[ Upstream commit 08a0c6dff9 ]
pl010_set_termios() briefly resets the CR register to zero.
Where does this register write come from?
The PL010 driver's IRQ handler ambauart_int() originally modified the CR
register without holding the port spinlock. ambauart_set_termios() also
modified that register. To prevent concurrent read-modify-writes by the
IRQ handler and to prevent transmission while changing baudrate,
ambauart_set_termios() had to disable interrupts. That is achieved by
writing zero to the CR register.
However in 2004 the PL010 driver was amended to acquire the port
spinlock in the IRQ handler, obviating the need to disable interrupts in
->set_termios():
https://git.kernel.org/history/history/c/157c0342e591
That rendered the CR register write obsolete. Drop it.
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/fcaff16e5b1abb4cc3da5a2879ac13f278b99ed0.1641128728.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 14e2976fba ]
The RPMh regulator driver is much newer and gets more attention, which in
consequence makes it do a few things better. Update qcom_smd-regulator's
probe function to mimic what rpmh-regulator does to address a couple of
issues:
- Probe defer now works correctly, before it used to, well,
kinda just die.. This fixes reliable probing on (at least) PM8994,
because Linux apparently cannot deal with supply map dependencies yet..
- Regulator data is now matched more sanely: regulator data is matched
against each individual regulator node name and throwing an -EINVAL if
data is missing, instead of just assuming everything is fine and
iterating over all subsequent array members.
- status = "disabled" will now work for disabling individual regulators in
DT. Previously it didn't seem to do much if anything at all.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Link: https://lore.kernel.org/r/20211230023442.1123424-1-konrad.dybcio@somainline.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4e4f325a0a ]
The four RGMII interface modes take care of the required RGMII delay
configuration at the PHY and should not be limited by the network MAC
driver. Sadly, gemini was only permitting RGMII mode with no delays,
which would require the required delay to be inserted via PCB tracking
or by the MAC.
However, there are designs that require the PHY to add the delay, which
is impossible without Gemini permitting the other three PHY interface
modes. Fix the driver to allow these.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Link: https://lore.kernel.org/r/E1n4mpT-002PLd-Ha@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f22725c95e ]
Corentin Labbe reports that the SSI 1328 does not work when allowing
the PHY to operate at gigabit speeds, but does work with the generic
PHY driver.
This appears to be because m88e1118_config_init() writes a fixed value
to the MSCR register, claiming that this is to enable 1G speeds.
However, this always sets bits 4 and 5, enabling RGMII transmit and
receive delays. The suspicion is that the original board this was
added for required the delays to make 1G speeds work.
Add the necessary configuration for RGMII delays for the 88E1118 to
bring this into line with the requirements for RGMII support, and thus
make the SSI 1328 work.
Corentin Labbe has tested this on gemini-ssi1328 and gemini-ns2502.
Reported-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 04be6d337d ]
Some AP can possibly try non-standard VHT rate and mac80211 warns and drops
packets, and leads low TCP throughput.
Rate marked as a VHT rate but data is invalid: MCS: 10, NSS: 2
WARNING: CPU: 1 PID: 7817 at net/mac80211/rx.c:4856 ieee80211_rx_list+0x223/0x2f0 [mac8021
Since commit c27aa56a72 ("cfg80211: add VHT rate entries for MCS-10 and MCS-11")
has added, mac80211 adds this support as well.
After this patch, throughput is good and iw can get the bitrate:
rx bitrate: 975.1 MBit/s VHT-MCS 10 80MHz short GI VHT-NSS 2
or
rx bitrate: 1083.3 MBit/s VHT-MCS 11 80MHz short GI VHT-NSS 2
Buglink: https://bugzilla.suse.com/show_bug.cgi?id=1192891
Reported-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://lore.kernel.org/r/20220103013623.17052-1-pkshih@realtek.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9f05c09d6b ]
If we're looking for leafs that point to a data extent we want to record
the extent items that point at our bytenr. At this point we have the
reference and we know for a fact that this leaf should have a reference
to our bytenr. However if there's some sort of corruption we may not
find any references to our leaf, and thus could end up with eie == NULL.
