commit 6d710b769c1f5f0d55c9ad9bb49b7dce009ec103 upstream.
The original comment is confusing because it implies that variants other
than the SC16IS762 supports other SPI modes beside SPI_MODE_0.
Extract from datasheet:
The SC16IS762 differs from the SC16IS752 in that it supports SPI clock
speeds up to 15 Mbit/s instead of the 4 Mbit/s supported by the
SC16IS752... In all other aspects, the SC16IS762 is functionally and
electrically the same as the SC16IS752.
The same is also true of the SC16IS760 variant versus the SC16IS740 and
SC16IS750 variants.
For all variants, only SPI mode 0 is supported.
Change comment and abort probing if the specified SPI mode is not
SPI_MODE_0.
Fixes: 2c837a8a8f ("sc16is7xx: spi interface is added")
Cc: <stable@vger.kernel.org>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20231221231823.2327894-3-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 502296030ec6b0329e00f9fb15018e170cc63037 upstream.
There appear to be a few different ways that Wacom devices can deal with
confidence:
1. If the device looses confidence in a touch, it will first clear
the tipswitch flag in one report, and then clear the confidence
flag in a second report. This behavior is used by e.g. DTH-2452.
2. If the device looses confidence in a touch, it will clear both
the tipswitch and confidence flags within the same report. This
behavior is used by some AES devices.
3. If the device looses confidence in a touch, it will clear *only*
the confidence bit. The tipswitch bit will remain set so long as
the touch is tracked. This behavior may be used in future devices.
The driver does not currently handle situation 3 properly. Touches that
loose confidence will remain "in prox" and essentially frozen in place
until the tipswitch bit is finally cleared. Not only does this result
in userspace seeing a stuck touch, but it also prevents pen arbitration
from working properly (the pen won't send events until all touches are
up, but we don't currently process events from non-confident touches).
This commit centralizes the checking of the confidence bit in the
wacom_wac_finger_slot() function and has 'prox' depend on it. In the
case where situation 3 is encountered, the treat the touch as though
it was removed, allowing both userspace and the pen arbitration to
act normally.
Signed-off-by: Tatsunosuke Tobita <tatsunosuke.tobita@wacom.com>
Signed-off-by: Ping Cheng <ping.cheng@wacom.com>
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Fixes: 7fb0413baa ("HID: wacom: Use "Confidence" flag to prevent reporting invalid contacts")
Cc: stable@vger.kernel.org
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a25a7df518fc71b1ba981d691e9322e645d2689c upstream.
Previous version of ad7091r event handler received the ADC state pointer
and retrieved the iio device from driver data field with dev_get_drvdata().
However, no driver data have ever been set, which led to null pointer
dereference when running the event handler.
Pass the iio device to the event handler and retrieve the ADC state struct
from it so we avoid the null pointer dereference and save the driver from
filling the driver data field.
Fixes: ca69300173 ("iio: adc: Add support for AD7091R5 ADC")
Signed-off-by: Marcelo Schmitt <marcelo.schmitt@analog.com>
Link: https://lore.kernel.org/r/5024b764107463de9578d5b3b0a3d5678e307b1a.1702746240.git.marcelo.schmitt1@gmail.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ad362fe07fecf0aba839ff2cc59a3617bd42c33f upstream.
There is a potential UAF scenario in the case of an LPI translation
cache hit racing with an operation that invalidates the cache, such
as a DISCARD ITS command. The root of the problem is that
vgic_its_check_cache() does not elevate the refcount on the vgic_irq
before dropping the lock that serializes refcount changes.
Have vgic_its_check_cache() raise the refcount on the returned vgic_irq
and add the corresponding decrement after queueing the interrupt.
Cc: stable@vger.kernel.org
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20240104183233.3560639-1-oliver.upton@linux.dev
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7b95382f965133ef61ce44aaabc518c16eb46909 upstream.
When the VMM writes to ISPENDR0 to set the state pending state of
an SGI, we fail to convey this to the HW if this SGI is already
backed by a GICv4.1 vSGI.
