[ Upstream commit 4bd5e02a2e ]
Trusted VF with unicast promiscuous mode set, could listen to TX
traffic of other VFs.
Set unicast promiscuous mode to RX traffic, if VSI has port VLAN
configured. Rename misleading I40E_AQC_SET_VSI_PROMISC_TX bit to
I40E_AQC_SET_VSI_PROMISC_RX_ONLY. Aligned unicast promiscuous with
VLAN to the one without VLAN.
Fixes: 6c41a76069 ("i40e: Add promiscuous on VLAN support")
Fixes: 3b1200891b ("i40e: When in promisc mode apply promisc mode to Tx Traffic as well")
Signed-off-by: Przemyslaw Patynowski <przemyslawx.patynowski@intel.com>
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 796a58fe2b ]
Most of the DAPM widgets for DSP ASoC components reuse reg field
of the widgets for its internal calculations, however these are not
real registers. So read/writes to these numbers are not really
valid. However ASoC core will read these registers to get default
state during startup.
With recent changes to ASoC core, every register read/write
failures are reported very verbosely. Prior to this fails to reads
are totally ignored, so we never saw any error messages.
To fix this add dummy read/write function to return default value.
Fixes: e3a33673e8 ("ASoC: qdsp6: q6routing: Add q6routing driver")
Reported-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20200811120205.21805-2-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bf9a379d09 ]
Currently, add_system_zone() just silently merges two added system zones
that overlap. However the overlap should not happen and it generally
suggests that some unrelated metadata overlap which indicates the fs is
corrupted. We should have caught such problems earlier (e.g. in
ext4_check_descriptors()) but add this check as another line of defense.
In later patch we also use this for stricter checking of journal inode
extent tree.
Reviewed-by: Lukas Czerner <lczerner@redhat.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Link: https://lore.kernel.org/r/20200728130437.7804-3-jack@suse.cz
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5872331b3d ]
If for any reason a directory passed to do_split() does not have enough
active entries to exceed half the size of the block, we can end up
iterating over all "count" entries without finding a split point.
In this case, count == move, and split will be zero, and we will
attempt a negative index into map[].
Guard against this by detecting this case, and falling back to
split-to-half-of-count instead; in this case we will still have
plenty of space (> half blocksize) in each split block.
Fixes: ef2b02d3e6 ("ext34: ensure do_split leaves enough free space in both blocks")
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Reviewed-by: Andreas Dilger <adilger@dilger.ca>
Reviewed-by: Jan Kara <jack@suse.cz>
Link: https://lore.kernel.org/r/f53e246b-647c-64bb-16ec-135383c70ad7@redhat.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 96cf2a2c75 ]
If xfs_sysfs_init is called with parent_kobj == NULL, UBSAN
shows the following warning:
UBSAN: null-ptr-deref in ./fs/xfs/xfs_sysfs.h:37:23
member access within null pointer of type 'struct xfs_kobj'
Call Trace:
dump_stack+0x10e/0x195
ubsan_type_mismatch_common+0x241/0x280
__ubsan_handle_type_mismatch_v1+0x32/0x40
init_xfs_fs+0x12b/0x28f
do_one_initcall+0xdd/0x1d0
do_initcall_level+0x151/0x1b6
do_initcalls+0x50/0x8f
do_basic_setup+0x29/0x2b
kernel_init_freeable+0x19f/0x20b
kernel_init+0x11/0x1e0
ret_from_fork+0x22/0x30
Fix it by checking parent_kobj before the code accesses its member.
Signed-off-by: Eiichi Tsukata <devel@etsukata.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
[darrick: minor whitespace edits]
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 481a0d7422 ]
The loop may exist if vq->broken is true,
virtqueue_get_buf_ctx_packed or virtqueue_get_buf_ctx_split
will return NULL, so virtnet_poll will reschedule napi to
receive packet, it will lead cpu usage(si) to 100%.
call trace as below:
virtnet_poll
virtnet_receive
virtqueue_get_buf_ctx
virtqueue_get_buf_ctx_packed
virtqueue_get_buf_ctx_split
virtqueue_napi_complete
virtqueue_poll //return true
virtqueue_napi_schedule //it will reschedule napi
to fix this, return false if vq is broken in virtqueue_poll.
Signed-off-by: Mao Wenan <wenan.mao@linux.alibaba.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Link: https://lore.kernel.org/r/1596354249-96204-1-git-send-email-wenan.mao@linux.alibaba.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4daca379c7 ]
The MSR_TURBO_RATIO_LIMIT can be 0. This is not an error. User can update
this MSR via BIOS settings on some systems or can use msr tools to update.
