commit 77baa5bafcbe1b2a15ef9c37232c21279c95481c upstream.
In extreme test scenarios:
the 14th field utime in /proc/xx/stat is greater than sum_exec_runtime,
utime = 18446744073709518790 ns, rtime = 135989749728000 ns
In cputime_adjust() process, stime is greater than rtime due to
mul_u64_u64_div_u64() precision problem.
before call mul_u64_u64_div_u64(),
stime = 175136586720000, rtime = 135989749728000, utime = 1416780000.
after call mul_u64_u64_div_u64(),
stime = 135989949653530
unsigned reversion occurs because rtime is less than stime.
utime = rtime - stime = 135989749728000 - 135989949653530
= -199925530
= (u64)18446744073709518790
Trigger condition:
1). User task run in kernel mode most of time
2). ARM64 architecture
3). TICK_CPU_ACCOUNTING=y
CONFIG_VIRT_CPU_ACCOUNTING_NATIVE is not set
Fix mul_u64_u64_div_u64() conversion precision by reset stime to rtime
Fixes: 3dc167ba57 ("sched/cputime: Improve cputime_adjust()")
Signed-off-by: Zheng Zucheng <zhengzucheng@huawei.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: <stable@vger.kernel.org>
Link: https://lkml.kernel.org/r/20240726023235.217771-1-zhengzucheng@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 82dbb57ac8d06dfe8227ba9ab11a49de2b475ae5 upstream.
Some firmware versions of the 9600 series SAS HBA byte-swap the REPORT
ZONES command reply buffer from ATA-ZAC devices by directly accessing the
buffer in the host memory. This does not respect the default command DMA
direction and causes IOMMU page faults on architectures with an IOMMU
enforcing write-only mappings for DMA_FROM_DEVICE DMA driection (e.g. AMD
hosts).
scsi 18:0:0:0: Direct-Access-ZBC ATA WDC WSH722020AL W870 PQ: 0 ANSI: 6
scsi 18:0:0:0: SATA: handle(0x0027), sas_addr(0x300062b2083e7c40), phy(0), device_name(0x5000cca29dc35e11)
scsi 18:0:0:0: enclosure logical id (0x300062b208097c40), slot(0)
scsi 18:0:0:0: enclosure level(0x0000), connector name( C0.0)
scsi 18:0:0:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y)
scsi 18:0:0:0: qdepth(32), tagged(1), scsi_level(7), cmd_que(1)
sd 18:0:0:0: Attached scsi generic sg2 type 20
sd 18:0:0:0: [sdc] Host-managed zoned block device
mpt3sas 0000:41:00.0: AMD-Vi: Event logged [IO_PAGE_FAULT domain=0x0021 address=0xfff9b200 flags=0x0050]
mpt3sas 0000:41:00.0: AMD-Vi: Event logged [IO_PAGE_FAULT domain=0x0021 address=0xfff9b300 flags=0x0050]
mpt3sas_cm0: mpt3sas_ctl_pre_reset_handler: Releasing the trace buffer due to adapter reset.
mpt3sas_cm0 fault info from func: mpt3sas_base_make_ioc_ready
mpt3sas_cm0: fault_state(0x2666)!
mpt3sas_cm0: sending diag reset !!
mpt3sas_cm0: diag reset: SUCCESS
sd 18:0:0:0: [sdc] REPORT ZONES start lba 0 failed
sd 18:0:0:0: [sdc] REPORT ZONES: Result: hostbyte=DID_RESET driverbyte=DRIVER_OK
sd 18:0:0:0: [sdc] 0 4096-byte logical blocks: (0 B/0 B)
Avoid such issue by always mapping the buffer of REPORT ZONES commands
using DMA_BIDIRECTIONAL (read+write IOMMU mapping). This is done by
introducing the helper function _base_scsi_dma_map() and using this helper
in _base_build_sg_scmd() and _base_build_sg_scmd_ieee() instead of calling
directly scsi_dma_map().
Fixes: 471ef9d4e4 ("mpt3sas: Build MPI SGL LIST on GEN2 HBAs and IEEE SGL LIST on GEN3 HBAs")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Link: https://lore.kernel.org/r/20240719073913.179559-3-dlemoal@kernel.org
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b88f55389ad27f05ed84af9e1026aa64dbfabc9a upstream.
The kernel sleep profile is no longer working due to a recursive locking
bug introduced by commit 42a20f86dc ("sched: Add wrapper for get_wchan()
to keep task blocked")
Booting with the 'profile=sleep' kernel command line option added or
executing
# echo -n sleep > /sys/kernel/profiling
after boot causes the system to lock up.
