[ Upstream commit a268e0f245 ]
proc_fs was used, in af_packet, without a surrounding #ifdef,
although there is no hard dependency on proc_fs.
That caused the initialization of the af_packet module to fail
when CONFIG_PROC_FS=n.
Specifically, proc_create_net() was used in af_packet.c,
and when it fails, packet_net_init() returns -ENOMEM.
It will always fail when the kernel is compiled without proc_fs,
because, proc_create_net() for example always returns NULL.
The calling order that starts in af_packet.c is as follows:
packet_init()
register_pernet_subsys()
register_pernet_operations()
__register_pernet_operations()
ops_init()
ops->init() (packet_net_ops.init=packet_net_init())
proc_create_net()
It worked in the past because register_pernet_subsys()'s return value
wasn't checked before this Commit 36096f2f4f ("packet: Fix error path in
packet_init.").
It always returned an error, but was not checked before, so everything
was working even when CONFIG_PROC_FS=n.
The fix here is simply to add the necessary #ifdef.
This also fixes a similar error in tls_proc.c, that was found by Jakub
Kicinski.
Fixes: d26b698dd3 ("net/tls: add skeleton of MIB statistics")
Fixes: 36096f2f4f ("packet: Fix error path in packet_init")
Signed-off-by: Yonatan Linik <yonatanlinik@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aadaca9e7c ]
The mru in the qdisc_skb_cb should be init as 0. Only defrag packets in the
act_ct will set the value.
Fixes: 038ebb1a71 ("net/sched: act_ct: fix miss set mru for ovs after defrag in act_ct")
Signed-off-by: wenxu <wenxu@ucloud.cn>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 860975c6f8 ]
In case a subflow path is blocked, MPTCP-level retransmit may not take
place anymore because such subflow is likely to have unacked data left
in its write queue.
Ignore subflows that have experienced loss and test next candidate.
Fixes: 3b1d6210a9 ("mptcp: implement and use MPTCP-level retransmission")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ae068f561b ]
The port ID for control messages was uncorrectly set with broadcast
node ID value, causing message to be dropped on remote side since
not passing packet filtering (cb->dst_port != QRTR_PORT_CTRL).
Fixes: d27e77a3de ("net: qrtr: Reset the node and port ID of broadcast messages")
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dae7a75f1f ]
Currently, iser target support max IO size of 16MiB by default. For some
adapters, allocating this amount of resources might reduce the total
number of possible connections that can be created. For those adapters,
it's preferred to reduce the max IO size to be able to create more
connections. Since there is no handshake procedure for max IO size in iser
protocol, set the default max IO size to 1MiB and add a module parameter
for enabling the option to control it for suitable adapters.
Fixes: 317000b926 ("IB/isert: allocate RW ctxs according to max IO size")
Link: https://lore.kernel.org/r/20201019094628.17202-1-mgurtovoy@nvidia.com
Reported-by: Krishnamraju Eraparaju <krishna2@chelsio.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Max Gurtovoy <mgurtovoy@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 65b709586e upstream.
The get_config callback can be used by the device to fill the
config structure.
The callback will be invoked in vdpasim_get_config() before copying
bytes into caller buffer.
Move vDPA-net config updates from vdpasim_set_features() in the
new vdpasim_net_get_config() callback.
This is safe since in vdpa_get_config() we already check that
.set_features() callback is called before .get_config().
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Link: https://lore.kernel.org/r/20201215144256.155342-13-sgarzare@redhat.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit aee9ddb1d3 upstream.
Currently there's a KCOV remote coverage collection section in
__usb_hcd_giveback_urb(). Initially that section was added based on the
assumption that usb_hcd_giveback_urb() can only be called in interrupt
context as indicated by a comment before it. This is what happens when
syzkaller is fuzzing the USB stack via the dummy_hcd driver.
As it turns out, it's actually valid to call usb_hcd_giveback_urb() in task
context, provided that the caller turned off the interrupts; USB/IP does
exactly that. This can lead to a nested KCOV remote coverage collection
sections both trying to collect coverage in task context. This isn't
supported by KCOV, and leads to a WARNING.
Change __usb_hcd_giveback_urb() to only call kcov_remote_*() callbacks
when it's being executed in a softirq. As the result, the coverage from
USB/IP related usb_hcd_giveback_urb() calls won't be collected, but the
WARNING is fixed.
A potential future improvement would be to support nested remote coverage
collection sections, but this patch doesn't address that.
