commit 52fbe9cde7 upstream.
The ring buffer resizing and resetting relies on a schedule RCU
action. The buffers are disabled, a synchronize_sched() is called
and then the resize or reset takes place.
But this only works if the disabling of the buffers are within the
preempt disabled section, otherwise a window exists that the buffers
can be written to while a reset or resize takes place.
Reported-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com>
LKML-Reference: <4B949E43.2010906@cn.fujitsu.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit a951ae2176 upstream.
The beacon sent gating doesn't seem to work with any combination
of flags. Thus, buffered frames tend to stay buffered forever,
using up tx descriptors.
Instead, use the DBA gating and hold transmission of the buffered
frames until 80% of the beacon interval has elapsed using the ready
time. This fixes the following error in AP mode:
ath5k phy0: no further txbuf available, dropping packet
Add a comment to acknowledge that this isn't the best solution.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 86415d43ef upstream.
I/Q calibration was completely broken, resulting in a high number of CRC errors
on received packets. before i could see around 10% to 20% CRC errors, with this
patch they are between 0% and 3%.
1.) the removal of the mask in commit "ath5k: Fix I/Q calibration
(f1cf2dbd0f)" resulted in no mask beeing used
when writing the I/Q values into the register. additional errors in the
calculation of the values (see 2.) resulted too high numbers, exceeding the
masks, so wrong values like 0xfffffffe were written. to be safe we should
always use the bitmask when writing parts of a register.
2.) using a (s32) cast for q_coff is a wrong conversion to signed, since we
convert to a signed value later by substracting 128. this resulted in too low
numbers for Q many times, which were limited to -16 by the boundary check later
on.
3.) checked everything against the HAL sources and took over comments and minor
optimizations from there.
4.) we can't use ENABLE_BITS when we want to write a number (the number can
contain zeros). also always write the correction values first and set ENABLE
bit last, like the HAL does.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit c074c39d62 upstream.
Experience has shown that the block buffer can only be used for SMBus
(not I2C) block transactions, even though the datasheet doesn't
mention this limitation.
Reported-by: Felix Rubinstein <felixru@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Oleg Ryjkov <oryjkov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 8e4b980c28 upstream.
Be less verbose in the absence of real errors. We don't have to report
failed probes to the users, it's only confusing them.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Andrey Gusev <ronne@list.ru>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 31968ecf58 upstream.
ALDI/MEDION netbook E1222 needs to be in the reset quirk list for
its touchpad's proper function.
Reported-by: Michael Fischer <mifi@gmx.de>
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit ad6759fbf3 upstream.
Aaro Koskinen reported an issue in kernel.org bugzilla #15366, where
on non-GENERIC_TIME systems, accessing
/sys/devices/system/clocksource/clocksource0/current_clocksource
results in an oops.
It seems the timekeeper/clocksource rework missed initializing the
curr_clocksource value in the !GENERIC_TIME case.
Thanks to Aaro for reporting and diagnosing the issue as well as
testing the fix!
Reported-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
LKML-Reference: <1267475683.4216.61.camel@localhost.localdomain>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 5311114d48 upstream.
Since alc_auto_create_input_ctls() doesn't set the elements for the
secondary ADCs, "Input Source" elemtns for these also get empty, resulting
in buggy outputs of alsactl like:
control.14 {
comment.access 'read write'
comment.type ENUMERATED
comment.count 1
iface MIXER
name 'Input Source'
index 1
value 0
}
This patch fixes alc_mux_enum_*() (and others) to fall back to the
first entry if the secondary input mux is empty.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit ecd216260f upstream.
without the following patch audio ssttuutteerrs on
ASUS M2N32-SLI PREMIUM ACPI BIOS Revision 1304
the sound device is:
00:0e.1 Audio device: nVidia Corporation MCP55 High Definition Audio (rev a2)
worked with 2.6.32
Signed-off-by: Ralf Gerbig <rge@quengel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit fe234f0e5c upstream.
Commit 09943a1819
Author: Matt Carlson <mcarlson@broadcom.com>
Date: Fri Aug 28 14:01:57 2009 +0000
tg3: Convert ISR parameter to tnapi
forgot to update tg3_poll_controller(), leading to intermittent crashes with
netpoll.
Fix this.
Signed-off-by: Louis Rilling <louis.rilling@kerlabs.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 4fa0043731 upstream.
Handling HT configuration changes involved setting the channel
with the new HT parameters and then issuing a rate_update()
notification to the driver.