Lockdep reports
kthreadd/3 is trying to acquire lock:
ffff93ac82e08d58 (&p->pi_lock){....}-{2:2}, at: get_wchan+0x32/0x70
but task is already holding lock:
ffff93ac82e08d58 (&p->pi_lock){....}-{2:2}, at: try_to_wake_up+0x53/0x370
with the call trace being
lock_acquire+0xc8/0x2f0
get_wchan+0x32/0x70
__update_stats_enqueue_sleeper+0x151/0x430
enqueue_entity+0x4b0/0x520
enqueue_task_fair+0x92/0x6b0
ttwu_do_activate+0x73/0x140
try_to_wake_up+0x213/0x370
swake_up_locked+0x20/0x50
complete+0x2f/0x40
kthread+0xfb/0x180
However, since nobody noticed this regression for more than two years,
let's remove 'profile=sleep' support based on the assumption that nobody
needs this functionality.
Fixes: 42a20f86dc ("sched: Add wrapper for get_wchan() to keep task blocked")
Cc: stable@vger.kernel.org # v5.16+
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ed0172af5d6fc07d1b40ca82f5ca3979300369f7 ]
We've observed NFS clients with sync tasks sleeping in __rpc_execute
waiting on RPC_TASK_QUEUED that have not responded to a wake-up from
rpc_make_runnable(). I suspect this problem usually goes unnoticed,
because on a busy client the task will eventually be re-awoken by another
task completion or xprt event. However, if the state manager is draining
the slot table, a sync task missing a wake-up can result in a hung client.
We've been able to prove that the waker in rpc_make_runnable() successfully
calls wake_up_bit() (ie- there's no race to tk_runstate), but the
wake_up_bit() call fails to wake the waiter. I suspect the waker is
missing the load of the bit's wait_queue_head, so waitqueue_active() is
false. There are some very helpful comments about this problem above
wake_up_bit(), prepare_to_wait(), and waitqueue_active().
Fix this by inserting smp_mb__after_atomic() before the wake_up_bit(),
which pairs with prepare_to_wait() calling set_current_state().
Signed-off-by: Benjamin Coddington <bcodding@redhat.com>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bf365071ea92b9579d5a272679b74052a5643e35 ]
When a task waiting for completion of a Store Data operation is
interrupted, an attempt is made to halt this operation. If this attempt
fails due to a hardware or firmware problem, there is a chance that the
SCLP facility might store data into buffers referenced by the original
operation at a later time.
Handle this situation by not releasing the referenced data buffers if
the halt attempt fails. For current use cases, this might result in a
leak of few pages of memory in case of a rare hardware/firmware
malfunction.
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Peter Oberparleiter <oberpar@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 68594cec291ff9523b9feb3f43fd853dcddd1f60 ]
syzkaller reported use-after-free in load_firmware_cb() [1].
The reason is because the module allocated a struct tuner in tuner_probe(),
and then the module initialization failed, the struct tuner was released.
A worker which created during module initialization accesses this struct
tuner later, it caused use-after-free.
The process is as follows:
task-6504 worker_thread
tuner_probe <= alloc dvb_frontend [2]
...
request_firmware_nowait <= create a worker
...
tuner_remove <= free dvb_frontend
...
request_firmware_work_func <= the firmware is ready
load_firmware_cb <= but now the dvb_frontend has been freed
To fix the issue, check the dvd_frontend in load_firmware_cb(), if it is
null, report a warning and just return.
[1]:
==================================================================
BUG: KASAN: use-after-free in load_firmware_cb+0x1310/0x17a0
Read of size 8 at addr ffff8000d7ca2308 by task kworker/2:3/6504
Call trace:
load_firmware_cb+0x1310/0x17a0
request_firmware_work_func+0x128/0x220
process_one_work+0x770/0x1824
worker_thread+0x488/0xea0
kthread+0x300/0x430
ret_from_fork+0x10/0x20
Allocated by task 6504:
kzalloc
tuner_probe+0xb0/0x1430
i2c_device_probe+0x92c/0xaf0
really_probe+0x678/0xcd0
driver_probe_device+0x280/0x370
__device_attach_driver+0x220/0x330
bus_for_each_drv+0x134/0x1c0
__device_attach+0x1f4/0x410
device_initial_probe+0x20/0x30
bus_probe_device+0x184/0x200
device_add+0x924/0x12c0
device_register+0x24/0x30
i2c_new_device+0x4e0/0xc44
v4l2_i2c_new_subdev_board+0xbc/0x290
v4l2_i2c_new_subdev+0xc8/0x104
em28xx_v4l2_init+0x1dd0/0x3770
Freed by task 6504:
kfree+0x238/0x4e4
tuner_remove+0x144/0x1c0
i2c_device_remove+0xc8/0x290
__device_release_driver+0x314/0x5fc
device_release_driver+0x30/0x44
bus_remove_device+0x244/0x490
device_del+0x350/0x900
device_unregister+0x28/0xd0
i2c_unregister_device+0x174/0x1d0
v4l2_device_unregister+0x224/0x380
em28xx_v4l2_init+0x1d90/0x3770
The buggy address belongs to the object at ffff8000d7ca2000
which belongs to the cache kmalloc-2k of size 2048
The buggy address is located 776 bytes inside of
2048-byte region [ffff8000d7ca2000, ffff8000d7ca2800)
The buggy address belongs to the page:
page:ffff7fe00035f280 count:1 mapcount:0 mapping:ffff8000c001f000 index:0x0
flags: 0x7ff800000000100(slab)
raw: 07ff800000000100 ffff7fe00049d880 0000000300000003 ffff8000c001f000
raw: 0000000000000000 0000000080100010 00000001ffffffff 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffff8000d7ca2200: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
ffff8000d7ca2280: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
>ffff8000d7ca2300: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
^
ffff8000d7ca2380: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
ffff8000d7ca2400: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
==================================================================
[2]
Actually, it is allocated for struct tuner, and dvb_frontend is inside.
