[ Upstream commit eca5bd666b ]
This commit fixes a race between completion of stop command and start of a
new command.
Previously the command ready interrupt was enabled before stop command
was written to the command register. This caused the command ready
interrupt to fire immediately since the CMDRDY flag is asserted constantly
while there is no command in progress.
Consequently the command state machine will immediately advance to the
next state when the tasklet function is executed again, no matter
actual completion state of the stop command.
Thus a new command can then be dispatched immediately, interrupting and
corrupting the stop command on the CMD line.
Fix that by dropping the command ready interrupt enable before calling
atmci_send_stop_cmd. atmci_send_stop_cmd does already enable the
command ready interrupt, no further writes to ATMCI_IER are necessary.
Signed-off-by: Tobias Schramm <t.schramm@manjaro.org>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Link: https://lore.kernel.org/r/20221230194315.809903-2-t.schramm@manjaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit efbcbb12ee ]
The __find_restype() function loops over the m5mols_default_ffmt[]
array, and the termination condition ends up being wrong: instead of
stopping when the iterator becomes the size of the array it traverses,
it stops after it has already overshot the array.
Now, in practice this doesn't likely matter, because the code will
always find the entry it looks for, and will thus return early and never
hit that last extra iteration.
But it turns out that clang will unroll the loop fully, because it has
only two iterations (well, three due to the off-by-one bug), and then
clang will end up just giving up in the middle of the loop unrolling
when it notices that the code walks past the end of the array.
And that made 'objtool' very unhappy indeed, because the generated code
just falls off the edge of the universe, and ends up falling through to
the next function, causing this warning:
drivers/media/i2c/m5mols/m5mols.o: warning: objtool: m5mols_set_fmt() falls through to next function m5mols_get_frame_desc()
Fix the loop ending condition.
Reported-by: Jens Axboe <axboe@kernel.dk>
Analyzed-by: Miguel Ojeda <miguel.ojeda.sandonis@gmail.com>
Analyzed-by: Nick Desaulniers <ndesaulniers@google.com>
Link: https://lore.kernel.org/linux-block/CAHk-=wgTSdKYbmB1JYM5vmHMcD9J9UZr0mn7BOYM_LudrP+Xvw@mail.gmail.com/
Fixes: bc125106f8 ("[media] Add support for M-5MOLS 8 Mega Pixel camera ISP")
Cc: HeungJun, Kim <riverful.kim@samsung.com>
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cb090e64cf ]
In xgene_hwmon_probe, &ctx->workq is bound with xgene_hwmon_evt_work.
Then it will be started.
If we remove the driver which will call xgene_hwmon_remove to clean up,
there may be unfinished work.
The possible sequence is as follows:
Fix it by finishing the work before cleanup in xgene_hwmon_remove.
CPU0 CPU1
|xgene_hwmon_evt_work
xgene_hwmon_remove |
kfifo_free(&ctx->async_msg_fifo);|
|
|kfifo_out_spinlocked
|//use &ctx->async_msg_fifo
Fixes: 2ca492e22c ("hwmon: (xgene) Fix crash when alarm occurs before driver probe")
Signed-off-by: Zheng Wang <zyytlz.wz@163.com>
Link: https://lore.kernel.org/r/20230310084007.1403388-1-zyytlz.wz@163.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 90de546d9a ]
In vnet_port_probe() and vsw_port_probe(), we should
check the return value of mdesc_grab() as it may
return NULL which can caused NPD bugs.
Fixes: 5d01fa0c6b ("ldmvsw: Add ldmvsw.c driver code")
Fixes: 43fdf27470 ("[SPARC64]: Abstract out mdesc accesses for better MD update handling.")
Signed-off-by: Liang He <windhl@126.com>
Reviewed-by: Piotr Raczynski <piotr.raczynski@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3d87debb8e ]
iucv_irq_data needs to be 4 bytes larger.
These bytes are not used by the iucv module, but written by
the z/VM hypervisor in case a CPU is deconfigured.