This is a bit of a corner case, as this would only occur if the
vgic state is changed on an already running VM, but this can
apparently happen across a guest reset driven by the VMM.
Fix this by always writing out the pending_latch value to the
HW, and reseting it to false.
Reported-by: Kunkun Jiang <jiangkunkun@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Zenghui Yu <yuzenghui@huawei.com>
Cc: stable@vger.kernel.org # 5.10+
Link: https://lore.kernel.org/r/7e7f2c0c-448b-10a9-8929-4b8f4f6e2a32@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1c6d984f523f67ecfad1083bb04c55d91977bb15 upstream.
kvm_guest_cpu_offline() tries to disable kvmclock regardless if it is
present in the VM. It leads to write to a MSR that doesn't exist on some
configurations, namely in TDX guest:
unchecked MSR access error: WRMSR to 0x12 (tried to write 0x0000000000000000)
at rIP: 0xffffffff8110687c (kvmclock_disable+0x1c/0x30)
kvmclock enabling is gated by CLOCKSOURCE and CLOCKSOURCE2 KVM paravirt
features.
Do not disable kvmclock if it was not enabled.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Fixes: c02027b574 ("x86/kvm: Disable kvmclock on all CPUs on shutdown")
Reviewed-by: Sean Christopherson <seanjc@google.com>
Reviewed-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Wanpeng Li <wanpengli@tencent.com>
Cc: stable@vger.kernel.org
Message-Id: <20231205004510.27164-6-kirill.shutemov@linux.intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4e11c29873a8a296a20f99b3e03095e65ebf897d upstream.
We found a failure when using the iperf tool during WiFi performance
testing, where some MSIs were received while clearing the interrupt
status, and these MSIs cannot be serviced.
The interrupt status can be cleared even if the MSI status remains pending.
As such, given the edge-triggered interrupt type, its status should be
cleared before being dispatched to the handler of the underling device.
[kwilczynski: commit log, code comment wording]
Link: https://lore.kernel.org/linux-pci/20231211094923.31967-1-jianjun.wang@mediatek.com
Fixes: 43e6409db6 ("PCI: mediatek: Add MSI support for MT2712 and MT7622")
Signed-off-by: qizhong cheng <qizhong.cheng@mediatek.com>
Signed-off-by: Jianjun Wang <jianjun.wang@mediatek.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
[bhelgaas: rewrap comment]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2217fffcd63f86776c985d42e76daa43a56abdf1 upstream.
Commit 6f5e193bfb ("PCI: dwc: Fix dw_pcie_ep_raise_msix_irq() to get
correct MSI-X table address") modified dw_pcie_ep_raise_msix_irq() to
support iATUs which require a specific alignment.
However, this support cannot have been properly tested.
The whole point is for the iATU to map an address that is aligned,
using dw_pcie_ep_map_addr(), and then let the writel() write to
ep->msi_mem + aligned_offset.
Thus, modify the address that is mapped such that it is aligned.
With this change, dw_pcie_ep_raise_msix_irq() matches the logic in
dw_pcie_ep_raise_msi_irq().
Link: https://lore.kernel.org/linux-pci/20231128132231.2221614-1-nks@flawful.org
Fixes: 6f5e193bfb ("PCI: dwc: Fix dw_pcie_ep_raise_msix_irq() to get correct MSI-X table address")
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: stable@vger.kernel.org # 5.7
Cc: Kishon Vijay Abraham I <kishon@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d6488fee66472b468ed88d265b14aa3f04dc3bdf upstream.
The decoder_populate_targets() helper walks all of the targets in a port
and makes sure they can be looked up in @target_map. Where @target_map
is a lookup table from target position to target id (corresponding to a
cxl_dport instance). However @target_map is only responsible for
conveying the active dport instances as indicated by interleave_ways.