Signed-off-by: Chi Zhiling <chizhiling@kylinos.cn>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9e3d55fbd160b3ca376599a68b4cddfdc67d4153 ]
The bandwidth fixup quirk doesn't know that SuperSpeed exists and has
the same 8 service intervals per millisecond as High Speed, hence its
calculations are wrong.
Assume that all speeds from HS up use 8 intervals per millisecond.
No further changes are needed, updated code has been confirmed to work
with all speeds from FS to SS.
Signed-off-by: Michal Pecio <michal.pecio@gmail.com>
Reviewed-by: Ricardo Ribalda <ribalda@chromium.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/20240414190040.2255a0bc@foxbook
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5cd7c25f6f0576073b3d03bc4cfb1e8ca63a1195 ]
Some SunplusIT cameras took a borderline interpretation of the UVC 1.5
standard, and fill the PTS and SCR fields with invalid data if the
package does not contain data.
"STC must be captured when the first video data of a video frame is put
on the USB bus."
Some SunplusIT devices send, e.g.,
buffer: 0xa7755c00 len 000012 header:0x8c stc 00000000 sof 0000 pts 00000000
buffer: 0xa7755c00 len 000012 header:0x8c stc 00000000 sof 0000 pts 00000000
buffer: 0xa7755c00 len 000668 header:0x8c stc 73779dba sof 070c pts 7376d37a
While the UVC specification meant that the first two packets shouldn't
have had the SCR bit set in the header.
This borderline/buggy interpretation has been implemented in a variety
of devices, from directly SunplusIT and from other OEMs that rebrand
SunplusIT products. So quirking based on VID:PID will be problematic.
All the affected modules have the following extension unit:
VideoControl Interface Descriptor:
guidExtensionCode {82066163-7050-ab49-b8cc-b3855e8d221d}
But the vendor plans to use that GUID in the future and fix the bug,
this means that we should use heuristic to figure out the broken
packets.
This patch takes care of this.
lsusb of one of the affected cameras:
Bus 001 Device 003: ID 1bcf:2a01 Sunplus Innovation Technology Inc.
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.01
bDeviceClass 239 Miscellaneous Device
bDeviceSubClass 2 ?
bDeviceProtocol 1 Interface Association
bMaxPacketSize0 64
idVendor 0x1bcf Sunplus Innovation Technology Inc.
idProduct 0x2a01
bcdDevice 0.02
iManufacturer 1 SunplusIT Inc
iProduct 2 HanChen Wise Camera
iSerial 3 01.00.00
bNumConfigurations 1
Tested-by: HungNien Chen <hn.chen@sunplusit.com>
Reviewed-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Link: https://lore.kernel.org/r/20240323-resend-hwtimestamp-v10-2-b08e590d97c7@chromium.org
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 38e6f715b02b572f74677eb2f29d3b4bc6f1ddff ]
This commit adds a null check for the 'afb' variable in the
amdgpu_dm_plane_handle_cursor_update function. Previously, 'afb' was
assumed to be null, but was used later in the code without a null check.
This could potentially lead to a null pointer dereference.
Fixes the below:
drivers/gpu/drm/amd/amdgpu/../display/amdgpu_dm/amdgpu_dm_plane.c:1298 amdgpu_dm_plane_handle_cursor_update() error: we previously assumed 'afb' could be null (see line 1252)
Cc: Tom Chung <chiahsuan.chung@amd.com>
Cc: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Cc: Roman Li <roman.li@amd.com>
Cc: Hersen Wu <hersenxs.wu@amd.com>
Cc: Alex Hung <alex.hung@amd.com>
Cc: Aurabindo Pillai <aurabindo.pillai@amd.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 065927b51eb1f042c3e026cebfd55e72ccc26093 ]
There is no need to add a lock in s_ctrl callback, it has been
synchronized by the ctrl_handler's lock, otherwise it may led to
a deadlock if the driver calls v4l2_ctrl_s_ctrl().