Also some systems boot with value = 0.
This results in display of cpufreq/cpuinfo_max_freq wrong. This value
will be equal to cpufreq/base_frequency, even though turbo is enabled.
But platform will still function normally in HWP mode as we get max
1-core frequency from the MSR_HWP_CAPABILITIES. This MSR is already used
to calculate cpu->pstate.turbo_freq, which is used for to set
policy->cpuinfo.max_freq. But some other places cpu->pstate.turbo_pstate
is used. For example to set policy->max.
To fix this, also update cpu->pstate.turbo_pstate when updating
cpu->pstate.turbo_freq.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 798b7347e4 ]
The log of UAF problem is listed below.
BUG: KASAN: use-after-free in jffs2_rmdir+0xa4/0x1cc [jffs2] at addr c1f165fc
Read of size 4 by task rm/8283
=============================================================================
BUG kmalloc-32 (Tainted: P B O ): kasan: bad access detected
-----------------------------------------------------------------------------
INFO: Allocated in 0xbbbbbbbb age=3054364 cpu=0 pid=0
0xb0bba6ef
jffs2_write_dirent+0x11c/0x9c8 [jffs2]
__slab_alloc.isra.21.constprop.25+0x2c/0x44
__kmalloc+0x1dc/0x370
jffs2_write_dirent+0x11c/0x9c8 [jffs2]
jffs2_do_unlink+0x328/0x5fc [jffs2]
jffs2_rmdir+0x110/0x1cc [jffs2]
vfs_rmdir+0x180/0x268
do_rmdir+0x2cc/0x300
ret_from_syscall+0x0/0x3c
INFO: Freed in 0x205b age=3054364 cpu=0 pid=0
0x2e9173
jffs2_add_fd_to_list+0x138/0x1dc [jffs2]
jffs2_add_fd_to_list+0x138/0x1dc [jffs2]
jffs2_garbage_collect_dirent.isra.3+0x21c/0x288 [jffs2]
jffs2_garbage_collect_live+0x16bc/0x1800 [jffs2]
jffs2_garbage_collect_pass+0x678/0x11d4 [jffs2]
jffs2_garbage_collect_thread+0x1e8/0x3b0 [jffs2]
kthread+0x1a8/0x1b0
ret_from_kernel_thread+0x5c/0x64
Call Trace:
[c17ddd20] [c02452d4] kasan_report.part.0+0x298/0x72c (unreliable)
[c17ddda0] [d2509680] jffs2_rmdir+0xa4/0x1cc [jffs2]
[c17dddd0] [c026da04] vfs_rmdir+0x180/0x268
[c17dde00] [c026f4e4] do_rmdir+0x2cc/0x300
[c17ddf40] [c001a658] ret_from_syscall+0x0/0x3c
The root cause is that we don't get "jffs2_inode_info.sem" before
we scan list "jffs2_inode_info.dents" in function jffs2_rmdir.
This patch add codes to get "jffs2_inode_info.sem" before we scan
"jffs2_inode_info.dents" to slove the UAF problem.
Signed-off-by: Zhe Li <lizhe67@huawei.com>
Reviewed-by: Hou Tao <houtao1@huawei.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f959b5d037 ]
xfs_trans_dqresv is the function that we use to make reservations
against resource quotas. Each resource contains two counters: the
q_core counter, which tracks resources allocated on disk; and the dquot
reservation counter, which tracks how much of that resource has either
been allocated or reserved by threads that are working on metadata
updates.
For disk blocks, we compare the proposed reservation counter against the
hard and soft limits to decide if we're going to fail the operation.
However, for inodes we inexplicably compare against the q_core counter,
not the incore reservation count.
Since the q_core counter is always lower than the reservation count and
we unlock the dquot between reservation and transaction commit, this
means that multiple threads can reserve the last inode count before we
hit the hard limit, and when they commit, we'll be well over the hard
limit.
Fix this by checking against the incore inode reservation counter, since
we would appear to maintain that correctly (and that's what we report in
GETQUOTA).
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Allison Collins <allison.henderson@oracle.com>
Reviewed-by: Chandan Babu R <chandanrlinux@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 64d2642251 ]
During a connection tear down, the Receive queue is flushed before
the device resources are freed. Typically, all the Receives flush
with IB_WR_FLUSH_ERR.
However, any pending successful Receives flush with IB_WR_SUCCESS,
and the server automatically posts a fresh Receive to replace the
completing one. This happens even after the connection has closed
and the RQ is drained. Receives that are posted after the RQ is
drained appear never to complete, causing a Receive resource leak.