Reviewed-by: Dmitry Vyukov <dvyukov@google.com>
Acked-by: Marco Elver <elver@google.com>
Signed-off-by: Andrey Konovalov <andreyknvl@google.com>
Link: https://lore.kernel.org/r/f3a7a153f0719cb53ec385b16e912798bd3e4cf9.1602856358.git.andreyknvl@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a11148e6fc upstream.
syzbot found WARNING in rds_rdma_extra_size [1] when RDS_CMSG_RDMA_ARGS
control message is passed with user-controlled
0x40001 bytes of args->nr_local, causing order >= MAX_ORDER condition.
The exact value 0x40001 can be checked with UIO_MAXIOV which is 0x400.
So for kcalloc() 0x400 iovecs with sizeof(struct rds_iovec) = 0x10
is the closest limit, with 0x10 leftover.
Same condition is currently done in rds_cmsg_rdma_args().
[1] WARNING: mm/page_alloc.c:5011
[..]
Call Trace:
alloc_pages_current+0x18c/0x2a0 mm/mempolicy.c:2267
alloc_pages include/linux/gfp.h:547 [inline]
kmalloc_order+0x2e/0xb0 mm/slab_common.c:837
kmalloc_order_trace+0x14/0x120 mm/slab_common.c:853
kmalloc_array include/linux/slab.h:592 [inline]
kcalloc include/linux/slab.h:621 [inline]
rds_rdma_extra_size+0xb2/0x3b0 net/rds/rdma.c:568
rds_rm_size net/rds/send.c:928 [inline]
Reported-by: syzbot+1bd2b07f93745fa38425@syzkaller.appspotmail.com
Signed-off-by: Sabyrzhan Tasbolatov <snovitoll@gmail.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Link: https://lore.kernel.org/r/20210201203233.1324704-1-snovitoll@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1c5fae9c9a upstream.
In vsock_shutdown() we touched some socket fields without holding the
socket lock, such as 'state' and 'sk_flags'.
Also, after the introduction of multi-transport, we are accessing
'vsk->transport' in vsock_send_shutdown() without holding the lock
and this call can be made while the connection is in progress, so
the transport can change in the meantime.
To avoid issues, we hold the socket lock when we enter in
vsock_shutdown() and release it when we leave.
Among the transports that implement the 'shutdown' callback, only
hyperv_transport acquired the lock. Since the caller now holds it,
we no longer take it.
Fixes: d021c34405 ("VSOCK: Introduce VM Sockets")
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ce7536bc73 upstream.
If the socket is closed or is being released, some resources used by
virtio_transport_space_update() such as 'vsk->trans' may be released.
To avoid a use after free bug we should only update the available credit
when we are sure the socket is still open and we have the lock held.
Fixes: 06a8fc7836 ("VSOCK: Introduce virtio_vsock_common.ko")
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Link: https://lore.kernel.org/r/20210208144454.84438-1-sgarzare@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 059d2a1004 upstream.
Now that MRP started to use also SWITCHDEV_ATTR_ID_PORT_STP_STATE to
notify HW, then SWITCHDEV_ATTR_ID_MRP_PORT_STAT is not used anywhere
else, therefore we can remove it.
Fixes: c284b54590 ("switchdev: mrp: Extend switchdev API to offload MRP")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b2bdba1cbc upstream.
The function br_mrp_port_switchdev_set_state was called both with MRP
port state and STP port state, which is an issue because they don't
match exactly.
Therefore, update the function to be used only with STP port state and
use the id SWITCHDEV_ATTR_ID_PORT_STP_STATE.
The choice of using STP over MRP is that the drivers already implement
SWITCHDEV_ATTR_ID_PORT_STP_STATE and already in SW we update the port
STP state.
Fixes: 9a9f26e8f7 ("bridge: mrp: Connect MRP API with the switchdev API")
Fixes: fadd409136 ("bridge: switchdev: mrp: Implement MRP API for switchdev")
Fixes: 2f1a11ae11 ("bridge: mrp: Add MRP interface.")
Reported-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3aa6bce9af upstream.
Prevent netif_tx_disable() running concurrently with dev_watchdog() by
taking the device global xmit lock. Otherwise, the recommended:
netif_carrier_off(dev);
netif_tx_disable(dev);
driver shutdown sequence can happen after the watchdog has already
checked carrier, resulting in possible false alarms. This is because
netif_tx_lock() only sets the frozen bit without maintaining the locks
on the individual queues.
Fixes: c3f26a269c ("netdev: Fix lockdep warnings in multiqueue configurations.")