Signed-off-by: Ming Qian <ming.qian@nxp.com>
Signed-off-by: Sebastian Fricke <sebastian.fricke@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e864180ee49b4d30e640fd1e1d852b86411420c9 ]
flush_gpu_tlb may be called from another thread while
device_gpu_recover is running.
Both of these threads access registers through the VF
RLCG interface during VF Full Access. Add a lock around this interface
to prevent race conditions between these threads.
Signed-off-by: Victor Skvortsov <victor.skvortsov@amd.com>
Reviewed-by: Zhigang Luo <zhigang.luo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c02c1960c93eede587576625a1221205a68a904f ]
optimize the code to avoid pass a null pointer (hwmgr->backend)
to function smu7_update_edc_leakage_table.
Signed-off-by: Ma Jun <Jun.Ma2@amd.com>
Reviewed-by: Yang Wang <kevinyang.wang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f683f24093dd94a831085fe0ea8e9dc4c6c1a2d1 ]
Function .set_power_profile_mode need an array as input
parameter. So define variable workload as an array to fix
the below coverity warning.
"Passing &workload to function hwmgr->hwmgr_func->set_power_profile_mode
which uses it as an array. This might corrupt or misinterpret adjacent
memory locations"
Signed-off-by: Ma Jun <Jun.Ma2@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 320d8dc612660da84c3b70a28658bb38069e5a9a ]
If we failed to link a free space entry because there's already a
conflicting entry for the same offset, we free the free space entry but
we don't free the associated bitmap that we had just allocated before.
Fix that by freeing the bitmap before freeing the entry.
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3a0a88fcbaf9e027ecca3fe8775be9700b4d6460 ]
This patch updates the workaround for a problem similar to erratum
DS80000789E 6 of the mcp2518fd, the other variants of the chip
family (mcp2517fd and mcp251863) are probably also affected.
Erratum DS80000789E 6 says "reading of the FIFOCI bits in the FIFOSTA
register for an RX FIFO may be corrupted". However observation shows
that this problem is not limited to RX FIFOs but also effects the TEF
FIFO.
In the bad case, the driver reads a too large head index. As the FIFO
is implemented as a ring buffer, this results in re-handling old CAN
transmit complete events.
Every transmit complete event contains with a sequence number that
equals to the sequence number of the corresponding TX request. This
way old TX complete events can be detected.
If the original driver detects a non matching sequence number, it
prints an info message and tries again later. As wrong sequence
numbers can be explained by the erratum DS80000789E 6, demote the info
message to debug level, streamline the code and update the comments.
Keep the behavior: If an old CAN TX complete event is detected, abort
the iteration and mark the number of valid CAN TX complete events as
processed in the chip by incrementing the FIFO's tail index.
Cc: Stefan Althöfer <Stefan.Althoefer@janztec.com>
Cc: Thomas Kopp <thomas.kopp@microchip.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b8e0ddd36ce9536ad7478dd27df06c9ae92370ba ]
This is a preparatory patch to work around a problem similar to
erratum DS80000789E 6 of the mcp2518fd, the other variants of the chip
family (mcp2517fd and mcp251863) are probably also affected.
Erratum DS80000789E 6 says "reading of the FIFOCI bits in the FIFOSTA
register for an RX FIFO may be corrupted". However observation shows
that this problem is not limited to RX FIFOs but also effects the TEF
FIFO.
When handling the TEF interrupt, the driver reads the FIFO header
index from the TEF FIFO STA register of the chip.
In the bad case, the driver reads a too large head index. In the
original code, the driver always trusted the read value, which caused
old CAN transmit complete events that were already processed to be
re-processed.
Instead of reading and trusting the head index, read the head index
and calculate the number of CAN frames that were supposedly received -
replace mcp251xfd_tef_ring_update() with mcp251xfd_get_tef_len().
The mcp251xfd_handle_tefif() function reads the CAN transmit complete
events from the chip, iterates over them and pushes them into the
network stack. The original driver already contains code to detect old
CAN transmit complete events, that will be updated in the next patch.
Cc: Stefan Althöfer <Stefan.Althoefer@janztec.com>
Cc: Thomas Kopp <thomas.kopp@microchip.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 56e69e59751d20993f243fb7dd6991c4e522424c ]
An overflow may occur if the function is called with the last
block and an offset greater than zero. It is necessary to add
a check to avoid this.