Replace this BUG_ON() with an ASSERT() and then return -EUCLEAN for the
mortals.
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fcba0120ed ]
We search for an extent entry with .offset = -1, which shouldn't be a
thing, but corruption happens. Add an ASSERT() for the developers,
return -EUCLEAN for mortals.
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e96c1197ac ]
The EC/ACPI firmware on Lenovo ThinkPads used to report a status
of "Unknown" when the battery is between the charge start and
charge stop thresholds. On Windows, it reports "Not Charging"
so the quirk has been added to also report correctly.
Now the "status" attribute returns "Not Charging" when the
battery on ThinkPads is not physicaly charging.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 11544d77e3 ]
Some boards(like RX550) seem to have garbage in the upper
16 bits of the vram size register. Check for
this and clamp the size properly. Fixes
boards reporting bogus amounts of vram.
after add this patch,the maximum GPU VRAM size is 64GB,
otherwise only 64GB vram size will be used.
Signed-off-by: Zongmin Zhou<zhouzongmin@kylinos.cn>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1d4e0b3abb ]
ACPICA commit 3dd7e1f3996456ef81bfe14cba29860e8d42949e
According to ACPI 6.4, Section 16.2, the CPU cache flushing is
required on entering to S1, S2, and S3, but the ACPICA code
flushes the CPU cache regardless of the sleep state.
Blind cache flush on entering S5 causes problems for TDX.
Flushing happens with WBINVD that is not supported in the TDX
environment.
TDX only supports S5 and adjusting ACPICA code to conform to the
spec more strictly fixes the issue.
Link: https://github.com/acpica/acpica/commit/3dd7e1f3
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
[ rjw: Subject and changelog edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 24ea5f90ec ]
ACPICA commit d984f12041392fa4156b52e2f7e5c5e7bc38ad9e
If Operand[0] is a reference of the ACPI_REFCLASS_REFOF class,
acpi_ex_opcode_1A_0T_1R () calls acpi_ns_get_attached_object () to
obtain return_desc which may require additional resolution with
the help of acpi_ex_read_data_from_field (). If the latter fails,
the reference counter of the original return_desc is decremented
which is incorrect, because acpi_ns_get_attached_object () does not
increment the reference counter of the object returned by it.
This issue may lead to premature deletion of the attached object
while it is still attached and a use-after-free and crash in the
host OS. For example, this may happen when on evaluation of ref_of()
a local region field where there is no registered handler for the
given Operation Region.
Fix it by making acpi_ex_opcode_1A_0T_1R () return Status right away
after a acpi_ex_read_data_from_field () failure.
Link: https://github.com/acpica/acpica/commit/d984f120
Link: https://github.com/acpica/acpica/pull/685
Reported-by: Lenny Szubowicz <lszubowi@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1cdfe9e346 ]
ACPICA commit c11af67d8f7e3d381068ce7771322f2b5324d687
If original_count is 0 in acpi_ut_update_ref_count (),
acpi_ut_delete_internal_obj () is invoked for the target object, which is
incorrect, because that object has been deleted once already and the
memory allocated to store it may have been reclaimed and allocated
for a different purpose by the host OS. Moreover, a confusing debug
message following the "Reference Count is already zero, cannot
decrement" warning is printed in that case.
To fix this issue, make acpi_ut_update_ref_count () return after finding
that original_count is 0 and printing the above warning.
Link: https://github.com/acpica/acpica/commit/c11af67d
Link: https://github.com/acpica/acpica/pull/652
Reported-by: Mark Asselstine <mark.asselstine@windriver.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f81bdeaf81 ]
ACPICA commit bc02c76d518135531483dfc276ed28b7ee632ce1
The current ACPI_ACCESS_*_WIDTH defines do not provide a way to
test that size is small enough to not cause an overflow when
applied to a 32-bit integer.
Rather than adding more magic numbers, add ACPI_ACCESS_*_SHIFT,
ACPI_ACCESS_*_MAX, and ACPI_ACCESS_*_DEFAULT #defines and
redefine ACPI_ACCESS_*_WIDTH in terms of the new #defines.
