commit 3c398f3c3b upstream.
after unbinding mmc I get things like this:
[ 185.294067] mmc1: card 0001 removed
[ 185.305206] omap_hsmmc 480b4000.mmc: wake IRQ with no resume: -13
The wakeirq stays in /proc-interrupts
rebinding shows this:
[ 289.795959] genirq: Flags mismatch irq 112. 0000200a (480b4000.mmc:wakeup) vs. 0000200a (480b4000.mmc:wakeup)
[ 289.808959] omap_hsmmc 480b4000.mmc: Unable to request wake IRQ
[ 289.815338] omap_hsmmc 480b4000.mmc: no SDIO IRQ support, falling back to polling
That bug seems to be introduced by switching from devm_request_irq()
to generic wakeirq handling.
So let us cleanup at removal.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Fixes: 5b83b2234b ("mmc: omap_hsmmc: Change wake-up interrupt to use generic wakeirq")
Cc: stable@vger.kernel.org # v4.2+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 816e846c2e upstream.
Inside of start_xmit() the call to check if the connection is up and the
queueing of the packets for later transmission is not atomic which leaves
a window where cm_rep_handler can run, set the connection up, dequeue
pending packets and leave the subsequently queued packets by start_xmit()
sitting on neigh->queue until they're dropped when the connection is torn
down. This only applies to connected mode. These dropped packets can
really upset TCP, for example, and cause multi-minute delays in
transmission for open connections.
Here's the code in start_xmit where we check to see if the connection is
up:
if (ipoib_cm_get(neigh)) {
if (ipoib_cm_up(neigh)) {
ipoib_cm_send(dev, skb, ipoib_cm_get(neigh));
goto unref;
}
}
The race occurs if cm_rep_handler execution occurs after the above
connection check (specifically if it gets to the point where it acquires
priv->lock to dequeue pending skb's) but before the below code snippet in
start_xmit where packets are queued.
if (skb_queue_len(&neigh->queue) < IPOIB_MAX_PATH_REC_QUEUE) {
push_pseudo_header(skb, phdr->hwaddr);
spin_lock_irqsave(&priv->lock, flags);
__skb_queue_tail(&neigh->queue, skb);
spin_unlock_irqrestore(&priv->lock, flags);
} else {
++dev->stats.tx_dropped;
dev_kfree_skb_any(skb);
}
The patch acquires the netif tx lock in cm_rep_handler for the section
where it sets the connection up and dequeues and retransmits deferred
skb's.
Fixes: 839fcaba35 ("IPoIB: Connected mode experimental support")
Cc: stable@vger.kernel.org
Signed-off-by: Aaron Knister <aaron.s.knister@nasa.gov>
Tested-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8edfe2e992 upstream.
Commit 822fb18a82 ("xen-netfront: wait xenbus state change when load
module manually") added a new wait queue to wait on for a state change
when the module is loaded manually. Unfortunately there is no wakeup
anywhere to stop that waiting.
Instead of introducing a new wait queue rename the existing
module_unload_q to module_wq and use it for both purposes (loading and
unloading).
As any state change of the backend might be intended to stop waiting
do the wake_up_all() in any case when netback_changed() is called.
Fixes: 822fb18a82 ("xen-netfront: wait xenbus state change when load module manually")
Cc: <stable@vger.kernel.org> #4.18
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 831b624df1 upstream.
persistent_ram_vmap() returns the page start vaddr.
persistent_ram_iomap() supports non-page-aligned mapping.
persistent_ram_buffer_map() always adds offset-in-page to the vaddr
returned from these two functions, which causes incorrect mapping of
non-page-aligned persistent ram buffer.
By default ftrace_size is 4096 and max_ftrace_cnt is nr_cpu_ids. Without
this patch, the zone_sz in ramoops_init_przs() is 4096/nr_cpu_ids which
might not be page aligned. If the offset-in-page > 2048, the vaddr will be
in next page. If the next page is not mapped, it will cause kernel panic:
[ 0.074231] BUG: unable to handle kernel paging request at ffffa19e0081b000
...
