commit c88547a811 upstream.
Commit f5ea1100 ("xfs: add CRCs to dir2/da node blocks") introduced
in 3.10 incorrectly converted the btree hash index array pointer in
xfs_da3_fixhashpath(). It resulted in the the current hash always
being compared against the first entry in the btree rather than the
current block index into the btree block's hash entry array. As a
result, it was comparing the wrong hashes, and so could misorder the
entries in the btree.
For most cases, this doesn't cause any problems as it requires hash
collisions to expose the ordering problem. However, when there are
hash collisions within a directory there is a very good probability
that the entries will be ordered incorrectly and that actually
matters when duplicate hashes are placed into or removed from the
btree block hash entry array.
This bug results in an on-disk directory corruption and that results
in directory verifier functions throwing corruption warnings into
the logs. While no data or directory entries are lost, access to
them may be compromised, and attempts to remove entries from a
directory that has suffered from this corruption may result in a
filesystem shutdown. xfs_repair will fix the directory hash
ordering without data loss occuring.
[dchinner: wrote useful a commit message]
Reported-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Mark Tinguely <tinguely@sgi.com>
Reviewed-by: Ben Myers <bpm@sgi.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f764cd68d9 upstream.
Zero-initializing ether_type masked that the ether type would never be
obtained for 8021x packets and the comparison against eapol_type
would always fail.
Reported-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6b355b33a6 upstream.
Previous logic,
if (avail > 8) {
store slave;
return;
}
send data; clear;
The logic error is, if there isn't space send the buffer and clear,
but the slave wasn't added to the now empty buffer loosing that slave
id. It also should have been "if (avail >= 8)" because when it is 8,
there is space.
Instead, if there isn't space send and clear the buffer, then there is
always space for the slave id.
Signed-off-by: David Fries <David@Fries.net>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 483e2dfdbc upstream.
Fixes: 4aab3fadad ("mfd: tps65910: Move interrupt implementation code to mfd file")
tps65910_irq_init() sets 'tps65910->chip_irq' before calling
regmap_add_irq_chip(). If the regmap_add_irq_chip() call fails in
memory allocation of regmap_irq_chip_data members then:
1. The 'tps65910->chip_irq' will still hold some value
2. 'tps65910->irq_data' will be pointing to already freed memory
(because regmap_add_irq_chip() will free it on error)
This results in invalid memory access during driver remove because the
tps65910_irq_exit() tests whether 'tps65910->chip_irq' is not zero.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 97dc4ed3fa upstream.
During probe the driver allocates dummy I2C devices for RTC, haptic and
MUIC with i2c_new_dummy() but it does not check the return value of this
calls.
In case of error (i2c_new_device(): memory allocation failure or I2C
address cannot be used) this function returns NULL which is later used
by i2c_unregister_device().
If i2c_new_dummy() fails for RTC, haptic or MUIC devices, fail also the
probe for main MFD driver.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ed26f87b9f upstream.
During probe the driver allocates dummy I2C device for RTC with i2c_new_dummy() but it does not check the return value of this call.
In case of error (i2c_new_device(): memory allocation failure or I2C
address cannot be used) this function returns NULL which is later used
by i2c_unregister_device().
If i2c_new_dummy() fails for RTC device, fail also the probe for
main MFD driver.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 96cf3dedc4 upstream.
During probe the driver allocates dummy I2C devices for RTC and ADC
with i2c_new_dummy() but it does not check the return value of this
calls.
In case of error (i2c_new_device(): memory allocation failure or I2C
address cannot be used) this function returns NULL which is later used
by i2c_unregister_device().
If i2c_new_dummy() fails for RTC or ADC devices, fail also the probe
for main MFD driver.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ad09dd6a1f upstream.
During probe the driver allocates dummy I2C devices for MUIC and haptic
with i2c_new_dummy() but it does not check the return value of this
calls.
In case of error (i2c_new_device(): memory allocation failure or I2C
address cannot be used) this function returns NULL which is later used
by devm_regmap_init_i2c() and i2c_unregister_device().
If i2c_new_dummy() fails for MUIC or haptic devices, fail also the probe
for main MFD driver.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b9e183a1d4 upstream.
During probe the driver allocates dummy I2C device for RTC with
i2c_new_dummy() but it does not check the return value of this call.
In case of error (i2c_new_device(): memory allocation failure or I2C
address cannot be used) this function returns NULL which is later used
by i2c_unregister_device().