This was inititally reported on Linux where a size of 102 in
ACPI_ACCESS_BIT_WIDTH caused an overflow error in the SPCR
initialization code.
Link: https://github.com/acpica/acpica/commit/bc02c76d
Signed-off-by: Mark Langsdorf <mlangsdo@redhat.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aa39cc6757 ]
GC task can deadlock in read_cache_page() because it may attempt
to release a page that is actually allocated by another task in
jffs2_write_begin().
The reason is that in jffs2_write_begin() there is a small window
a cache page is allocated for use but not set Uptodate yet.
This ends up with a deadlock between two tasks:
1) A task (e.g. file copy)
- jffs2_write_begin() locks a cache page
- jffs2_write_end() tries to lock "alloc_sem" from
jffs2_reserve_space() <-- STUCK
2) GC task (jffs2_gcd_mtd3)
- jffs2_garbage_collect_pass() locks "alloc_sem"
- try to lock the same cache page in read_cache_page() <-- STUCK
So to avoid this deadlock, hold "alloc_sem" in jffs2_write_begin()
while reading data in a cache page.
Signed-off-by: Kyeong Yoo <kyeong.yoo@alliedtelesis.co.nz>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6ce708f54c ]
Large pkt_len can lead to out-out-bound memcpy. Current
ath9k_hif_usb_rx_stream allows combining the content of two urb
inputs to one pkt. The first input can indicate the size of the
pkt. Any remaining size is saved in hif_dev->rx_remain_len.
While processing the next input, memcpy is used with rx_remain_len.
4-byte pkt_len can go up to 0xffff, while a single input is 0x4000
maximum in size (MAX_RX_BUF_SIZE). Thus, the patch adds a check for
pkt_len which must not exceed 2 * MAX_RX_BUG_SIZE.
BUG: KASAN: slab-out-of-bounds in ath9k_hif_usb_rx_cb+0x490/0xed7 [ath9k_htc]
Read of size 46393 at addr ffff888018798000 by task kworker/0:1/23
CPU: 0 PID: 23 Comm: kworker/0:1 Not tainted 5.6.0 #63
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996),
BIOS rel-1.10.2-0-g5f4c7b1-prebuilt.qemu-project.org 04/01/2014
Workqueue: events request_firmware_work_func
Call Trace:
<IRQ>
dump_stack+0x76/0xa0
print_address_description.constprop.0+0x16/0x200
? ath9k_hif_usb_rx_cb+0x490/0xed7 [ath9k_htc]
? ath9k_hif_usb_rx_cb+0x490/0xed7 [ath9k_htc]
__kasan_report.cold+0x37/0x7c
? ath9k_hif_usb_rx_cb+0x490/0xed7 [ath9k_htc]
kasan_report+0xe/0x20
check_memory_region+0x15a/0x1d0
memcpy+0x20/0x50
ath9k_hif_usb_rx_cb+0x490/0xed7 [ath9k_htc]
? hif_usb_mgmt_cb+0x2d9/0x2d9 [ath9k_htc]
? _raw_spin_lock_irqsave+0x7b/0xd0
? _raw_spin_trylock_bh+0x120/0x120
? __usb_unanchor_urb+0x12f/0x210
__usb_hcd_giveback_urb+0x1e4/0x380
usb_giveback_urb_bh+0x241/0x4f0
? __hrtimer_run_queues+0x316/0x740
? __usb_hcd_giveback_urb+0x380/0x380
tasklet_action_common.isra.0+0x135/0x330
__do_softirq+0x18c/0x634
irq_exit+0x114/0x140
smp_apic_timer_interrupt+0xde/0x380
apic_timer_interrupt+0xf/0x20
I found the bug using a custome USBFuzz port. It's a research work
to fuzz USB stack/drivers. I modified it to fuzz ath9k driver only,
providing hand-crafted usb descriptors to QEMU.
