[ Upstream commit c1a6edf3b541e44e78f10bc6024df779715723f1 ]
Call runtime_pm_put*() if watchdog is not already started during probe and re
enable it in watchdog start as required.
On K3 SoCs, watchdogs and their corresponding CPUs are under same
power-domain, so if the reference count of unused watchdogs aren't
dropped, it will lead to CPU hotplug failures as Device Management
firmware won't allow to turn off the power-domain due to dangling
reference count.
Fixes: 2d63908bdb ("watchdog: Add K3 RTI watchdog support")
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Tested-by: Manorit Chawdhry <m-chawdhry@ti.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20231213140110.938129-1-vigneshr@ti.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f33f5b1fd1be5f5106d16f831309648cb0f1c31d ]
Users report about the unexpected behavior for setting timeouts above
15 sec on Raspberry Pi. According to watchdog-api.rst the ioctl
WDIOC_SETTIMEOUT shouldn't fail because of hardware limitations.
But looking at the code shows that max_timeout based on the
register value PM_WDOG_TIME_SET, which is the maximum.
Since 664a39236e ("watchdog: Introduce hardware maximum heartbeat
in watchdog core") the watchdog core is able to handle this problem.
This fix has been tested with watchdog-test from selftests.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=217374
Fixes: 664a39236e ("watchdog: Introduce hardware maximum heartbeat in watchdog core")
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20231112173251.4827-1-wahrenst@gmx.net
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dced0b3e51dd2af3730efe14dd86b5e3173f0a65 ]
Avoid unnecessary crashes by claiming only NMIs that are due to
ERROR signalling or generated by the hpwdt hardware device.
The code does this, but only for iLO5.
The intent was to preserve legacy, Gen9 and earlier, semantics of
using hpwdt for error containtment as hardware/firmware would signal
fatal IO errors as an NMI with the expectation of hpwdt crashing
the system. Howerver, these IO errors should be received by hpwdt
as an NMI_IO_CHECK. So the test is overly permissive and should
not be limited to only ilo5.
We need to enable this protection for future iLOs not matching the
current PCI IDs.
Fixes: 62290a5c19 ("watchdog: hpwdt: Claim NMIs generated by iLO5")
Signed-off-by: Jerry Hoemann <jerry.hoemann@hpe.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20231213215340.495734-2-jerry.hoemann@hpe.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 38d75297745f04206db9c29bdd75557f0344c7cc ]
When the new watchdog character device is registered, it becomes
available for opening. This creates a race where userspace may open the
device before the character device's owner is set. This results in an
imbalance in module_get calls as the cdev_get in cdev_open will not
increment the reference count on the watchdog driver module.
This causes problems when the watchdog character device is released as
the module loader's reference will also be released. This makes it
impossible to open the watchdog device later on as it now appears that
the module is being unloaded. The open will fail with -ENXIO from
chrdev_open.
The legacy watchdog device will fail with -EBUSY from the try_module_get
in watchdog_open because it's module owner is the watchdog core module
so it can still be opened but it will fail to get a refcount on the
underlying watchdog device driver.
Fixes: 72139dfa24 ("watchdog: Fix the race between the release of watchdog_core_data and cdev")
Signed-off-by: Curtis Klein <curtis.klein@hpe.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20231205190522.55153-1-curtis.klein@hpe.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1fe15be1fb613534ecbac5f8c3f8744f757d237d ]
Currently zynqmp divider round rate is considering single parent and
calculating rate and parent rate accordingly. But if divider clock flag
is set to SET_RATE_PARENT then its not trying to traverse through all
parent rate and not selecting best parent rate from that. So use common
divider_round_rate() which is traversing through all clock parents and
its rate and calculating proper parent rate.
Fixes: 3fde0e16d0 ("drivers: clk: Add ZynqMP clock driver")
Signed-off-by: Jay Buddhabhatti <jay.buddhabhatti@amd.com>
Link: https://lore.kernel.org/r/20231129112916.23125-3-jay.buddhabhatti@amd.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b782921ddd7f84f524723090377903f399fdbbcb ]
Currently zynqmp clock driver is not calculating closest mux rate and
because of that Linux is not setting proper frequency for CPU and
not able to set given frequency for dynamic frequency scaling.
E.g., In current logic initial acpu clock parent and frequency as below
apll1 0 0 0 2199999978 0 0 50000 Y
acpu0_mux 0 0 0 2199999978 0 0 50000 Y
acpu0_idiv1 0 0 0 2199999978 0 0 50000 Y
acpu0 0 0 0 2199999978 0 0 50000 Y
After changing acpu frequency to 549999994 Hz using CPU freq scaling its
selecting incorrect parent which is not closest frequency.
rpll_to_xpd 0 0 0 1599999984 0 0 50000 Y
acpu0_mux 0 0 0 1599999984 0 0 50000 Y
acpu0_div1 0 0 0 533333328 0 0 50000 Y
acpu0 0 0 0 533333328 0 0 50000 Y
Parent should remain same since 549999994 = 2199999978 / 4.