The leaked Receive buffer is left DMA-mapped.
To prevent these late-posted recv_ctxt's from leaking, block new
Receive posting after XPT_CLOSE is set.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bdee0e793c ]
The Cache Control Register (CACR) of the ColdFire V3 has bits that
control high level caching functions, and also enable/disable the use
of the alternate stack pointer register (the EUSP bit) to provide
separate supervisor and user stack pointer registers. The code as
it is today will blindly clear the EUSP bit on cache actions like
invalidation. So it is broken for this case - and that will result
in failed booting (interrupt entry and exit processing will be
completely hosed).
This only affects ColdFire V3 parts that support the alternate stack
register (like the 5329 for example) - generally speaking new parts do,
older parts don't. It has no impact on ColdFire V3 parts with the single
stack pointer, like the 5307 for example.
Fix the cache bit defines used, so they maintain the EUSP bit when
carrying out cache actions through the CACR register.
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9c487b0b0e ]
If platform_driver_register() fails within vpss_init() resources are not
cleaned up. The patch fixes this issue by introducing the corresponding
error handling.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Evgeny Novikov <novikov@ispras.ru>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fc0456458d ]
budget_register() has no error handling after its failure.
Add the missed undo functions for error handling to fix it.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ddf75be47c ]
CONFIG_OF_DYNAMIC and CONFIG_ACPI allow adding SPI devices at runtime
using a DeviceTree overlay or DSDT patch. CONFIG_SPI_SLAVE allows the
same via sysfs.
But there are no precautions to prevent adding a device below a
controller that's being removed. Such a device is unusable and may not
even be able to unbind cleanly as it becomes inaccessible once the
controller has been torn down. E.g. it is then impossible to quiesce
the device's interrupt.
of_spi_notify() and acpi_spi_notify() do hold a ref on the controller,
but otherwise run lockless against spi_unregister_controller().
Fix by holding the spi_add_lock in spi_unregister_controller() and
bailing out of spi_add_device() if the controller has been unregistered
concurrently.
Fixes: ce79d54ae4 ("spi/of: Add OF notifier handler")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org # v3.19+
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Octavian Purdila <octavian.purdila@intel.com>
Cc: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
Link: https://lore.kernel.org/r/a8c3205088a969dc8410eec1eba9aface60f36af.1596451035.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 26c7295be0 upstream.
when we create a kthread with ktrhead_create_on_cpu(),the child thread
entry is ktread.c:ktrhead() which will be preempted by the parent after
call complete(done) while schedule() is not called yet,then the parent
will call wait_task_inactive(child) but the child is still on the runqueue,
so the parent will schedule_hrtimeout() for 1 jiffy,it will waste a lot of
time,especially on startup.
parent child
ktrhead_create_on_cpu()
wait_fo_completion(&done) -----> ktread.c:ktrhead()
|----- complete(done);--wakeup and preempted by parent
kthread_bind() <------------| |-> schedule();--dequeue here
wait_task_inactive(child) |
schedule_hrtimeout(1 jiffy) -|
So we hope the child just wakeup parent but not preempted by parent, and the
child is going to call schedule() soon,then the parent will not call
schedule_hrtimeout(1 jiffy) as the child is already dequeue.
The same issue for ktrhead_park()&&kthread_parkme().
This patch can save 120ms on rk312x startup with CONFIG_HZ=300.
Signed-off-by: Liang Chen <cl@rock-chips.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Link: https://lkml.kernel.org/r/20200306070133.18335-2-cl@rock-chips.com
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2d9a2c5f58 upstream.
Before v4.15 commit 75492a5156 ("s390/scsi: Convert timers to use
timer_setup()"), we intentionally only passed zfcp_adapter as context
argument to zfcp_fsf_request_timeout_handler(). Since we only trigger
adapter recovery, it was unnecessary to sync against races between timeout
and (late) completion. Likewise, we only passed zfcp_erp_action as context
argument to zfcp_erp_timeout_handler(). Since we only wakeup an ERP action,
it was unnecessary to sync against races between timeout and (late)
completion.
Meanwhile the timeout handlers get timer_list as context argument and do a
timer-specific container-of to zfcp_fsf_req which can have been freed.
Fix it by making sure that any request timeout handlers, that might just
have started before del_timer(), are completed by using del_timer_sync()
instead. This ensures the request free happens afterwards.
