commit 0946b2fb38 upstream.
The help for FIRMWARE_IN_KERNEL still references the firmware_install
command that was recently removed by commit 5620a0d1aa ("firmware:
delete in-kernel firmware").
Clean up the message to direct the user to their distribution's
linux-firmware package, and remove any reference to firmware being
included in the kernel source tree.
Fixes: 5620a0d1aa ("firmware: delete in-kernel firmware").
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Robin H. Johnson <robbat2@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 297d6b6e56 upstream.
While reading in more than one block (50) of KVP records, the allocation
goes per block, but the reads used the total number of allocated records
(without resetting the pointer/stream). This causes the records buffer to
overrun when the refresh reads more than one block over the previous
capacity (e.g. reading more than 100 KVP records whereas the in-memory
database was empty before).
Fix this by reading the correct number of KVP records from file each time.
Signed-off-by: Paul Meyer <Paul.Meyer@microsoft.com>
Signed-off-by: Long Li <longli@microsoft.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7fa32e5ec2 upstream.
The current rescind processing code will not correctly handle
the case where the host immediately rescinds a channel that has
been offerred. In this case, we could be blocked in the open call and
since the channel is rescinded, the host will not respond and we could
be blocked forever in the vmbus open call.i Fix this problem.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6702abb3bf upstream.
The direction_output callback of the gpio_chip structure is supposed to
set the output direction but also to set the value of the gpio. For the
armada-37xx driver this callback acted as the gpio_set_direction callback
for the pinctrl.
This patch fixes the behavior of the direction_output callback by also
applying the value received as parameter.
Fixes: 5715092a45 ("pinctrl: armada-37xx: Add gpio support")
Reported-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 96748823c4 upstream.
The Meson GXBB and newer SoCs have a few more registers than the older
Meson8 and Meson8b SoCs.
Use a separate regmap config to limit the older SoCs to the DELTA_10
register.
Fixes: 6c76ed31cd ("iio: adc: meson-saradc: add Meson8b SoC compatibility")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d85eed9f57 upstream.
Meson8 and Meson8b do not have the MESON_SAR_ADC_REG11 register. The
bandgap setting for these SoCs is configured in the
MESON_SAR_ADC_DELTA_10 register instead.
Make the driver aware of this difference and use the correct bandgap
register depending on the SoC.
This has worked fine on Meson8 and Meson8b because the bootloader is
already initializing the bandgap setting.
Fixes: 6c76ed31cd ("iio: adc: meson-saradc: add Meson8b SoC compatibility")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7a6b0420d2 upstream.
Meson8 and Meson8b SoCs use the the SAR ADC gate clock provided by the
MESON_SAR_ADC_REG3 register within the SAR ADC register area.
According to the datasheet (and the existing MESON_SAR_ADC_REG3_CLK_EN
definition) the gate is on bit 30.
The fls() function returns the last set bit, which is "bit index + 1"
(fls(MESON_SAR_ADC_REG3_CLK_EN) returns 31). Fix this by switching to
__ffs() which returns the first set bit, which is bit 30 in our case.
This off by one error results in the ADC not being usable on devices
where the bootloader did not enable the clock.
Fixes: 3adbf34273 ("iio: adc: add a driver for the SAR ADC found in Amlogic Meson SoCs")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 81b039ec36 upstream.
Function platform_get_irq_byname() returns a negative error code on
failure, and a zero or positive number on success. However, in function
cpcap_adc_probe(), positive IRQ numbers are also taken as error cases.
Use "if (ddata->irq < 0)" instead of "if (!ddata->irq)" to validate the
return value of platform_get_irq_byname().
Signed-off-by: Pan Bian <bianpan2016@163.com>
Fixes: 25ec249632 ("iio: adc: cpcap: Add minimal support for CPCAP PMIC ADC")
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6d745ee8b5 upstream.