This behavior changed after the off-channel changes. Now, the channel
is not updated with the new HT params in enable_ht() - instead, it
is now done when the scan work terminates. This results in the driver
depending on stale information, defaulting to non-HT mode always.
Fix this by passing the new channel type to the driver.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 98e12b5a6e upstream.
Commit 2552fc2 changed the way the decompressor decides if it is safe
to decompress the kernel directly to its final location. Unfortunately,
it took the top of the compressed data as being the stack pointer,
which it is for ROM=n cases. However, for ROM=y, the stack pointer
is not relevant, and results in the wrong answer.
Fix this by explicitly storing the end of the biggybacked data in the
decompressor, and use that to calculate the compressed image size.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 5ceaa2f39b upstream.
The ARM kernel decompressor wants to be able to relocate r/w data
independently from the rest of the image, and we do this by ensuring that
r/w data has global visibility. Define STATIC_RW_DATA to be empty to
achieve this.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Alain Knaff <alain@knaff.lu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 9b3a6549b2 upstream.
The few lines below the kfree of hdr_buf may go to the label err_free
which will also free hdr_buf. The most straightforward solution seems to
be to just move the kfree of hdr_buf after these gotos.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@r@
identifier E;
expression E1;
iterator I;
statement S;
@@
*kfree(E);
... when != E = E1
when != I(E,...) S
when != &E
*kfree(E);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 1431559200 upstream.
Distros generally (I looked at Debian, RHEL5 and SLES11) seem to
enable CONFIG_HIGHPTE for any x86 configuration which has highmem
enabled. This means that the overhead applies even to machines which
have a fairly modest amount of high memory and which therefore do not
really benefit from allocating PTEs in high memory but still pay the
price of the additional mapping operations.
Running kernbench on a 4G box I found that with CONFIG_HIGHPTE=y but
no actual highptes being allocated there was a reduction in system
time used from 59.737s to 55.9s.
With CONFIG_HIGHPTE=y and highmem PTEs being allocated:
Average Optimal load -j 4 Run (std deviation):
Elapsed Time 175.396 (0.238914)
User Time 515.983 (5.85019)
System Time 59.737 (1.26727)
Percent CPU 263.8 (71.6796)
Context Switches 39989.7 (4672.64)
Sleeps 42617.7 (246.307)
With CONFIG_HIGHPTE=y but with no highmem PTEs being allocated:
Average Optimal load -j 4 Run (std deviation):
Elapsed Time 174.278 (0.831968)
User Time 515.659 (6.07012)
System Time 55.9 (1.07799)
Percent CPU 263.8 (71.266)
Context Switches 39929.6 (4485.13)
Sleeps 42583.7 (373.039)
This patch allows the user to control the allocation of PTEs in
highmem from the command line ("userpte=nohigh") but retains the
status-quo as the default.
It is possible that some simple heuristic could be developed which
allows auto-tuning of this option however I don't have a sufficiently
large machine available to me to perform any particularly meaningful
experiments. We could probably handwave up an argument for a threshold
at 16G of total RAM.
Assuming 768M of lowmem we have 196608 potential lowmem PTE
pages. Each page can map 2M of RAM in a PAE-enabled configuration,
meaning a maximum of 384G of RAM could potentially be mapped using
lowmem PTEs.
Even allowing generous factor of 10 to account for other required
lowmem allocations, generous slop to account for page sharing (which
reduces the total amount of RAM mappable by a given number of PT
pages) and other innacuracies in the estimations it would seem that
even a 32G machine would not have a particularly pressing need for
highmem PTEs. I think 32G could be considered to be at the upper bound
of what might be sensible on a 32 bit machine (although I think in
practice 64G is still supported).
It's seems questionable if HIGHPTE is even a win for any amount of RAM
you would sensibly run a 32 bit kernel on rather than going 64 bit.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
LKML-Reference: <1266403090-20162-1-git-send-email-ian.campbell@citrix.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 83ab0aa0d5 upstream.
setscheduler() saves task->sched_class outside of the rq->lock held
region for a check after the setscheduler changes have become
effective. That might result in checking a stale value.
rtmutex_setprio() has the same problem, though it is protected by
p->pi_lock against setscheduler(), but for correctness sake (and to
avoid bad examples) it needs to be fixed as well.
Retrieve task->sched_class inside of the rq->lock held region.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 9000f05c6d upstream.
Fix a SMT scheduler performance regression that is leading to a scenario
where SMT threads in one core are completely idle while both the SMT threads
in another core (on the same socket) are busy.