Reported as:
BUG dma-kmalloc-64 (Not tainted): kmalloc Redzone overwritten
-----------------------------------------------------------------------------
0x0000000000400564-0x0000000000400567 @offset=1380. First byte 0x80 instead of 0xcc
Allocated in iucv_cpu_prepare+0x44/0xd0 age=167839 cpu=2 pid=1
__kmem_cache_alloc_node+0x166/0x450
kmalloc_node_trace+0x3a/0x70
iucv_cpu_prepare+0x44/0xd0
cpuhp_invoke_callback+0x156/0x2f0
cpuhp_issue_call+0xf0/0x298
__cpuhp_setup_state_cpuslocked+0x136/0x338
__cpuhp_setup_state+0xf4/0x288
iucv_init+0xf4/0x280
do_one_initcall+0x78/0x390
do_initcalls+0x11a/0x140
kernel_init_freeable+0x25e/0x2a0
kernel_init+0x2e/0x170
__ret_from_fork+0x3c/0x58
ret_from_fork+0xa/0x40
Freed in iucv_init+0x92/0x280 age=167839 cpu=2 pid=1
__kmem_cache_free+0x308/0x358
iucv_init+0x92/0x280
do_one_initcall+0x78/0x390
do_initcalls+0x11a/0x140
kernel_init_freeable+0x25e/0x2a0
kernel_init+0x2e/0x170
__ret_from_fork+0x3c/0x58
ret_from_fork+0xa/0x40
Slab 0x0000037200010000 objects=32 used=30 fp=0x0000000000400640 flags=0x1ffff00000010200(slab|head|node=0|zone=0|
Object 0x0000000000400540 @offset=1344 fp=0x0000000000000000
Redzone 0000000000400500: cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc ................
Redzone 0000000000400510: cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc ................
Redzone 0000000000400520: cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc ................
Redzone 0000000000400530: cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc ................
Object 0000000000400540: 00 01 00 03 00 00 00 00 00 00 00 00 00 00 00 00 ................
Object 0000000000400550: f3 86 81 f2 f4 82 f8 82 f0 f0 f0 f0 f0 f0 f0 f2 ................
Object 0000000000400560: 00 00 00 00 80 00 00 00 cc cc cc cc cc cc cc cc ................
Object 0000000000400570: cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc ................
Redzone 0000000000400580: cc cc cc cc cc cc cc cc ........
Padding 00000000004005d4: 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a ZZZZZZZZZZZZZZZZ
Padding 00000000004005e4: 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a ZZZZZZZZZZZZZZZZ
Padding 00000000004005f4: 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a ZZZZZZZZZZZZ
CPU: 6 PID: 121030 Comm: 116-pai-crypto. Not tainted 6.3.0-20230221.rc0.git4.99b8246b2d71.300.fc37.s390x+debug #1
Hardware name: IBM 3931 A01 704 (z/VM 7.3.0)
Call Trace:
[<000000032aa034ec>] dump_stack_lvl+0xac/0x100
[<0000000329f5a6cc>] check_bytes_and_report+0x104/0x140
[<0000000329f5aa78>] check_object+0x370/0x3c0
[<0000000329f5ede6>] free_debug_processing+0x15e/0x348
[<0000000329f5f06a>] free_to_partial_list+0x9a/0x2f0
[<0000000329f5f4a4>] __slab_free+0x1e4/0x3a8
[<0000000329f61768>] __kmem_cache_free+0x308/0x358
[<000000032a91465c>] iucv_cpu_dead+0x6c/0x88
[<0000000329c2fc66>] cpuhp_invoke_callback+0x156/0x2f0
[<000000032aa062da>] _cpu_down.constprop.0+0x22a/0x5e0
[<0000000329c3243e>] cpu_device_down+0x4e/0x78
[<000000032a61dee0>] device_offline+0xc8/0x118
[<000000032a61e048>] online_store+0x60/0xe0
[<000000032a08b6b0>] kernfs_fop_write_iter+0x150/0x1e8
[<0000000329fab65c>] vfs_write+0x174/0x360
[<0000000329fab9fc>] ksys_write+0x74/0x100
[<000000032aa03a5a>] __do_syscall+0x1da/0x208
[<000000032aa177b2>] system_call+0x82/0xb0
INFO: lockdep is turned off.
FIX dma-kmalloc-64: Restoring kmalloc Redzone 0x0000000000400564-0x0000000000400567=0xcc
FIX dma-kmalloc-64: Object at 0x0000000000400540 not freed
Fixes: 2356f4cb19 ("[S390]: Rewrite of the IUCV base code, part 2")
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Link: https://lore.kernel.org/r/20230315131435.4113889-1-wintera@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8a2618e14f ]
Commit f96a3d7455 ("ipv4: Fix incorrect route flushing when source
address is deleted") started to take the table ID field in the FIB info
structure into account when determining if two structures are identical
or not. This field is initialized using the 'fc_table' field in the
route configuration structure, which is not set when adding a route via
IOCTL.
The above can result in user space being able to install two identical
routes that only differ in the table ID field of their associated FIB
info.
