[ Upstream commit 66e29fcda1 ]
With idle polling, IPIs are not sent when a CPU idle, but queued
and run later from do_idle(). The default kgdb_call_nmi_hook()
implementation gets the pointer to struct pt_regs from get_irq_reqs(),
which doesn't work in that case because it was not called from the
IPI interrupt handler. Fix it by defining our own kgdb_roundup()
function which sents an IPI_ENTER_KGDB. When that IPI is received
on the target CPU kgdb_nmicallback() is called.
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8e0ba125c2 ]
With 64 bit kernels unwind_special() is not working because
it compares the pc to the address of the function descriptor.
Add a helper function that compares pc with the dereferenced
address. This fixes all of the backtraces on my c8000. Without
this changes, a lot of backtraces are missing in kdb or the
show-all-tasks command from /proc/sysrq-trigger.
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9cc2fa4f4a ]
The function end_of_stack() returns a pointer to the last entry of a
stack. For architectures like parisc where the stack grows upwards
return the pointer to the highest address in the stack.
Without this change I faced a crash on parisc, because the stackleak
functionality wrote STACKLEAK_POISON to the lowest address and thus
overwrote the first 4 bytes of the task_struct which included the
TIF_FLAGS.
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 285f68afa8 ]
The following issue is observed with CONFIG_DEBUG_PREEMPT when KVM loads:
KVM: vmx: using Hyper-V Enlightened VMCS
BUG: using smp_processor_id() in preemptible [00000000] code: systemd-udevd/488
caller is set_hv_tscchange_cb+0x16/0x80
CPU: 1 PID: 488 Comm: systemd-udevd Not tainted 5.15.0-rc5+ #396
Hardware name: Microsoft Corporation Virtual Machine/Virtual Machine, BIOS Hyper-V UEFI Release v4.0 12/17/2019
Call Trace:
dump_stack_lvl+0x6a/0x9a
check_preemption_disabled+0xde/0xe0
? kvm_gen_update_masterclock+0xd0/0xd0 [kvm]
set_hv_tscchange_cb+0x16/0x80
kvm_arch_init+0x23f/0x290 [kvm]
kvm_init+0x30/0x310 [kvm]
vmx_init+0xaf/0x134 [kvm_intel]
...
set_hv_tscchange_cb() can get preempted in between acquiring
smp_processor_id() and writing to HV_X64_MSR_REENLIGHTENMENT_CONTROL. This
is not an issue by itself: HV_X64_MSR_REENLIGHTENMENT_CONTROL is a
partition-wide MSR and it doesn't matter which particular CPU will be
used to receive reenlightenment notifications. The only real problem can
(in theory) be observed if the CPU whose id was acquired with
smp_processor_id() goes offline before we manage to write to the MSR,
the logic in hv_cpu_die() won't be able to reassign it correctly.
Reported-by: Michael Kelley <mikelley@microsoft.com>
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Link: https://lore.kernel.org/r/20211012155005.1613352-1-vkuznets@redhat.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8ef9dc0f14 ]
We got the following lockdep splat while running fstests (specifically
btrfs/003 and btrfs/020 in a row) with the new rc. This was uncovered
by 87579e9b7d ("loop: use worker per cgroup instead of kworker") which
converted loop to using workqueues, which comes with lockdep
annotations that don't exist with kworkers. The lockdep splat is as
follows:
WARNING: possible circular locking dependency detected
5.14.0-rc2-custom+ #34 Not tainted