Found by Linux Verification Center (linuxtesting.org) with Svace.
[JK: Make test cover also unalloc table freeing]
Link: https://patch.msgid.link/20240620072413.7448-1-r.smirnov@omp.ru
Suggested-by: Jan Kara <jack@suse.com>
Signed-off-by: Roman Smirnov <r.smirnov@omp.ru>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1ca27e0c8c13ac50a4acf9cdf77069e2d94a547d ]
When a SOCK_(STREAM|SEQPACKET) socket connect()s to another one, we need
to lock the two sockets to check their states in unix_stream_connect().
We use unix_state_lock() for the server and unix_state_lock_nested() for
client with tricky sk->sk_state check to avoid deadlock.
The possible deadlock scenario are the following:
1) Self connect()
2) Simultaneous connect()
The former is simple, attempt to grab the same lock, and the latter is
AB-BA deadlock.
After the server's unix_state_lock(), we check the server socket's state,
and if it's not TCP_LISTEN, connect() fails with -EINVAL.
Then, we avoid the former deadlock by checking the client's state before
unix_state_lock_nested(). If its state is not TCP_LISTEN, we can make
sure that the client and the server are not identical based on the state.
Also, the latter deadlock can be avoided in the same way. Due to the
server sk->sk_state requirement, AB-BA deadlock could happen only with
TCP_LISTEN sockets. So, if the client's state is TCP_LISTEN, we can
give up the second lock to avoid the deadlock.
CPU 1 CPU 2 CPU 3
connect(A -> B) connect(B -> A) listen(A)
--- --- ---
unix_state_lock(B)
B->sk_state == TCP_LISTEN
READ_ONCE(A->sk_state) == TCP_CLOSE
^^^^^^^^^
ok, will lock A unix_state_lock(A)
.--------------' WRITE_ONCE(A->sk_state, TCP_LISTEN)
| unix_state_unlock(A)
|
| unix_state_lock(A)
| A->sk_sk_state == TCP_LISTEN
| READ_ONCE(B->sk_state) == TCP_LISTEN
v ^^^^^^^^^^
unix_state_lock_nested(A) Don't lock B !!
Currently, while checking the client's state, we also check if it's
TCP_ESTABLISHED, but this is unlikely and can be checked after we know
the state is not TCP_CLOSE.
Moreover, if it happens after the second lock, we now jump to the restart
label, but it's unlikely that the server is not found during the retry,
so the jump is mostly to revist the client state check.
Let's remove the retry logic and check the state against TCP_CLOSE first.
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fba8334721e266f92079632598e46e5f89082f30 ]
When all the strides in a WQE have been consumed, the WQE is unlinked
from the WQ linked list (mlx5_wq_ll_pop()). For SHAMPO, it is possible
to receive CQEs with 0 consumed strides for the same WQE even after the
WQE is fully consumed and unlinked. This triggers an additional unlink
for the same wqe which corrupts the linked list.
Fix this scenario by accepting 0 sized consumed strides without
unlinking the WQE again.
Signed-off-by: Dragos Tatulea <dtatulea@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://lore.kernel.org/r/20240603212219.1037656-4-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6bad28cfc30988a845fb3f59a99f4b8a4ce8fe95 ]
Let the power supply core register the attribute.
This ensures that the attribute is created before the device is
announced to userspace, avoiding a race condition.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a231eed10ed5a290129fda36ad7bcc263c53ff7d ]
Let the power supply core register the attribute.
This ensures that the attribute is created before the device is
announced to userspace, avoid a race condition.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit db19d3aa77612983a02bd223b3f273f896b243cf ]
There is a race condition in the CMT interrupt handler. In the interrupt
handler the driver sets a driver private flag, FLAG_IRQCONTEXT. This
flag is used to indicate any call to set_next_event() should not be
directly propagated to the device, but instead cached. This is done as
the interrupt handler itself reprograms the device when needed before it
completes and this avoids this operation to take place twice.
It is unclear why this design was chosen, my suspicion is to allow the
struct clock_event_device.event_handler callback, which is called while
the FLAG_IRQCONTEXT is set, can update the next event without having to
write to the device twice.