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5d1cbcc990 upstream.
In vsock_stream_connect(), a thread will enter schedule_timeout().
While being scheduled out, another thread can enter vsock_stream_connect()
as well and set vsk->transport to NULL. In case a signal was sent, the
first thread can leave schedule_timeout() and vsock_transport_cancel_pkt()
will be called right after. Inside vsock_transport_cancel_pkt(), a null
dereference will happen on transport->cancel_pkt.
Fixes: c0cfa2d8a7 ("vsock: add multi-transports support")
Signed-off-by: Norbert Slusarek <nslusarek@gmx.net>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Link: https://lore.kernel.org/r/trinity-c2d6cede-bfb1-44e2-85af-1fbc7f541715-1612535117028@3c-app-gmx-bap12
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit af8085f3a4 upstream.
The sctp transport seq_file iterators take a reference to the transport
in the ->start and ->next functions and releases the reference in the
->show function. The preferred handling for such resources is to
release them in the subsequent ->next or ->stop function call.
Since Commit 1f4aace60b ("fs/seq_file.c: simplify seq_file iteration
code and interface") there is no guarantee that ->show will be called
after ->next, so this function can now leak references.
So move the sctp_transport_put() call to ->next and ->stop.
Fixes: 1f4aace60b ("fs/seq_file.c: simplify seq_file iteration code and interface")
Reported-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d11a1d08a0 upstream.
If the maximum performance level taken for computing the
arch_max_freq_ratio value used in the x86 scale-invariance code is
higher than the one corresponding to the cpuinfo.max_freq value
coming from the acpi_cpufreq driver, the scale-invariant utilization
falls below 100% even if the CPU runs at cpuinfo.max_freq or slightly
faster, which causes the schedutil governor to select a frequency
below cpuinfo.max_freq. That frequency corresponds to a frequency
table entry below the maximum performance level necessary to get to
the "boost" range of CPU frequencies which prevents "boost"
frequencies from being used in some workloads.
While this issue is related to scale-invariance, it may be amplified
by commit db865272d9 ("cpufreq: Avoid configuring old governors as
default with intel_pstate") from the 5.10 development cycle which
made it extremely easy to default to schedutil even if the preferred
driver is acpi_cpufreq as long as intel_pstate is built too, because
the mere presence of the latter effectively removes the ondemand
governor from the defaults. Distro kernels are likely to include
both intel_pstate and acpi_cpufreq on x86, so their users who cannot
use intel_pstate or choose to use acpi_cpufreq may easily be
affectecd by this issue.
If CPPC is available, it can be used to address this issue by
extending the frequency tables created by acpi_cpufreq to cover the
entire available frequency range (including "boost" frequencies) for
each CPU, but if CPPC is not there, acpi_cpufreq has no idea what
the maximum "boost" frequency is and the frequency tables created by
it cannot be extended in a meaningful way, so in that case make it
ask the arch scale-invariance code to to use the "nominal" performance
level for CPU utilization scaling in order to avoid the issue at hand.
Fixes: db865272d9 ("cpufreq: Avoid configuring old governors as default with intel_pstate")
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Giovanni Gherdovich <ggherdovich@suse.cz>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3c55e94c0a upstream.
A severe performance regression on AMD EPYC processors when using
the schedutil scaling governor was discovered by Phoronix.com and
attributed to the following commits:
41ea667227 ("x86, sched: Calculate frequency invariance for AMD
systems")
976df7e573 ("x86, sched: Use midpoint of max_boost and max_P for
frequency invariance on AMD EPYC")
The source of the problem is that the maximum performance level taken
for computing the arch_max_freq_ratio value used in the x86 scale-
invariance code is higher than the one corresponding to the
cpuinfo.max_freq value coming from the acpi_cpufreq driver.
This effectively causes the scale-invariant utilization to fall below
100% even if the CPU runs at cpuinfo.max_freq or slightly faster, so
the schedutil governor selects a frequency below cpuinfo.max_freq
then. That frequency corresponds to a frequency table entry below
the maximum performance level necessary to get to the "boost" range
of CPU frequencies.
However, if the cpuinfo.max_freq value coming from acpi_cpufreq was
higher, the schedutil governor would select higher frequencies which
in turn would allow acpi_cpufreq to set more adequate performance
levels and to get to the "boost" range of CPU frequencies more often.
This issue affects any systems where acpi_cpufreq is used and the
"boost" (or "turbo") frequencies are enabled, not just AMD EPYC.
