clk_init_declare
^
drivers/clk/mvebu/kirkwood.c:358:1: error: invalid digit 'd' in decimal constant
include/linux/clk-provider.h:1372:34: note: expanded from macro 'CLK_OF_DECLARE'
OF_DECLARE_1(clk, name, compat, name##_of_clk_init_declare)
^
<scratch space>:125:3: note: expanded from here
98dx1135_clk_of_clk_init_declare
^
drivers/clk/mvebu/kirkwood.c:358:1: error: invalid digit 'd' in decimal constant
include/linux/clk-provider.h:1372:34: note: expanded from macro 'CLK_OF_DECLARE'
OF_DECLARE_1(clk, name, compat, name##_of_clk_init_declare)
^
<scratch space>:125:3: note: expanded from here
98dx1135_clk_of_clk_init_declare
^
C function names must start with either an alphabetic letter or an
underscore. To avoid generating invalid function names from clock names,
add two underscores to the beginning of the identifier.
Fixes: c28cd1f343 ("clk: Mark a fwnode as initialized when using CLK_OF_DECLARE() macro")
Suggested-by: Saravana Kannan <saravanak@google.com>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Link: https://lore.kernel.org/r/20230308-clk_of_declare-fix-v1-1-317b741e2532@kernel.org
Reviewed-by: Saravana Kannan <saravanak@google.com>
Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c28cd1f343 upstream.
We already mark fwnodes as initialized when they are registered as clock
providers. We do this so that fw_devlink can tell when a clock driver
doesn't use the driver core framework to probe/initialize its device.
This ensures fw_devlink doesn't block the consumers of such a clock
provider indefinitely.
However, some users of CLK_OF_DECLARE() macros don't use the same node
that matches the macro as the node for the clock provider, but they
initialize the entire node. To cover these cases, also mark the nodes
that match the macros as initialized when the init callback function is
called.
An example of this is "stericsson,u8500-clks" that's handled using
CLK_OF_DECLARE() and looks something like this:
clocks {
compatible = "stericsson,u8500-clks";
prcmu_clk: prcmu-clock {
#clock-cells = <1>;
};
prcc_pclk: prcc-periph-clock {
#clock-cells = <2>;
};
prcc_kclk: prcc-kernel-clock {
#clock-cells = <2>;
};
prcc_reset: prcc-reset-controller {
#reset-cells = <2>;
};
...
};
This patch makes sure that "clocks" is marked as initialized so that
fw_devlink knows that all nodes under it have been initialized. If the
driver creates struct devices for some of the subnodes, fw_devlink is
smart enough to know to wait for those devices to probe, so no special
handling is required for those cases.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reported-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/lkml/CACRpkdamxDX6EBVjKX5=D3rkHp17f5pwGdBVhzFU90-0MHY6dQ@mail.gmail.com/
Fixes: 4a032827da ("of: property: Simplify of_link_to_phandle()")
Signed-off-by: Saravana Kannan <saravanak@google.com>
Link: https://lore.kernel.org/r/20230302014639.297514-1-saravanak@google.com
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f236433064 upstream.
Some usb hubs will negotiate DisplayPort Alt mode with the device
but will then negotiate a data role swap after entering the alt
mode. The data role swap causes the device to unregister all alt
modes, however the usb hub will still send Attention messages
even after failing to reregister the Alt Mode. type_altmode_attention
currently does not verify whether or not a device's altmode partner
exists, which results in a NULL pointer error when dereferencing
the typec_altmode and typec_altmode_ops belonging to the altmode
partner.
Verify the presence of a device's altmode partner before sending
the Attention message to the Alt Mode driver.
Fixes: 8a37d87d72 ("usb: typec: Bus type for alternate modes")
Cc: stable@vger.kernel.org
Signed-off-by: RD Babiera <rdbabiera@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20230814180559.923475-1-rdbabiera@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5cd474e573 upstream.
Interrupts are blocked in SDEI context, per the SDEI spec: "The client
interrupts cannot preempt the event handler." If we crashed in the SDEI
handler-running context (as with ACPI's AGDI) then we need to clean up the
SDEI state before proceeding to the crash kernel so that the crash kernel
can have working interrupts.
Track the active SDEI handler per-cpu so that we can COMPLETE_AND_RESUME
the handler, discarding the interrupted context.
Fixes: f5df269618 ("arm64: kernel: Add arch-specific SDEI entry code and CPU masking")
Signed-off-by: D Scott Phillips <scott@os.amperecomputing.com>
Cc: stable@vger.kernel.org
Reviewed-by: James Morse <james.morse@arm.com>
Tested-by: Mihai Carabas <mihai.carabas@oracle.com>
Link: https://lore.kernel.org/r/20230627002939.2758-1-scott@os.amperecomputing.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