The ADC driver can trigger on either the timer or the lptim
trigger, but it only uses a Kconfig 'select' statement
to ensure that the first of the two is present. When the lptim
trigger is enabled as a loadable module, and the adc driver
is built-in, we now get a link error:
drivers/iio/adc/stm32-adc.o: In function `stm32_adc_get_trig_extsel':
stm32-adc.c:(.text+0x4e0): undefined reference to `is_stm32_lptim_trigger'
We could use a second 'select' statement and always have both
trigger drivers enabled when the adc driver is, but it seems that
the lptimer trigger was intentionally left optional, so it seems
better to keep it that way.
This adds a hack to use 'IS_REACHABLE()' rather than 'IS_ENABLED()',
which avoids the link error, but instead leads to the lptimer trigger
not being used in the broken configuration. I've added a runtime
warning for this case to help users figure out what they did wrong
if this should ever be done by accident.
Fixes: f0b638a7f6 ("iio: adc: stm32: add support for lptimer triggers")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 91785de6f9 upstream.
Don't rely on can_get_echo_skb() return value to wake the network tx
queue up: can_get_echo_skb() returns 0 if the echo array slot was not
occupied, but also when the DLC of the released echo frame was 0.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 12147edc43 upstream.
In mcba_usb, we have observed that when you unplug the device, the driver will
endlessly resubmit failing URBs, which can cause CPU stalls. This issue
is fixed in mcba_usb by catching the codes seen on device disconnect
(-EPIPE and -EPROTO).
This driver also resubmits in the case of -EPIPE and -EPROTO, so fix it
in the same way.
Signed-off-by: Martin Kelly <mkelly@xevo.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7a31ced3de upstream.
In mcba_usb, we have observed that when you unplug the device, the driver will
endlessly resubmit failing URBs, which can cause CPU stalls. This issue
is fixed in mcba_usb by catching the codes seen on device disconnect
(-EPIPE and -EPROTO).
This driver also resubmits in the case of -EPIPE and -EPROTO, so fix it
in the same way.
Signed-off-by: Martin Kelly <mkelly@xevo.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bd352e1adf upstream.
In mcba_usb, we have observed that when you unplug the device, the driver will
endlessly resubmit failing URBs, which can cause CPU stalls. This issue
is fixed in mcba_usb by catching the codes seen on device disconnect
(-EPIPE and -EPROTO).
This driver also resubmits in the case of -EPIPE and -EPROTO, so fix it
in the same way.
Signed-off-by: Martin Kelly <mkelly@xevo.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c7f3302330 upstream.
When we unplug the device, we can see both -EPIPE and -EPROTO depending
on exact timing and what system we run on. If we continue to resubmit
URBs, they will immediately fail, and they can cause stalls, especially
on slower CPUs.
Fix this by not resubmitting on -EPROTO, as we already do on -EPIPE.
Signed-off-by: Martin Kelly <mkelly@xevo.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6aa8d59455 upstream.
In mcba_usb, we have observed that when you unplug the device, the driver will
endlessly resubmit failing URBs, which can cause CPU stalls. This issue
is fixed in mcba_usb by catching the codes seen on device disconnect
(-EPIPE and -EPROTO).
This driver also resubmits in the case of -EPIPE and -EPROTO, so fix it
in the same way.
Signed-off-by: Martin Kelly <mkelly@xevo.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e84f44eb55 upstream.
The conditon in the while-loop becomes true when actual_length is less than
2 (MSG_HEADER_LEN). In best case we end up with a former, already
dispatched msg, that got msg->len greater than actual_length. This will
result in a "Format error" error printout.
Problem seen when unplugging a Kvaser USB device connected to a vbox guest.
warning: comparison between signed and unsigned integer expressions
[-Wsign-compare]
Signed-off-by: Jimmy Assarsson <jimmyassarsson@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f6c23b174c upstream.
After commit d75b1ade56 ("net: less interrupt masking in NAPI") napi
repoll is done only when work_done == budget.
So we need to return budget if there are still packets to receive.
Signed-off-by: Oliver Stäbler <oliver.staebler@bytesatwork.ch>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5c2cb02edf upstream.