[ 0.075000] RIP: 0010:persistent_ram_new+0x1f8/0x39f
...
[ 0.075000] Call Trace:
[ 0.075000] ramoops_init_przs.part.10.constprop.15+0x105/0x260
[ 0.075000] ramoops_probe+0x232/0x3a0
[ 0.075000] platform_drv_probe+0x3e/0xa0
[ 0.075000] driver_probe_device+0x2cd/0x400
[ 0.075000] __driver_attach+0xe4/0x110
[ 0.075000] ? driver_probe_device+0x400/0x400
[ 0.075000] bus_for_each_dev+0x70/0xa0
[ 0.075000] driver_attach+0x1e/0x20
[ 0.075000] bus_add_driver+0x159/0x230
[ 0.075000] ? do_early_param+0x95/0x95
[ 0.075000] driver_register+0x70/0xc0
[ 0.075000] ? init_pstore_fs+0x4d/0x4d
[ 0.075000] __platform_driver_register+0x36/0x40
[ 0.075000] ramoops_init+0x12f/0x131
[ 0.075000] do_one_initcall+0x4d/0x12c
[ 0.075000] ? do_early_param+0x95/0x95
[ 0.075000] kernel_init_freeable+0x19b/0x222
[ 0.075000] ? rest_init+0xbb/0xbb
[ 0.075000] kernel_init+0xe/0xfc
[ 0.075000] ret_from_fork+0x3a/0x50
Signed-off-by: Bin Yang <bin.yang@intel.com>
[kees: add comments describing the mapping differences, updated commit log]
Fixes: 24c3d2f342 ("staging: android: persistent_ram: Make it possible to use memory outside of bootmem")
Cc: stable@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 954a8e3aea upstream.
When AF_IB addresses are used during rdma_resolve_addr() a lock is not
held. A cma device can get removed while list traversal is in progress
which may lead to crash. ie
CPU0 CPU1
==== ====
rdma_resolve_addr()
cma_resolve_ib_dev()
list_for_each() cma_remove_one()
cur_dev->device mutex_lock(&lock)
list_del();
mutex_unlock(&lock);
cma_process_remove();
Therefore, hold a lock while traversing the list which avoids such
situation.
Cc: <stable@vger.kernel.org> # 3.10
Fixes: f17df3b0de ("RDMA/cma: Add support for AF_IB to rdma_resolve_addr()")
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0e7d4d932f ]
This patch fixes two typos related to unregistering algorithms supported by
SAHARAH 3. In sahara_register_algs the wrong algorithms are unregistered
in case of an error. In sahara_unregister_algs the wrong array is used to
determine the iteration count.
Signed-off-by: Michael Müller <michael@fds-team.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8bbafed8dd ]
The mv_xor_v2 driver uses a tasklet, initialized during the probe()
routine. However, it forgets to cleanup the tasklet using
tasklet_kill() function during the remove() routine, which this patch
fixes. This prevents the tasklet from potentially running after the
module has been removed.
Fixes: 19a340b1a8 ("dmaengine: mv_xor_v2: new driver")
Signed-off-by: Hanna Hawa <hannah@marvell.com>
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3297c8fc65 ]
There is a race window in device_shutdown(), which may cause
-1. parent device shut down before child or
-2. no shutdown on a new probing device.
For 1st, taking the following scenario:
device_shutdown new plugin device
list_del_init(parent_dev);
spin_unlock(list_lock);
device_add(child)
probe child
shutdown parent_dev
--> now child is on the tail of devices_kset
For 2nd, taking the following scenario:
device_shutdown new plugin device
device_add(dev)
device_lock(dev);
...
device_unlock(dev);
probe dev
--> now, the new occurred dev has no opportunity to shutdown
To fix this race issue, just prevent the new probing request. With this
logic, device_shutdown() is more similar to dpm_prepare().
Signed-off-by: Pingfan Liu <kernelfans@gmail.com>
Reviewed-by: Rafael J. Wysocki <rafael@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1d47191de7 ]
The vgic_init function can race with kvm_arch_vcpu_create() which does
not hold kvm_lock() and we therefore have no synchronization primitives
to ensure we're doing the right thing.