Moreover, commit db865272d9 ("cpufreq: Avoid configuring old
governors as default with intel_pstate") from the 5.10 development
cycle made it extremely easy to default to schedutil even if the
preferred driver is acpi_cpufreq as long as intel_pstate is built
too, because the mere presence of the latter effectively removes the
ondemand governor from the defaults. Distro kernels are likely to
include both intel_pstate and acpi_cpufreq on x86, so their users
who cannot use intel_pstate or choose to use acpi_cpufreq may
easily be affectecd by this issue.
To address this issue, extend the frequency table constructed by
acpi_cpufreq for each CPU to cover the entire range of available
frequencies (including the "boost" ones) if CPPC is available and
indicates that "boost" (or "turbo") frequencies are enabled. That
causes cpuinfo.max_freq to become the maximum "boost" frequency of
the given CPU (instead of the maximum frequency returned by the ACPI
_PSS object that corresponds to the "nominal" performance level).
Fixes: 41ea667227 ("x86, sched: Calculate frequency invariance for AMD systems")
Fixes: 976df7e573 ("x86, sched: Use midpoint of max_boost and max_P for frequency invariance on AMD EPYC")
Fixes: db865272d9 ("cpufreq: Avoid configuring old governors as default with intel_pstate")
Link: https://www.phoronix.com/scan.php?page=article&item=linux511-amd-schedutil&num=1
Link: https://lore.kernel.org/linux-pm/20210203135321.12253-2-ggherdovich@suse.cz/
Reported-by: Michael Larabel <Michael@phoronix.com>
Diagnosed-by: Giovanni Gherdovich <ggherdovich@suse.cz>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Giovanni Gherdovich <ggherdovich@suse.cz>
Reviewed-by: Giovanni Gherdovich <ggherdovich@suse.cz>
Tested-by: Michael Larabel <Michael@phoronix.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7b5eab57ca upstream.
At the end of rxrpc_release_call(), rxrpc_cleanup_ring() is called to clear
the Rx/Tx skbuff ring, but this doesn't lock the ring whilst it's accessing
it. Unfortunately, rxrpc_resend() might be trying to retransmit a packet
concurrently with this - and whilst it does lock the ring, this isn't
protection against rxrpc_cleanup_call().
Fix this by removing the call to rxrpc_cleanup_ring() from
rxrpc_release_call(). rxrpc_cleanup_ring() will be called again anyway
from rxrpc_cleanup_call(). The earlier call is just an optimisation to
recycle skbuffs more quickly.
Alternative solutions include rxrpc_release_call() could try to cancel the
work item or wait for it to complete or rxrpc_cleanup_ring() could lock
when accessing the ring (which would require a bh lock).
This can produce a report like the following:
BUG: KASAN: use-after-free in rxrpc_send_data_packet+0x19b4/0x1e70 net/rxrpc/output.c:372
Read of size 4 at addr ffff888011606e04 by task kworker/0:0/5
...
Workqueue: krxrpcd rxrpc_process_call
Call Trace:
...
kasan_report.cold+0x79/0xd5 mm/kasan/report.c:413
rxrpc_send_data_packet+0x19b4/0x1e70 net/rxrpc/output.c:372
rxrpc_resend net/rxrpc/call_event.c:266 [inline]
rxrpc_process_call+0x1634/0x1f60 net/rxrpc/call_event.c:412
process_one_work+0x98d/0x15f0 kernel/workqueue.c:2275
...
Allocated by task 2318:
...
sock_alloc_send_pskb+0x793/0x920 net/core/sock.c:2348
rxrpc_send_data+0xb51/0x2bf0 net/rxrpc/sendmsg.c:358
rxrpc_do_sendmsg+0xc03/0x1350 net/rxrpc/sendmsg.c:744
rxrpc_sendmsg+0x420/0x630 net/rxrpc/af_rxrpc.c:560
...
Freed by task 2318:
...
kfree_skb+0x140/0x3f0 net/core/skbuff.c:704
rxrpc_free_skb+0x11d/0x150 net/rxrpc/skbuff.c:78
rxrpc_cleanup_ring net/rxrpc/call_object.c:485 [inline]
rxrpc_release_call+0x5dd/0x860 net/rxrpc/call_object.c:552
rxrpc_release_calls_on_socket+0x21c/0x300 net/rxrpc/call_object.c:579
rxrpc_release_sock net/rxrpc/af_rxrpc.c:885 [inline]
rxrpc_release+0x263/0x5a0 net/rxrpc/af_rxrpc.c:916
__sock_release+0xcd/0x280 net/socket.c:597
...