So use __clk_mux_determine_rate_closest() generic function to calculate
closest rate for mux clock. After this change its selecting correct
parent and correct clock rate.
apll1 0 0 0 2199999978 0 0 50000 Y
acpu0_mux 0 0 0 2199999978 0 0 50000 Y
acpu0_div1 0 0 0 549999995 0 0 50000 Y
acpu0 0 0 0 549999995 0 0 50000 Y
Fixes: 3fde0e16d0 ("drivers: clk: Add ZynqMP clock driver")
Signed-off-by: Jay Buddhabhatti <jay.buddhabhatti@amd.com>
Link: https://lore.kernel.org/r/20231129112916.23125-2-jay.buddhabhatti@amd.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 86d7d57a3f096c8349b32a0cd5f6f314e4416a6d ]
Should check return value of f2fs_recover_xattr_data in
__f2fs_setxattr rather than doing invalid retry if error happen.
Also just do set_page_dirty in f2fs_recover_xattr_data when
page is changed really.
Fixes: 50a472bbc79f ("f2fs: do not return EFSCORRUPTED, but try to run online repair")
Signed-off-by: Zhiguo Niu <zhiguo.niu@unisoc.com>
Reviewed-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a6582701178a47c4d0cb2188c965c59c0c0647c8 ]
The amdgpu_free_extended_power_table is called in every error-handling
paths of amdgpu_parse_extended_power_table. However, after the following
call chain of returning:
amdgpu_parse_extended_power_table
|-> kv_dpm_init / si_dpm_init
(the only two caller of amdgpu_parse_extended_power_table)
|-> kv_dpm_sw_init / si_dpm_sw_init
(the only caller of kv_dpm_init / si_dpm_init, accordingly)
|-> kv_dpm_fini / si_dpm_fini
(goto dpm_failed in xx_dpm_sw_init)
|-> amdgpu_free_extended_power_table
As above, the amdgpu_free_extended_power_table is called twice in this
returning chain and thus a double-free is triggered. Similarily, the
last kfree in amdgpu_parse_extended_power_table also cause a double free
with amdgpu_free_extended_power_table in kv_dpm_fini.
Fixes: 84176663e7 ("drm/amd/pm: create a new holder for those APIs used only by legacy ASICs(si/kv)")
Signed-off-by: Zhipeng Lu <alexious@zju.edu.cn>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c2709b2d6a537ca0fa0f1da36fdaf07e48ef447d ]
When radeon_bo_create and radeon_vm_clear_bo fail, the vm->page_tables
allocated before need to be freed. However, neither radeon_vm_init
itself nor its caller have done such deallocation.
Fixes: 6d2f2944e9 ("drm/radeon: use normal BOs for the page tables v4")
Signed-off-by: Zhipeng Lu <alexious@zju.edu.cn>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 28dd788382c43b330480f57cd34cde0840896743 ]
When ps allocated by kzalloc equals to NULL, kv_parse_power_table
frees adev->pm.dpm.ps that allocated before. However, after the control
flow goes through the following call chains:
kv_parse_power_table
|-> kv_dpm_init
|-> kv_dpm_sw_init
|-> kv_dpm_fini
The adev->pm.dpm.ps is used in the for loop of kv_dpm_fini after its
first free in kv_parse_power_table and causes a use-after-free bug.
Fixes: a2e73f56fa ("drm/amdgpu: Add support for CIK parts")
Signed-off-by: Zhipeng Lu <alexious@zju.edu.cn>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ac16667237a82e2597e329eb9bc520d1cf9dff30 ]
When the allocation of
adev->pm.dpm.dyn_state.vddc_dependency_on_dispclk.entries fails,
amdgpu_free_extended_power_table is called to free some fields of adev.
However, when the control flow returns to si_dpm_sw_init, it goes to
label dpm_failed and calls si_dpm_fini, which calls
amdgpu_free_extended_power_table again and free those fields again. Thus
a double-free is triggered.
Fixes: 841686df9f ("drm/amdgpu: add SI DPM support (v4)")
Signed-off-by: Zhipeng Lu <alexious@zju.edu.cn>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit afe58346d5d3887b3e49ff623d2f2e471f232a8d ]
Should be -EOPNOTSUPP.