------------------------------------------------------
losetup/156417 is trying to acquire lock:
ffff9c7645b02d38 ((wq_completion)loop0){+.+.}-{0:0}, at: flush_workqueue+0x84/0x600
but task is already holding lock:
ffff9c7647395468 (&lo->lo_mutex){+.+.}-{3:3}, at: __loop_clr_fd+0x41/0x650 [loop]
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #5 (&lo->lo_mutex){+.+.}-{3:3}:
__mutex_lock+0xba/0x7c0
lo_open+0x28/0x60 [loop]
blkdev_get_whole+0x28/0xf0
blkdev_get_by_dev.part.0+0x168/0x3c0
blkdev_open+0xd2/0xe0
do_dentry_open+0x163/0x3a0
path_openat+0x74d/0xa40
do_filp_open+0x9c/0x140
do_sys_openat2+0xb1/0x170
__x64_sys_openat+0x54/0x90
do_syscall_64+0x3b/0x90
entry_SYSCALL_64_after_hwframe+0x44/0xae
-> #4 (&disk->open_mutex){+.+.}-{3:3}:
__mutex_lock+0xba/0x7c0
blkdev_get_by_dev.part.0+0xd1/0x3c0
blkdev_get_by_path+0xc0/0xd0
btrfs_scan_one_device+0x52/0x1f0 [btrfs]
btrfs_control_ioctl+0xac/0x170 [btrfs]
__x64_sys_ioctl+0x83/0xb0
do_syscall_64+0x3b/0x90
entry_SYSCALL_64_after_hwframe+0x44/0xae
-> #3 (uuid_mutex){+.+.}-{3:3}:
__mutex_lock+0xba/0x7c0
btrfs_rm_device+0x48/0x6a0 [btrfs]
btrfs_ioctl+0x2d1c/0x3110 [btrfs]
__x64_sys_ioctl+0x83/0xb0
do_syscall_64+0x3b/0x90
entry_SYSCALL_64_after_hwframe+0x44/0xae
-> #2 (sb_writers#11){.+.+}-{0:0}:
lo_write_bvec+0x112/0x290 [loop]
loop_process_work+0x25f/0xcb0 [loop]
process_one_work+0x28f/0x5d0
worker_thread+0x55/0x3c0
kthread+0x140/0x170
ret_from_fork+0x22/0x30
-> #1 ((work_completion)(&lo->rootcg_work)){+.+.}-{0:0}:
process_one_work+0x266/0x5d0
worker_thread+0x55/0x3c0
kthread+0x140/0x170
ret_from_fork+0x22/0x30
-> #0 ((wq_completion)loop0){+.+.}-{0:0}:
__lock_acquire+0x1130/0x1dc0
lock_acquire+0xf5/0x320
flush_workqueue+0xae/0x600
drain_workqueue+0xa0/0x110
destroy_workqueue+0x36/0x250
__loop_clr_fd+0x9a/0x650 [loop]
lo_ioctl+0x29d/0x780 [loop]
block_ioctl+0x3f/0x50
__x64_sys_ioctl+0x83/0xb0
do_syscall_64+0x3b/0x90
entry_SYSCALL_64_after_hwframe+0x44/0xae
other info that might help us debug this:
Chain exists of:
(wq_completion)loop0 --> &disk->open_mutex --> &lo->lo_mutex
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&lo->lo_mutex);
lock(&disk->open_mutex);
lock(&lo->lo_mutex);
lock((wq_completion)loop0);
*** DEADLOCK ***
1 lock held by losetup/156417:
#0: ffff9c7647395468 (&lo->lo_mutex){+.+.}-{3:3}, at: __loop_clr_fd+0x41/0x650 [loop]
stack backtrace:
CPU: 8 PID: 156417 Comm: losetup Not tainted 5.14.0-rc2-custom+ #34
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 0.0.0 02/06/2015
Call Trace:
dump_stack_lvl+0x57/0x72
check_noncircular+0x10a/0x120
__lock_acquire+0x1130/0x1dc0
lock_acquire+0xf5/0x320
? flush_workqueue+0x84/0x600
flush_workqueue+0xae/0x600
? flush_workqueue+0x84/0x600
drain_workqueue+0xa0/0x110
destroy_workqueue+0x36/0x250
__loop_clr_fd+0x9a/0x650 [loop]
lo_ioctl+0x29d/0x780 [loop]
? __lock_acquire+0x3a0/0x1dc0
? update_dl_rq_load_avg+0x152/0x360
? lock_is_held_type+0xa5/0x120
? find_held_lock.constprop.0+0x2b/0x80
block_ioctl+0x3f/0x50
__x64_sys_ioctl+0x83/0xb0
do_syscall_64+0x3b/0x90
entry_SYSCALL_64_after_hwframe+0x44/0xae
RIP: 0033:0x7f645884de6b
Usually the uuid_mutex exists to protect the fs_devices that map
together all of the devices that match a specific uuid. In rm_device
we're messing with the uuid of a device, so it makes sense to protect
that here.