Fix by initializing the table ID field in the route configuration
structure in the IOCTL path.
Before the fix:
# ip route add default via 192.0.2.2
# route add default gw 192.0.2.2
# ip -4 r show default
# default via 192.0.2.2 dev dummy10
# default via 192.0.2.2 dev dummy10
After the fix:
# ip route add default via 192.0.2.2
# route add default gw 192.0.2.2
SIOCADDRT: File exists
# ip -4 r show default
default via 192.0.2.2 dev dummy10
Audited the code paths to ensure there are no other paths that do not
properly initialize the route configuration structure when installing a
route.
Fixes: 5a56a0b3a4 ("net: Don't delete routes in different VRFs")
Fixes: f96a3d7455 ("ipv4: Fix incorrect route flushing when source address is deleted")
Reported-by: gaoxingwang <gaoxingwang1@huawei.com>
Link: https://lore.kernel.org/netdev/20230314144159.2354729-1-gaoxingwang1@huawei.com/
Tested-by: gaoxingwang <gaoxingwang1@huawei.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20230315124009.4015212-1-idosch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6173a77b7e ]
An nvme target ->queue_response() operation implementation may free the
request passed as argument. Such implementation potentially could result
in a use after free of the request pointer when percpu_ref_put() is
called in nvmet_req_complete().
Avoid such problem by using a local variable to save the sq pointer
before calling __nvmet_req_complete(), thus avoiding dereferencing the
req pointer after that function call.
Fixes: a07b4970f4 ("nvmet: add a generic NVMe target")
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d8b2283189 ]
Packet length retrieved from skb data may be larger than
the actual socket buffer length (up to 9026 bytes). In such
case the cloned skb passed up the network stack will leak
kernel memory contents.
Fixes: d0cad87170 ("smsc75xx: SMSC LAN75xx USB gigabit ethernet adapter driver")
Signed-off-by: Szymon Heidrich <szymon.heidrich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5000fe6c27 ]
This bug influences both st_nci_i2c_remove and st_nci_spi_remove.
Take st_nci_i2c_remove as an example.
In st_nci_i2c_probe, it called ndlc_probe and bound &ndlc->sm_work
with llt_ndlc_sm_work.
When it calls ndlc_recv or timeout handler, it will finally call
schedule_work to start the work.
When we call st_nci_i2c_remove to remove the driver, there
may be a sequence as follows:
Fix it by finishing the work before cleanup in ndlc_remove
CPU0 CPU1
|llt_ndlc_sm_work
st_nci_i2c_remove |
ndlc_remove |
st_nci_remove |
nci_free_device|
kfree(ndev) |
//free ndlc->ndev |
|llt_ndlc_rcv_queue
|nci_recv_frame
|//use ndlc->ndev
Fixes: 35630df68d ("NFC: st21nfcb: Add driver for STMicroelectronics ST21NFCB NFC chip")
Signed-off-by: Zheng Wang <zyytlz.wz@163.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230312160837.2040857-1-zyytlz.wz@163.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1a9dc5610e ]
Previously we would divide total_left_rate by zero if num_vports
happened to be 1 because non_requested_count is calculated as
num_vports - req_count. Guard against this by validating num_vports at
the beginning and returning an error otherwise.
Found by Linux Verification Center (linuxtesting.org) with the SVACE
static analysis tool.
Fixes: bcd197c81f ("qed: Add vport WFQ configuration APIs")
Signed-off-by: Daniil Tatianin <d-tatianin@yandex-team.ru>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230309201556.191392-1-d-tatianin@yandex-team.ru
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 59a0b022aa ]
For l3s mode, skb->dev is set to ipvlan interface in ipvlan_nf_input():
skb->dev = addr->master->dev
but, skb->skb_iif remain unchanged, this will cause socket lookup failed
if a target socket is bound to a interface, like the following example:
ip link add ipvlan0 link eth0 type ipvlan mode l3s
ip addr add dev ipvlan0 192.168.124.111/24
ip link set ipvlan0 up
ping -c 1 -I ipvlan0 8.8.8.8
100% packet loss
This is because there is no match sk in __raw_v4_lookup() as sk->sk_bound_dev_if != dif(skb->skb_iif).
Fix this by make skb->skb_iif track skb->dev in ipvlan_nf_input().