As the user is trying to initialize or run the VM while at the same time
creating more VCPUs, we just have to refuse to initialize the VGIC in
this case rather than silently failing with a broken VCPU.
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Christoffer Dall <christoffer.dall@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 70551dc46f ]
After the subdriver's remove() routine has completed, the card's layer
mode is undetermined again. Reflect this in the layer2 field.
If qeth_dev_layer2_store() hits an error after remove() was called, the
card _always_ requires a setup(), even if the previous layer mode is
requested again.
But qeth_dev_layer2_store() bails out early if the requested layer mode
still matches the current one. So unless we reset the layer2 field,
re-probing the card back to its previous mode is currently not possible.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a702349a40 ]
By updating q->used_buffers only _after_ do_QDIO() has completed, there
is a potential race against the buffer's TX completion. In the unlikely
case that the TX completion path wins, qeth_qdio_output_handler() would
decrement the counter before qeth_flush_buffers() even incremented it.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e53db01831 ]
Current LED trigger, 'bt', is not known/used by any existing driver.
Fix this by renaming it to 'bluetooth-power' trigger which is
controlled by the Bluetooth subsystem.
Fixes: 9943230c88 ("arm64: dts: qcom: Add apq8016-sbc board LED's related device nodes")
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2d408c0d45 ]
Commit f599c64fdf ("xen-netfront: Fix race between device setup and
open") changed the initialization order: xennet_create_queues() now
happens before we do register_netdev() so using netdev->name in
xennet_init_queue() is incorrect, we end up with the following in
/proc/interrupts:
60: 139 0 xen-dyn -event eth%d-q0-tx
61: 265 0 xen-dyn -event eth%d-q0-rx
62: 234 0 xen-dyn -event eth%d-q1-tx
63: 1 0 xen-dyn -event eth%d-q1-rx
and this looks ugly. Actually, using early netdev name (even when it's
already set) is also not ideal: nowadays we tend to rename eth devices
and queue name may end up not corresponding to the netdev name.
Use nodename from xenbus device for queue naming: this can't change in VM's
lifetime. Now /proc/interrupts looks like
62: 202 0 xen-dyn -event device/vif/0-q0-tx
63: 317 0 xen-dyn -event device/vif/0-q0-rx
64: 262 0 xen-dyn -event device/vif/0-q1-tx
65: 17 0 xen-dyn -event device/vif/0-q1-rx
Fixes: f599c64fdf ("xen-netfront: Fix race between device setup and open")
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Reviewed-by: Ross Lagerwall <ross.lagerwall@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 07300f774f ]
After device is stopped we reset the rings by moving all free buffers
to positions [0, cnt - 2], and clear the position cnt - 1 in the ring.
We then proceed to clear the read/write pointers. This means that if
we try to reset the ring again the code will assume that the next to
fill buffer is at position 0 and swap it with cnt - 1. Since we
previously cleared position cnt - 1 it will lead to leaking the first
buffer and leaving ring in a bad state.
This scenario can only happen if FW communication fails, in which case
the ring will never be used again, so the fact it's in a bad state will
not be noticed. Buffer leak is the only problem. Don't try to move
buffers in the ring if the read/write pointers indicate the ring was
never used or have already been reset.
nfp_net_clear_config_and_disable() is now fully idempotent.
Found by code inspection, FW communication failures are very rare,
and reconfiguring a live device is not common either, so it's unlikely
anyone has ever noticed the leak.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3ea86495ae ]
The BGRT code validates the contents of the table against the UEFI
memory map, and so it expects it to be mapped when the code runs.
On ARM, this is currently not the case, since we tear down the early
mapping after efi_init() completes, and only create the permanent
mapping in arm_enable_runtime_services(), which executes as an early
initcall, but still leaves a window where the UEFI memory map is not
mapped.
So move the call to efi_memmap_unmap() from efi_init() to
arm_enable_runtime_services().