If i2c_new_dummy() fails for RTC device, fail also the probe for main
MFD driver.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a7ab1c8b26 upstream.
During probe the driver allocates dummy I2C device for companion chip
and then allocates a regmap for it. If regmap_init_i2c() fails then the
I2C driver (allocated with i2c_new_dummy()) is not freed and this
resource leaks.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 159ce52a6b upstream.
During probe the driver allocates dummy I2C device for companion chip
with i2c_new_dummy() but it does not check the return value of this call.
In case of error (i2c_new_device(): memory allocation failure or I2C
address cannot be used) this function returns NULL which is later used
by regmap_init_i2c().
If i2c_new_dummy() fails for companion device, fail also the probe for
main MFD driver.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 65aba1e049 upstream.
During probe the sec-core driver allocates dummy I2C device for RTC with
i2c_new_dummy() but return value is not checked. In case of error
(i2c_new_device(): memory allocation failure or I2C address cannot be
used) this function returns NULL which is later used by
devm_regmap_init_i2c() or i2c_unregister_device().
If i2c_new_dummy() fails for RTC device, fail also the probe for main
MFD driver.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5e6533a6f5 upstream.
NM and SPS FW types that may run on ME device on server platforms
do not have valid MEI/HECI interface and driver should not
be bound to it as this might lead to system hung.
In practice not all BIOSes effectively hide such devices from the
OS and in some cases it is not possible.
We determine FW type by examining Host FW status registers in order to
unbind the driver.
In this patch we are adding check for ME on Cougar Point, Lynx Point
Devices
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Tested-by: Nikola Ciprich <nikola.ciprich@linuxbox.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2253e8d792 upstream.
ccw consoles are in use before they can be properly registered with
the driver core. For devices which are in use by a device driver we
rely on the ccw_device's pointer to the driver callbacks to be valid.
For ccw consoles this pointer is NULL until they are registered later
during boot and we dereferenced this pointer. This worked by
chance on 64 bit builds (cdev->drv was NULL but the optional callback
cdev->drv->path_event was also NULL by coincidence) and was unnoticed
until we received reports about boot failures on 31 bit systems.
Fix it by initializing the driver pointer for ccw consoles.
Reported-by: Mike Frysinger <vapier@gentoo.org>
Reported-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Reviewed-by: Peter Oberparleiter <oberpar@linux.vnet.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 415d555e6b upstream.
The recent fixups for HP laptops to support the mute LED made the
speaker output silent on some machines. It turned out that they use
the NID 0x18 for the speaker while it's also used for controlling the
LED via VREF bits although the current driver code blindly assumes
that such a node is a mic pin (where 0x18 is usually so).
This patch fixes the problem by only changing the VREF bits and
keeping the other pin ctl bits.
Reported-and-tested-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4f8e940095 upstream.
PCM pointer callbacks in ice1712 driver check the buffer size boundary
wrongly between bytes and frames. This leads to PCM core warnings
like:
snd_pcm_update_hw_ptr0: 105 callbacks suppressed
ALSA pcm_lib.c:352 BUG: pcmC3D0c:0, pos = 5461, buffer size = 5461, period size = 2730
This patch fixes these checks to be placed after the proper unit
conversions.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 56b700fd6f upstream.
For vmcore generated by LPAE enabled kernel, user space
utility such as crash needs additional infomation to
parse.
So this patch add arch_crash_save_vmcoreinfo as what PAE enabled
i386 linux does.
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Liu Hua <sdu.liu@huawei.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 80bb3ef109 upstream.
In big-endian systems, "%1" get the most significant part of the value, cause the instruction to get the wrong result.
When viewing ftrace record in big-endian ARM systems, we found that
the timestamp errors:
swapper-0 [001] 1325.970000: 0:120:R ==> [001] 16:120:R events/1
events/1-16 [001] 1325.970000: 16:120:S ==> [001] 0:120:R swapper
swapper-0 [000] 1325.1000000: 0:120:R + [000] 15:120:R events/0
swapper-0 [000] 1325.1000000: 0:120:R ==> [000] 15:120:R events/0
swapper-0 [000] 1326.030000: 0:120:R + [000] 1150:120:R sshd
swapper-0 [000] 1326.030000: 0:120:R ==> [000] 1150:120:R sshd
When viewed ftrace records, it will call the do_div(n, base) function, which achieved arch/arm/include/asm/div64.h in. When n = 10000000, base = 1000000, in do_div(n, base) will execute "umull %Q0, %R0, %1, %Q2".