This is caused by this commit (with the problematic code highlighted)
commit bdb94aa5db
Author: Peter Zijlstra <a.p.zijlstra@chello.nl>
Date: Tue Sep 1 10:34:38 2009 +0200
sched: Try to deal with low capacity
@@ -4203,15 +4223,18 @@ find_busiest_queue()
...
for_each_cpu(i, sched_group_cpus(group)) {
+ unsigned long power = power_of(i);
...
- wl = weighted_cpuload(i);
+ wl = weighted_cpuload(i) * SCHED_LOAD_SCALE;
+ wl /= power;
- if (rq->nr_running == 1 && wl > imbalance)
+ if (capacity && rq->nr_running == 1 && wl > imbalance)
continue;
On a SMT system, power of the HT logical cpu will be 589 and
the scheduler load imbalance (for scenarios like the one mentioned above)
can be approximately 1024 (SCHED_LOAD_SCALE). The above change of scaling
the weighted load with the power will result in "wl > imbalance" and
ultimately resulting in find_busiest_queue() return NULL, causing
load_balance() to think that the load is well balanced. But infact
one of the tasks can be moved to the idle core for optimal performance.
We don't need to use the weighted load (wl) scaled by the cpu power to
compare with imabalance. In that condition, we already know there is only a
single task "rq->nr_running == 1" and the comparison between imbalance,
wl is to make sure that we select the correct priority thread which matches
imbalance. So we really need to compare the imabalnce with the original
weighted load of the cpu and not the scaled load.
But in other conditions where we want the most hammered(busiest) cpu, we can
use scaled load to ensure that we consider the cpu power in addition to the
actual load on that cpu, so that we can move the load away from the
guy that is getting most hammered with respect to the actual capacity,
as compared with the rest of the cpu's in that busiest group.
Fix it.
Reported-by: Ma Ling <ling.ma@intel.com>
Initial-Analysis-by: Zhang, Yanmin <yanmin_zhang@linux.intel.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <1266023662.2808.118.camel@sbs-t61.sc.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 28f5318167 upstream.
Fix for sched_mc_powersavigs for pre-Nehalem platforms.
Child sched domain should clear SD_PREFER_SIBLING if parent will have
SD_POWERSAVINGS_BALANCE because they are contradicting.
Sets the flags correctly based on sched_mc_power_savings.
Signed-off-by: Vaidyanathan Srinivasan <svaidy@linux.vnet.ibm.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <20100208100555.GD2931@dirshya.in.ibm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit e92805ac12 upstream.
Add CPL checking in case emulator is tricked into emulating
privilege instruction from userspace.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 8b9f44140b upstream.
Inject #UD if guest attempts to do so. This is in accordance to Intel
SDM.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 2db2c2eb62 upstream.
Use groups mechanism to decode 0F BA instructions.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 59708670b6 upstream.
We don't support these instructions, but guest can execute them even if the
feature('monitor') haven't been exposed in CPUID. So we would trap and inject
a #UD if guest try this way.
Signed-off-by: Sheng Yang <sheng@linux.intel.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 0f3649a9e3 upstream.
Only issue a uevent on a resume if the state of the device changed,
i.e. if it was suspended and/or its table was replaced.
Signed-off-by: Dave Wysochanski <dwysocha@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit a97f925a32 upstream.
Free the dm_io structure before calling bio_endio() instead of after it,
to ensure that the io_pool containing it is not referenced after it is
freed.
This partially fixes a problem described here
https://www.redhat.com/archives/dm-devel/2010-February/msg00109.html
thread 1:
bio_endio(bio, io_error);
/* scheduling happens */
thread 2:
close the device
remove the device
thread 1:
free_io(md, io);
Thread 2, when removing the device, sees non-empty md->io_pool (because the
io hasn't been freed by thread 1 yet) and may crash with BUG in mempool_free.
Thread 1 may also crash, when freeing into a nonexisting mempool.
To fix this we must make sure that bio_endio() is the last call and
the md structure is not accessed afterwards.
There is another bio_endio in process_barrier, but it is called from the thread
and the thread is destroyed prior to freeing the mempools, so this call is
not affected by the bug.
A similar bug exists with module unloads - the module may be unloaded
immediately after bio_endio - but that is more difficult to fix.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit ebed9203b6 upstream.
sunrpc_cache_update() will always call detail->update() from inside the
detail->hash_lock, so it cannot allocate memory.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 3c840c18bc upstream.