However in doing that it pulls in a whole host of lockdep dependencies,
as we call mnt_may_write() on the sb before we grab the uuid_mutex, thus
we end up with the dependency chain under the uuid_mutex being added
under the normal sb write dependency chain, which causes problems with
loop devices.
We don't need the uuid mutex here however. If we call
btrfs_scan_one_device() before we scratch the super block we will find
the fs_devices and not find the device itself and return EBUSY because
the fs_devices is open. If we call it after the scratch happens it will
not appear to be a valid btrfs file system.
We do not need to worry about other fs_devices modifying operations here
because we're protected by the exclusive operations locking.
So drop the uuid_mutex here in order to fix the lockdep splat.
A more detailed explanation from the discussion:
We are worried about rm and scan racing with each other, before this
change we'll zero the device out under the UUID mutex so when scan does
run it'll make sure that it can go through the whole device scan thing
without rm messing with us.
We aren't worried if the scratch happens first, because the result is we
don't think this is a btrfs device and we bail out.
The only case we are concerned with is we scratch _after_ scan is able
to read the superblock and gets a seemingly valid super block, so lets
consider this case.
Scan will call device_list_add() with the device we're removing. We'll
call find_fsid_with_metadata_uuid() and get our fs_devices for this
UUID. At this point we lock the fs_devices->device_list_mutex. This is
what protects us in this case, but we have two cases here.
1. We aren't to the device removal part of the RM. We found our device,
and device name matches our path, we go down and we set total_devices
to our super number of devices, which doesn't affect anything because
we haven't done the remove yet.
2. We are past the device removal part, which is protected by the
device_list_mutex. Scan doesn't find the device, it goes down and
does the
if (fs_devices->opened)
return -EBUSY;
check and we bail out.
Nothing about this situation is ideal, but the lockdep splat is real,
and the fix is safe, tho admittedly a bit scary looking.
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: David Sterba <dsterba@suse.com>
[ copy more from the discussion ]
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8c9c296adf ]
The VRF driver invokes netfilter for output+postrouting hooks so that users
can create rules that check for 'oif $vrf' rather than lower device name.
This is a problem when NAT rules are configured.
To avoid any conntrack involvement in round 1, tag skbs as 'untracked'
to prevent conntrack from picking them up.
This gets cleared before the packet gets handed to the ip stack so
conntrack will be active on the second iteration.
One remaining issue is that a rule like
output ... oif $vrfname notrack
won't propagate to the second round because we can't tell
'notrack set via ruleset' and 'notrack set by vrf driver' apart.
However, this isn't a regression: the 'notrack' removal happens
instead of unconditional nf_reset_ct().
I'd also like to avoid leaking more vrf specific conditionals into the
netfilter infra.
For ingress, conntrack has already been done before the packet makes it
to the vrf driver, with this patch egress does connection tracking with
lower/physical device as well.
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 345dac33f5 ]
When configuring the kernel for big-endian, we set either BE-8 or BE-32
based on the CPU architecture level. Until linux-4.4, we did not have
any ARMv7-M platform allowing big-endian builds, but now i.MX/Vybrid
is in that category, adn we get a build error because of this:
arch/arm/kernel/module-plts.c: In function 'get_module_plt':
arch/arm/kernel/module-plts.c:60:46: error: implicit declaration of function '__opcode_to_mem_thumb32' [-Werror=implicit-function-declaration]
This comes down to picking the wrong default, ARMv7-M uses BE8
like ARMv7-A does. Changing the default gets the kernel to compile
and presumably works.
https://lore.kernel.org/all/1455804123-2526139-2-git-send-email-arnd@arndb.de/
Tested-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 61e18ce734 ]
When addr_gen_mode is set to IN6_ADDR_GEN_MODE_NONE, the link-local addr
should not be generated. But it isn't the case for GRE (as well as GRE6)
and SIT tunnels. Make it so that tunnels consider the addr_gen_mode,
especially for IN6_ADDR_GEN_MODE_NONE.
Do this in add_v4_addrs() to cover both GRE and SIT only if the addr
scope is link.