Reviewed-by: Dave Martin <Dave.Martin@arm.com>
Reviewed-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Alex Wu <wuquanming@huawei.com>
Signed-off-by: Xiangyu Lu <luxiangyu@huawei.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b6ccb9803e upstream.
CPU_32v6 currently selects CPU_USE_DOMAINS if CPU_V6 and MMU. This is
because ARM 1136 r0pX CPUs lack the v6k extensions, and therefore do
not have hardware thread registers. The lack of these registers requires
the kernel to update the vectors page at each context switch in order to
write a new TLS pointer. This write must be done via the userspace
mapping, since aliasing caches can lead to expensive flushing when using
kmap. Finally, this requires the vectors page to be mapped r/w for
kernel and r/o for user, which has implications for things like put_user
which must trigger CoW appropriately when targetting user pages.
The upshot of all this is that a v6/v7 kernel makes use of domains to
segregate kernel and user memory accesses. This has the nasty
side-effect of making device mappings executable, which has been
observed to cause subtle bugs on recent cores (e.g. Cortex-A15
performing a speculative instruction fetch from the GIC and acking an
interrupt in the process).
This patch solves this problem by removing the remaining domain support
from ARMv6. A new memory type is added specifically for the vectors page
which allows that page (and only that page) to be mapped as user r/o,
kernel r/w. All other user r/o pages are mapped also as kernel r/o.
Patch co-developed with Russell King.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bfeda82727 upstream.
Apparently, if G3D regulator is powered off, the SoC cannot enter low
power modes and just hangs. This patch fixes this by keeping the
regulator always on when the system is running, as suggested by Exynos 4
User's Manual in case of Exynos4210/4x12 SoCs (Exynos5250 UM does not
have such note, but observed behavior seems to confirm that it is true
for this SoC as well).
This fixes an issue preventing Arndale board from entering sleep mode
observed since commit
346f372f7b clk: exynos5250: Add CLK_IGNORE_UNUSED flag for pmu clock
that landed in kernel 3.10, which has fixed the clock driver to make the
SoC actually try to enter the sleep mode.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Tested-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c6c56697ae upstream.
OMAP3 doesn't contain "l3_init_clkdm" clock domain. Use the
proper clock domains for USB Host and USB TLL modules.
Gets rid of the following warnings during boot
omap_hwmod: usb_host_hs: could not associate to clkdm l3_init_clkdm
omap_hwmod: usb_tll_hs: could not associate to clkdm l3_init_clkdm
Reported-by: Nishanth Menon <nm@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Fixes: de231388cb ("ARM: OMAP: USB: EHCI and OHCI hwmod structures for OMAP3")
Cc: Keshava Munegowda <keshava_mgowda@ti.com>
Cc: Partha Basak <parthab@india.ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 07484ca33e upstream.
Just like IS_PM34XX_ERRATUM, IS_PM44XX_ERRATUM is valid only if
CONFIG_PM is enabled, else, disabling CONFIG_PM results in build
failure complaining about the following:
arch/arm/mach-omap2/built-in.o: In function `omap4_boot_secondary':
:(.text+0x8a70): undefined reference to `pm44xx_errata'
Fixes: c962184 (ARM: OMAP4: PM: add errata support)
Reported-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.ocm>
Acked-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 698b485325 upstream.
When an interrupt has become active on the INTC it will stay active
until it is acked, even if masked or de-asserted. The
INTC_PENDING_IRQn registers are however updated and since these are
used by omap_intc_handle_irq to determine which interrupt to handle,
it will never see the active interrupt. This will result in a storm of
useless interrupts that is only stopped when another higher priority
interrupt is asserted.
Fix by sending the INTC an acknowledge if we find no interrupts to
handle.
Signed-off-by: Stefan Sørensen <stefan.sorensen@spectralink.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7272e05115 upstream.
The shift values for the ADC,PCM, and Analog kcontrols were wrong causing wrong values for the SOC_DOUBLE_R_SX_TLV macros
Fixed the TLV for aout_tlv to show -102dB correctly
Fixes: 1d99f2436d (ASoC: core: Rework SOC_DOUBLE_R_SX_TLV add SOC_SINGLE_SX_TLV)
Reported-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c39df5fa37 upstream.
