[ Upstream commit 72f17baf23 ]
If an OVS_ATTR_NESTED attribute type is found while walking
through netlink attributes, we call nlattr_set() recursively
passing the length table for the following nested attributes, if
different from the current one.
However, once we're done with those sub-nested attributes, we
should continue walking through attributes using the current
table, instead of using the one related to the sub-nested
attributes.
For example, given this sequence:
1 OVS_KEY_ATTR_PRIORITY
2 OVS_KEY_ATTR_TUNNEL
3 OVS_TUNNEL_KEY_ATTR_ID
4 OVS_TUNNEL_KEY_ATTR_IPV4_SRC
5 OVS_TUNNEL_KEY_ATTR_IPV4_DST
6 OVS_TUNNEL_KEY_ATTR_TTL
7 OVS_TUNNEL_KEY_ATTR_TP_SRC
8 OVS_TUNNEL_KEY_ATTR_TP_DST
9 OVS_KEY_ATTR_IN_PORT
10 OVS_KEY_ATTR_SKB_MARK
11 OVS_KEY_ATTR_MPLS
we switch to the 'ovs_tunnel_key_lens' table on attribute #3,
and we don't switch back to 'ovs_key_lens' while setting
attributes #9 to #11 in the sequence. As OVS_KEY_ATTR_MPLS
evaluates to 21, and the array size of 'ovs_tunnel_key_lens' is
15, we also get this kind of KASan splat while accessing the
wrong table:
[ 7654.586496] ==================================================================
[ 7654.594573] BUG: KASAN: global-out-of-bounds in nlattr_set+0x164/0xde9 [openvswitch]
[ 7654.603214] Read of size 4 at addr ffffffffc169ecf0 by task handler29/87430
[ 7654.610983]
[ 7654.612644] CPU: 21 PID: 87430 Comm: handler29 Kdump: loaded Not tainted 3.10.0-866.el7.test.x86_64 #1
[ 7654.623030] Hardware name: Dell Inc. PowerEdge R730/072T6D, BIOS 2.1.7 06/16/2016
[ 7654.631379] Call Trace:
[ 7654.634108] [<ffffffffb65a7c50>] dump_stack+0x19/0x1b
[ 7654.639843] [<ffffffffb53ff373>] print_address_description+0x33/0x290
[ 7654.647129] [<ffffffffc169b37b>] ? nlattr_set+0x164/0xde9 [openvswitch]
[ 7654.654607] [<ffffffffb53ff812>] kasan_report.part.3+0x242/0x330
[ 7654.661406] [<ffffffffb53ff9b4>] __asan_report_load4_noabort+0x34/0x40
[ 7654.668789] [<ffffffffc169b37b>] nlattr_set+0x164/0xde9 [openvswitch]
[ 7654.676076] [<ffffffffc167ef68>] ovs_nla_get_match+0x10c8/0x1900 [openvswitch]
[ 7654.684234] [<ffffffffb61e9cc8>] ? genl_rcv+0x28/0x40
[ 7654.689968] [<ffffffffb61e7733>] ? netlink_unicast+0x3f3/0x590
[ 7654.696574] [<ffffffffc167dea0>] ? ovs_nla_put_tunnel_info+0xb0/0xb0 [openvswitch]
[ 7654.705122] [<ffffffffb4f41b50>] ? unwind_get_return_address+0xb0/0xb0
[ 7654.712503] [<ffffffffb65d9355>] ? system_call_fastpath+0x1c/0x21
[ 7654.719401] [<ffffffffb4f41d79>] ? update_stack_state+0x229/0x370
[ 7654.726298] [<ffffffffb4f41d79>] ? update_stack_state+0x229/0x370
[ 7654.733195] [<ffffffffb53fe4b5>] ? kasan_unpoison_shadow+0x35/0x50
[ 7654.740187] [<ffffffffb53fe62a>] ? kasan_kmalloc+0xaa/0xe0
[ 7654.746406] [<ffffffffb53fec32>] ? kasan_slab_alloc+0x12/0x20
[ 7654.752914] [<ffffffffb53fe711>] ? memset+0x31/0x40
[ 7654.758456] [<ffffffffc165bf92>] ovs_flow_cmd_new+0x2b2/0xf00 [openvswitch]
[snip]
[ 7655.132484] The buggy address belongs to the variable:
[ 7655.138226] ovs_tunnel_key_lens+0xf0/0xffffffffffffd400 [openvswitch]
[ 7655.145507]
[ 7655.147166] Memory state around the buggy address:
[ 7655.152514] ffffffffc169eb80: 00 00 00 00 00 00 00 00 00 00 fa fa fa fa fa fa