When nr_targets > interleave_ways it results in
decoder_populate_targets() walking off the end of the valid entries in
@target_map. Given target_map is initialized to 0 it results in the
dport lookup failing if position 0 is not mapped to a dport with an id
of 0:
cxl_port port3: Failed to populate active decoder targets
cxl_port port3: Failed to add decoder
cxl_port port3: Failed to add decoder3.0
cxl_bus_probe: cxl_port port3: probe: -6
This bug also highlights that when the decoder's ->targets[] array is
written in cxl_port_setup_targets() it is missing a hold of the
targets_lock to synchronize against sysfs readers of the target list. A
fix for that is saved for a later patch.
Fixes: a5c2580216 ("cxl/bus: Populate the target list at decoder create")
Cc: <stable@vger.kernel.org>
Signed-off-by: Huang, Ying <ying.huang@intel.com>
[djbw: rewrite the changelog, find the Fixes: tag]
Co-developed-by: Dan Williams <dan.j.williams@intel.com>
Reviewed-by: Alison Schofield <alison.schofield@intel.com>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ec4ffd100ffb396eca13ebe7d18938ea80f399c3 upstream.
This reverts commit a4abfa627c.
The patch broke:
> ip link set dummy0 up
> ip link set dummy0 master bond0 down
This last command is useful to be able to enslave an interface with only
one netlink message.
After discussion, there is no good reason to support:
> ip link set dummy0 down
> ip link set dummy0 master bond0 up
because the bond interface already set the slave up when it is up.
Cc: stable@vger.kernel.org
Fixes: a4abfa627c ("net: rtnetlink: Enslave device before bringing it up")
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Hangbin Liu <liuhangbin@gmail.com>
Link: https://lore.kernel.org/r/20240108094103.2001224-2-nicolas.dichtel@6wind.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f0dd488e11e71ac095df7638d892209c629d9af2 upstream.
AP BSSID configuration is missing at AP start. Without this fix, FW returns
STA interface MAC address after first init. When hostapd restarts, it gets MAC
address from netdev before driver sets STA MAC to netdev again. Now MAC address
between hostapd and net interface are different causes STA cannot connect to
AP. After that MAC address of uap0 mlan0 become the same. And issue disappears
after following hostapd restart (another issue is AP/STA MAC address become the
same).
This patch fixes the issue cleanly.
Signed-off-by: David Lin <yu-hao.lin@nxp.com>
Fixes: 12190c5d80 ("mwifiex: add cfg80211 start_ap and stop_ap handlers")
Cc: stable@vger.kernel.org
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Tested-by: Rafael Beims <rafael.beims@toradex.com> # Verdin iMX8MP/SD8997 SD
Acked-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20231215005118.17031-1-yu-hao.lin@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5894d0089cbc146063dcc0239a78ede0a8142efb upstream.
The rtlwifi driver comes with custom code to write into PCIe Link
Control register. RMW access for the Link Control register requires
locking that is already provided by the standard PCIe capability
accessors.
Convert the custom RMW code writing into LNKCTL register to standard
RMW capability accessors. The accesses are changed to cover the full
LNKCTL register instead of touching just a single byte of the register.
Fixes: 0c8173385e ("rtl8192ce: Add new driver")
Cc: stable@vger.kernel.org
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231124084725.12738-3-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b3943b3c2971444364e03224cfc828c5789deada upstream.
Ever since introduction in the commit 0c8173385e ("rtl8192ce: Add new
driver") the rtlwifi code has, according to comments, attempted to
disable/enable ASPM of the upstream bridge by writing into its LNKCTL
register. However, the code has never been correct because it performs
the writes to the device instead of the upstream bridge.
Worse yet, the offset where the PCIe capabilities reside is derived
from the offset of the upstream bridge. As a result, the write will use
an offset on the device that does not relate to the LNKCTL register
making the ASPM disable/enable code outright dangerous.
Because of those problems, there is no indication that the driver needs
disable/enable ASPM on the upstream bridge. As the Capabilities offset
is not correctly calculated for the write to target device's LNKCTL
register, the code is not disabling/enabling device's ASPM either.
Therefore, just remove the upstream bridge related ASPM disable/enable
code entirely.
The upstream bridge related ASPM code was the only user of the struct
mp_adapter members num4bytes, pcibridge_pciehdr_offset, and
pcibridge_linkctrlreg so those are removed as well.