Signed-off-by: Stephen Suryaputra <ssuryaextr@gmail.com>
Acked-by: Antonio Quartulli <a@unstable.cc>
Link: https://lore.kernel.org/r/20211020200618.467342-1-ssuryaextr@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b3ea5d56f2 ]
Currently the stacktrace on clang compiled arm kernel uses the 'lr'
register to find the first frame address from pt_regs. However, that
is wrong after calling another function, because the 'lr' register
is used by 'bl' instruction and never be recovered.
As same as gcc arm kernel, directly use the frame pointer (r11) of
the pt_regs to find the first frame address.
Note that this fixes kretprobe stacktrace issue only with
CONFIG_UNWINDER_FRAME_POINTER=y. For the CONFIG_UNWINDER_ARM,
we need another fix.
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c3867ab592 ]
get_warnings_count() does fclose() using File * returned from popen().
Fix it to call pclose() as it should.
tools/testing/selftests/kvm/x86_64/mmio_warning_test
x86_64/mmio_warning_test.c: In function ‘get_warnings_count’:
x86_64/mmio_warning_test.c:87:9: warning: ‘fclose’ called on pointer returned from a mismatched allocation function [-Wmismatched-dealloc]
87 | fclose(f);
| ^~~~~~~~~
x86_64/mmio_warning_test.c:84:13: note: returned from ‘popen’
84 | f = popen("dmesg | grep \"WARNING:\" | wc -l", "r");
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2b81a5f015 ]
When reading the partition table on initial scan hits an I/O error the
I/O will hang with the scan_mutex held:
[<0>] do_read_cache_page+0x49b/0x790
[<0>] read_part_sector+0x39/0xe0
[<0>] read_lba+0xf9/0x1d0
[<0>] efi_partition+0xf1/0x7f0
[<0>] bdev_disk_changed+0x1ee/0x550
[<0>] blkdev_get_whole+0x81/0x90
[<0>] blkdev_get_by_dev+0x128/0x2e0
[<0>] device_add_disk+0x377/0x3c0
[<0>] nvme_mpath_set_live+0x130/0x1b0 [nvme_core]
[<0>] nvme_mpath_add_disk+0x150/0x160 [nvme_core]
[<0>] nvme_alloc_ns+0x417/0x950 [nvme_core]
[<0>] nvme_validate_or_alloc_ns+0xe9/0x1e0 [nvme_core]
[<0>] nvme_scan_work+0x168/0x310 [nvme_core]
[<0>] process_one_work+0x231/0x420
and trying to delete the controller will deadlock as it tries to grab
the scan mutex:
[<0>] nvme_mpath_clear_ctrl_paths+0x25/0x80 [nvme_core]
[<0>] nvme_remove_namespaces+0x31/0xf0 [nvme_core]
[<0>] nvme_do_delete_ctrl+0x4b/0x80 [nvme_core]
As we're now properly ordering the namespace list there is no need to
hold the scan_mutex in nvme_mpath_clear_ctrl_paths() anymore.
And we always need to kick the requeue list as the path will be marked
as unusable and I/O will be requeued _without_ a current path.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2351ead99c ]
When removing a port, all its controllers are being removed, but there
are queues on the port that doesn't belong to any controller (during
connection time). This causes a use-after-free bug for any command
that dereferences req->port (like in nvmet_alloc_ctrl). Those queues
should be destroyed before freeing the port via configfs. Destroy
the remaining queues after the accept_work was cancelled guarantees
that no new queue will be created.
Signed-off-by: Israel Rukshin <israelr@nvidia.com>
Reviewed-by: Max Gurtovoy <mgurtovoy@nvidia.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e3e19dcc4c ]
When a port is removed through configfs, any connected controllers
are starting teardown flow asynchronously and can still send commands.
This causes a use-after-free bug for any command that dereferences
req->port (like in nvmet_parse_io_cmd).
To fix this, wait for all the teardown scheduled works to complete
(like release_work at rdma/tcp drivers). This ensures there are no
active controllers when the port is eventually removed.
Signed-off-by: Israel Rukshin <israelr@nvidia.com>
Reviewed-by: Max Gurtovoy <mgurtovoy@nvidia.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 037057a5a9 ]
This check is meant to catch cases where a requeue is attempted on a
request that is still inserted. It's never really been useful to catch any
misuse, and now it's actively wrong. Outside of that, this should not be a
BUG_ON() to begin with.
Remove the check as it's now causing active harm, as requeue off the plug
path will trigger it even though the request state is just fine.