Space time diagram of potential use-after-free:
Basic idea is to have 2 or more pending requests whose timeouts run out at
almost the same time.
req 1 timeout ERP thread req 2 timeout
---------------- ---------------- ---------------------------------------
zfcp_fsf_request_timeout_handler
fsf_req = from_timer(fsf_req, t, timer)
adapter = fsf_req->adapter
zfcp_qdio_siosl(adapter)
zfcp_erp_adapter_reopen(adapter,...)
zfcp_erp_strategy
...
zfcp_fsf_req_dismiss_all
list_for_each_entry_safe
zfcp_fsf_req_complete 1
del_timer 1
zfcp_fsf_req_free 1
zfcp_fsf_req_complete 2
zfcp_fsf_request_timeout_handler
del_timer 2
fsf_req = from_timer(fsf_req, t, timer)
zfcp_fsf_req_free 2
adapter = fsf_req->adapter
^^^^^^^ already freed
Link: https://lore.kernel.org/r/20200813152856.50088-1-maier@linux.ibm.com
Fixes: 75492a5156 ("s390/scsi: Convert timers to use timer_setup()")
Cc: <stable@vger.kernel.org> #4.15+
Suggested-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Steffen Maier <maier@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7303cb5bfe upstream.
ext4_search_dir() and ext4_generic_delete_entry() can be called both for
standard director blocks and for inline directories stored inside inode
or inline xattr space. For the second case we didn't call
ext4_check_dir_entry() with proper constraints that could result in
accepting corrupted directory entry as well as false positive filesystem
errors like:
EXT4-fs error (device dm-0): ext4_search_dir:1395: inode #28320400:
block 113246792: comm dockerd: bad entry in directory: directory entry too
close to block end - offset=0, inode=28320403, rec_len=32, name_len=8,
size=4096
Fix the arguments passed to ext4_check_dir_entry().
Fixes: 109ba779d6 ("ext4: check for directory entries too close to block end")
CC: stable@vger.kernel.org
Signed-off-by: Jan Kara <jack@suse.cz>
Link: https://lore.kernel.org/r/20200731162135.8080-1-jack@suse.cz
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 88e8ac11d2 upstream.
The following race is observed with the repeated online, offline and a
delay between two successive online of memory blocks of movable zone.
P1 P2
Online the first memory block in
the movable zone. The pcp struct
values are initialized to default
values,i.e., pcp->high = 0 &
pcp->batch = 1.
Allocate the pages from the
movable zone.
Try to Online the second memory
block in the movable zone thus it
entered the online_pages() but yet
to call zone_pcp_update().
This process is entered into
the exit path thus it tries
to release the order-0 pages
to pcp lists through
free_unref_page_commit().
As pcp->high = 0, pcp->count = 1
proceed to call the function
free_pcppages_bulk().
Update the pcp values thus the
new pcp values are like, say,
pcp->high = 378, pcp->batch = 63.
Read the pcp's batch value using
READ_ONCE() and pass the same to
free_pcppages_bulk(), pcp values
passed here are, batch = 63,
count = 1.
Since num of pages in the pcp
lists are less than ->batch,
then it will stuck in
while(list_empty(list)) loop
with interrupts disabled thus
a core hung.
Avoid this by ensuring free_pcppages_bulk() is called with proper count of
pcp list pages.
The mentioned race is some what easily reproducible without [1] because
pcp's are not updated for the first memory block online and thus there is
a enough race window for P2 between alloc+free and pcp struct values
update through onlining of second memory block.
With [1], the race still exists but it is very narrow as we update the pcp
struct values for the first memory block online itself.
This is not limited to the movable zone, it could also happen in cases
with the normal zone (e.g., hotplug to a node that only has DMA memory, or
no other memory yet).
[1]: https://patchwork.kernel.org/patch/11696389/
Fixes: 5f8dcc2121 ("page-allocator: split per-cpu list into one-list-per-migrate-type")
Signed-off-by: Charan Teja Reddy <charante@codeaurora.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: David Hildenbrand <david@redhat.com>
Acked-by: David Rientjes <rientjes@google.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Vinayak Menon <vinmenon@codeaurora.org>
Cc: <stable@vger.kernel.org> [2.6+]
Link: http://lkml.kernel.org/r/1597150703-19003-1-git-send-email-charante@codeaurora.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e08d3fdfe2 upstream.
The lowmem_reserve arrays provide a means of applying pressure against
allocations from lower zones that were targeted at higher zones. Its
values are a function of the number of pages managed by higher zones and
are assigned by a call to the setup_per_zone_lowmem_reserve() function.
The function is initially called at boot time by the function
init_per_zone_wmark_min() and may be called later by accesses of the
/proc/sys/vm/lowmem_reserve_ratio sysctl file.