Unfortunately there is a race between when the FLAG_IRQCONTEXT flag is
set and later cleared where the interrupt handler have already started to
write the next event to the device. If set_next_event() is called in
this window the value is only cached in the driver but not written. This
leads to the board to misbehave, or worse lockup and produce a splat.
rcu: INFO: rcu_preempt detected stalls on CPUs/tasks:
rcu: 0-...!: (0 ticks this GP) idle=f5e0/0/0x0 softirq=519/519 fqs=0 (false positive?)
rcu: (detected by 1, t=6502 jiffies, g=-595, q=77 ncpus=2)
Sending NMI from CPU 1 to CPUs 0:
NMI backtrace for cpu 0
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 6.10.0-rc5-arm64-renesas-00019-g74a6f86eaf1c-dirty #20
Hardware name: Renesas Salvator-X 2nd version board based on r8a77965 (DT)
pstate: 60000005 (nZCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : tick_check_broadcast_expired+0xc/0x40
lr : cpu_idle_poll.isra.0+0x8c/0x168
sp : ffff800081c63d70
x29: ffff800081c63d70 x28: 00000000580000c8 x27: 00000000bfee5610
x26: 0000000000000027 x25: 0000000000000000 x24: 0000000000000000
x23: ffff00007fbb9100 x22: ffff8000818f1008 x21: ffff8000800ef07c
x20: ffff800081c79ec0 x19: ffff800081c70c28 x18: 0000000000000000
x17: 0000000000000000 x16: 0000000000000000 x15: 0000ffffc2c717d8
x14: 0000000000000000 x13: ffff000009c18080 x12: ffff8000825f7fc0
x11: 0000000000000000 x10: ffff8000818f3cd4 x9 : 0000000000000028
x8 : ffff800081c79ec0 x7 : ffff800081c73000 x6 : 0000000000000000
x5 : 0000000000000000 x4 : ffff7ffffe286000 x3 : 0000000000000000
x2 : ffff7ffffe286000 x1 : ffff800082972900 x0 : ffff8000818f1008
Call trace:
tick_check_broadcast_expired+0xc/0x40
do_idle+0x9c/0x280
cpu_startup_entry+0x34/0x40
kernel_init+0x0/0x11c
do_one_initcall+0x0/0x260
__primary_switched+0x80/0x88
rcu: rcu_preempt kthread timer wakeup didn't happen for 6501 jiffies! g-595 f0x0 RCU_GP_WAIT_FQS(5) ->state=0x402
rcu: Possible timer handling issue on cpu=0 timer-softirq=262
rcu: rcu_preempt kthread starved for 6502 jiffies! g-595 f0x0 RCU_GP_WAIT_FQS(5) ->state=0x402 ->cpu=0
rcu: Unless rcu_preempt kthread gets sufficient CPU time, OOM is now expected behavior.
rcu: RCU grace-period kthread stack dump:
task:rcu_preempt state:I stack:0 pid:15 tgid:15 ppid:2 flags:0x00000008
Call trace:
__switch_to+0xbc/0x100
__schedule+0x358/0xbe0
schedule+0x48/0x148
schedule_timeout+0xc4/0x138
rcu_gp_fqs_loop+0x12c/0x764
rcu_gp_kthread+0x208/0x298
kthread+0x10c/0x110
ret_from_fork+0x10/0x20
The design have been part of the driver since it was first merged in
early 2009. It becomes increasingly harder to trigger the issue the
older kernel version one tries. It only takes a few boots on v6.10-rc5,
while hundreds of boots are needed to trigger it on v5.10.
Close the race condition by using the CMT channel lock for the two
competing sections. The channel lock was added to the driver after its
initial design.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20240702190230.3825292-1-niklas.soderlund+renesas@ragnatech.se
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 55d4669ef1b76823083caecfab12a8bd2ccdcf64 ]
When rcu_barrier() calls rcu_rdp_cpu_online() and observes a CPU off
rnp->qsmaskinitnext, it means that all accesses from the offline CPU
preceding the CPUHP_TEARDOWN_CPU are visible to RCU barrier, including
callbacks expiration and counter updates.
However interrupts can still fire after stop_machine() re-enables
interrupts and before rcutree_report_cpu_dead(). The related accesses
happening between CPUHP_TEARDOWN_CPU and rnp->qsmaskinitnext clearing
are _NOT_ guaranteed to be seen by rcu_barrier() without proper
ordering, especially when callbacks are invoked there to the end, making
rcutree_migrate_callback() bypass barrier_lock.