Reported-by: Yi Zhang <yi.zhang@redhat.com>
Link: https://lore.kernel.org/linux-block/CAHj4cs80zAUc2grnCZ015-2Rvd-=gXRfB_dFKy=RTm+wRo09HQ@mail.gmail.com/
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7ce1bb83a1 ]
If CONFIG_CFI_CLANG=y, attempting to read an event histogram will cause
the kernel to panic due to failed CFI check.
1. echo 'hist:keys=common_pid' >> events/sched/sched_switch/trigger
2. cat events/sched/sched_switch/hist
3. kernel panics on attempting to read hist
This happens because the sort() function expects a generic
int (*)(const void *, const void *) pointer for the compare function.
To prevent this CFI failure, change tracing map cmp_entries_* function
signatures to match this.
Also, fix the build error reported by the kernel test robot [1].
[1] https://lore.kernel.org/r/202110141140.zzi4dRh4-lkp@intel.com/
Link: https://lkml.kernel.org/r/20211014045217.3265162-1-kaleshsingh@google.com
Signed-off-by: Kalesh Singh <kaleshsingh@google.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d25302e465 ]
Some unfriendly component, such as dpdk, write the same mask to
unbound kworker cpumask again and again. Every time it write to
this interface some work is queue to cpu, even though the mask
is same with the original mask.
So, fix it by return success and do nothing if the cpumask is
equal with the old one.
Signed-off-by: Mengen Sun <mengensun@tencent.com>
Signed-off-by: Menglong Dong <imagedong@tencent.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4f8d7abaa4 ]
This might matter, for example, if the underlying type of enum xz_check
was a signed char. In such a case the validation wouldn't have caught an
unsupported header. I don't know if this problem can occur in the kernel
on any arch but it's still good to fix it because some people might copy
the XZ code to their own projects from Linux instead of the upstream
XZ Embedded repository.
This change may increase the code size by a few bytes. An alternative
would have been to use an unsigned int instead of enum xz_check but
using an enumeration looks cleaner.
Link: https://lore.kernel.org/r/20211010213145.17462-3-xiang@kernel.org
Signed-off-by: Lasse Collin <lasse.collin@tukaani.org>
Signed-off-by: Gao Xiang <hsiangkao@linux.alibaba.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 83d3c4f22a ]
With valid files, the safety margin described in lib/decompress_unxz.c
ensures that these buffers cannot overlap. But if the uncompressed size
of the input is larger than the caller thought, which is possible when
the input file is invalid/corrupt, the buffers can overlap. Obviously
the result will then be garbage (and usually the decoder will return
an error too) but no other harm will happen when such an over-run occurs.
This change only affects uncompressed LZMA2 chunks and so this
should have no effect on performance.
Link: https://lore.kernel.org/r/20211010213145.17462-2-xiang@kernel.org
Signed-off-by: Lasse Collin <lasse.collin@tukaani.org>
Signed-off-by: Gao Xiang <hsiangkao@linux.alibaba.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2835f327bd ]
Some buggy firmware and/or brand new batteries can support a charge that's
slightly over the reported design capacity. In such cases, the kernel will
report to userspace that the charging state of the battery is "Unknown",
when in reality the battery charge is "Full", at least from the design
capacity point of view. Make the fallback condition accepts capacities
over the designed capacity so userspace knows that is full.
Signed-off-by: André Almeida <andrealmeid@collabora.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 814a66741b ]
Both iov_iter_get_pages and iov_iter_get_pages_alloc return the number
of bytes of the iovec they could get the pages for. When they cannot
get any pages, they're supposed to return 0, but when the start of the
iovec isn't page aligned, the calculation goes wrong and they return a
negative value. Fix both functions.
In addition, change iov_iter_get_pages_alloc to return NULL in that case
to prevent resource leaks.
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4b6012a783 ]
kzalloc() is used to allocate memory for cd->detectors, and if it fails,
channel_detector_exit() behind the label fail will be called:
channel_detector_exit(dpd, cd);
In channel_detector_exit(), cd->detectors is dereferenced through:
struct pri_detector *de = cd->detectors[i];
To fix this possible null-pointer dereference, check cd->detectors before
the for loop to dereference cd->detectors.