Note: This change does not remove the code related to changing the
device's ASPM on purpose (which is independent of this flawed code
related to upstream bridge's ASPM).
Suggested-by: Bjorn Helgaas <bhelgaas@kernel.org>
Fixes: 0c8173385e ("rtl8192ce: Add new driver")
Fixes: 886e14b65a ("rtlwifi: Eliminate raw reads and writes from PCIe portion")
Cc: stable@vger.kernel.org
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231124084725.12738-2-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e874a79250b39447765ac13272b67ac36ccf2a75 upstream.
Commit 495184ac91 ("mt76: mt7915: add support for applying
pre-calibration data") was fundamentally broken and never worked.
The idea (before NVMEM support) was to expand the MTD function and pass
an additional offset. For normal EEPROM load the offset would always be
0. For the purpose of precal loading, an offset was passed that was
internally the size of EEPROM, since precal data is right after the
EEPROM.
Problem is that the offset value passed is never handled and is actually
overwrite by
offset = be32_to_cpup(list);
ret = mtd_read(mtd, offset, len, &retlen, eep);
resulting in the passed offset value always ingnored. (and even passing
garbage data as precal as the start of the EEPROM is getting read)
Fix this by adding to the current offset value, the offset from DT to
correctly read the piece of data at the requested location.
Cc: stable@vger.kernel.org
Fixes: 495184ac91 ("mt76: mt7915: add support for applying pre-calibration data")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit afc95681c3068956fed1241a1ff1612c066c75ac upstream.
In some cases the firmware expects cbndx 1 to be assigned to the GMU,
so we also want the default domain for the GMU to be an identy domain.
This way it does not get a context bank assigned. Without this, both
of_dma_configure() and drm/msm's iommu_domain_attach() will trigger
allocating and configuring a context bank. So GMU ends up attached to
both cbndx 1 and later cbndx 2. This arrangement seemingly confounds
and surprises the firmware if the GPU later triggers a translation
fault, resulting (on sc8280xp / lenovo x13s, at least) in the SMMU
getting wedged and the GPU stuck without memory access.
Cc: stable@vger.kernel.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/20231210180655.75542-1-robdclark@gmail.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c2396651309eba291c15e32db8fbe44c738b5921 upstream.
There has been a lingering bug in LoongArch Linux systems causing some
GCC tests to intermittently fail (see Closes link). I've made a minimal
reproducer:
zsh% cat measure.s
.align 4
.globl _start
_start:
movfcsr2gr $a0, $fcsr0
bstrpick.w $a0, $a0, 16, 16
beqz $a0, .ok
break 0
.ok:
li.w $a7, 93
syscall 0
zsh% cc mesaure.s -o measure -nostdlib
zsh% echo $((1.0/3))
0.33333333333333331
zsh% while ./measure; do ; done
This while loop should not stop as POSIX is clear that execve must set
fenv to the default, where FCSR should be zero. But in fact it will
just stop after running for a while (normally less than 30 seconds).
Note that "$((1.0/3))" is needed to reproduce this issue because it
raises FE_INVALID and makes fcsr0 non-zero.
The problem is we are currently relying on SET_PERSONALITY2() to reset
current->thread.fpu.fcsr. But SET_PERSONALITY2() is executed before
start_thread which calls lose_fpu(0). We can see if kernel preempt is
enabled, we may switch to another thread after SET_PERSONALITY2() but
before lose_fpu(0). Then bad thing happens: during the thread switch
the value of the fcsr0 register is stored into current->thread.fpu.fcsr,
making it dirty again.
The issue can be fixed by setting current->thread.fpu.fcsr after
lose_fpu(0) because lose_fpu() clears TIF_USEDFPU, then the thread
switch won't touch current->thread.fpu.fcsr.
The only other architecture setting FCSR in SET_PERSONALITY2() is MIPS.
I've ran a similar test on MIPS with mainline kernel and it turns out
MIPS is buggy, too. Anyway MIPS do this for supporting different FP
flavors (NaN encodings, etc.) which do not exist on LoongArch. So for
LoongArch, we can simply remove the current->thread.fpu.fcsr setting
from SET_PERSONALITY2() and do it in start_thread(), after lose_fpu(0).