The function init_per_zone_wmark_min() was moved up from a module_init to
a core_initcall to resolve a sequencing issue with khugepaged.
Unfortunately this created a sequencing issue with CMA page accounting.
The CMA pages are added to the managed page count of a zone when
cma_init_reserved_areas() is called at boot also as a core_initcall. This
makes it uncertain whether the CMA pages will be added to the managed page
counts of their zones before or after the call to
init_per_zone_wmark_min() as it becomes dependent on link order. With the
current link order the pages are added to the managed count after the
lowmem_reserve arrays are initialized at boot.
This means the lowmem_reserve values at boot may be lower than the values
used later if /proc/sys/vm/lowmem_reserve_ratio is accessed even if the
ratio values are unchanged.
In many cases the difference is not significant, but for example
an ARM platform with 1GB of memory and the following memory layout
cma: Reserved 256 MiB at 0x0000000030000000
Zone ranges:
DMA [mem 0x0000000000000000-0x000000002fffffff]
Normal empty
HighMem [mem 0x0000000030000000-0x000000003fffffff]
would result in 0 lowmem_reserve for the DMA zone. This would allow
userspace to deplete the DMA zone easily.
Funnily enough
$ cat /proc/sys/vm/lowmem_reserve_ratio
would fix up the situation because as a side effect it forces
setup_per_zone_lowmem_reserve.
This commit breaks the link order dependency by invoking
init_per_zone_wmark_min() as a postcore_initcall so that the CMA pages
have the chance to be properly accounted in their zone(s) and allowing
the lowmem_reserve arrays to receive consistent values.
Fixes: bc22af74f2 ("mm: update min_free_kbytes from khugepaged after core initialization")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Jason Baron <jbaron@akamai.com>
Cc: David Rientjes <rientjes@google.com>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: <stable@vger.kernel.org>
Link: http://lkml.kernel.org/r/1597423766-27849-1-git-send-email-opendmb@gmail.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bcf85fcedf upstream.
romfs has a superblock field that limits the size of the filesystem; data
beyond that limit is never accessed.
romfs_dev_read() fetches a caller-supplied number of bytes from the
backing device. It returns 0 on success or an error code on failure;
therefore, its API can't represent short reads, it's all-or-nothing.
However, when romfs_dev_read() detects that the requested operation would
cross the filesystem size limit, it currently silently truncates the
requested number of bytes. This e.g. means that when the content of a
file with size 0x1000 starts one byte before the filesystem size limit,
->readpage() will only fill a single byte of the supplied page while
leaving the rest uninitialized, leaking that uninitialized memory to
userspace.
Fix it by returning an error code instead of truncating the read when the
requested read operation would go beyond the end of the filesystem.
Fixes: da4458bda2 ("NOMMU: Make it possible for RomFS to use MTD devices directly")
Signed-off-by: Jann Horn <jannh@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: David Howells <dhowells@redhat.com>
Cc: <stable@vger.kernel.org>
Link: http://lkml.kernel.org/r/20200818013202.2246365-1-jannh@google.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1e6e238c30 ]
[BUG]
There is a bug report of NULL pointer dereference caused in
compress_file_extent():
Oops: Kernel access of bad area, sig: 11 [#1]
LE PAGE_SIZE=64K MMU=Hash SMP NR_CPUS=2048 NUMA pSeries
Workqueue: btrfs-delalloc btrfs_delalloc_helper [btrfs]
NIP [c008000006dd4d34] compress_file_range.constprop.41+0x75c/0x8a0 [btrfs]
LR [c008000006dd4d1c] compress_file_range.constprop.41+0x744/0x8a0 [btrfs]
Call Trace:
[c000000c69093b00] [c008000006dd4d1c] compress_file_range.constprop.41+0x744/0x8a0 [btrfs] (unreliable)
[c000000c69093bd0] [c008000006dd4ebc] async_cow_start+0x44/0xa0 [btrfs]
[c000000c69093c10] [c008000006e14824] normal_work_helper+0xdc/0x598 [btrfs]
[c000000c69093c80] [c0000000001608c0] process_one_work+0x2c0/0x5b0
[c000000c69093d10] [c000000000160c38] worker_thread+0x88/0x660
[c000000c69093db0] [c00000000016b55c] kthread+0x1ac/0x1c0
[c000000c69093e20] [c00000000000b660] ret_from_kernel_thread+0x5c/0x7c
---[ end trace f16954aa20d822f6 ]---
[CAUSE]
For the following execution route of compress_file_range(), it's
possible to hit NULL pointer dereference:
compress_file_extent()
|- pages = NULL;
|- start = async_chunk->start = 0;
|- end = async_chunk = 4095;
|- nr_pages = 1;
|- inode_need_compress() == false; <<< Possible, see later explanation
| Now, we have nr_pages = 1, pages = NULL
|- cont:
|- ret = cow_file_range_inline();
|- if (ret <= 0) {
|- for (i = 0; i < nr_pages; i++) {
|- WARN_ON(pages[i]->mapping); <<< Crash
To enter above call execution branch, we need the following race:
Thread 1 (chattr) | Thread 2 (writeback)
--------------------------+------------------------------
| btrfs_run_delalloc_range
| |- inode_need_compress = true
| |- cow_file_range_async()
btrfs_ioctl_set_flag() |
|- binode_flags |= |
BTRFS_INODE_NOCOMPRESS |
| compress_file_range()
| |- inode_need_compress = false
| |- nr_page = 1 while pages = NULL
| | Then hit the crash
[FIX]
This patch will fix it by checking @pages before doing accessing it.