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
[will: fold in EFI_MEMMAP attribute check from Ard]
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 129a998909 ]
A socket which has sk_family set to PF_INET6 is able to receive not
only IPv6 but also IPv4 traffic (IPv4-mapped IPv6 addresses).
Prior to this patch, the smk_skb_to_addr_ipv6() could have been
called for socket buffers containing IPv4 packets, in result such
traffic was allowed.
Signed-off-by: Piotr Sawicki <p.sawicki2@partner.samsung.com>
Signed-off-by: Casey Schaufler <casey@schaufler-ca.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 133bf90dbb ]
As explained in ieee80211_delayed_tailroom_dec(), during roam,
keys of the old AP will be destroyed and new keys will be
installed. Deletion of the old key causes
crypto_tx_tailroom_needed_cnt to go from 1 to 0 and the new key
installation causes a transition from 0 to 1.
Whenever crypto_tx_tailroom_needed_cnt transitions from 0 to 1,
we invoke synchronize_net(); the reason for doing this is to avoid
a race in the TX path as explained in increment_tailroom_need_count().
This synchronize_net() operation can be slow and can affect the station
roam time. To avoid this, decrementing the crypto_tx_tailroom_needed_cnt
is delayed for a while so that upon installation of new key the
transition would be from 1 to 2 instead of 0 to 1 and thereby
improving the roam time.
This is all correct for a STA iftype, but deferring the tailroom_needed
decrement for other iftypes may be unnecessary.
For example, let's consider the case of a 4-addr client connecting to
an AP for which AP_VLAN interface is also created, let the initial
value for tailroom_needed on the AP be 1.
* 4-addr client connects to the AP (AP: tailroom_needed = 1)
* AP will clear old keys, delay decrement of tailroom_needed count
* AP_VLAN is created, it takes the tailroom count from master
(AP_VLAN: tailroom_needed = 1, AP: tailroom_needed = 1)
* Install new key for the station, assume key is plumbed in the HW,
there won't be any change in tailroom_needed count on AP iface
* Delayed decrement of tailroom_needed count on AP
(AP: tailroom_needed = 0, AP_VLAN: tailroom_needed = 1)
Because of the delayed decrement on AP iface, tailroom_needed count goes
out of sync between AP(master iface) and AP_VLAN(slave iface) and
there would be unnecessary tailroom created for the packets going
through AP_VLAN iface.
Also, WARN_ONs were observed while trying to bring down the AP_VLAN
interface:
(warn_slowpath_common) (warn_slowpath_null+0x18/0x20)
(warn_slowpath_null) (ieee80211_free_keys+0x114/0x1e4)
(ieee80211_free_keys) (ieee80211_del_virtual_monitor+0x51c/0x850)
(ieee80211_del_virtual_monitor) (ieee80211_stop+0x30/0x3c)
(ieee80211_stop) (__dev_close_many+0x94/0xb8)
(__dev_close_many) (dev_close_many+0x5c/0xc8)
Restricting delayed decrement to station interface alone fixes the problem
and it makes sense to do so because delayed decrement is done to improve
roam time which is applicable only for client devices.
Signed-off-by: Manikanta Pubbisetty <mpubbise@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c6ea7e9747 ]
Having the zload address at 0x8060.0000 means the size of the
uncompressed kernel cannot be bigger than around 6 MiB, as it is
deflated at address 0x8001.0000.
This limit is too small; a kernel with some built-in drivers and things
like debugfs enabled will already be over 6 MiB in size, and so will
fail to extract properly.
To fix this, we bump the zload address from 0x8060.0000 to 0x8100.0000.
This is fine, as all the boards featuring Ingenic JZ SoCs have at least
32 MiB of RAM, and use u-boot or compatible bootloaders which won't
hardcode the load address but read it from the uImage's header.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/19787/
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit bd90284cc6 ]
The intention here is to consume and discard the remaining buffer
upon error. This works if there has not been a previous partial write.
If there has been, then total_len is no longer total number of bytes
to copy. total_len is always "bytes left to copy", so it should be
added to written bytes.