After fixing the value of pkt_tag to ATH_USB_RX_STREAM_MODE_TAG in QEMU
emulation, I found the KASAN report. The bug is triggerable whenever
pkt_len is above two MAX_RX_BUG_SIZE. I used the same input that crashes
to test the driver works when applying the patch.
Signed-off-by: Zekun Shen <bruceshenzk@gmail.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/YXsidrRuK6zBJicZ@10-18-43-117.dynapool.wireless.nyu.edu
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0055858638 ]
When a new USB device gets plugged to nested hubs, the affected hub,
which connects to usb 2-1.4-port2, doesn't report there's any change,
hence the nested hubs go back to runtime suspend like nothing happened:
[ 281.032951] usb usb2: usb wakeup-resume
[ 281.032959] usb usb2: usb auto-resume
[ 281.032974] hub 2-0:1.0: hub_resume
[ 281.033011] usb usb2-port1: status 0263 change 0000
[ 281.033077] hub 2-0:1.0: state 7 ports 4 chg 0000 evt 0000
[ 281.049797] usb 2-1: usb wakeup-resume
[ 281.069800] usb 2-1: Waited 0ms for CONNECT
[ 281.069810] usb 2-1: finish resume
[ 281.070026] hub 2-1:1.0: hub_resume
[ 281.070250] usb 2-1-port4: status 0203 change 0000
[ 281.070272] usb usb2-port1: resume, status 0
[ 281.070282] hub 2-1:1.0: state 7 ports 4 chg 0010 evt 0000
[ 281.089813] usb 2-1.4: usb wakeup-resume
[ 281.109792] usb 2-1.4: Waited 0ms for CONNECT
[ 281.109801] usb 2-1.4: finish resume
[ 281.109991] hub 2-1.4:1.0: hub_resume
[ 281.110147] usb 2-1.4-port2: status 0263 change 0000
[ 281.110234] usb 2-1-port4: resume, status 0
[ 281.110239] usb 2-1-port4: status 0203, change 0000, 10.0 Gb/s
[ 281.110266] hub 2-1.4:1.0: state 7 ports 4 chg 0000 evt 0000
[ 281.110426] hub 2-1.4:1.0: hub_suspend
[ 281.110565] usb 2-1.4: usb auto-suspend, wakeup 1
[ 281.130998] hub 2-1:1.0: hub_suspend
[ 281.137788] usb 2-1: usb auto-suspend, wakeup 1
[ 281.142935] hub 2-0:1.0: state 7 ports 4 chg 0000 evt 0000
[ 281.177828] usb 2-1: usb wakeup-resume
[ 281.197839] usb 2-1: Waited 0ms for CONNECT
[ 281.197850] usb 2-1: finish resume
[ 281.197984] hub 2-1:1.0: hub_resume
[ 281.198203] usb 2-1-port4: status 0203 change 0000
[ 281.198228] usb usb2-port1: resume, status 0
[ 281.198237] hub 2-1:1.0: state 7 ports 4 chg 0010 evt 0000
[ 281.217835] usb 2-1.4: usb wakeup-resume
[ 281.237834] usb 2-1.4: Waited 0ms for CONNECT
[ 281.237845] usb 2-1.4: finish resume
[ 281.237990] hub 2-1.4:1.0: hub_resume
[ 281.238067] usb 2-1.4-port2: status 0263 change 0000
[ 281.238148] usb 2-1-port4: resume, status 0
[ 281.238152] usb 2-1-port4: status 0203, change 0000, 10.0 Gb/s
[ 281.238166] hub 2-1.4:1.0: state 7 ports 4 chg 0000 evt 0000
[ 281.238385] hub 2-1.4:1.0: hub_suspend
[ 281.238523] usb 2-1.4: usb auto-suspend, wakeup 1
[ 281.258076] hub 2-1:1.0: hub_suspend
[ 281.265744] usb 2-1: usb auto-suspend, wakeup 1
[ 281.285976] hub 2-0:1.0: hub_suspend
[ 281.285988] usb usb2: bus auto-suspend, wakeup 1
USB 3.2 spec, 9.2.5.4 "Changing Function Suspend State" says that "If
the link is in a non-U0 state, then the device must transition the link
to U0 prior to sending the remote wake message", but the hub only
transits the link to U0 after signaling remote wakeup.