This patch is only designed as a hot fix and easy to backport.
More elegant fix may make btrfs only check inode_need_compress() once to
avoid such race, but that would be another story.
Reported-by: Luciano Chavez <chavez@us.ibm.com>
Fixes: 4d3a800ebb ("btrfs: merge nr_pages input and output parameter in compress_pages")
CC: stable@vger.kernel.org # 4.14.x: cecc8d9038: btrfs: Move free_pages_out label in inline extent handling branch in compress_file_range
CC: stable@vger.kernel.org # 4.14+
Signed-off-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cecc8d9038 ]
This label is only executed if compress_file_range fails to create an
inline extent. So move its code in the semantically related inline
extent handling branch. No functional changes.
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3ef3959b29 ]
Chris Murphy reported a problem where rpm ostree will bind mount a bunch
of things for whatever voodoo it's doing. But when it does this
/proc/mounts shows something like
/dev/sda /mnt/test btrfs rw,relatime,subvolid=256,subvol=/foo 0 0
/dev/sda /mnt/test/baz btrfs rw,relatime,subvolid=256,subvol=/foo/bar 0 0
Despite subvolid=256 being subvol=/foo. This is because we're just
spitting out the dentry of the mount point, which in the case of bind
mounts is the source path for the mountpoint. Instead we should spit
out the path to the actual subvol. Fix this by looking up the name for
the subvolid we have mounted. With this fix the same test looks like
this
/dev/sda /mnt/test btrfs rw,relatime,subvolid=256,subvol=/foo 0 0
/dev/sda /mnt/test/baz btrfs rw,relatime,subvolid=256,subvol=/foo 0 0
Reported-by: Chris Murphy <chris@colorremedies.com>
CC: stable@vger.kernel.org # 4.4+
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c0c907a47d ]
The functions will be used outside of export.c and super.c to allow
resolving subvolume name from a given id, eg. for subvolume deletion by
id ioctl.
Signed-off-by: Marcos Paulo de Souza <mpdesouza@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
[ split from the next patch ]
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bbe98f9cad ]
Move collapse_huge_page()'s mmget_still_valid() check into
khugepaged_test_exit() itself. collapse_huge_page() is used for anon THP
only, and earned its mmget_still_valid() check because it inserts a huge
pmd entry in place of the page table's pmd entry; whereas
collapse_file()'s retract_page_tables() or collapse_pte_mapped_thp()
merely clears the page table's pmd entry. But core dumping without mmap
lock must have been as open to mistaking a racily cleared pmd entry for a
page table at physical page 0, as exit_mmap() was. And we certainly have
no interest in mapping as a THP once dumping core.
Fixes: 59ea6d06cf ("coredump: fix race condition between collapse_huge_page() and core dumping")
Signed-off-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Song Liu <songliubraving@fb.com>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: <stable@vger.kernel.org> [4.8+]
Link: http://lkml.kernel.org/r/alpine.LSU.2.11.2008021217020.27773@eggly.anvils
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 12d572e785 ]
Fix the memory leakage in debuginfo__find_trace_events() when the probe
point is not found in the debuginfo. If there is no probe point found in
the debuginfo, debuginfo__find_probes() will NOT return -ENOENT, but 0.
Thus the caller of debuginfo__find_probes() must check the tf.ntevs and
release the allocated memory for the array of struct probe_trace_event.
The current code releases the memory only if the debuginfo__find_probes()
hits an error but not checks tf.ntevs. In the result, the memory allocated
on *tevs are not released if tf.ntevs == 0.