If MAINTAINERS section entries are misformatted, it was possible to have
an infinite loop.
Correct the defect by always moving the index to the end of section + 1
Also, exit check for exclude as soon as possible.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit c212808a1b upstream.
If no platform_data was givin to the device it's going to use it's default
platform data struct which has all fields initialized to zero. As a
result the driver is going to try to request gpio0 both as write protect
and card detect pin. Which of course will fail and makes the driver
unusable
Previously to the introduction of no_wprotect and no_detect the behavior
was to assume that if no platform data was given there is no write protect
or card detect pin. This patch restores that behavior.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 9fcfe0c83c upstream.
This can, for instance, happen if the user specifies a link local IPv6
address.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit ab1b18f70a upstream.
The 'struct svc_deferred_req's on the xpt_deferred queue do not
own a reference to the owning xprt. This is seen in svc_revisit
which is where things are added to this queue. dr->xprt is set to
NULL and the reference to the xprt it put.
So when this list is cleaned up in svc_delete_xprt, we mustn't
put the reference.
Also, replace the 'for' with a 'while' which is arguably
simpler and more likely to compile efficiently.
Cc: Tom Tucker <tom@opengridcomputing.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 46216e4fbe upstream.
Enable the SD-Card interface on multiple Option 3G sticks.
The unusual_devs.h entry is necessary because the device descriptor is
vendor-specific. That prevents usb-storage from binding to it as an interface
driver.
Signed-off-by: Jan Dumon <j.dumon@option.com>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 46b72d78cb upstream.
This is a patch to ftdi_sio_ids.h and ftdi_sio.c that adds
identifiers for CONTEC USB serial converter. I tested it
with the device COM-1(USB)H
Signed-off-by: Daniel Sangorrin <daniel.sangorrin@gmail.com>
Cc: Andreas Mohr <andi@lisas.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 8e7e61dfbf upstream.
init_completion() hasn't been called yet and the thread isn't created
if we end up here, so don't call complete() on thread_notifier.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Acked-by: Michal Nazarewicz <m.nazarewicz@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit f7410ced7f upstream.
USB: Move hcd free_dev call into usb_disconnect
I found a way to oops the kernel:
1. Open a USB device through devio.
2. Remove the hcd module in the host kernel.
3. Close the devio file descriptor.
The problem is that closing the file descriptor does usb_release_dev
as it is the last reference. usb_release_dev then tries to invoke
the hcd free_dev function (or rather dereferencing the hcd driver
struct). This causes an oops as the hcd driver has already been
unloaded so the struct is gone.
This patch tries to fix this by bringing the free_dev call earlier
and into usb_disconnect. I have verified that repeating the
above steps no longer crashes with this patch applied.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit cceffe9348 upstream.
This patch (as1332) removes an unneeded and annoying debugging message
announcing all USB uevent constructions.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit d23356da71 upstream.
When hardware is removed on a Stratus, the system may crash like this:
ACPI: PCI interrupt for device 0000:7c:00.1 disabled
Trying to free nonexistent resource <00000000a8000000-00000000afffffff>
Trying to free nonexistent resource <00000000a4800000-00000000a480ffff>
uhci_hcd 0000:7e:1d.0: remove, state 1
usb usb2: USB disconnect, address 1
usb 2-1: USB disconnect, address 2
Unable to handle kernel paging request at 0000000000100100 RIP:
[<ffffffff88021950>] :uhci_hcd:uhci_scan_schedule+0xa2/0x89c
#4 [ffff81011de17e50] uhci_scan_schedule at ffffffff88021918
#5 [ffff81011de17ed0] uhci_irq at ffffffff88023cb8
#6 [ffff81011de17f10] usb_hcd_irq at ffffffff801f1c1f
#7 [ffff81011de17f20] handle_IRQ_event at ffffffff8001123b
#8 [ffff81011de17f50] __do_IRQ at ffffffff800ba749
This occurs because an interrupt scans uhci->skelqh, which is
being freed. We do the right thing: disable the interrupts in the
device, and do not do any processing if the interrupt is shared
with other source, but it's possible that another CPU gets
delayed somewhere (e.g. loops) until we started freeing.
The agreed-upon solution is to wait for interrupts to play out
before proceeding. No other bareers are neceesary.
A backport of this patch was tested on a 2.6.18 based kernel.
Testing of 2.6.32-based kernels is under way, but it takes us
forever (months) to turn this around. So I think it's a good
patch and we should keep it.