PCI/PCIe drivers for PEAK-System CAN/CAN-FD interfaces do some access to the
PCI config during probing. In case one of these accesses fails, a POSITIVE
PCIBIOS_xxx error code is returned back. This POSITIVE error code MUST be
converted into a NEGATIVE errno for the probe() function to indicate it
failed. Using the pcibios_err_to_errno() function, we make sure that the
return code will always be negative.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1cb35a33a2 upstream.
Currently, when you disconnect the device, the driver infinitely
resubmits all URBs, so you see:
Rx URB aborted (-32)
in an infinite loop.
Fix this by catching -EPIPE (what we get in urb->status when the device
disconnects) and not resubmitting.
With this patch, I can plug and unplug many times and the driver
recovers correctly.
Signed-off-by: Martin Kelly <mkelly@xevo.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a3acc69608 upstream.
The specification says that the Reserved1 field in OS_DESC_EXT_COMPAT
must have the value "1", but when this feature was first implemented we
rejected any non-zero values.
This was adjusted to accept all non-zero values (while now rejecting
zero) in commit 53642399aa ("usb: gadget: f_fs: Fix wrong check on
reserved1 of OS_DESC_EXT_COMPAT"), but that breaks any userspace
programs that worked previously by returning EINVAL when Reserved1 == 0
which was previously the only value that succeeded!
If we just set the field to "1" ourselves, both old and new userspace
programs continue to work correctly and, as a bonus, old programs are
now compliant with the specification without having to fix anything
themselves.
Fixes: 53642399aa ("usb: gadget: f_fs: Fix wrong check on reserved1 of OS_DESC_EXT_COMPAT")
Signed-off-by: John Keeping <john@metanate.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 90dbad8cd6 upstream.
Make sure to hold the tty lock as required when calling tty-driver
close() (e.g. to avoid racing with hangup()).
Note that the serport active flag is currently set under the lock at
controller open, but really isn't protected by it.
Fixes: cd6484e183 ("serdev: Introduce new bus for serial attached devices")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8bcd4e6a8d upstream.
Make sure to use a properly refcounted tty_struct in write_wake up to
avoid dereferencing a NULL-pointer when a port is being hung up.
Fixes: bed35c6dfa ("serdev: add a tty port controller driver")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit eb28168362 upstream.
The receive_buf tty-port callback should return the number of bytes
accepted and must specifically never return a negative errno (or a value
larger than the buffer size) to the tty layer.
A serdev driver not providing a receive_buf callback would currently
cause the flush_to_ldisc() worker to spin in a tight loop when the tty
buffer pointers are incremented with -EINVAL (-22) after data has been
received.
A serdev driver occasionally returning a negative errno (or a too large
byte count) could cause information leaks or crashes when accessing
memory outside the tty buffers in consecutive callbacks.
Fixes: cd6484e183 ("serdev: Introduce new bus for serial attached devices")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a4f0927ef5 upstream.
Currently UDC core calls ->udc_set_speed() with the speed parameter
containing the maximum speed supported by the gadget function
driver. This might very well be more than that supported by the
UDC controller driver.
Select the lesser of the 2 speeds so both UDC and gadget function
driver are operating within limits.
This fixes PHY Erratic errors and 2 second enumeration delay on
TI's AM437x platforms.
Fixes: 6099eca796ae ("usb: gadget: core: introduce ->udc_set_speed() method")
Reported-by: Dylan Howey <Dylan.Howey@tennantco.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a58204ab91 upstream.
This controller on R-Car Gen3 has 6 pipes that included PIPE 0 for
control actually. But, the datasheet has error in writing as it has
31 pipes. (However, the previous code defined 30 pipes wrongly...)
Anyway, this patch fixes it.
Fixes: 746bfe63bb ("usb: gadget: renesas_usb3: add support for Renesas USB3.0 peripheral controller")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b562c171cf upstream.
The refcount_t protection on x86 was not intended to use the stricter
GPL export. This adjusts the linkage again to avoid a regression in
the availability of the refcount API.
Reported-by: Dave Airlie <airlied@gmail.com>
Fixes: 7a46ec0e2f ("locking/refcounts, x86/asm: Implement fast refcount overflow protection")
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Ivan Kozik <ivan@ludios.org>
Cc: Thomas Backlund <tmb@mageia.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1d5a31582e upstream.