This code may not be exercised any more if partial writes will not be
hit, but this is a small bugfix before a larger change.
Reviewed-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit cd4806911c ]
For most of Exynos SoCs, Power Management Unit (PMU) address space is
mapped into global variable 'pmu_base_addr' very early when initializing
PMU interrupt controller. A lot of other machine code depends on it so
when doing iounmap() on this address, clear the global as well to avoid
usage of invalid value (pointing to unmapped memory region).
Properly mapped PMU address space is a requirement for all other machine
code so this fix is purely theoretical. Boot will fail immediately in
many other places after following this error path.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1ba0a59cea ]
I discovered the problem when developing a frame buffer driver for the
PlayStation 2 (not yet merged), using the following video modes for the
PlayStation 3 in drivers/video/fbdev/ps3fb.c:
}, {
/* 1080if */
"1080if", 50, 1920, 1080, 13468, 148, 484, 36, 4, 88, 5,
FB_SYNC_BROADCAST, FB_VMODE_INTERLACED
}, {
/* 1080pf */
"1080pf", 50, 1920, 1080, 6734, 148, 484, 36, 4, 88, 5,
FB_SYNC_BROADCAST, FB_VMODE_NONINTERLACED
},
In ps3fb_probe, the mode_option module parameter is used with fb_find_mode
but it can only select the interlaced variant of 1920x1080 since the loop
matching the modes does not take the difference between interlaced and
progressive modes into account.
In short, without the patch, progressive 1920x1080 cannot be chosen as a
mode_option parameter since fb_find_mode (falsely) thinks interlace is a
perfect match.
Signed-off-by: Fredrik Noring <noring@nocrew.org>
Cc: "Maciej W. Rozycki" <macro@linux-mips.org>
[b.zolnierkie: updated patch description]
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b951d80aaf ]
When parsing the video modes from DT properties, make sure to zero out
memory before using it. This is important because not all fields in the mode
struct are explicitly initialized, even though they are used later on.
Fixes: 420a488278 ("video: fbdev: pxafb: initial devicetree conversion")
Reviewed-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9068533e4f ]
For powerpc64, perf will filter out the second entry in the callchain,
i.e. the LR value, if the return address of the function corresponding
to the probed location has already been saved on its caller's stack.
The state of the return address is determined using debug information.
At any point within a function, if the return address is already saved
somewhere, a DWARF expression can tell us about its location. If the
return address in still in LR only, no DWARF expression would exist.
Typically, the instructions in a function's prologue first copy the LR
value to R0 and then pushes R0 on to the stack. If LR has already been
copied to R0 but R0 is yet to be pushed to the stack, we can still get a
DWARF expression that says that the return address is in R0. This is
indicating that getting a DWARF expression for the return address does
not guarantee the fact that it has already been saved on the stack.
This can be observed on a powerpc64le system running Fedora 27 as shown
below.
# objdump -d /usr/lib64/libc-2.26.so | less
...
000000000015af20 <inet_pton>:
15af20: 0b 00 4c 3c addis r2,r12,11
15af24: e0 c1 42 38 addi r2,r2,-15904
15af28: a6 02 08 7c mflr r0
15af2c: f0 ff c1 fb std r30,-16(r1)
15af30: f8 ff e1 fb std r31,-8(r1)
15af34: 78 1b 7f 7c mr r31,r3
15af38: 78 23 83 7c mr r3,r4
15af3c: 78 2b be 7c mr r30,r5
15af40: 10 00 01 f8 std r0,16(r1)
15af44: c1 ff 21 f8 stdu r1,-64(r1)
15af48: 28 00 81 f8 std r4,40(r1)
...
# readelf --debug-dump=frames-interp /usr/lib64/libc-2.26.so | less
...
00027024 0000000000000024 00027028 FDE cie=00000000 pc=000000000015af20..000000000015af88
LOC CFA r30 r31 ra
000000000015af20 r1+0 u u u
000000000015af34 r1+0 c-16 c-8 r0
000000000015af48 r1+64 c-16 c-8 c+16
000000000015af5c r1+0 c-16 c-8 c+16
000000000015af78 r1+0 u u
...