Commit 8aac62706a ("move exit_task_namespaces() outside of
exit_notify()") breaks pppd and the exiting service crashes the kernel:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000028
IP: ppp_register_channel+0x13/0x20 [ppp_generic]
Call Trace:
ppp_asynctty_open+0x12b/0x170 [ppp_async]
tty_ldisc_open.isra.2+0x27/0x60
tty_ldisc_hangup+0x1e3/0x220
__tty_hangup+0x2c4/0x440
disassociate_ctty+0x61/0x270
do_exit+0x7f2/0xa50
ppp_register_channel() needs ->net_ns and current->nsproxy == NULL.
Move disassociate_ctty() before exit_task_namespaces(), it doesn't make
sense to delay it after perf_event_exit_task() or cgroup_exit().
This also allows to use task_work_add() inside the (nontrivial) code
paths in disassociate_ctty().
Investigated by Peter Hurley.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Reported-by: Sree Harsha Totakura <sreeharsha@totakura.in>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: Sree Harsha Totakura <sreeharsha@totakura.in>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Andrey Vagin <avagin@openvz.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dfccbb5e49 upstream.
wait_task_zombie() first does EXIT_ZOMBIE->EXIT_DEAD transition and
drops tasklist_lock. If this task is not the natural child and it is
traced, we change its state back to EXIT_ZOMBIE for ->real_parent.
The last transition is racy, this is even documented in 50b8d25748
"ptrace: partially fix the do_wait(WEXITED) vs EXIT_DEAD->EXIT_ZOMBIE
race". wait_consider_task() tries to detect this transition and clear
->notask_error but we can't rely on ptrace_reparented(), debugger can
exit and do ptrace_unlink() before its sub-thread sets EXIT_ZOMBIE.
And there is another problem which were missed before: this transition
can also race with reparent_leader() which doesn't reset >exit_signal if
EXIT_DEAD, assuming that this task must be reaped by someone else. So
the tracee can be re-parented with ->exit_signal != SIGCHLD, and if
/sbin/init doesn't use __WALL it becomes unreapable.
Change reparent_leader() to update ->exit_signal even if EXIT_DEAD.
Note: this is the simple temporary hack for -stable, it doesn't try to
solve all problems, it will be reverted by the next changes.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Reported-by: Jan Kratochvil <jan.kratochvil@redhat.com>
Reported-by: Michal Schmidt <mschmidt@redhat.com>
Tested-by: Michal Schmidt <mschmidt@redhat.com>
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Cc: Lennart Poettering <lpoetter@redhat.com>
Cc: Roland McGrath <roland@hack.frob.com>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit cb3042d609 ]
In arch_cpu_idle() we must enable %pil based interrupts before
potentially invoking the hypervisor cpu yield call.
As per the Hypervisor API documentation for cpu_yield:
Interrupts which are blocked by some mechanism other that
pstate.ie (for example %pil) are not guaranteed to cause
a return from this service.
It seems that only first generation Niagara chips are hit by this
bug. My best guess is that later chips implement this in hardware
and wake up anyways from %pil events, whereas in first generation
chips the yield is implemented completely in hypervisor code and
requires %pil to be enabled in order to wake properly from this
call.
Fixes: 87fa05aeb3 ("sparc: Use generic idle loop")
Reported-by: Fabio M. Di Nitto <fabbione@fabbione.net>
Reported-by: Jan Engelhardt <jengelh@inai.de>
Tested-by: Jan Engelhardt <jengelh@inai.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1535bd8adb ]
When checking a system call return code for an error,
linux_sparc_syscall was sign-extending the lower 32-bit value and
comparing it to -ERESTART_RESTARTBLOCK. lseek can return valid return
codes whose lower 32-bits alone would indicate a failure (such as 4G-1).
Use the whole 64-bit value to check for errors. Only the 32-bit path
should sign extend the lower 32-bit value.