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn>
Signed-off-by: Tuo Li <islituo@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210805153854.154066-1-islituo@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 49d67e4457 ]
The tracefs file system is by default mounted such that only root user can
access it. But there are legitimate reasons to create a group and allow
those added to the group to have access to tracing. By changing the
permissions of the tracefs mount point to allow access, it will allow
group access to the tracefs directory.
There should not be any real reason to allow all access to the tracefs
directory as it contains sensitive information. Have the default
permission of directories being created not have any OTH (other) bits set,
such that an admin that wants to give permission to a group has to first
disable all OTH bits in the file system.
Link: https://lkml.kernel.org/r/20210818153038.664127804@goodmis.org
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 146e5e7333 ]
Due to deadlocks in the networking subsystem spotted 12 years ago[1],
a workaround was put in place[2] to avoid taking the rtnl lock when it
was not available and restarting the syscall (back to VFS, letting
userspace spin). The following construction is found a lot in the net
sysfs and sysctl code:
if (!rtnl_trylock())
return restart_syscall();
This can be problematic when multiple userspace threads use such
interfaces in a short period, making them to spin a lot. This happens
for example when adding and moving virtual interfaces: userspace
programs listening on events, such as systemd-udevd and NetworkManager,
do trigger actions reading files in sysfs. It gets worse when a lot of
virtual interfaces are created concurrently, say when creating
containers at boot time.
Returning early without hitting the above pattern when the syscall will
fail eventually does make things better. While it is not a fix for the
issue, it does ease things.
[1] https://lore.kernel.org/netdev/49A4D5D5.5090602@trash.net/https://lore.kernel.org/netdev/m14oyhis31.fsf@fess.ebiederm.org/
and https://lore.kernel.org/netdev/20090226084924.16cb3e08@nehalam/
[2] Rightfully, those deadlocks are *hard* to solve.
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Reviewed-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ea2b9a3371 ]
bus_info field had a different value for the media entity and the video
device.
Fixes v4l2-compliance:
v4l2-compliance.cpp(637): media bus_info 'PCI:0000:00:05.0' differs from
V4L2 bus_info 'PCI:viewfinder'
Reviewed-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 553481e380 ]
For a try_fmt call, the node noes not need to be enabled.
Fixes v4l2-compliance
fail: v4l2-test-formats.cpp(717): Video Output Multiplanar is valid, but
no TRY_FMT was implemented
test VIDIOC_TRY_FMT: FAIL
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d3c4b6f64a ]
ACPICA commit 0762982923f95eb652cf7ded27356b247c9774de
During wakeup from system-wide sleep states, acpi_get_sleep_type_data()
is called and it tries to get memory from the slab allocator in order
to evaluate a control method, but if KFENCE is enabled in the kernel,
the memory allocation attempt causes an IRQ work to be queued and a
self-IPI to be sent to the CPU running the code which requires the
memory controller to be ready, so if that happens too early in the
wakeup path, it doesn't work.
Prevent that from taking place by calling acpi_get_sleep_type_data()
for S0 upfront, when preparing to enter a given sleep state, and
saving the data obtained by it for later use during system wakeup.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=214271
Reported-by: Reik Keutterling <spielkind@gmail.com>
Tested-by: Reik Keutterling <spielkind@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b36eb5e7b7 ]
Don't do kfree or other risky things when oops_in_progress is set.
It's easy enough to avoid doing them
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fc41665498 ]
If rcsi2_code_to_fmt() return NULL, then null pointer dereference occurs
in the next cycle. That should not be possible now but adding checking
protects from future bugs.
The patch adds checking if format is NULL.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Nadezda Lutovinova <lutovinova@ispras.ru>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 49c3eb3036 ]
The Cyberbook T116 tablet contains quite generic names in the sys_vendor
and product_name DMI strings, without this patch brcmfmac will try to load:
"brcmfmac43455-sdio.Default string-Default string.txt" as nvram file which
is way too generic.
The nvram file shipped on the factory Android image contains the exact
same settings as those used on the AcePC T8 mini PC, so point the new
DMI nvram filename quirk to the acepc-t8 nvram file.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210928160633.96928-1-hdegoede@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c15b5fc054 ]
When CONFIG_PRINTK is not set, the CMPXCHG_BUGCHECK() macro calls
_printk(), but _printk() is a static inline function, not available
as an extern.