This fixes the memory leakage by checking tf.ntevs == 0 in addition to
ret < 0.
Fixes: ff74178350 ("perf probe: Introduce debuginfo to encapsulate dwarf information")
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Reviewed-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: stable@vger.kernel.org
Link: http://lore.kernel.org/lkml/159438668346.62703.10887420400718492503.stgit@devnote2
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 119c53d2d4 ]
drm_gem_dumb_map_offset() now exists and does everything
vgem_gem_dump_map does and *ought* to do.
In particular, vgem_gem_dumb_map() was trying to reject mmapping an
imported dmabuf by checking the existence of obj->filp. Unfortunately,
we always allocated an obj->filp, even if unused for an imported dmabuf.
Instead, the drm_gem_dumb_map_offset(), since commit 90378e5891
("drm/gem: drm_gem_dumb_map_offset(): reject dma-buf"), uses the
obj->import_attach to reject such invalid mmaps.
This prevents vgem from allowing userspace mmapping the dumb handle and
attempting to incorrectly fault in remote pages belonging to another
device, where there may not even be a struct page.
v2: Use the default drm_gem_dumb_map_offset() callback
Fixes: af33a9190d ("drm/vgem: Enable dmabuf import interfaces")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: <stable@vger.kernel.org> # v4.13+
Link: https://patchwork.freedesktop.org/patch/msgid/20200708154911.21236-1-chris@chris-wilson.co.uk
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit f878122841 upstream.
Reproducing bug report here:
After hibernating and resuming, DPM is not enabled. This remains the case
even if you test hibernate using the steps here:
https://www.kernel.org/doc/html/latest/power/basic-pm-debugging.html
I debugged the problem, and figured out that in the file hardwaremanager.c,
in the function, phm_enable_dynamic_state_management(), the check
'if (!hwmgr->pp_one_vf && smum_is_dpm_running(hwmgr) && !amdgpu_passthrough(adev) && adev->in_suspend)'
returns true for the hibernate case, and false for the suspend case.
This means that for the hibernate case, the AMDGPU driver doesn't enable DPM
(even though it should) and simply returns from that function.
In the suspend case, it goes ahead and enables DPM, even though it doesn't need to.
I debugged further, and found out that in the case of suspend, for the
CIK/Hawaii GPUs, smum_is_dpm_running(hwmgr) returns false, while in the case of
hibernate, smum_is_dpm_running(hwmgr) returns true.
For CIK, the ci_is_dpm_running() function calls the ci_is_smc_ram_running() function,
which is ultimately used to determine if DPM is currently enabled or not,
and this seems to provide the wrong answer.
I've changed the ci_is_dpm_running() function to instead use the same method that
some other AMD GPU chips do (e.g Fiji), which seems to read the voltage controller.
I've tested on my R9 390 and it seems to work correctly for both suspend and
hibernate use cases, and has been stable so far.
Bug: https://bugzilla.kernel.org/show_bug.cgi?id=208839
Signed-off-by: Sandeep Raghuraman <sandy.8925@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5253cb8c00 upstream.
The maker of this board and its variants, stores MAC address in U-Boot
environment. Add alias for bootloader to recognise, to which ethernet
node inject the factory MAC address.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
[pali: Backported to 5.4 and older versions]
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 18e77600f7 upstream.
Only once have I seen this scenario (and forgot even to notice what forced
the eventual crash): a sequence of "BUG: Bad page map" alerts from
vm_normal_page(), from zap_pte_range() servicing exit_mmap();
pmd:00000000, pte values corresponding to data in physical page 0.
The pte mappings being zapped in this case were supposed to be from a huge
page of ext4 text (but could as well have been shmem): my belief is that
it was racing with collapse_file()'s retract_page_tables(), found *pmd
pointing to a page table, locked it, but *pmd had become 0 by the time
start_pte was decided.
In most cases, that possibility is excluded by holding mmap lock; but
exit_mmap() proceeds without mmap lock. Most of what's run by khugepaged
checks khugepaged_test_exit() after acquiring mmap lock:
khugepaged_collapse_pte_mapped_thps() and hugepage_vma_revalidate() do so,
for example. But retract_page_tables() did not: fix that.
The fix is for retract_page_tables() to check khugepaged_test_exit(),
after acquiring mmap lock, before doing anything to the page table.
Getting the mmap lock serializes with __mmput(), which briefly takes and
drops it in __khugepaged_exit(); then the khugepaged_test_exit() check on
mm_users makes sure we don't touch the page table once exit_mmap() might
reach it, since exit_mmap() will be proceeding without mmap lock, not
expecting anyone to be racing with it.