Signed-off-by: Dave Kleikamp <dave.kleikamp@oracle.com>
Acked-by: Bob Picco <bob.picco@oracle.com>
Acked-by: Allen Pais <allen.pais@oracle.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: sparclinux@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4f6500fff5 ]
In arch/sparc/Kernel/Makefile, we see:
obj-$(CONFIG_SPARC64) += jump_label.o
However, the Kconfig selects HAVE_ARCH_JUMP_LABEL unconditionally
for all SPARC. This in turn leads to the following failure when
doing allmodconfig coverage builds:
kernel/built-in.o: In function `__jump_label_update':
jump_label.c:(.text+0x8560c): undefined reference to `arch_jump_label_transform'
kernel/built-in.o: In function `arch_jump_label_transform_static':
(.text+0x85cf4): undefined reference to `arch_jump_label_transform'
make: *** [vmlinux] Error 1
Change HAVE_ARCH_JUMP_LABEL to be conditional on SPARC64 so that it
matches the Makefile.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 16932237f2 ]
This reverts commit 145e1c0023.
This commit broke the behavior of __copy_from_user_inatomic when
it is only partially successful. Instead of returning the number
of bytes not copied, it now returns 1. This translates to the
wrong value being returned by iov_iter_copy_from_user_atomic.
xfstests generic/246 and LTP writev01 both fail on btrfs and nfs
because of this.
Signed-off-by: Dave Kleikamp <dave.kleikamp@oracle.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: sparclinux@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 557fc5873e ]
The SIMBA APB Bridges lacks the 'ranges' of-property describing the
PCI I/O and memory areas located beneath the bridge. Faking this
information has been performed by reading range registers in the
APB bridge, and calculating the corresponding areas.
In commit 01f94c4a6c
("Fix sabre pci controllers with new probing scheme.") a bug was
introduced into this calculation, causing the PCI memory areas
to be calculated incorrectly: The shift size was set to be
identical for I/O and MEM ranges, which is incorrect.
This patch set the shift size of the MEM range back to the
value used before 01f94c4a6c.
Signed-off-by: Kjetil Oftedal <oftedal@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c063449394 upstream.
Commit 9cb00419fa, which enables hole punching for bigalloc file
systems, exposed a bug introduced by commit 6ae06ff51e in an earlier
release. When run on a bigalloc file system, xfstests generic/013, 068,
075, 083, 091, 100, 112, 127, 263, 269, and 270 fail with e2fsck errors
or cause kernel error messages indicating that previously freed blocks
are being freed again.
The latter commit optimizes the selection of the starting extent in
ext4_ext_rm_leaf() when hole punching by beginning with the extent
supplied in the path argument rather than with the last extent in the
leaf node (as is still done when truncating). However, the code in
rm_leaf that initially sets partial_cluster to track cluster sharing on
extent boundaries is only guaranteed to run if rm_leaf starts with the
last node in the leaf. Consequently, partial_cluster is not correctly
initialized when hole punching, and a cluster on the boundary of a
punched region that should be retained may instead be deallocated.
Signed-off-by: Eric Whitney <enwlinux@gmail.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ce37c42919 upstream.
Commit 3779473246 breaks the return of error codes from
ext4_ext_handle_uninitialized_extents() in ext4_ext_map_blocks(). A
portion of the patch assigns that function's signed integer return
value to an unsigned int. Consequently, negatively valued error codes
are lost and can be treated as a bogus allocated block count.
Signed-off-by: Eric Whitney <enwlinux@gmail.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f88ba6a2a4 upstream.
I got an error on v3.13:
BTRFS error (device sdf1) in write_all_supers:3378: errno=-5 IO failure (errors while submitting device barriers.)
how to reproduce:
> mkfs.btrfs -f -d raid1 /dev/sdf1 /dev/sdf2
> wipefs -a /dev/sdf2
> mount -o degraded /dev/sdf1 /mnt
> btrfs balance start -f -sconvert=single -mconvert=single -dconvert=single /mnt
The reason of the error is that barrier_all_devices() failed to submit
barrier to the missing device. However it is clear that we cannot do
anything on missing device, and also it is not necessary to care chunks
on the missing device.
This patch stops sending/waiting barrier if device is missing.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5acda9d12d upstream.
After commit 839a8e8660 ("writeback: replace custom worker pool
implementation with unbound workqueue") when device is removed while we
are writing to it we crash in bdi_writeback_workfn() ->
set_worker_desc() because bdi->dev is NULL.
This can happen because even though bdi_unregister() cancels all pending
flushing work, nothing really prevents new ones from being queued from
balance_dirty_pages() or other places.
Fix the problem by clearing BDI_registered bit in bdi_unregister() and
checking it before scheduling of any flushing work.
Fixes: 839a8e8660
Reviewed-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jan Kara <jack@suse.cz>
Cc: Derek Basehore <dbasehore@chromium.org>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