Tracked in RH bz#516851
Signed-Off-By: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit cd78069492 upstream.
This patch (as1346) changes the idProduct value for USB-3.0 root hubs
from 0x0002 (which we already use for USB-2.0 root hubs) to 0x0003.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 05197921ff upstream.
According "5.3.6 Capability Parameters (HCCPARAMS)" of xHCI rev0.96 spec,
value of xECP register indicates a relative offset, in 32-bit words,
from Base to the beginning of the first extended capability.
The wrong calculation will cause BIOS handoff fail (not handoff from BIOS)
in some platform with BIOS USB legacy sup support.
Signed-off-by: Edward Shao <laface.tw@gmail.com>
Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 18dce6ba5c upstream.
Thomas Renninger <trenn@suse.de> reported on IBM x3330
booting a latest kernel on this machine results in:
PCI: PCI BIOS revision 2.10 entry at 0xfd61c, last bus=1
PCI: Using configuration type 1 for base access bio: create slab <bio-0> at 0
ACPI: SCI (IRQ30) allocation failed
ACPI Exception: AE_NOT_ACQUIRED, Unable to install System Control Interrupt handler (20090903/evevent-161)
ACPI: Unable to start the ACPI Interpreter
Later all kind of devices fail...
and bisect it down to this commit:
commit b9c61b7007
x86/pci: update pirq_enable_irq() to setup io apic routing
it turns out we need to set irq routing for the sci on ioapic1 early.
-v2: make it work without sparseirq too.
-v3: fix checkpatch.pl warning, and cc to stable
Reported-by: Thomas Renninger <trenn@suse.de>
Bisected-by: Thomas Renninger <trenn@suse.de>
Tested-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <1265793639-15071-2-git-send-email-yinghai@kernel.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit ced5b697a7 upstream.
Keep chip_data in create_irq_nr and destroy_irq.
When two drivers are setting up MSI-X at the same time via
pci_enable_msix() there is a race. See this dmesg excerpt:
[ 85.170610] ixgbe 0000:02:00.1: irq 97 for MSI/MSI-X
[ 85.170611] alloc irq_desc for 99 on node -1
[ 85.170613] igb 0000:08:00.1: irq 98 for MSI/MSI-X
[ 85.170614] alloc kstat_irqs on node -1
[ 85.170616] alloc irq_2_iommu on node -1
[ 85.170617] alloc irq_desc for 100 on node -1
[ 85.170619] alloc kstat_irqs on node -1
[ 85.170621] alloc irq_2_iommu on node -1
[ 85.170625] ixgbe 0000:02:00.1: irq 99 for MSI/MSI-X
[ 85.170626] alloc irq_desc for 101 on node -1
[ 85.170628] igb 0000:08:00.1: irq 100 for MSI/MSI-X
[ 85.170630] alloc kstat_irqs on node -1
[ 85.170631] alloc irq_2_iommu on node -1
[ 85.170635] alloc irq_desc for 102 on node -1
[ 85.170636] alloc kstat_irqs on node -1
[ 85.170639] alloc irq_2_iommu on node -1
[ 85.170646] BUG: unable to handle kernel NULL pointer dereference
at 0000000000000088
As you can see igb and ixgbe are both alternating on create_irq_nr()
via pci_enable_msix() in their probe function.
ixgbe: While looping through irq_desc_ptrs[] via create_irq_nr() ixgbe
choses irq_desc_ptrs[102] and exits the loop, drops vector_lock and
calls dynamic_irq_init. Then it sets irq_desc_ptrs[102]->chip_data =
NULL via dynamic_irq_init().
igb: Grabs the vector_lock now and starts looping over irq_desc_ptrs[]
via create_irq_nr(). It gets to irq_desc_ptrs[102] and does this:
cfg_new = irq_desc_ptrs[102]->chip_data;
if (cfg_new->vector != 0)
continue;
This hits the NULL deref.
Another possible race exists via pci_disable_msix() in a driver or in
the number of error paths that call free_msi_irqs():
destroy_irq()
dynamic_irq_cleanup() which sets desc->chip_data = NULL
...race window...
desc->chip_data = cfg;
Remove the save and restore code for cfg in create_irq_nr() and
destroy_irq() and take the desc->lock when checking the irq_cfg.
Reported-and-analyzed-by: Brandon Philips <bphilips@suse.de>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <1265793639-15071-3-git-send-email-yinghai@kernel.org>
Signed-off-by: Brandon Phililps <bphilips@suse.de>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