So be more forgiving and use a 20ms delay to let the link transit to U0
for remote wakeup.
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Link: https://lore.kernel.org/r/20211215120108.336597-1-kai.heng.feng@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2b14cbd643 ]
The Tegra186 CCPLEX cluster register region is 4 MiB is length, not 4
MiB - 1. This was likely presumed to be the "limit" rather than length.
Fix it up.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8f110f5306 ]
Due to the audit control mutex necessary for serializing audit
userspace messages we haven't been able to block/penalize userspace
processes that attempt to send audit records while the system is
under audit pressure. The result is that privileged userspace
applications have a priority boost with respect to audit as they are
not bound by the same audit queue throttling as the other tasks on
the system.
This patch attempts to restore some balance to the system when under
audit pressure by blocking these privileged userspace tasks after
they have finished their audit processing, and dropped the audit
control mutex, but before they return to userspace.
Reported-by: Gaosheng Cui <cuigaosheng1@huawei.com>
Tested-by: Gaosheng Cui <cuigaosheng1@huawei.com>
Reviewed-by: Richard Guy Briggs <rgb@redhat.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8c3e5b74b9 ]
The mmc core takes a specific path to support initializing of a
non-standard SDIO card. This is triggered by looking for the card-quirk,
MMC_QUIRK_NONSTD_SDIO.
In mmc_sdio_init_card() this gets rather messy, as it causes the code to
bail out earlier, compared to the usual path. This leads to that the OCR
doesn't get saved properly in card->ocr. Fortunately, only omap_hsmmc has
been using the MMC_QUIRK_NONSTD_SDIO and is dealing with the issue, by
assigning a hardcoded value (0x80) to card->ocr from an ->init_card() ops.
To make the behaviour consistent, let's instead rely on the core to save
the OCR in card->ocr during initialization.
Reported-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Link: https://lore.kernel.org/r/e7936cff7fc24d187ef2680d3b4edb0ade58f293.1636564631.git.hns@goldelico.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3af86b0469 ]
In hexium_attach(dev, info), saa7146_vv_init() is called to allocate
a new memory for dev->vv_data. saa7146_vv_release() will be called on
failure of saa7146_register_device(). There is a dereference of
dev->vv_data in saa7146_vv_release(), which could lead to a NULL
pointer dereference on failure of saa7146_vv_init().
Fix this bug by adding a check of saa7146_vv_init().
This bug was found by a static analyzer. The analysis employs
differential checking to identify inconsistent security operations
(e.g., checks or kfrees) between two code paths and confirms that the
inconsistent operations are not recovered in the current function or
the callers, so they constitute bugs.
Note that, as a bug found by static analysis, it can be a false
positive or hard to trigger. Multiple researchers have cross-reviewed
the bug.
Builds with CONFIG_VIDEO_HEXIUM_GEMINI=m show no new warnings,
and our static analyzer no longer warns about this code.
Link: https://lore.kernel.org/linux-media/20211203154030.111210-1-zhou1615@umn.edu
Signed-off-by: Zhou Qingyang <zhou1615@umn.edu>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8fede658e7 ]
Without this, some IR will be missing mid-stream and we might decode
something which never really occurred.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2cbad98903 ]
The WARN_ONCE() in bpf_warn_invalid_xdp_action() can be triggered by
any bugged program, and even attaching a correct program to a NIC
not supporting the given action.
The resulting splat, beyond polluting the logs, fouls automated tools:
e.g. a syzkaller reproducers using an XDP program returning an
unsupported action will never pass validation.
Replace the WARN_ONCE with a less intrusive pr_warn_once().
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/bpf/016ceec56e4817ebb2a9e35ce794d5c917df572c.1638189075.git.pabeni@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3c7ce80a81 ]
And allow instrumentation inside it because it does calls to other
facilities which will not be tagged noinstr.