The following theoretical race example can make rcu_barrier() hang:
CPU 0 CPU 1
----- -----
//cpu_down()
smpboot_park_threads()
//ksoftirqd is parked now
<IRQ>
rcu_sched_clock_irq()
invoke_rcu_core()
do_softirq()
rcu_core()
rcu_do_batch()
// callback storm
// rcu_do_batch() returns
// before completing all
// of them
// do_softirq also returns early because of
// timeout. It defers to ksoftirqd but
// it's parked
</IRQ>
stop_machine()
take_cpu_down()
rcu_barrier()
spin_lock(barrier_lock)
// observes rcu_segcblist_n_cbs(&rdp->cblist) != 0
<IRQ>
do_softirq()
rcu_core()
rcu_do_batch()
//completes all pending callbacks
//smp_mb() implied _after_ callback number dec
</IRQ>
rcutree_report_cpu_dead()
rnp->qsmaskinitnext &= ~rdp->grpmask;
rcutree_migrate_callback()
// no callback, early return without locking
// barrier_lock
//observes !rcu_rdp_cpu_online(rdp)
rcu_barrier_entrain()
rcu_segcblist_entrain()
// Observe rcu_segcblist_n_cbs(rsclp) == 0
// because no barrier between reading
// rnp->qsmaskinitnext and rsclp->len
rcu_segcblist_add_len()
smp_mb__before_atomic()
// will now observe the 0 count and empty
// list, but too late, we enqueue regardless
WRITE_ONCE(rsclp->len, rsclp->len + v);
// ignored barrier callback
// rcu barrier stall...
This could be solved with a read memory barrier, enforcing the message
passing between rnp->qsmaskinitnext and rsclp->len, matching the full
memory barrier after rsclp->len addition in rcu_segcblist_add_len()
performed at the end of rcu_do_batch().
However the rcu_barrier() is complicated enough and probably doesn't
need too many more subtleties. CPU down is a slowpath and the
barrier_lock seldom contended. Solve the issue with unconditionally
locking the barrier_lock on rcutree_migrate_callbacks(). This makes sure
that either rcu_barrier() sees the empty queue or its entrained
callback will be migrated.
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cf546dd289e0f6d2594c25e2fb4e19ee67c6d988 ]
If we allocate a bio that is larger than NVMe maximum request size,
attach integrity metadata to it and send it to the NVMe subsystem, the
integrity metadata will be corrupted.
Splitting the bio works correctly. The function bio_split will clone the
bio, trim the iterator of the first bio and advance the iterator of the
second bio.
However, the function rq_integrity_vec has a bug - it returns the first
vector of the bio's metadata and completely disregards the metadata
iterator that was advanced when the bio was split. Thus, the second bio
uses the same metadata as the first bio and this leads to metadata
corruption.
This commit changes rq_integrity_vec, so that it calls mp_bvec_iter_bvec
instead of returning the first vector. mp_bvec_iter_bvec reads the
iterator and uses it to build a bvec for the current position in the
iterator.
The "queue_max_integrity_segments(rq->q) > 1" check was removed, because
the updated rq_integrity_vec function works correctly with multiple
segments.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Reviewed-by: Anuj Gupta <anuj20.g@samsung.com>
Reviewed-by: Kanchan Joshi <joshi.k@samsung.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/49d1afaa-f934-6ed2-a678-e0d428c63a65@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 305a5170dc5cf3d395bb4c4e9239bca6d0b54b49 ]
Currently, mdadm support --revert-reshape to abort the reshape while
reassembling, as the test 07revert-grow. However, following BUG_ON()
can be triggerred by the test:
kernel BUG at drivers/md/raid5.c:6278!
invalid opcode: 0000 [#1] PREEMPT SMP PTI
irq event stamp: 158985
CPU: 6 PID: 891 Comm: md0_reshape Not tainted 6.9.0-03335-g7592a0b0049a #94
RIP: 0010:reshape_request+0x3f1/0xe60
Call Trace:
<TASK>
raid5_sync_request+0x43d/0x550
md_do_sync+0xb7a/0x2110
md_thread+0x294/0x2b0
kthread+0x147/0x1c0
ret_from_fork+0x59/0x70
ret_from_fork_asm+0x1a/0x30
</TASK>
Root cause is that --revert-reshape update the raid_disks from 5 to 4,
while reshape position is still set, and after reassembling the array,
reshape position will be read from super block, then during reshape the
checking of 'writepos' that is caculated by old reshape position will
fail.
Fix this panic the easy way first, by converting the BUG_ON() to
WARN_ON(), and stop the reshape if checkings fail.
Noted that mdadm must fix --revert-shape as well, and probably md/raid
should enhance metadata validation as well, however this means
reassemble will fail and there must be user tools to fix the wrong
metadata.
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Signed-off-by: Song Liu <song@kernel.org>
Link: https://lore.kernel.org/r/20240611132251.1967786-13-yukuai1@huaweicloud.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a8768a134518e406d41799a3594aeb74e0889cf7 ]
The deletion of safemode_timer in mddev_suspend() is redundant and
potentially harmful now. If timer is about to be woken up but gets
deleted, 'in_sync' will remain 0 until the next write, causing array
to stay in the 'active' state instead of transitioning to 'clean'.
Commit 0d9f4f135e ("MD: Add del_timer_sync to mddev_suspend (fix
nasty panic))" introduced this deletion for dm, because if timer fired
after dm is destroyed, the resource which the timer depends on might
have been freed.