Fixes: f3f0e1d215 ("khugepaged: add support of collapse for tmpfs/shmem pages")
Signed-off-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Song Liu <songliubraving@fb.com>
Cc: <stable@vger.kernel.org> [4.8+]
Link: http://lkml.kernel.org/r/alpine.LSU.2.11.2008021215400.27773@eggly.anvils
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0c64a0dce5 ]
The Landisk setup code maps the CF IDE area using ioremap_prot(), and
passes the resulting virtual addresses to the pata_platform driver,
disguising them as I/O port addresses. Hence the pata_platform driver
translates them again using ioport_map().
As CONFIG_GENERIC_IOMAP=n, and CONFIG_HAS_IOPORT_MAP=y, the
SuperH-specific mapping code in arch/sh/kernel/ioport.c translates
I/O port addresses to virtual addresses by adding sh_io_port_base, which
defaults to -1, thus breaking the assumption of an identity mapping.
Fix this by setting sh_io_port_base to zero.
Fixes: 37b7a97884 ("sh: machvec IO death.")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Rich Felker <dalias@libc.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fa5c893181 ]
When using a cross-compilation environment, such as OpenEmbedded,
the CC an CXX variables are set to something more than just a
command: there are arguments (such as --sysroot) that need to be
passed on to the compiler so that the right set of headers and
libraries are used.
For the particular case that our systems detected, CC is set to
the following:
export CC="aarch64-linaro-linux-gcc --sysroot=/oe/build/tmp/work/machine/perf/1.0-r9/recipe-sysroot"
Without quotes, detection is as follows:
Auto-detecting system features:
... dwarf: [ OFF ]
... dwarf_getlocations: [ OFF ]
... glibc: [ OFF ]
... gtk2: [ OFF ]
... libbfd: [ OFF ]
... libcap: [ OFF ]
... libelf: [ OFF ]
... libnuma: [ OFF ]
... numa_num_possible_cpus: [ OFF ]
... libperl: [ OFF ]
... libpython: [ OFF ]
... libcrypto: [ OFF ]
... libunwind: [ OFF ]
... libdw-dwarf-unwind: [ OFF ]
... zlib: [ OFF ]
... lzma: [ OFF ]
... get_cpuid: [ OFF ]
... bpf: [ OFF ]
... libaio: [ OFF ]
... libzstd: [ OFF ]
... disassembler-four-args: [ OFF ]
Makefile.config:414: *** No gnu/libc-version.h found, please install glibc-dev[el]. Stop.
Makefile.perf:230: recipe for target 'sub-make' failed
make[1]: *** [sub-make] Error 2
Makefile:69: recipe for target 'all' failed
make: *** [all] Error 2
With CC and CXX quoted, some of those features are now detected.
Fixes: e3232c2f39 ("tools build feature: Use CC and CXX from parent")
Signed-off-by: Daniel Díaz <daniel.diaz@linaro.org>
Reviewed-by: Thomas Hebb <tommyhebb@gmail.com>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Andrii Nakryiko <andriin@fb.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: John Fastabend <john.fastabend@gmail.com>
Cc: KP Singh <kpsingh@chromium.org>
Cc: Martin KaFai Lau <kafai@fb.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Song Liu <songliubraving@fb.com>
Cc: Stephane Eranian <eranian@google.com>
Cc: Yonghong Song <yhs@fb.com>
Link: http://lore.kernel.org/lkml/20200812221518.2869003-1-daniel.diaz@linaro.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1beaef29c3 ]
For memcpy, the source pages are memset to zero only when --cycles is
used. This leads to wildly different results with or without --cycles,
since all sources pages are likely to be mapped to the same zero page
without explicit writes.
Before this fix:
$ export cmd="./perf stat -e LLC-loads -- ./perf bench \
mem memcpy -s 1024MB -l 100 -f default"
$ $cmd
2,935,826 LLC-loads
3.821677452 seconds time elapsed
$ $cmd --cycles
217,533,436 LLC-loads
8.616725985 seconds time elapsed
After this fix:
$ $cmd
214,459,686 LLC-loads
8.674301124 seconds time elapsed
$ $cmd --cycles
214,758,651 LLC-loads
8.644480006 seconds time elapsed
Fixes: 47b5757bac ("perf bench mem: Move boilerplate memory allocation to the infrastructure")
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: kernel@axis.com
Link: http://lore.kernel.org/lkml/20200810133404.30829-1-vincent.whitchurch@axis.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