Fixes
vmlinux.o: warning: objtool: do_machine_check()+0xc73: call to mce_panic() leaves .noinstr.text section
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lore.kernel.org/r/20211208111343.8130-8-bp@alien8.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d7dac08341 ]
When updating Rx and Tx queue kobjects, the queue count should always be
updated to match the queue kobjects count. This was not done in the net
device unregistration path, fix it. Tracking all queue count updates
will allow in a following up patch to detect illegal updates.
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e8a91863eb ]
While running stress tests in roaming scenarios (switching ap's every 5
seconds, we discovered a issue which leads to tx hangings of exactly 5
seconds while or after scanning for new accesspoints. We found out that
this hanging is triggered by ath10k_mac_wait_tx_complete since the
empty_tx_wq was not wake when the num_tx_pending counter reaches zero.
To fix this, we simply move the wake_up call to htt_tx_dec_pending,
since this call was missed on several locations within the ath10k code.
Signed-off-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20210505085806.11474-1-s.gottschall@dd-wrt.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit db66abeea3 ]
If userspace installs a lot of multicast groups very quickly, then
we may run out of command queue space as we send the updates in an
asynchronous fashion (due to locking concerns), and the CPU can
create them faster than the firmware can process them. This is true
even when mac80211 has a work struct that gets scheduled.
Fix this by synchronizing with the firmware after sending all those
commands - outside of the iteration we can send a synchronous echo
command that just has the effect of the CPU waiting for the prior
asynchronous commands to finish. This also will cause fewer of the
commands to be sent to the firmware overall, because the work will
only run once when rescheduled multiple times while it's running.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=213649
Suggested-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reported-by: Maximilian Ernestus <maximilian@ernestus.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20211204083238.51aea5b79ea4.I88a44798efda16e9fe480fb3e94224931d311b29@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 348df80353 ]
In hexium_attach(dev, info), saa7146_vv_init() is called to allocate
a new memory for dev->vv_data. In hexium_detach(), saa7146_vv_release()
will be called and there is a dereference of dev->vv_data in
saa7146_vv_release(), which could lead to a NULL pointer dereference
on failure of saa7146_vv_init() according to the following logic.
Both hexium_attach() and hexium_detach() are callback functions of
the variable 'extension', so there exists a possible call chain directly
from hexium_attach() to hexium_detach():
hexium_attach(dev, info) -- fail to alloc memory to dev->vv_data
| in saa7146_vv_init().
|
|
hexium_detach() -- a dereference of dev->vv_data in saa7146_vv_release()
Fix this bug by adding a check of saa7146_vv_init().
This bug was found by a static analyzer. The analysis employs
differential checking to identify inconsistent security operations
(e.g., checks or kfrees) between two code paths and confirms that the
inconsistent operations are not recovered in the current function or
the callers, so they constitute bugs.
Note that, as a bug found by static analysis, it can be a false
positive or hard to trigger. Multiple researchers have cross-reviewed
the bug.
Builds with CONFIG_VIDEO_HEXIUM_ORION=m show no new warnings,
and our static analyzer no longer warns about this code.
Signed-off-by: Zhou Qingyang <zhou1615@umn.edu>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c8ed7d2f61 ]
Some uvc devices appear to require the maximum allowed USB timeout
for GET_CUR/SET_CUR requests.
So lets just bump the UVC control timeout to 5 seconds which is the
same as the usb ctrl get/set defaults:
USB_CTRL_GET_TIMEOUT 5000
USB_CTRL_SET_TIMEOUT 5000
It fixes the following runtime warnings:
Failed to query (GET_CUR) UVC control 11 on unit 2: -110 (exp. 1).
Failed to query (SET_CUR) UVC control 3 on unit 2: -110 (exp. 2).
Signed-off-by: James Hilliard <james.hilliard1@gmail.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f1cb3476e4 ]
rsi_get_* functions rely on an offset variable from usb
input. The size of usb input is RSI_MAX_RX_USB_PKT_SIZE(3000),
while 2-byte offset can be up to 0xFFFF. Thus a large offset
can cause out-of-bounds read.