# perf probe -x /usr/lib64/libc-2.26.so -a inet_pton+0x18
# perf record -e probe_libc:inet_pton -g ping -6 -c 1 ::1
# perf script
Before:
ping 2829 [005] 512917.460174: probe_libc:inet_pton: (7fff7e2baf38)
7fff7e2baf38 __GI___inet_pton+0x18 (/usr/lib64/libc-2.26.so)
7fff7e2705b4 getaddrinfo+0x164 (/usr/lib64/libc-2.26.so)
12f152d70 _init+0xbfc (/usr/bin/ping)
7fff7e1836a0 generic_start_main.isra.0+0x140 (/usr/lib64/libc-2.26.so)
7fff7e183898 __libc_start_main+0xb8 (/usr/lib64/libc-2.26.so)
0 [unknown] ([unknown])
After:
ping 2829 [005] 512917.460174: probe_libc:inet_pton: (7fff7e2baf38)
7fff7e2baf38 __GI___inet_pton+0x18 (/usr/lib64/libc-2.26.so)
7fff7e26fa54 gaih_inet.constprop.7+0xf44 (/usr/lib64/libc-2.26.so)
7fff7e2705b4 getaddrinfo+0x164 (/usr/lib64/libc-2.26.so)
12f152d70 _init+0xbfc (/usr/bin/ping)
7fff7e1836a0 generic_start_main.isra.0+0x140 (/usr/lib64/libc-2.26.so)
7fff7e183898 __libc_start_main+0xb8 (/usr/lib64/libc-2.26.so)
0 [unknown] ([unknown])
Reported-by: Ravi Bangoria <ravi.bangoria@linux.ibm.com>
Signed-off-by: Sandipan Das <sandipan@linux.ibm.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Maynard Johnson <maynard@us.ibm.com>
Cc: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Cc: Ravi Bangoria <ravi.bangoria@linux.vnet.ibm.com>
Cc: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Link: http://lkml.kernel.org/r/66e848a7bdf2d43b39210a705ff6d828a0865661.1530724939.git.sandipan@linux.ibm.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b6566b47a6 ]
Fix a build warning in viafbdev.c when CONFIG_PROC_FS is not enabled
by marking the unused function as __maybe_unused.
../drivers/video/fbdev/via/viafbdev.c:1471:12: warning: 'viafb_sup_odev_proc_show' defined but not used [-Wunused-function]
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e79e0e1428 ]
Before this patch, you could get into situations like this:
1. Process 1 searches for X free blocks, finds them, makes a reservation
2. Process 2 searches for free blocks in the same rgrp, but now the
bitmap is full because process 1's reservation is skipped over.
So it marks the bitmap as GBF_FULL.
3. Process 1 tries to allocate blocks from its own reservation, but
since the GBF_FULL bit is set, it skips over the rgrp and searches
elsewhere, thus not using its own reservation.
This patch adds an additional check to allow processes to use their
own reservations.
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1d25e3eeed ]
Fix 2 printk format warnings (this driver is currently only used by
arch/sh/) by using "%pap" instead of "%lx".