The buggy address belongs to the object at ffff888011606dc0
which belongs to the cache skbuff_head_cache of size 232
Fixes: 248f219cb8 ("rxrpc: Rewrite the data and ack handling code")
Reported-by: syzbot+174de899852504e4a74a@syzkaller.appspotmail.com
Reported-by: syzbot+3d1c772efafd3c38d007@syzkaller.appspotmail.com
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Hillf Danton <hdanton@sina.com>
Link: https://lore.kernel.org/r/161234207610.653119.5287360098400436976.stgit@warthog.procyon.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 68d54ceeec upstream.
The ptrace(PTRACE_PEEKMTETAGS) implementation checks whether the user
page has valid tags (mapped with PROT_MTE) by testing the PG_mte_tagged
page flag. If this bit is cleared, ptrace(PTRACE_PEEKMTETAGS) returns
-EIO.
A newly created (PROT_MTE) mapping points to the zero page which had its
tags zeroed during cpu_enable_mte(). If there were no prior writes to
this mapping, ptrace(PTRACE_PEEKMTETAGS) fails with -EIO since the zero
page does not have the PG_mte_tagged flag set.
Set PG_mte_tagged on the zero page when its tags are cleared during
boot. In addition, to avoid ptrace(PTRACE_PEEKMTETAGS) succeeding on
!PROT_MTE mappings pointing to the zero page, change the
__access_remote_tags() check to (vm_flags & VM_MTE) instead of
PG_mte_tagged.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Fixes: 34bfeea4a9 ("arm64: mte: Clear the tags when a page is mapped in user-space with PROT_MTE")
Cc: <stable@vger.kernel.org> # 5.10.x
Cc: Will Deacon <will@kernel.org>
Reported-by: Luis Machado <luis.machado@linaro.org>
Tested-by: Luis Machado <luis.machado@linaro.org>
Reviewed-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Link: https://lore.kernel.org/r/20210210180316.23654-1-catalin.marinas@arm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 70245f86c1 upstream.
Invoking x86_init.irqs.create_pci_msi_domain() before
x86_init.pci.arch_init() breaks XEN PV.
The XEN_PV specific pci.arch_init() function overrides the default
create_pci_msi_domain() which is obviously too late.
As a consequence the XEN PV PCI/MSI allocation goes through the native
path which runs out of vectors and causes malfunction.
Invoke it after x86_init.pci.arch_init().
Fixes: 6b15ffa07d ("x86/irq: Initialize PCI/MSI domain at PCI init time")
Reported-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Juergen Gross <jgross@suse.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/87pn18djte.fsf@nanos.tec.linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3d6a3d3a2a ]
The digital filter related computation are present in the driver
however the programming of the filter within the IP is missing.
The maximum value for the DNF is wrong and should be 15 instead of 16.
Fixes: aeb068c572 ("i2c: i2c-stm32f7: add driver")
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Signed-off-by: Pierre-Yves MORDRET <pierre-yves.mordret@foss.st.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6a155216c4 ]
As it turns out, vendor HDMI PHY driver for H6 has a pretty big table
of predefined values for various pixel clocks. However, most of them are
not useful/tested because they come from reference driver code. Vendor
PHY driver is concerned with only few of those, namely 27 MHz, 74.25
MHz, 148.5 MHz, 297 MHz and 594 MHz. These are all frequencies for
standard CEA modes.
Fix sun50i_h6_cur_ctr and sun50i_h6_phy_config with the values only for
aforementioned frequencies.
Table sun50i_h6_mpll_cfg doesn't need to be changed because values are
actually frequency dependent and not so much SoC dependent. See i.MX6
documentation for explanation of those values for similar PHY.
Fixes: c71c9b2fee ("drm/sun4i: Add support for Synopsys HDMI PHY")
Tested-by: Andre Heider <a.heider@gmail.com>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20210209175900.7092-5-jernej.skrabec@siol.net
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 50791f5d7b ]
Channel 1 has polarity bits for vsync and hsync signals but driver never
sets them. It turns out that with pre-HDMI2 controllers seemingly there
is no issue if polarity is not set. However, with HDMI2 controllers
(H6) there often comes to de-synchronization due to phase shift. This
causes flickering screen. It's safe to assume that similar issues might
happen also with pre-HDMI2 controllers.
Solve issue with setting vsync and hsync polarity. Note that display
stacks with tcon top have polarity bits actually in tcon0 polarity
register.