The patch adds a bound checking condition when rcv_pkt_len is 0,
indicating it's USB. It's unclear whether this is triggerable
from other type of bus. The following check might help in that case.
offset > rcv_pkt_len - FRAME_DESC_SZ
The bug is trigerrable with conpromised/malfunctioning USB devices.
I tested the patch with the crashing input and got no more bug report.
Attached is the KASAN report from fuzzing.
BUG: KASAN: slab-out-of-bounds in rsi_read_pkt+0x42e/0x500 [rsi_91x]
Read of size 2 at addr ffff888019439fdb by task RX-Thread/227
CPU: 0 PID: 227 Comm: RX-Thread Not tainted 5.6.0 #66
Call Trace:
dump_stack+0x76/0xa0
print_address_description.constprop.0+0x16/0x200
? rsi_read_pkt+0x42e/0x500 [rsi_91x]
? rsi_read_pkt+0x42e/0x500 [rsi_91x]
__kasan_report.cold+0x37/0x7c
? rsi_read_pkt+0x42e/0x500 [rsi_91x]
kasan_report+0xe/0x20
rsi_read_pkt+0x42e/0x500 [rsi_91x]
rsi_usb_rx_thread+0x1b1/0x2fc [rsi_usb]
? rsi_probe+0x16a0/0x16a0 [rsi_usb]
? _raw_spin_lock_irqsave+0x7b/0xd0
? _raw_spin_trylock_bh+0x120/0x120
? __wake_up_common+0x10b/0x520
? rsi_probe+0x16a0/0x16a0 [rsi_usb]
kthread+0x2b5/0x3b0
? kthread_create_on_node+0xd0/0xd0
ret_from_fork+0x22/0x40
Reported-by: Brendan Dolan-Gavitt <brendandg@nyu.edu>
Signed-off-by: Zekun Shen <bruceshenzk@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/YXxXS4wgu2OsmlVv@10-18-43-117.dynapool.wireless.nyu.edu
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 04d80663f6 ]
Currently, with an unknown recv_type, mwifiex_usb_recv
just return -1 without restoring the skb. Next time
mwifiex_usb_rx_complete is invoked with the same skb,
calling skb_put causes skb_over_panic.
The bug is triggerable with a compromised/malfunctioning
usb device. After applying the patch, skb_over_panic
no longer shows up with the same input.
Attached is the panic report from fuzzing.
skbuff: skb_over_panic: text:000000003bf1b5fa
len:2048 put:4 head:00000000dd6a115b data:000000000a9445d8
tail:0x844 end:0x840 dev:<NULL>
kernel BUG at net/core/skbuff.c:109!
invalid opcode: 0000 [#1] SMP KASAN NOPTI
CPU: 0 PID: 198 Comm: in:imklog Not tainted 5.6.0 #60
RIP: 0010:skb_panic+0x15f/0x161
Call Trace:
<IRQ>
? mwifiex_usb_rx_complete+0x26b/0xfcd [mwifiex_usb]
skb_put.cold+0x24/0x24
mwifiex_usb_rx_complete+0x26b/0xfcd [mwifiex_usb]
__usb_hcd_giveback_urb+0x1e4/0x380
usb_giveback_urb_bh+0x241/0x4f0
? __hrtimer_run_queues+0x316/0x740
? __usb_hcd_giveback_urb+0x380/0x380
tasklet_action_common.isra.0+0x135/0x330
__do_softirq+0x18c/0x634
irq_exit+0x114/0x140
smp_apic_timer_interrupt+0xde/0x380
apic_timer_interrupt+0xf/0x20
</IRQ>
Reported-by: Brendan Dolan-Gavitt <brendandg@nyu.edu>
Signed-off-by: Zekun Shen <bruceshenzk@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/YX4CqjfRcTa6bVL+@Zekuns-MBP-16.fios-router.home
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a1ee1c08fc ]
cl is freed on error of calling device_register, but this
object is return later, which will cause uaf issue. Fix it
by return NULL on error.
Signed-off-by: Chengfeng Ye <cyeaa@connect.ust.hk>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bdfd6ab8fd ]
If the IRQ is already in use, then acpi_dev_gpio_irq_get_by() really
should not change the type underneath the current owner.