Fixes these build warnings:
../drivers/mtd/maps/solutionengine.c: In function 'init_soleng_maps':
../include/linux/kern_levels.h:5:18: warning: format '%lx' expects argument of type 'long unsigned int', but argument 2 has type 'resource_size_t' {aka 'unsigned int'} [-Wformat=]
../drivers/mtd/maps/solutionengine.c:62:54: note: format string is defined here
printk(KERN_NOTICE "Solution Engine: Flash at 0x%08lx, EPROM at 0x%08lx\n",
~~~~^
%08x
../include/linux/kern_levels.h:5:18: warning: format '%lx' expects argument of type 'long unsigned int', but argument 3 has type 'resource_size_t' {aka 'unsigned int'} [-Wformat=]
../drivers/mtd/maps/solutionengine.c:62:72: note: format string is defined here
printk(KERN_NOTICE "Solution Engine: Flash at 0x%08lx, EPROM at 0x%08lx\n",
~~~~^
%08x
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Boris Brezillon <boris.brezillon@bootlin.com>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: linux-mtd@lists.infradead.org
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Rich Felker <dalias@libc.org>
Cc: linux-sh@vger.kernel.org
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 536ca245c5 ]
According to "Annex A16: RDMA over Converged Ethernet (RoCE)":
A16.4.3 MANAGEMENT INTERFACES
As defined in the base specification, a special Queue Pair, QP0 is defined
solely for communication between subnet manager(s) and subnet management
agents. Since such an IB-defined subnet management architecture is outside
the scope of this annex, it follows that there is also no requirement that
a port which conforms to this annex be associated with a QP0. Thus, for
end nodes designed to conform to this annex, the concept of QP0 is
undefined and unused for any port connected to an Ethernet network.
CA16-8: A packet arriving at a RoCE port containing a BTH with the
destination QP field set to QP0 shall be silently dropped.
Signed-off-by: Zhu Yanjun <yanjun.zhu@oracle.com>
Acked-by: Moni Shoua <monis@mellanox.com>
Reviewed-by: Yuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e49756544a ]
In pl330_update() when checking if a channel has been aborted, the
channel's lock is not taken, only the overall pl330_dmac lock. But in
pl330_terminate_all() the aborted flag (req_running==-1) is set under
the channel lock and not the pl330_dmac lock.
With threaded interrupts, this leads to a potential race:
pl330_terminate_all pl330_update
------------------- ------------
lock channel
entry
lock pl330
_stop channel
unlock pl330
lock pl330
check req_running != -1
req_running = -1
_start channel
Signed-off-by: John Keeping <john@metanate.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5a1a2f63d8 ]
The error path currently calls tw686x_video_free() which requires
vc->dev to be initialized, causing a NULL dereference on uninitizalized
channels.
Fix this by setting the vc->dev fields for all the channels first.
Fixes: f8afaa8dbc ("[media] tw686x: Introduce an interface to support multiple DMA modes")
Signed-off-by: Krzysztof Ha?asa <khalasa@piap.pl>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9c2af1c737 ]
If Make gets a fatal signal while a shell is executing, it may delete
the target file that the recipe was supposed to update. This is needed
to make sure that it is remade from scratch when Make is next run; if
Make is interrupted after the recipe has begun to write the target file,
it results in an incomplete file whose time stamp is newer than that
of the prerequisites files. Make automatically deletes the incomplete
file on interrupt unless the target is marked .PRECIOUS.
The situation is just the same as when the shell fails for some reasons.
Usually when a recipe line fails, if it has changed the target file at
all, the file is corrupted, or at least it is not completely updated.
Yet the file’s time stamp says that it is now up to date, so the next
time Make runs, it will not try to update that file.
However, Make does not cater to delete the incomplete target file in
this case. We need to add .DELETE_ON_ERROR somewhere in the Makefile
to request it.
scripts/Kbuild.include seems a suitable place to add it because it is
included from almost all sub-makes.
Please note .DELETE_ON_ERROR is not effective for phony targets.
The external module building should never ever touch the kernel tree.
The following recipe fails if include/generated/autoconf.h is missing.
However, include/config/auto.conf is not deleted since it is a phony
target.
PHONY += include/config/auto.conf
include/config/auto.conf:
$(Q)test -e include/generated/autoconf.h -a -e $@ || ( \
echo >&2; \
echo >&2 " ERROR: Kernel configuration is invalid."; \
echo >&2 " include/generated/autoconf.h or $@ are missing.";\
echo >&2 " Run 'make oldconfig && make prepare' on kernel src to fix it."; \
echo >&2 ; \
/bin/false)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f6dab4233d ]
Fixed factor clock has two initializations at of_clk_init() time
and during platform driver probe. Before of_clk_init() call,
node is marked as populated and so its probe never gets called.