Fixes: c675e06a98 ("ipvlan: decouple l3s mode dependencies from other modes")
Signed-off-by: Jianguo Wu <wujianguo@chinatelecom.cn>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Link: https://lore.kernel.org/r/29865b1f-6db7-c07a-de89-949d3721ea30@163.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 484b705979 ]
struct pn533_out_arg used as a temporary context for out_urb is not
initialized properly. Its uninitialized 'phy' field can be dereferenced in
error cases inside pn533_out_complete() callback function. It causes the
following failure:
general protection fault, probably for non-canonical address 0xdffffc0000000000: 0000 [#1] PREEMPT SMP KASAN
KASAN: null-ptr-deref in range [0x0000000000000000-0x0000000000000007]
CPU: 1 PID: 0 Comm: swapper/1 Not tainted 6.2.0-rc3-next-20230110-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 10/26/2022
RIP: 0010:pn533_out_complete.cold+0x15/0x44 drivers/nfc/pn533/usb.c:441
Call Trace:
<IRQ>
__usb_hcd_giveback_urb+0x2b6/0x5c0 drivers/usb/core/hcd.c:1671
usb_hcd_giveback_urb+0x384/0x430 drivers/usb/core/hcd.c:1754
dummy_timer+0x1203/0x32d0 drivers/usb/gadget/udc/dummy_hcd.c:1988
call_timer_fn+0x1da/0x800 kernel/time/timer.c:1700
expire_timers+0x234/0x330 kernel/time/timer.c:1751
__run_timers kernel/time/timer.c:2022 [inline]
__run_timers kernel/time/timer.c:1995 [inline]
run_timer_softirq+0x326/0x910 kernel/time/timer.c:2035
__do_softirq+0x1fb/0xaf6 kernel/softirq.c:571
invoke_softirq kernel/softirq.c:445 [inline]
__irq_exit_rcu+0x123/0x180 kernel/softirq.c:650
irq_exit_rcu+0x9/0x20 kernel/softirq.c:662
sysvec_apic_timer_interrupt+0x97/0xc0 arch/x86/kernel/apic/apic.c:1107
Initialize the field with the pn533_usb_phy currently used.
Found by Linux Verification Center (linuxtesting.org) with Syzkaller.
Fixes: 9dab880d67 ("nfc: pn533: Wait for out_urb's completion in pn533_usb_send_frame()")
Reported-by: syzbot+1e608ba4217c96d1952f@syzkaller.appspotmail.com
Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230309165050.207390-1-pchelkin@ispras.ru
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bced3f7db9 ]
tcp_rtx_synack() now could be called in process context as explained in
0a375c8224 ("tcp: tcp_rtx_synack() can be called from process
context").
tcp_rtx_synack() might call tcp_make_synack(), which will touch per-CPU
variables with preemption enabled. This causes the following BUG:
BUG: using __this_cpu_add() in preemptible [00000000] code: ThriftIO1/5464
caller is tcp_make_synack+0x841/0xac0
Call Trace:
<TASK>
dump_stack_lvl+0x10d/0x1a0
check_preemption_disabled+0x104/0x110
tcp_make_synack+0x841/0xac0
tcp_v6_send_synack+0x5c/0x450
tcp_rtx_synack+0xeb/0x1f0
inet_rtx_syn_ack+0x34/0x60
tcp_check_req+0x3af/0x9e0
tcp_rcv_state_process+0x59b/0x2030
tcp_v6_do_rcv+0x5f5/0x700
release_sock+0x3a/0xf0
tcp_sendmsg+0x33/0x40
____sys_sendmsg+0x2f2/0x490
__sys_sendmsg+0x184/0x230
do_syscall_64+0x3d/0x90
Avoid calling __TCP_INC_STATS() with will touch per-cpu variables. Use
TCP_INC_STATS() which is safe to be called from context switch.
Fixes: 8336886f78 ("tcp: TCP Fast Open Server - support TFO listeners")
Signed-off-by: Breno Leitao <leitao@debian.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20230308190745.780221-1-leitao@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 493924519b ]
`nft_redir_inet_type.maxattrs` was being set, presumably because of a
cut-and-paste error, to `NFTA_MASQ_MAX`, instead of `NFTA_REDIR_MAX`.
Fixes: 63ce3940f3 ("netfilter: nft_redir: add inet support")
Signed-off-by: Jeremy Sowden <jeremy@azazel.net>
Reviewed-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ff447886e6 ]
CONTROLLER_IN_GPU() is clearly intended to match only Intel devices, but
previously it checked only the PCI Device ID, not the Vendor ID, so it
could match devices from other vendors that happened to use the same Device
ID.
Update CONTROLLER_IN_GPU() so it matches only Intel devices.