Fixes: 5104fdf50d32 ("drm/amdgpu: Fix a null pointer access when the smc_rreg pointer is NULL")
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit da235d2fac212d0add570e755feb1167a830bc99 ]
The hardware manual of both RZ/G2L and RZ/G3S specifies that the reset
monitor registers need to be interrogated when the reset signals are
toggled (chapters "Procedures for Supplying and Stopping Reset Signals"
and "Procedure for Activating Modules"). Without this, there is a
chance that different modules (e.g. Ethernet) are not ready after their
reset signal is toggled, leading to failures (on probe or resume from
deep sleep states).
The same indications are available for RZ/V2M for TYPE-B reset controls.
Fixes: ef3c613ccd ("clk: renesas: Add CPG core wrapper for RZ/G2L SoC")
Fixes: 8090bea324 ("clk: renesas: rzg2l: Add support for RZ/V2M reset monitor reg")
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20231207070700.4156557-2-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5b2f885e2f6f482d05c23f04c8240f7b4fc5bdb5 ]
If an error occurs after a successful i2c_mux_add_adapter(), then
i2c_mux_del_adapters() should be called to free some resources, as
already done in the remove function.
Fixes: e6089feca4 ("media: m88ds3103: Add support for ds3103b demod")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bb34cc6ca87ff78f9fb5913d7619dc1389554da6 ]
In f2fs_filemap_fault(), it fixes to update iostat info only if
VM_FAULT_LOCKED is tagged in return value of filemap_fault().
Fixes: 8b83ac81f4 ("f2fs: support read iostat")
Signed-off-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fb9b65340c818875ea86464faf3c744bdce0055c ]
f2fs_move_file_range() doesn't support migrating compressed cluster
data, let's add the missing check condition and return -EOPNOTSUPP
for the case until we support it.
Fixes: 4c8ff7095b ("f2fs: support data compression")
Signed-off-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 55fdc1c24a1d6229fe0ecf31335fb9a2eceaaa00 ]
If inode is compressed, but not encrypted, it missed to call
f2fs_wait_on_block_writeback() to wait for GCed page writeback
in IPU write path.
Thread A GC-Thread
- f2fs_gc
- do_garbage_collect
- gc_data_segment
- move_data_block
- f2fs_submit_page_write
migrate normal cluster's block via
meta_inode's page cache
- f2fs_write_single_data_page
- f2fs_do_write_data_page
- f2fs_inplace_write_data
- f2fs_submit_page_bio
IRQ
- f2fs_read_end_io
IRQ
old data overrides new data due to
out-of-order GC and common IO.
- f2fs_read_end_io
Fixes: 4c8ff7095b ("f2fs: support data compression")
Signed-off-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5705b0e0eb550ff834125a46a4ef99b62093d83d ]
The driver always calls mipi_csis_runtime_suspend() and
mipi_csis_clk_disable() in remove(). This causes multiple WARNs from the
kernel, as the clocks get disabled too many times.
Fix the remove() to call mipi_csis_runtime_suspend() and
mipi_csis_clk_disable() in a way that reverses what is done in probe().
Link: https://lore.kernel.org/r/20231122-imx-csis-v2-1-e44b8dc4cb66@ideasonboard.com
Fixes: 7807063b86 ("media: staging/imx7: add MIPI CSI-2 receiver subdev for i.MX7")
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5d3c8990e2bbf929cb211563dadd70708f42e4e6 ]
The dma_q->p_left_data alloced by kzalloc should be freed in all the
following error handling paths. However, it hasn't been freed in the
allocation error paths of dev->video_mode.isoc_ctl.urb and
dev->video_mode.isoc_ctl.transfer_buffer.
On the other hand, the dma_q->p_left_data did be freed in the
error-handling paths after that of dev->video_mode.isoc_ctl.urb and
dev->video_mode.isoc_ctl.transfer_buffer, by calling
cx231xx_uninit_isoc(dev). So the same free operation should be done in
error-handling paths of those two allocation.
Fixes: 64fbf44455 ("[media] cx231xx: Added support for Carraera, Shelby, RDx_253S and VIDEO_GRABBER")
Signed-off-by: Zhipeng Lu <alexious@zju.edu.cn>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 28c28d7f77c06ac2c0b8f9c82bc04eba22912b3b ]
The rdev->pm.dpm.ps allocated by kcalloc should be freed in every
following error-handling path. However, in the error-handling of
rdev->pm.power_state[i].clock_info the rdev->pm.dpm.ps is not freed,
resulting in a memleak in this function.
Fixes: d70229f704 ("drm/radeon/kms: add dpm support for trinity asics")
Signed-off-by: Zhipeng Lu <alexious@zju.edu.cn>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0737df9ed0997f5b8addd6e2b9699a8c6edba2e4 ]
The rdev->pm.dpm.ps allocated by kcalloc should be freed in every
following error-handling path. However, in the error-handling of
rdev->pm.power_state[i].clock_info the rdev->pm.dpm.ps is not freed,
resulting in a memleak in this function.