[ 7655.160585] ffffffffc169ec00: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 7655.168644] >ffffffffc169ec80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 fa fa
[ 7655.176701] ^
[ 7655.184372] ffffffffc169ed00: fa fa fa fa 00 00 00 00 fa fa fa fa 00 00 00 05
[ 7655.192431] ffffffffc169ed80: fa fa fa fa 00 00 00 00 00 00 00 00 00 00 00 00
[ 7655.200490] ==================================================================
Reported-by: Hangbin Liu <liuhangbin@gmail.com>
Fixes: 982b527004 ("openvswitch: Fix mask generation for nested attributes.")
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7df40c2673 ]
Normally, a socket can not be freed/reused unless all its TX packets
left qdisc and were TX-completed. However connect(AF_UNSPEC) allows
this to happen.
With commit fc59d5bdf1 ("pkt_sched: fq: clear time_next_packet for
reused flows") we cleared f->time_next_packet but took no special
action if the flow was still in the throttled rb-tree.
Since f->time_next_packet is the key used in the rb-tree searches,
blindly clearing it might break rb-tree integrity. We need to make
sure the flow is no longer in the rb-tree to avoid this problem.
Fixes: fc59d5bdf1 ("pkt_sched: fq: clear time_next_packet for reused flows")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6ad4e91c6d ]
Add check of coalescing parameters received through ethtool are within
range of values supported by the HW.
Driver gets the coalescing rx/tx-usecs and rx/tx-frames as set by the
users through ethtool. The ethtool support up to 32 bit value for each.
However, mlx4 modify cq limits the coalescing time parameter and
coalescing frames parameters to 16 bits.
Return out of range error if user tries to set these parameters to
higher values.
Change type of sample-interval and adaptive_rx_coal parameters in mlx4
driver to u32 as the ethtool holds them as u32 and these parameters are
not limited due to mlx4 HW.
Fixes: c27a02cd94 ('mlx4_en: Add driver for Mellanox ConnectX 10GbE NIC')
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 14224923c3 ]
Currently, skb->len and skb->data_len are set to the page size, not
the packet size. This causes the frame check sequence to not be
located at the "end" of the packet resulting in ethernet frame check
errors. The driver does work currently, but stricter kernel facing
networking solutions like OpenVSwitch will drop these packets as
invalid.
These changes set the packet size correctly so that these errors no
longer occur. The length does not include the frame check sequence, so
that subtraction was removed.
Tested on Oracle/SUN Multithreaded 10-Gigabit Ethernet Network
Controller [108e:abcd] and validated in wireshark.
Signed-off-by: Rob Taglang <rob@taglang.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1b97013bfb ]
Fix more memory leaks in ip_cmsg_send() callers. Part of them were fixed
earlier in 919483096b.
* udp_sendmsg one was there since the beginning when linux sources were
first added to git;
* ping_v4_sendmsg one was copy/pasted in c319b4d76b.
Whenever return happens in udp_sendmsg() or ping_v4_sendmsg() IP options
have to be freed if they were allocated previously.
Add label so that future callers (if any) can use it instead of kfree()
before return that is easy to forget.