Fixes: 535115b5ff ("ALSA: hda - Abort the probe without i915 binding for HSW/B")
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/20230307214054.886721-1-helgaas@kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d3c57724f1 ]
Port is allocated by sas_port_alloc_num() and rphy is allocated by either
sas_end_device_alloc() or sas_expander_alloc(), all of which may return
NULL. So we need to check the rphy to avoid possible NULL pointer access.
If sas_rphy_add() returned with failure, rphy is set to NULL. We would
access the rphy in the following lines which would also result NULL pointer
access.
Fixes: 78316e9dfc ("scsi: mpt3sas: Fix possible resource leaks in mpt3sas_transport_port_add()")
Signed-off-by: Wenchao Hao <haowenchao2@huawei.com>
Link: https://lore.kernel.org/r/20230225100135.2109330-1-haowenchao2@huawei.com
Acked-by: Sathya Prakash Veerichetty <sathya.prakash@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d0dc411199 ]
When send SMB_COM_NT_CANCEL and RFC1002_SESSION_REQUEST, the
in_send statistic was lost.
Let's move the in_send statistic to the send function to avoid
this scenario.
Fixes: 7ee1af765d ("[CIFS]")
Signed-off-by: Zhang Xiaoxu <zhangxiaoxu5@huawei.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c276a706ea ]
xfrm state selectors are matched against the inner-most flow
which can be of any address family. Therefore middle states
in nested configurations need to carry a wildcard selector in
order to work at all.
However, this is currently forbidden for transport-mode states.
Fix this by removing the unnecessary check.
Fixes: 13996378e6 ("[IPSEC]: Rename mode to outer_mode and add inner_mode")
Reported-by: David George <David.George@sophos.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit ffec85d53d upstream.
When writing a page from an encrypted file that is using
filesystem-layer encryption (not inline encryption), ext4 encrypts the
pagecache page into a bounce page, then writes the bounce page.
It also passes the bounce page to wbc_account_cgroup_owner(). That's
incorrect, because the bounce page is a newly allocated temporary page
that doesn't have the memory cgroup of the original pagecache page.
This makes wbc_account_cgroup_owner() not account the I/O to the owner
of the pagecache page as it should.
Fix this by always passing the pagecache page to
wbc_account_cgroup_owner().
Fixes: 001e4a8775 ("ext4: implement cgroup writeback support")
Cc: stable@vger.kernel.org
Reported-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Acked-by: Tejun Heo <tj@kernel.org>
Link: https://lore.kernel.org/r/20230203005503.141557-1-ebiggers@kernel.org
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b99ddbe833 upstream.
With CONFIG_VIRTIO_UML=y, GNU ld < 2.36 fails to link UML vmlinux
(w/wo CONFIG_LD_SCRIPT_STATIC).
`.exit.text' referenced in section `.uml.exitcall.exit' of arch/um/drivers/virtio_uml.o: defined in discarded section `.exit.text' of arch/um/drivers/virtio_uml.o
collect2: error: ld returned 1 exit status
This fix is similar to the following commits:
- 4b9880dbf3 ("powerpc/vmlinux.lds: Define RUNTIME_DISCARD_EXIT")
- a494398bde ("s390: define RUNTIME_DISCARD_EXIT to fix link error
with GNU ld < 2.36")
- c1c551bebf ("sh: define RUNTIME_DISCARD_EXIT")
Fixes: 99cb0d917f ("arch: fix broken BuildID for arm64 and riscv")
Reported-by: SeongJae Park <sj@kernel.org>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Tested-by: SeongJae Park <sj@kernel.org>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c1c551bebf upstream.
sh vmlinux fails to link with GNU ld < 2.40 (likely < 2.36) since
commit 99cb0d917f ("arch: fix broken BuildID for arm64 and riscv").
This is similar to fixes for powerpc and s390:
commit 4b9880dbf3 ("powerpc/vmlinux.lds: Define RUNTIME_DISCARD_EXIT").
commit a494398bde ("s390: define RUNTIME_DISCARD_EXIT to fix link error
with GNU ld < 2.36").