I specifically hit an issue with this an a Chuwi Hi8 Super (CWI509) Bay
Trail tablet, when the Boot OS selection in the BIOS is set to Android.
In this case _STA for a MAX17047 ACPI I2C device wrongly returns 0xf and
the _CRS resources for this device include a GpioInt pointing to a GPIO
already in use by an _AEI handler, with a different type then specified
in the _CRS for the MAX17047 device. Leading to the acpi_dev_gpio_irq_get()
call done by the i2c-core-acpi.c code changing the type breaking the
_AEI handler.
Now this clearly is a bug in the DSDT of this tablet (in Android mode),
but in general calling irq_set_irq_type() on an IRQ which already is
in use seems like a bad idea.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c1020d3cf4 ]
On an arm64 platform with the Spectrum ASIC, after loading and executing
a new kernel via kexec, the following trace [1] is observed. This seems
to be caused by the fact that the device is not properly shutdown before
executing the new kernel.
Fix this by implementing a shutdown method which mirrors the remove
method, as recommended by the kexec maintainer [2][3].
[1]
BUG: Bad page state in process devlink pfn:22f73d
page:fffffe00089dcf40 refcount:-1 mapcount:0 mapping:0000000000000000 index:0x0
flags: 0x2ffff00000000000()
raw: 2ffff00000000000 0000000000000000 ffffffff089d0201 0000000000000000
raw: 0000000000000000 0000000000000000 ffffffffffffffff 0000000000000000
page dumped because: nonzero _refcount
Modules linked in:
CPU: 1 PID: 16346 Comm: devlink Tainted: G B 5.8.0-rc6-custom-273020-gac6b365b1bf5 #44
Hardware name: Marvell Armada 7040 TX4810M (DT)
Call trace:
dump_backtrace+0x0/0x1d0
show_stack+0x1c/0x28
dump_stack+0xbc/0x118
bad_page+0xcc/0xf8
check_free_page_bad+0x80/0x88
__free_pages_ok+0x3f8/0x418
__free_pages+0x38/0x60
kmem_freepages+0x200/0x2a8
slab_destroy+0x28/0x68
slabs_destroy+0x60/0x90
___cache_free+0x1b4/0x358
kfree+0xc0/0x1d0
skb_free_head+0x2c/0x38
skb_release_data+0x110/0x1a0
skb_release_all+0x2c/0x38
consume_skb+0x38/0x130
__dev_kfree_skb_any+0x44/0x50
mlxsw_pci_rdq_fini+0x8c/0xb0
mlxsw_pci_queue_fini.isra.0+0x28/0x58
mlxsw_pci_queue_group_fini+0x58/0x88
mlxsw_pci_aqs_fini+0x2c/0x60
mlxsw_pci_fini+0x34/0x50
mlxsw_core_bus_device_unregister+0x104/0x1d0
mlxsw_devlink_core_bus_device_reload_down+0x2c/0x48
devlink_reload+0x44/0x158
devlink_nl_cmd_reload+0x270/0x290
genl_rcv_msg+0x188/0x2f0
netlink_rcv_skb+0x5c/0x118
genl_rcv+0x3c/0x50
netlink_unicast+0x1bc/0x278
netlink_sendmsg+0x194/0x390
__sys_sendto+0xe0/0x158
__arm64_sys_sendto+0x2c/0x38
el0_svc_common.constprop.0+0x70/0x168
do_el0_svc+0x28/0x88
el0_sync_handler+0x88/0x190
el0_sync+0x140/0x180
[2]
https://www.mail-archive.com/linux-kernel@vger.kernel.org/msg1195432.html
[3]
https://patchwork.kernel.org/project/linux-scsi/patch/20170212214920.28866-1-anton@ozlabs.org/#20116693
Cc: Eric Biederman <ebiederm@xmission.com>
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a5fe7864d8 ]
When a keyboard without a function key is detected, instead of removing
all quirks, remove only the APPLE_HAS_FN quirk.
Signed-off-by: José Expósito <jose.exposito89@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