Fixes: c319b4d76b (net: ipv4: add IPPROTO_ICMP socket kind)
Signed-off-by: Andrey Ignatov <rdna@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e8238fc2bd ]
When we set a bond slave's master to bridge via ioctl, we only check
the IFF_BRIDGE_PORT flag. Although we will find the slave's real master
at netdev_master_upper_dev_link() later, it already does some settings
and allocates some resources. It would be better to return as early
as possible.
v1 -> v2:
use netdev_master_upper_dev_get() instead of netdev_has_any_upper_dev()
to check if we have a master, because not all upper devs are masters,
e.g. vlan device.
Reported-by: syzbot+de73361ee4971b6e6f75@syzkaller.appspotmail.com
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2be147f745 upstream.
pool can be indirectly controlled by user-space, hence leading to
a potential exploitation of the Spectre variant 1 vulnerability.
This issue was detected with the help of Smatch:
drivers/atm/zatm.c:1462 zatm_ioctl() warn: potential spectre issue
'zatm_dev->pool_info' (local cap)
Fix this by sanitizing pool before using it to index
zatm_dev->pool_info
Notice that given that speculation windows are large, the policy is
to kill the speculation on the first load and not worry if it can be
completed with a dependent load/store [1].
[1] https://marc.info/?l=linux-kernel&m=152449131114778&w=2
Cc: stable@vger.kernel.org
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit acf784bd0c upstream.
ioc_data.dev_num can be controlled by user-space, hence leading to
a potential exploitation of the Spectre variant 1 vulnerability.
This issue was detected with the help of Smatch:
net/atm/lec.c:702 lec_vcc_attach() warn: potential spectre issue
'dev_lec'
Fix this by sanitizing ioc_data.dev_num before using it to index
dev_lec. Also, notice that there is another instance in which array
dev_lec is being indexed using ioc_data.dev_num at line 705:
lec_vcc_added(netdev_priv(dev_lec[ioc_data.dev_num]),
Notice that given that speculation windows are large, the policy is
to kill the speculation on the first load and not worry if it can be
completed with a dependent load/store [1].
[1] https://marc.info/?l=linux-kernel&m=152449131114778&w=2
Cc: stable@vger.kernel.org
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dc432c3d7f upstream.
The regex match function regex_match_front() in the tracing filter logic,
was fixed to test just the pattern length from testing the entire test
string. That is, it went from strncmp(str, r->pattern, len) to
strcmp(str, r->pattern, r->len).
The issue is that str is not guaranteed to be nul terminated, and if r->len
is greater than the length of str, it can access more memory than is
allocated.
The solution is to add a simple test if (len < r->len) return 0.
Cc: stable@vger.kernel.org
Fixes: 285caad415 ("tracing/filters: Fix MATCH_FRONT_ONLY filter matching")
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 184add2ca2 upstream.
Richard Jones has reported that using med_power_with_dipm on a T450s
with a Sandisk SD7UB3Q256G1001 SSD (firmware version X2180501) is
causing the machine to hang.
Switching the LPM to max_performance fixes this, so it seems that
this Sandisk SSD does not handle LPM well.
Note in the past there have been bug-reports about the following
Sandisk models not working with min_power, so we may need to extend
the quirk list in the future: name - firmware
Sandisk SD6SB2M512G1022I - X210400
Sandisk SD6PP4M-256G-1006 - A200906
Cc: stable@vger.kernel.org
Cc: Richard W.M. Jones <rjones@redhat.com>
Reported-and-tested-by: Richard W.M. Jones <rjones@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 83e2d0587a upstream.
It doesn't support to run 32bit 'ip' to set xfrm objdect on 64bit host.
But the return value is unknown for user program:
ip xfrm policy list
RTNETLINK answers: Unknown error 524
Replace ENOTSUPP with EOPNOTSUPP:
ip xfrm policy list
RTNETLINK answers: Operation not supported
Signed-off-by: Yi Zhao <yi.zhao@windriver.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Nathan Harold <nharold@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b86e33075e upstream.