The while loop failing with the mainline kernel has survived one hour
after this change on LoongArch.
Fixes: 803b0fc5c3 ("LoongArch: Add process management")
Closes: https://github.com/loongson-community/discussions/issues/7
Link: https://lore.kernel.org/linux-mips/7a6aa1bbdbbe2e63ae96ff163fab0349f58f1b9e.camel@xry111.site/
Cc: stable@vger.kernel.org
Signed-off-by: Xi Ruoyao <xry111@xry111.site>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 715d82ba636cb3629a6e18a33bb9dbe53f9936ee upstream.
The following case can cause a crash due to missing attach_btf:
1) load rawtp program
2) load fentry program with rawtp as target_fd
3) create tracing link for fentry program with target_fd = 0
4) repeat 3
In the end we have:
- prog->aux->dst_trampoline == NULL
- tgt_prog == NULL (because we did not provide target_fd to link_create)
- prog->aux->attach_btf == NULL (the program was loaded with attach_prog_fd=X)
- the program was loaded for tgt_prog but we have no way to find out which one
BUG: kernel NULL pointer dereference, address: 0000000000000058
Call Trace:
<TASK>
? __die+0x20/0x70
? page_fault_oops+0x15b/0x430
? fixup_exception+0x22/0x330
? exc_page_fault+0x6f/0x170
? asm_exc_page_fault+0x22/0x30
? bpf_tracing_prog_attach+0x279/0x560
? btf_obj_id+0x5/0x10
bpf_tracing_prog_attach+0x439/0x560
__sys_bpf+0x1cf4/0x2de0
__x64_sys_bpf+0x1c/0x30
do_syscall_64+0x41/0xf0
entry_SYSCALL_64_after_hwframe+0x6e/0x76
Return -EINVAL in this situation.
Fixes: f3a9507554 ("bpf: Allow trampoline re-attach for tracing and lsm programs")
Cc: stable@vger.kernel.org
Signed-off-by: Jiri Olsa <olsajiri@gmail.com>
Acked-by: Jiri Olsa <olsajiri@gmail.com>
Acked-by: Song Liu <song@kernel.org>
Signed-off-by: Dmitrii Dolgov <9erthalion6@gmail.com>
Link: https://lore.kernel.org/r/20240103190559.14750-4-9erthalion6@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit da9065caa594d19b26e1a030fd0cc27bd365d685 upstream.
In min_key_size_set():
if (val > hdev->le_max_key_size || val < SMP_MIN_ENC_KEY_SIZE)
return -EINVAL;
hci_dev_lock(hdev);
hdev->le_min_key_size = val;
hci_dev_unlock(hdev);
In max_key_size_set():
if (val > SMP_MAX_ENC_KEY_SIZE || val < hdev->le_min_key_size)
return -EINVAL;
hci_dev_lock(hdev);
hdev->le_max_key_size = val;
hci_dev_unlock(hdev);
The atomicity violation occurs due to concurrent execution of set_min and
set_max funcs.Consider a scenario where setmin writes a new, valid 'min'
value, and concurrently, setmax writes a value that is greater than the
old 'min' but smaller than the new 'min'. In this case, setmax might check
against the old 'min' value (before acquiring the lock) but write its
value after the 'min' has been updated by setmin. This leads to a
situation where the 'max' value ends up being smaller than the 'min'
value, which is an inconsistency.
This possible bug is found by an experimental static analysis tool
developed by our team, BassCheck[1]. This tool analyzes the locking APIs
to extract function pairs that can be concurrently executed, and then
analyzes the instructions in the paired functions to identify possible
concurrency bugs including data races and atomicity violations. The above
possible bug is reported when our tool analyzes the source code of
Linux 5.17.