$ sh4-linux-gnu-ld --version | head -n1
GNU ld (GNU Binutils for Debian) 2.35.2
$ make ARCH=sh CROSS_COMPILE=sh4-linux-gnu- microdev_defconfig
$ make ARCH=sh CROSS_COMPILE=sh4-linux-gnu-
`.exit.text' referenced in section `__bug_table' of crypto/algboss.o:
defined in discarded section `.exit.text' of crypto/algboss.o
`.exit.text' referenced in section `__bug_table' of
drivers/char/hw_random/core.o: defined in discarded section
`.exit.text' of drivers/char/hw_random/core.o
make[2]: *** [scripts/Makefile.vmlinux:34: vmlinux] Error 1
make[1]: *** [Makefile:1252: vmlinux] Error 2
arch/sh/kernel/vmlinux.lds.S keeps EXIT_TEXT:
/*
* .exit.text is discarded at runtime, not link time, to deal with
* references from __bug_table
*/
.exit.text : AT(ADDR(.exit.text)) { EXIT_TEXT }
However, EXIT_TEXT is thrown away by
DISCARD(include/asm-generic/vmlinux.lds.h) because
sh does not define RUNTIME_DISCARD_EXIT.
GNU ld 2.40 does not have this issue and builds fine.
This corresponds with Masahiro's comments in a494398bde:
"Nathan [Chancellor] also found that binutils
commit 21401fc7bf67 ("Duplicate output sections in scripts") cured this
issue, so we cannot reproduce it with binutils 2.36+, but it is better
to not rely on it."
Link: https://lkml.kernel.org/r/9166a8abdc0f979e50377e61780a4bba1dfa2f52.1674518464.git.tom.saeger@oracle.com
Fixes: 99cb0d917f ("arch: fix broken BuildID for arm64 and riscv")
Link: https://lore.kernel.org/all/Y7Jal56f6UBh1abE@dev-arch.thelio-3990X/
Link: https://lore.kernel.org/all/20230123194218.47ssfzhrpnv3xfez@oracle.com/
Signed-off-by: Tom Saeger <tom.saeger@oracle.com>
Tested-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Cc: Ard Biesheuvel <ardb@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Dennis Gilmore <dennis@ausil.us>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Masahiro Yamada <masahiroy@kernel.org>
Cc: Naresh Kamboju <naresh.kamboju@linaro.org>
Cc: Nathan Chancellor <nathan@kernel.org>
Cc: Palmer Dabbelt <palmer@rivosinc.com>
Cc: Rich Felker <dalias@libc.org>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Tom Saeger <tom.saeger@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a494398bde upstream.
Nathan Chancellor reports that the s390 vmlinux fails to link with
GNU ld < 2.36 since commit 99cb0d917f ("arch: fix broken BuildID
for arm64 and riscv").
It happens for defconfig, or more specifically for CONFIG_EXPOLINE=y.
$ s390x-linux-gnu-ld --version | head -n1
GNU ld (GNU Binutils for Debian) 2.35.2
$ make -s ARCH=s390 CROSS_COMPILE=s390x-linux-gnu- allnoconfig
$ ./scripts/config -e CONFIG_EXPOLINE
$ make -s ARCH=s390 CROSS_COMPILE=s390x-linux-gnu- olddefconfig
$ make -s ARCH=s390 CROSS_COMPILE=s390x-linux-gnu-
`.exit.text' referenced in section `.s390_return_reg' of drivers/base/dd.o: defined in discarded section `.exit.text' of drivers/base/dd.o
make[1]: *** [scripts/Makefile.vmlinux:34: vmlinux] Error 1
make: *** [Makefile:1252: vmlinux] Error 2
arch/s390/kernel/vmlinux.lds.S wants to keep EXIT_TEXT:
.exit.text : {
EXIT_TEXT
}
But, at the same time, EXIT_TEXT is thrown away by DISCARD because
s390 does not define RUNTIME_DISCARD_EXIT.
I still do not understand why the latter wins after 99cb0d917f,
but defining RUNTIME_DISCARD_EXIT seems correct because the comment
line in arch/s390/kernel/vmlinux.lds.S says:
/*
* .exit.text is discarded at runtime, not link time,
* to deal with references from __bug_table
*/
Nathan also found that binutils commit 21401fc7bf67 ("Duplicate output
sections in scripts") cured this issue, so we cannot reproduce it with
binutils 2.36+, but it is better to not rely on it.
Fixes: 99cb0d917f ("arch: fix broken BuildID for arm64 and riscv")
Link: https://lore.kernel.org/all/Y7Jal56f6UBh1abE@dev-arch.thelio-3990X/
Reported-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Link: https://lore.kernel.org/r/20230105031306.1455409-1-masahiroy@kernel.org
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Tom Saeger <tom.saeger@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 07b050f929 upstream.
Relocatable kernels must not discard relocations, they need to be
processed at runtime. As such they are included for CONFIG_RELOCATABLE
builds in the powerpc linker script (line 340).
However they are also unconditionally discarded later in the
script (line 414). Previously that worked because the earlier inclusion
superseded the discard.