A dead loop can be triggered in f2fs_fiemap() using the test case
as below:
...
fd = open();
fallocate(fd, 0, 0, 4294967296);
ioctl(fd, FS_IOC_FIEMAP, fiemap_buf);
...
It's caused by an overflow in __get_data_block():
...
bh->b_size = map.m_len << inode->i_blkbits;
...
map.m_len is an unsigned int, and bh->b_size is a size_t which is 64 bits
on 64 bits archtecture, type conversion from an unsigned int to a size_t
will result in an overflow.
In the above-mentioned case, bh->b_size will be zero, and f2fs_fiemap()
will call get_data_block() at block 0 again an again.
Fix this by adding a force conversion before left shift.
Signed-off-by: Wei Fang <fangwei1@huawei.com>
Acked-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b8b784958e upstream.
Syzbot has reported that it can hit a NULL pointer dereference in
wb_workfn() due to wb->bdi->dev being NULL. This indicates that
wb_workfn() was called for an already unregistered bdi which should not
happen as wb_shutdown() called from bdi_unregister() should make sure
all pending writeback works are completed before bdi is unregistered.
Except that wb_workfn() itself can requeue the work with:
mod_delayed_work(bdi_wq, &wb->dwork, 0);
and if this happens while wb_shutdown() is waiting in:
flush_delayed_work(&wb->dwork);
the dwork can get executed after wb_shutdown() has finished and
bdi_unregister() has cleared wb->bdi->dev.
Make wb_workfn() use wakeup_wb() for requeueing the work which takes all
the necessary precautions against racing with bdi unregistration.
CC: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
CC: Tejun Heo <tj@kernel.org>
Fixes: 839a8e8660
Reported-by: syzbot <syzbot+9873874c735f2892e7e9@syzkaller.appspotmail.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b1993a2de1 upstream.
syzbot reported :
BUG: KMSAN: uninit-value in rtnh_ok include/net/nexthop.h:11 [inline]
BUG: KMSAN: uninit-value in fib_count_nexthops net/ipv4/fib_semantics.c:469 [inline]
BUG: KMSAN: uninit-value in fib_create_info+0x554/0x8d20 net/ipv4/fib_semantics.c:1091
@remaining is an integer, coming from user space.
If it is negative we want rtnh_ok() to return false.
Fixes: 4e902c5741 ("[IPv4]: FIB configuration using struct fib_config")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2b63f1329d upstream.
musb_start_urb() doesn't check the pass-in parameter if it is NULL. But
in musb_bulk_nak_timeout() the parameter passed to musb_start_urb() is
returned from first_qh(), which could be NULL.
So wrap the musb_start_urb() call here with a if condition check to
avoid the potential NULL pointer dereference.
Fixes: f283862f3b ("usb: musb: NAK timeout scheme on bulk TX endpoint")
Cc: stable@vger.kernel.org # v3.7+
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c3a65808f0 upstream.
Reimplement interface masking using device flags stored directly in the
device-id table. This will make it easier to add and maintain device-id
entries by using a more compact and readable notation compared to the
current implementation (which manages pairs of masks in separate
blacklist structs).
Two convenience macros are used to flag an interface as either reserved
or as not supporting modem-control requests:
{ USB_DEVICE(TELIT_VENDOR_ID, TELIT_PRODUCT_ME910_DUAL_MODEM),
.driver_info = NCTRL(0) | RSVD(3) },
For now, we limit the highest maskable interface number to seven, which
allows for (up to 16) additional device flags to be added later should
need arise.
Note that this will likely need to be backported to stable in order to
make future device-id backports more manageable.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fb5ee84ea7 upstream.
Some non-compliant high-speed USB devices have bulk endpoints with a
1024-byte maxpacket size. Although such endpoints don't work with
xHCI host controllers, they do work with EHCI controllers. We used to
accept these invalid sizes (with a warning), but we no longer do
because of an unintentional change introduced by commit aed9d65ac3
("USB: validate wMaxPacketValue entries in endpoint descriptors").