To resolve this issue, it is suggested to encompass the validity checks
within the locked sections in both set_min and set_max funcs. The
modification ensures that the validation of 'val' against the
current min/max values is atomic, thus maintaining the integrity of the
settings. With this patch applied, our tool no longer reports the bug,
with the kernel configuration allyesconfig for x86_64. Due to the lack of
associated hardware, we cannot test the patch in runtime testing, and just
verify it according to the code logic.
[1] https://sites.google.com/view/basscheck/
Fixes: 18f81241b7 ("Bluetooth: Move {min,max}_key_size debugfs ...")
Cc: stable@vger.kernel.org
Signed-off-by: Gui-Dong Han <2045gemini@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 21528c69a0d8483f7c6345b1a0bc8d8975e9a172 upstream.
Documentation/filesystems/ramfs-rootfs-initramfs.rst states:
If CONFIG_TMPFS is enabled, rootfs will use tmpfs instead of ramfs by
default. To force ramfs, add "rootfstype=ramfs" to the kernel command
line.
This currently does not work when root= is provided since then
saved_root_name contains a string and rootfstype= is ignored. Therefore,
ramfs is currently always chosen when root= is provided.
The current behavior for rootfs's filesystem is:
root= | rootfstype= | chosen rootfs filesystem
------------+-------------+--------------------------
unspecified | unspecified | tmpfs
unspecified | tmpfs | tmpfs
unspecified | ramfs | ramfs
provided | ignored | ramfs
rootfstype= should be respected regardless whether root= is given,
as shown below:
root= | rootfstype= | chosen rootfs filesystem
------------+-------------+--------------------------
unspecified | unspecified | tmpfs (as before)
unspecified | tmpfs | tmpfs (as before)
unspecified | ramfs | ramfs (as before)
provided | unspecified | ramfs (compatibility with before)
provided | tmpfs | tmpfs (new)
provided | ramfs | ramfs (new)
This table represents the new behavior.
Fixes: 6e19eded36 ("initmpfs: use initramfs if rootfstype= or root= specified")
Cc: <stable@vger.kernel.org>
Signed-off-by: Rob Landley <rob@landley.net>
Link: https://lore.kernel.org/lkml/8244c75f-445e-b15b-9dbf-266e7ca666e2@landley.net/
Reviewed-and-Tested-by: Mimi Zohar <zohar@linux.ibm.com>
Signed-off-by: Stefan Berger <stefanb@linux.ibm.com>
Link: https://lore.kernel.org/r/20231120011248.396012-1-stefanb@linux.ibm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b1db244ffd041a49ecc9618e8feb6b5c1afcdaa7 upstream.
When deactivating the catch-all set element, check the state in the next
generation that represents this transaction.
This bug uncovered after the recent removal of the element busy mark
a2dd0233cb ("netfilter: nf_tables: remove busy mark and gc batch API").
Fixes: aaa31047a6 ("netfilter: nftables: add catch-all set element support")
Cc: stable@vger.kernel.org
Reported-by: lonial con <kongln9170@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6f64f866aa1ae6975c95d805ed51d7e9433a0016 upstream.
Before calling add partition or resize partition, there is no check
on whether the length is aligned with the logical block size.
If the logical block size of the disk is larger than 512 bytes,
then the partition size maybe not the multiple of the logical block size,
and when the last sector is read, bio_truncate() will adjust the bio size,
resulting in an IO error if the size of the read command is smaller than
the logical block size.If integrity data is supported, this will also
result in a null pointer dereference when calling bio_integrity_free.
Cc: <stable@vger.kernel.org>
Signed-off-by: Min Li <min15.li@samsung.com>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20230629142517.121241-1-min15.li@samsung.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bd1f6a31e7762ebc99b97f3eda5e5ea3708fa792 upstream.
When dGPU is put into BOCO it may be in D3cold but still able send
PME on display hotplug event. For this to work it must be enabled
as wake source from D3.
When runpm is enabled use pci_wake_from_d3() to mark wakeup as
enabled by default.
Cc: stable@vger.kernel.org # 6.1+
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 33cd6ea9c0673517cdb06ad5c915c6f22e9615fc upstream.