However commit 99cb0d917f ("arch: fix broken BuildID for arm64 and
riscv") introduced an earlier use of DISCARD as part of the RO_DATA
macro (line 137). With binutils < 2.36 that causes the DISCARD
directives later in the script to be applied earlier, causing .rela* to
actually be discarded at link time, leading to build warnings and a
kernel that doesn't boot:
ld: warning: discarding dynamic section .rela.init.rodata
Fix it by conditionally discarding .rela* only when CONFIG_RELOCATABLE
is disabled.
Fixes: 99cb0d917f ("arch: fix broken BuildID for arm64 and riscv")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20230105132349.384666-2-mpe@ellerman.id.au
Signed-off-by: Tom Saeger <tom.saeger@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4b9880dbf3 upstream.
The powerpc linker script explicitly includes .exit.text, because
otherwise the link fails due to references from __bug_table and
__ex_table. The code is freed (discarded) at runtime along with
.init.text and data.
That has worked in the past despite powerpc not defining
RUNTIME_DISCARD_EXIT because DISCARDS appears late in the powerpc linker
script (line 410), and the explicit inclusion of .exit.text
earlier (line 280) supersedes the discard.
However commit 99cb0d917f ("arch: fix broken BuildID for arm64 and
riscv") introduced an earlier use of DISCARD as part of the RO_DATA
macro (line 136). With binutils < 2.36 that causes the DISCARD
directives later in the script to be applied earlier [1], causing
.exit.text to actually be discarded at link time, leading to build
errors:
'.exit.text' referenced in section '__bug_table' of crypto/algboss.o: defined in
discarded section '.exit.text' of crypto/algboss.o
'.exit.text' referenced in section '__ex_table' of drivers/nvdimm/core.o: defined in
discarded section '.exit.text' of drivers/nvdimm/core.o
Fix it by defining RUNTIME_DISCARD_EXIT, which causes the generic
DISCARDS macro to not include .exit.text at all.
1: https://lore.kernel.org/lkml/87fscp2v7k.fsf@igel.home/
Fixes: 99cb0d917f ("arch: fix broken BuildID for arm64 and riscv")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20230105132349.384666-1-mpe@ellerman.id.au
Signed-off-by: Tom Saeger <tom.saeger@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 99cb0d917f upstream.
Dennis Gilmore reports that the BuildID is missing in the arm64 vmlinux
since commit 994b7ac169 ("arm64: remove special treatment for the
link order of head.o").
The issue is that the type of .notes section, which contains the BuildID,
changed from NOTES to PROGBITS.
Ard Biesheuvel figured out that whichever object gets linked first gets
to decide the type of a section. The PROGBITS type is the result of the
compiler emitting .note.GNU-stack as PROGBITS rather than NOTE.
While Ard provided a fix for arm64, I want to fix this globally because
the same issue is happening on riscv since commit 2348e6bf44 ("riscv:
remove special treatment for the link order of head.o"). This problem
will happen in general for other architectures if they start to drop
unneeded entries from scripts/head-object-list.txt.
Discard .note.GNU-stack in include/asm-generic/vmlinux.lds.h.
Link: https://lore.kernel.org/lkml/CAABkxwuQoz1CTbyb57n0ZX65eSYiTonFCU8-LCQc=74D=xE=rA@mail.gmail.com/
Fixes: 994b7ac169 ("arm64: remove special treatment for the link order of head.o")
Fixes: 2348e6bf44 ("riscv: remove special treatment for the link order of head.o")
Reported-by: Dennis Gilmore <dennis@ausil.us>
Suggested-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Acked-by: Palmer Dabbelt <palmer@rivosinc.com>
[Tom: stable backport 5.15.y, 5.10.y, 5.4.y]
Though the above "Fixes:" commits are not in this kernel, the conditions
which lead to a missing Build ID in arm64 vmlinux are similar.
Evidence points to these conditions:
1. ld version > 2.36 (exact binutils commit documented in a494398bde)
2. first object which gets linked (head.o) has a PROGBITS .note.GNU-stack segment
These conditions can be observed when:
- 5.15.60+ OR 5.10.136+ OR 5.4.210+
- AND ld version > 2.36
- AND arch=arm64
- AND CONFIG_MODVERSIONS=y
There are notable differences in the vmlinux elf files produced
before(bad) and after(good) applying this series.
Good: p_type:PT_NOTE segment exists.
Bad: p_type:PT_NOTE segment is missing.