Fixes: 9026e0d122 ("drm: Add Allwinner A10 Display Engine support")
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Tested-by: Andre Heider <a.heider@gmail.com>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20210209175900.7092-3-jernej.skrabec@siol.net
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 793f49a87a ]
arm64 references the start address of .builtin_fw (__start_builtin_fw)
with a pair of R_AARCH64_ADR_PREL_PG_HI21/R_AARCH64_LDST64_ABS_LO12_NC
relocations. The compiler is allowed to emit the
R_AARCH64_LDST64_ABS_LO12_NC relocation because struct builtin_fw in
include/linux/firmware.h is 8-byte aligned.
The R_AARCH64_LDST64_ABS_LO12_NC relocation requires the address to be a
multiple of 8, which may not be the case if .builtin_fw is empty.
Unconditionally align .builtin_fw to fix the linker error. 32-bit
architectures could use ALIGN(4) but that would add unnecessary
complexity, so just use ALIGN(8).
Link: https://lkml.kernel.org/r/20201208054646.2913063-1-maskray@google.com
Link: https://github.com/ClangBuiltLinux/linux/issues/1204
Fixes: 5658c76 ("firmware: allow firmware files to be built into kernel image")
Signed-off-by: Fangrui Song <maskray@google.com>
Reported-by: kernel test robot <lkp@intel.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Tested-by: Nick Desaulniers <ndesaulniers@google.com>
Tested-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 532cfc0df1 ]
The index is received from vf, if use it directly,
an out-of-bound issue may be caused, so add a check for
this index before using it in hclge_get_rss_key().
Fixes: a638b1d8cc ("net: hns3: fix get VF RSS issue")
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 326334aad0 ]
The tqp_index is received from vf, if use it directly,
an out-of-bound issue may be caused, so add a check for
this tqp_index before using it in hclge_get_ring_chain_from_mbx().
Fixes: 84e095d64e ("net: hns3: Change PF to add ring-vect binding & resetQ to mailbox")
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 67a69f84ca ]
The queue_id is received from vf, if use it directly,
an out-of-bound issue may be caused, so add a check for
this queue_id before using it in hclge_reset_vf_queue().
Fixes: 1a426f8b40 ("net: hns3: fix the VF queue reset flow error")
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eb4733d7cf ]
There are several issues which may be seen when the link goes down while
forwarding traffic, all of which can be attributed to the fact that the
port flushing procedure from the reference manual was not closely
followed.
With flow control enabled on both the ingress port and the egress port,
it may happen when a link goes down that Ethernet packets are in flight.
In flow control mode, frames are held back and not dropped. When there
is enough traffic in flight (example: iperf3 TCP), then the ingress port
might enter congestion and never exit that state. This is a problem,
because it is the egress port's link that went down, and that has caused
the inability of the ingress port to send packets to any other port.
This is solved by flushing the egress port's queues when it goes down.
There is also a problem when performing stream splitting for
IEEE 802.1CB traffic (not yet upstream, but a sort of multicast,
basically). There, if one port from the destination ports mask goes
down, splitting the stream towards the other destinations will no longer
be performed. This can be traced down to this line:
ocelot_port_writel(ocelot_port, 0, DEV_MAC_ENA_CFG);
which should have been instead, as per the reference manual:
ocelot_port_rmwl(ocelot_port, 0, DEV_MAC_ENA_CFG_RX_ENA,
DEV_MAC_ENA_CFG);
Basically only DEV_MAC_ENA_CFG_RX_ENA should be disabled, but not
DEV_MAC_ENA_CFG_TX_ENA - I don't have further insight into why that is
the case, but apparently multicasting to several ports will cause issues
if at least one of them doesn't have DEV_MAC_ENA_CFG_TX_ENA set.
I am not sure what the state of the Ocelot VSC7514 driver is, but
probably not as bad as Felix/Seville, since VSC7514 uses phylib and has
the following in ocelot_adjust_link:
if (!phydev->link)
return;
therefore the port is not really put down when the link is lost, unlike
the DSA drivers which use .phylink_mac_link_down for that.
Nonetheless, I put ocelot_port_flush() in the common ocelot.c because it
needs to access some registers from drivers/net/ethernet/mscc/ocelot_rew.h
which are not exported in include/soc/mscc/ and a bugfix patch should
probably not move headers around.
Fixes: bdeced75b1 ("net: dsa: felix: Add PCS operations for PHYLINK")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