This patch restores the old behavior, so that people with these
peculiar devices can use them without patching their kernels by hand.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Suggested-by: Elvinas <elvinas@veikia.lt>
Fixes: aed9d65ac3 ("USB: validate wMaxPacketValue entries in endpoint descriptors")
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4842ed5bfc upstream.
If we get an invalid device configuration from a palm 3 type device, we
might incorrectly parse things, and we have the potential to crash in
"interesting" ways.
Fix this up by verifying the size of the configuration passed to us by
the device, and only if it is correct, will we handle it.
Note that this also fixes an information leak of slab data.
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Reviewed-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ johan: add comment about the info leak ]
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e538409257 upstream.
Commit 65c7923057 tried to clear the custom firmware path on exit by
writing a single space to the firmware_class.path parameter. This
doesn't work because nothing strips this space from the value stored
and fw_get_filesystem_firmware() only ignores zero-length paths.
Instead, write a null byte.
Fixes: 0a8adf5847 ("test: add firmware_class loader test")
Fixes: 65c7923057 ("test_firmware: fix setting old custom fw path back on exit")
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Acked-by: Luis R. Rodriguez <mcgrof@kernel.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4f32ac2e45 upstream.
Before the change, if the user passed a static rate value different
than zero and the FW doesn't support static rate,
it would end up configuring rate of 2.5 GBps.
Fix this by using rate 0; unlimited, in cases where FW
doesn't support static rate configuration.
Cc: <stable@vger.kernel.org> # 3.10
Fixes: e126ba97db ("mlx5: Add driver for Mellanox Connect-IB adapters")
Reviewed-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Danit Goldberg <danitg@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 09abfe7b5b upstream.
The RDMA CM will select a source device and address by consulting
the routing table if no source address is passed into
rdma_resolve_address(). Userspace will ask for this by passing an
all-zero source address in the RESOLVE_IP command. Unfortunately
the new check for non-zero address size rejects this with EINVAL,
which breaks valid userspace applications.
Fix this by explicitly allowing a zero address family for the source.
Fixes: 2975d5de64 ("RDMA/ucma: Check AF family prior resolving address")
Cc: <stable@vger.kernel.org>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7d83fb1425 upstream.
During the "insert range" fallocate operation, i_size grows by the
specified 'len' bytes. XFS verifies that i_size + len < s_maxbytes, as
it should. But this comparison is done using the signed 'loff_t', and
'i_size + len' can wrap around to a negative value, causing the check to
incorrectly pass, resulting in an inode with "negative" i_size. This is
possible on 64-bit platforms, where XFS sets s_maxbytes = LLONG_MAX.
ext4 and f2fs don't run into this because they set a smaller s_maxbytes.
Fix it by using subtraction instead.
Reproducer:
xfs_io -f file -c "truncate $(((1<<63)-1))" -c "finsert 0 4096"
Fixes: a904b1ca57 ("xfs: Add support FALLOC_FL_INSERT_RANGE for fallocate")
Cc: <stable@vger.kernel.org> # v4.1+
Originally-From: Eric Biggers <ebiggers@google.com>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
[darrick: fix signed integer addition overflow too]
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f372b81101 upstream.
This patch adds the correct platform data information for the Caroline
Chromebook, so that the mouse button does not get stuck in pressed state
after the first click.
The Samus button keymap and platform data definition are the correct
ones for Caroline, so they have been reused here.
Signed-off-by: Vittorio Gambaletta <linuxbugs@vittgam.net>
Signed-off-by: Salvatore Bellizzi <lkml@seppia.net>
Tested-by: Guenter Roeck <groeck@chromium.org>
Cc: stable@vger.kernel.org
[dtor: adjusted vendor spelling to match shipping firmware]
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