Good: sh_name_str:.notes section has sh_type:SHT_NOTE
Bad: sh_name_str:.notes section has sh_type:SHT_PROGBITS
`readelf -n` (as of v2.40) searches for Build Id
by processing only the very first note in sh_type:SHT_NOTE sections.
This was previously bisected to the stable backport of 0d362be5b1.
Follow-up experiments were discussed here: https://lore.kernel.org/all/20221221235413.xaisboqmr7dkqwn6@oracle.com/
which strongly hints at condition 2.
Signed-off-by: Tom Saeger <tom.saeger@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 84d5f77fc2 upstream.
In the x86 kernel, .exit.text and .exit.data sections are discarded at
runtime, not by the linker. Add RUNTIME_DISCARD_EXIT to generic DISCARDS
and define it in the x86 kernel linker script to keep them.
The sections are added before the DISCARD directive so document here
only the situation explicitly as this change doesn't have any effect on
the generated kernel. Also, other architectures like ARM64 will use it
too so generalize the approach with the RUNTIME_DISCARD_EXIT define.
[ bp: Massage and extend commit message. ]
Signed-off-by: H.J. Lu <hjl.tools@gmail.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Kees Cook <keescook@chromium.org>
Link: https://lkml.kernel.org/r/20200326193021.255002-1-hjl.tools@gmail.com
Signed-off-by: Tom Saeger <tom.saeger@oracle.com>
commit db05ddf7f3 upstream.
You will get two decrements when the messages on a panic are sent, not
one, since commit 2033f68589 ("ipmi: Free receive messages when in an
oops") was added, but the watchdog code had a bug where it didn't set
the value properly.
Reported-by: Anton Lundin <glance@acc.umu.se>
Cc: <Stable@vger.kernel.org> # v5.4+
Fixes: 2033f68589 ("ipmi: Free receive messages when in an oops")
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit afa4805799 ]
Gain control is badly documented in publicly available (including
leaked) documentation.
There is an AGC pre-gain in register 0x3a13, expressed as a 6-bit value
(plus an enable bit in bit 6). The driver hardcodes it to 0x43, which
one application note states is equal to x1.047. The documentation also
states that 0x40 is equel to x1.000. The pre-gain thus seems to be
expressed as in 1/64 increments, and thus ranges from x1.00 to x1.984.
What the pre-gain does is however unspecified.
There is then an AGC gain limit, in registers 0x3a18 and 0x3a19,
expressed as a 10-bit "real gain format" value. One application note
sets it to 0x00f8 and states it is equal to x15.5, so it appears to be
expressed in 1/16 increments, up to x63.9375.
The manual gain is stored in registers 0x350a and 0x350b, also as a
10-bit "real gain format" value. It is documented in the application
note as a Q6.4 values, up to x63.9375.
One version of the datasheet indicates that the sensor supports a
digital gain:
The OV5640 supports 1/2/4 digital gain. Normally, the gain is
controlled automatically by the automatic gain control (AGC) block.
It isn't clear how that would be controlled manually.
There appears to be no indication regarding whether the gain controlled
through registers 0x350a and 0x350b is an analogue gain only or also
includes digital gain. The words "real gain" don't necessarily mean
"combined analogue and digital gains". Some OmniVision sensors (such as
the OV8858) are documented as supoprting different formats for the gain
values, selectable through a register bit, and they are called "real
gain format" and "sensor gain format". For that sensor, we have (one of)
the gain registers documented as
0x3503[2]=0, gain[7:0] is real gain format, where low 4 bits are
fraction bits, for example, 0x10 is 1x gain, 0x28 is 2.5x gain
If 0x3503[2]=1, gain[7:0] is sensor gain format, gain[7:4] is coarse
gain, 00000: 1x, 00001: 2x, 00011: 4x, 00111: 8x, gain[7] is 1,
gain[3:0] is fine gain. For example, 0x10 is 1x gain, 0x30 is 2x gain,
0x70 is 4x gain
(The second part of the text makes little sense)
"Real gain" may thus refer to the combination of the coarse and fine
analogue gains as a single value.
The OV5640 0x350a and 0x350b registers thus appear to control analogue
gain. The driver incorrectly uses V4L2_CID_GAIN as V4L2 has a specific
control for analogue gain, V4L2_CID_ANALOGUE_GAIN. Use it.
If registers 0x350a and 0x350b are later found to control digital gain
as well, the driver could then restrict the range of the analogue gain
control value to lower than x64 and add a separate digital gain control.
Signed-off-by: Paul Elder <paul.elder@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Reviewed-by: Jai Luthra <j-luthra@ti.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