Fixes: 80ea2c129c ("drm/radeon/kms: add dpm support for sumo asics (v2)")
Signed-off-by: Zhipeng Lu <alexious@zju.edu.cn>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a4f5892914ca7709ea6d191f0edace93a5935966 ]
Some SoCs may be equipped with a GPU containing two core groups
and this is exactly the case of Samsung's Exynos 5422 featuring
an ARM Mali-T628 MP6 GPU: the support for this GPU in Panfrost
is partial, as this driver currently supports using only one
core group and that's reflected on all parts of it, including
the power on (and power off, previously to this patch) function.
The issue with this is that even though executing the soft reset
operation should power off all cores unconditionally, on at least
one platform we're seeing a crash that seems to be happening due
to an interrupt firing which may be because we are calling power
transition only on the first core group, leaving the second one
unchanged, or because ISR execution was pending before entering
the panfrost_gpu_power_off() function and executed after powering
off the GPU cores, or all of the above.
Finally, solve this by:
- Avoid to enable the power transition interrupt on reset; and
- Ignoring the core_mask and ask the GPU to poweroff both core groups
Fixes: 22aa1a209018 ("drm/panfrost: Really power off GPU cores in panfrost_gpu_power_off()")
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Steven Price <steven.price@arm.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231204114215.54575-2-angelogioacchino.delregno@collabora.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a6122b0b4211d132934ef99e7b737910e6d54d2f ]
This driver includes the legacy GPIO APIs <linux/gpio.h> and
<linux/of_gpio.h> but does not use any symbols from any of
them.
Drop the includes.
Further the driver is requesting "reset-gpios" rather than
just "reset" from the GPIO framework. This is wrong because
the gpiolib core will add "-gpios" before processing the
request from e.g. device tree. Drop the suffix.
The last problem means that the optional RESET GPIO has
never been properly retrieved and used even if it existed,
but nobody noticed.
Fixes: c1124c09e1 ("ASoC: cs35l34: Initial commit of the cs35l34 CODEC driver.")
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20231201-descriptors-sound-cirrus-v2-3-ee9f9d4655eb@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 50678d339d670a92658e5538ebee30447c88ccb3 ]
This driver includes the legacy GPIO APIs <linux/gpio.h> and
<linux/of_gpio.h> but does not use any symbols from any of
them.
Drop the includes.
Further the driver is requesting "reset-gpios" rather than
just "reset" from the GPIO framework. This is wrong because
the gpiolib core will add "-gpios" before processing the
request from e.g. device tree. Drop the suffix.
The last problem means that the optional RESET GPIO has
never been properly retrieved and used even if it existed,
but nobody noticed.
Fixes: 3333cb7187 ("ASoC: cs35l33: Initial commit of the cs35l33 CODEC driver.")
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20231201-descriptors-sound-cirrus-v2-2-ee9f9d4655eb@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bc288a927815efcf9d7f4a54d4d89c5df478c635 ]
The probe function calls dispc_softreset() before runtime PM is enabled
and without enabling any of the DSS clocks. This happens to work by
luck, and we need to make sure the DSS HW is active and the fclk is
enabled.
To fix the above, add a new function, dispc_init_hw(), which does:
- pm_runtime_set_active()
- clk_prepare_enable(fclk)
- dispc_softreset().
This ensures that the reset can be successfully accomplished.
Note that we use pm_runtime_set_active(), not the normal
pm_runtime_get(). The reason for this is that at this point we haven't
enabled the runtime PM yet and also we don't want the normal resume
callback to be called: the dispc resume callback does some initial HW
setup, and it expects that the HW was off (no video ports are
streaming). If the bootloader has enabled the DSS and has set up a
boot time splash-screen, the DSS would be enabled and streaming which
might lead to issues with the normal resume callback.
Fixes: c9b2d923be ("drm/tidss: Soft Reset DISPC on startup")
Reviewed-by: Aradhya Bhatia <a-bhatia1@ti.com>
Link: https://lore.kernel.org/r/20231109-tidss-probe-v2-8-ac91b5ea35c0@ideasonboard.com
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 36d1e0852680aa038e2428d450673390111b165c ]
We do a DSS reset in the middle of the dispc_init(). While that happens
to work now, we should really make sure that e..g the fclk, which is
acquired only later in the function, is enabled when doing a reset. This
will be handled in a later patch, but for now, let's move the
dispc_softreset() call to the end of dispc_init(), which is a sensible
place for it anyway.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Aradhya Bhatia <a-bhatia1@ti.com>
Link: https://lore.kernel.org/r/20231109-tidss-probe-v2-4-ac91b5ea35c0@ideasonboard.com
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Stable-dep-of: bc288a927815 ("drm/tidss: Fix dss reset")
Signed-off-by: Sasha Levin <sashal@kernel.org>