When framebuffer gets closed, the queued deferred IO gets cancelled. This
can cause some last display data to vanish. This is problematic for users
who send a still image to the framebuffer, then close the file: the image
may never appear.
To ensure none of display data get lost, flush the queued deferred IO
first before closing.
Another possible solution is to delete the cancel_delayed_work_sync()
instead. The difference is that the display may appear some time after
closing. However, the clearing of page mapping after this needs to be
removed too, because the page mapping is used by the deferred work. It is
not completely obvious whether it is okay to not clear the page mapping.
For a patch intended for stable trees, go with the simple and obvious
solution.
Fixes: 60b59beafb ("fbdev: mm: Deferred IO support")
Cc: stable@vger.kernel.org
Signed-off-by: Nam Cao <namcao@linutronix.de>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 15e4c1f462279b4e128f27de48133e0debe9e0df upstream.
The driver's fsync() is supposed to flush any pending operation to
hardware. It is implemented in this driver by cancelling the queued
deferred IO first, then schedule it for "immediate execution" by calling
schedule_delayed_work() again with delay=0. However, setting delay=0
only means the work is scheduled immediately, it does not mean the work
is executed immediately. There is no guarantee that the work is finished
after schedule_delayed_work() returns. After this driver's fsync()
returns, there can still be pending work. Furthermore, if close() is
called by users immediately after fsync(), the pending work gets
cancelled and fsync() may do nothing.
To ensure that the deferred IO completes, use flush_delayed_work()
instead. Write operations to this driver either write to the device
directly, or invoke schedule_delayed_work(); so by flushing the
workqueue, it can be guaranteed that all previous writes make it to the
device.
Fixes: 5e841b88d2 ("fb: fsync() method for deferred I/O flush.")
Cc: stable@vger.kernel.org
Signed-off-by: Nam Cao <namcao@linutronix.de>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0a535eddbe0dc1de4386046ab849f08aeb2f8faf upstream.
If IOSQE_ASYNC is set and we fail importing an iovec for a readv or
writev request, then we leave ->bytes_done uninitialized and hence the
eventual failure CQE posted can potentially have a random res value
rather than the expected -EINVAL.
Setup ->bytes_done before potentially failing, so we have a consistent
value if we fail the request early.
Cc: stable@vger.kernel.org
Reported-by: xingwei lee <xrivendell7@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 77bebd186442a7d703b796784db7495129cc3e70 upstream.
When smb2 leases is disable, ksmbd can send oplock break notification
and cause wait oplock break ack timeout. It may appear like hang when
accessing a directory. This patch make only v2 leases handle the
directory.
Cc: stable@vger.kernel.org
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 51f93776b84dee23e44a7be880736669a01cec2b upstream.
The drivers RS485 support is deactivated if there is no RTS GPIO available.
This is done by nullifying the ports rs485_supported struct. After that
however the settings in serial_omap_rs485_supported are assigned to the
same structure unconditionally, which results in an unintended reactivation
of RS485 support.
Fix this by moving the assignment to the beginning of
serial_omap_probe_rs485() and thus before uart_get_rs485_mode() gets
called.
Also replace the assignment of rs485_config() to have the complete RS485
setup in one function.
Fixes: e2752ae3cf ("serial: omap: Disallow RS-485 if rts-gpio is not specified")
Cc: <stable@vger.kernel.org>
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20240103061818.564-7-l.sanfilippo@kunbus.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0c2a5f471ce58bca8f8ab5fcb911aff91eaaa5eb upstream.
The UART supports an auto-RTS mode in which the RTS pin is automatically
activated during transmission. So mark this mode as being supported even
if RTS is not controlled by the driver but the UART.
Also the serial core expects now at least one of both modes rts-on-send or
rts-after-send to be supported. This is since during sanitization
unsupported flags are deleted from a RS485 configuration set by userspace.
However if the configuration ends up with both flags unset, the core prints
a warning since it considers such a configuration invalid (see
uart_sanitize_serial_rs485()).
Cc: <stable@vger.kernel.org>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Link: https://lore.kernel.org/r/20240103061818.564-8-l.sanfilippo@kunbus.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