However, commit 0dd84b3193 ("md: call __md_stop_writes in md_stop")
added __md_stop_writes() to md_stop(), which is called before freeing
resource. Timer is deleted in __md_stop_writes(), and the origin issue
is resolved. Therefore, delete safemode_timer can be removed safely now.
Signed-off-by: Li Nan <linan122@huawei.com>
Reviewed-by: Yu Kuai <yukuai3@huawei.com>
Signed-off-by: Song Liu <song@kernel.org>
Link: https://lore.kernel.org/r/20240508092053.1447930-1-linan666@huaweicloud.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6040072f4774a575fa67b912efe7722874be337b ]
On powerpc systems, spinlock acquisition does not order prior stores
against later loads. This means that this statement:
rfcp->rfc_next = NULL;
Can be reordered to follow this statement:
WRITE_ONCE(*rfcpp, rfcp);
Which is then a data race with rcu_torture_fwd_prog_cr(), specifically,
this statement:
rfcpn = READ_ONCE(rfcp->rfc_next)
KCSAN located this data race, which represents a real failure on powerpc.
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Acked-by: Marco Elver <elver@google.com>
Cc: Andrey Konovalov <andreyknvl@gmail.com>
Cc: <kasan-dev@googlegroups.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e3862093ee93fcfbdadcb7957f5f8974fffa806a ]
bcm_sf2_mdio_register() calls of_phy_find_device() and then
phy_device_remove() in a loop to remove existing PHY devices.
of_phy_find_device() eventually calls bus_find_device(), which calls
get_device() on the returned struct device * to increment the refcount.
The current implementation does not decrement the refcount, which causes
memory leak.
This commit adds the missing phy_device_free() call to decrement the
refcount via put_device() to balance the refcount.
Fixes: 771089c2a4 ("net: dsa: bcm_sf2: Ensure that MDIO diversion is used")
Signed-off-by: Joe Hattori <joe@pf.is.s.u-tokyo.ac.jp>
Tested-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20240806011327.3817861-1-joe@pf.is.s.u-tokyo.ac.jp
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b5431dc2803ac159d6d4645ae237d15c3cb252db ]
This restores behaviour (including the comment) from now-removed
hci_request.c, and also matches existing code for active scanning.
Without this, the duplicates filter is always active when passive
scanning, which makes it impossible to work with devices that send
nontrivial dynamic data in their advertisement reports.
Fixes: abfeea476c ("Bluetooth: hci_sync: Convert MGMT_OP_START_DISCOVERY")
Signed-off-by: Anton Khirnov <anton@khirnov.net>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 92c4ee25208d0f35dafc3213cdf355fbe449e078 ]
syzbot hit a use-after-free[1] which is caused because the bridge doesn't
make sure that all previous garbage has been collected when removing a
port. What happens is:
CPU 1 CPU 2
start gc cycle remove port
acquire gc lock first
wait for lock
call br_multicasg_gc() directly
acquire lock now but free port
the port can be freed
while grp timers still
running
Make sure all previous gc cycles have finished by using flush_work before
freeing the port.
[1]
BUG: KASAN: slab-use-after-free in br_multicast_port_group_expired+0x4c0/0x550 net/bridge/br_multicast.c:861
Read of size 8 at addr ffff888071d6d000 by task syz.5.1232/9699
CPU: 1 PID: 9699 Comm: syz.5.1232 Not tainted 6.10.0-rc5-syzkaller-00021-g24ca36a562d6 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 06/07/2024
Call Trace:
<IRQ>
__dump_stack lib/dump_stack.c:88 [inline]
dump_stack_lvl+0x116/0x1f0 lib/dump_stack.c:114
print_address_description mm/kasan/report.c:377 [inline]
print_report+0xc3/0x620 mm/kasan/report.c:488
kasan_report+0xd9/0x110 mm/kasan/report.c:601
br_multicast_port_group_expired+0x4c0/0x550 net/bridge/br_multicast.c:861
call_timer_fn+0x1a3/0x610 kernel/time/timer.c:1792
expire_timers kernel/time/timer.c:1843 [inline]
__run_timers+0x74b/0xaf0 kernel/time/timer.c:2417
__run_timer_base kernel/time/timer.c:2428 [inline]
__run_timer_base kernel/time/timer.c:2421 [inline]
run_timer_base+0x111/0x190 kernel/time/timer.c:2437
Reported-by: syzbot+263426984509be19c9a0@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=263426984509be19c9a0
Fixes: e12cec65b5 ("net: bridge: mcast: destroy all entries via gc")
Signed-off-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://patch.msgid.link/20240802080730.3206303-1-razor@blackwall.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