During of_clk_init() fixed factor clock registration may fail if
any of its parent clock is not registered. In this case, it doesn't
get chance to retry registration from probe. Clear OF_POPULATED
flag if fixed factor clock registration fails so that clock
registration is attempted again from probe.
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 11177e7a7a ]
of_find_compatible_node() is returning a device node with refcount
incremented and must be explicitly decremented after the last use
which is right after the us in of_iomap() here.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Fixes: 787b4271a6 ("clk: imx: add imx6ul clk tree support")
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 776125785a ]
To speed up the common case of appending to a file,
gfs2_write_alloc_required presumes that writing beyond the end of a file
will always require additional blocks to be allocated. This assumption
is incorrect for preallocates files, but there are no negative
consequences as long as *some* space is still left on the filesystem.
One special file that always has some space preallocated beyond the end
of the file is the rindex: when growing a filesystem, gfs2_grow adds one
or more new resource groups and appends records describing those
resource groups to the rindex; the preallocated space ensures that this
is always possible.
However, when a filesystem is completely full, gfs2_write_alloc_required
will indicate that an additional allocation is required, and appending
the next record to the rindex will fail even though space for that
record has already been preallocated. To fix that, skip the incorrect
optimization in gfs2_write_alloc_required, but for the rindex only.
Other writes to preallocated space beyond the end of the file are still
allowed to fail on completely full filesystems.
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Reviewed-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit bd1cd0eb2c ]
AU0828_DEVICE() macro in quirks-table.h uses USB_DEVICE_VENDOR_SPEC()
for expanding idVendor and idProduct fields. However, the latter
macro adds also match_flags and bInterfaceClass, which are different
from the values AU0828_DEVICE() macro sets after that.
For fixing them, just expand idVendor and idProduct fields manually in
AU0828_DEVICE().
This fixes sparse warnings like:
sound/usb/quirks-table.h:2892:1: warning: Initializer entry defined twice
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5df816e7f4 ]
When initializing the device (procedure init_one), the driver
calls mlx5_pci_init to perform pci initialization. As part of this
initialization, mlx5_pci_init creates a debugfs directory.
If this creation fails, init_one aborts, returning failure to
the caller (which is the probe method caller).
The main reason for such a failure to occur is if the debugfs
directory already exists. This can happen if the last time
mlx5_pci_close was called, debugfs_remove (silently) failed due
to the debugfs directory not being empty.
Guarantee that such a debugfs_remove failure will not occur by
instead calling debugfs_remove_recursive in procedure mlx5_pci_close.
Fixes: 59211bd3b6 ("net/mlx5: Split the load/unload flow into hardware and software flows")
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 76d5581c87 ]
When the mlx5 health mechanism detects a problem while the driver
is in the middle of init_one or remove_one, the driver needs to prevent
the health mechanism from scheduling future work; if future work
is scheduled, there is a problem with use-after-free: the system WQ
tries to run the work item (which has been freed) at the scheduled
future time.
Prevent this by disabling work item scheduling in the health mechanism
when the driver is in the middle of init_one() or remove_one().
Fixes: e126ba97db ("mlx5: Add driver for Mellanox Connect-IB adapters")
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Reviewed-by: Feras Daoud <ferasda@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit cc4dfb7f70 ]
When a rds sock is bound, it is inserted into the bind_hash_table
which is protected by RCU. But when releasing rds sock, after it
is removed from this hash table, it is freed immediately without
respecting RCU grace period. This could cause some use-after-free
as reported by syzbot.
Mark the rds sock with SOCK_RCU_FREE before inserting it into the
bind_hash_table, so that it would be always freed after a RCU grace
period.
The other problem is in rds_find_bound(), the rds sock could be
freed in between rhashtable_lookup_fast() and rds_sock_addref(),
so we need to extend RCU read lock protection in rds_find_bound()
to close this race condition.
Reported-and-tested-by: syzbot+8967084bcac563795dc6@syzkaller.appspotmail.com
Reported-by: syzbot+93a5839deb355537440f@syzkaller.appspotmail.com
Cc: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Cc: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Cc: rds-devel@oss.oracle.com
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oarcle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