The variable temp is incorrectly being updated, instead it should
be offset otherwise the loop just reads the same capability value
and loops forever. Thanks to Alan Stern for pointing out the
correct fix to my original fix. Fix also cleans up clang warning:
drivers/usb/host/ehci-dbg.c:840:4: warning: Value stored to 'temp'
is never read
Fixes: d49d431744 ("USB: misc ehci updates")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 81cf4a4536 upstream.
As most of BOS descriptors are longer in length than their header
'struct usb_dev_cap_header', comparing solely with it is not sufficient
to avoid out-of-bounds access to BOS descriptors.
This patch adds descriptor type specific length check in
usb_get_bos_descriptor() to fix the issue.
Signed-off-by: Masakazu Mokuno <masakazu.mokuno@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e4ec40ec4b upstream.
xHC can generate two events for a short transfer if the short TRB and
last TRB in the TD are not the same TRB.
The driver will handle the TD after the first short event, and remove
it from its internal list. Driver then incorrectly prints a warning
for the second event:
"WARN Event TRB for slot x ep y with no TDs queued"
Fix this by not printing a warning if we get a event on a empty list
if the previous event was a short event.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 33c309ebc7 upstream.
Fix bus-node lookup during registration, which ended up searching the whole
device tree depth-first starting at the parent (or grand parent) rather
than just matching on its children.
To make things worse, the parent (or grand-parent) node could end being
prematurely freed as well.
Fixes: ef6a7bcfb0 ("usb: ulpi: Support device discovery via DT")
Reported-by: Peter Robinson <pbrobinson@gmail.com>
Reported-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 973593a960 upstream.
Sometimes the USB device gets confused about the state of the initialization and
the connection fails. In particular, the device thinks that it's already set up
and running while the host thinks the device still needs to be configured. To
work around this issue, power-cycle the hub's output to issue a sort of "reset"
to the device. This makes the device restart its state machine and then the
initialization succeeds.
This fixes problems where the kernel reports a list of errors like this:
usb 1-1.3: device not accepting address 19, error -71
The end result is a non-functioning device. After this patch, the sequence
becomes like this:
usb 1-1.3: new high-speed USB device number 18 using ci_hdrc
usb 1-1.3: device not accepting address 18, error -71
usb 1-1.3: new high-speed USB device number 19 using ci_hdrc
usb 1-1.3: device not accepting address 19, error -71
usb 1-1-port3: attempt power cycle
usb 1-1.3: new high-speed USB device number 21 using ci_hdrc
usb-storage 1-1.3:1.2: USB Mass Storage device detected
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c5f39d0786 upstream.
crypto_ahash_import() may be called either after
crypto_ahash_init() or without such call. Right now
we always internally call init() as part of
import(), thus leaking memory and mappings if the
user has already called init() herself.
Fix this by only calling init() internally if the
state is not already initialized.
Fixes: commit 454527d0d9 ("staging: ccree: fix hash import/export")
Signed-off-by: Gilad Ben-Yossef <gilad@benyossef.com>
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8a2d71a3f2 upstream.
Per Documentation/kprobes.txt, probe handlers need to be invoked with
preemption disabled. Update optimized_callback() to do so. Also move
get_kprobe_ctlblk() invocation post preemption disable, since it
accesses pre-cpu data.
This was not an issue so far since optprobes wasn't selected if
CONFIG_PREEMPT was enabled. Commit a30b85df7d ("kprobes: Use
synchronize_rcu_tasks() for optprobe with CONFIG_PREEMPT=y") changes
this.
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit dd92d5ea20 ]
Check return values from call to devm_kzalloc() and devm_kmemup()
in order to prevent a NULL pointer dereference.
This issue was detected using Coccinelle and the following semantic patch:
@@
expression x;
identifier fld;
@@
* x = devm_kzalloc(...);
... when != x == NULL
x->fld
Fixes: 7ba9df54b0 ("iio: multiplexer: new iio category and iio-mux driver")
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Acked-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