Since the purpose of the macro is to print the BUGCHECK info,
make this config option depend on PRINTK.
Fixes multiple occurrences of this build error:
../include/linux/printk.h:208:5: error: static declaration of '_printk' follows non-static declaration
208 | int _printk(const char *s, ...)
| ^~~~~~~
In file included from ../arch/ia64/include/asm/cmpxchg.h:5,
../arch/ia64/include/uapi/asm/cmpxchg.h:146:28: note: previous declaration of '_printk' with type 'int(const char *, ...)'
146 | extern int _printk(const char *fmt, ...);
Cc: linux-ia64@vger.kernel.org
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Chris Down <chris@chrisdown.name>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Petr Mladek <pmladek@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6d0d779b21 ]
Some tools like v4l2-compliance let users select a media device based
on the bus_info string which can be quite convenient. Use a unique
string for that.
This also fixes the following v4l2-compliance warning:
warn: v4l2-test-media.cpp(52): empty bus_info
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cdfaf4752e ]
If of_device_get_match_data() return NULL,
then null pointer dereference occurs in s5p_mfc_init_pm().
The patch adds checking if dev->variant is NULL.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Nadezda Lutovinova <lutovinova@ispras.ru>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8515965e5e ]
The variable pdev is assigned to dev->plat_dev, and dev->plat_dev is
checked in:
if (!dev->plat_dev)
This indicates both dev->plat_dev and pdev can be NULL. If so, the
function dev_err() is called to print error information.
dev_err(&pdev->dev, "No platform data specified\n");
However, &pdev->dev is an illegal address, and it is dereferenced in
dev_err().
To fix this possible null-pointer dereference, replace dev_err() with
mfc_err().
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn>
Signed-off-by: Tuo Li <islituo@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e3f60e7e1a ]
All the entities must have a unique name. We can have a descriptive and
unique name by appending the function and the entity->id.
This is even resilent to multi chain devices.
Fixes v4l2-compliance:
Media Controller ioctls:
fail: v4l2-test-media.cpp(205): v2_entity_names_set.find(key) != v2_entity_names_set.end()
test MEDIA_IOC_G_TOPOLOGY: FAIL
fail: v4l2-test-media.cpp(394): num_data_links != num_links
test MEDIA_IOC_ENUM_ENTITIES/LINKS: FAIL
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ffccdde5f0 ]
The device is doing something unexpected with the control. Either because
the protocol is not properly implemented or there has been a HW error.
Fixes v4l2-compliance:
Control ioctls (Input 0):
fail: v4l2-test-controls.cpp(448): s_ctrl returned an error (22)
test VIDIOC_G/S_CTRL: FAIL
fail: v4l2-test-controls.cpp(698): s_ext_ctrls returned an error (22)
test VIDIOC_G/S/TRY_EXT_CTRLS: FAIL
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 548fa43a58 ]
At the moment of enabling irq handling:
1922 ret = devm_request_threaded_irq(&pdev->dev, irq, dcmi_irq_callback,
1923 dcmi_irq_thread, IRQF_ONESHOT,
1924 dev_name(&pdev->dev), dcmi);
there is still uninitialized field sd_format of struct stm32_dcmi *dcmi.
If an interrupt occurs in the interval between the installation of the
interrupt handler and the initialization of this field, NULL pointer
dereference happens.
This field is dereferenced in the handler function without any check:
457 if (dcmi->sd_format->fourcc == V4L2_PIX_FMT_JPEG &&
458 dcmi->misr & IT_FRAME) {
The patch moves interrupt handler installation
after initialization of the sd_format field that happens in
dcmi_graph_notify_complete() via dcmi_set_default_fmt().
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Dmitriy Ulitin <ulitin@ispras.ru>
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0961ba6dd2 ]
To prevent corrupted frames after starting and stopping the sensor its
datasheet specifies a specific pause sequence to follow:
Stopping:
Set Pause_Restart Bit -> Set Restart Bit -> Set Chip_Enable Off
Restarting:
Set Chip_Enable On -> Clear Pause_Restart Bit
The Restart Bit is cleared automatically and must not be cleared
manually as this would cause undefined behavior.
Signed-off-by: Dirk Bender <d.bender@phytec.de>
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
